- migrated /README are removed from /boards
- there are a lot of READMEs that should be further converted to rst.
At the moment they are moved to Documentation/platforms and included in rst files
Some SD card connectors do not have separate card detection pin. In that
case card detection has to be done on CD/DAT3 data line. This means
software (i.e. architecture level driver) has to take care of pin
configuration switching (pin has to be set as data pin in case of
transfer and as interrupt card detection pin when there is no action
on data line).
This commit adds CD/DAT3 line card detection support for SAMv7 MCU.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
The class device only handles descriptor information specific to the class,
and shared descriptor information is passed through parameters and
handled by the composite driver.
Signed-off-by: zhangyuan21 <zhangyuan21@xiaomi.com>
When I try to set priorities in certain programs, such as init_priority(HIGH_PRIORITY), I've noticed that during linking, there's no guarantee that the programs will be compiled in the sequence I've specified based on priority. This has led to some runtime errors in my program.
I realized that in the ld file, when initializing dynamic arrays, there's no assurance of initializing init_array.* before init_array. This has resulted in runtime errors in the program. Consequently, I've rearranged the init_array.* in the ld file of NuttX to be placed before init_array and added a SORT operation to init_array.* to ensure accurate initialization based on priorities during linking.
replace *(.init_array .init_array.*) with KEEP(*(.init_array .init_array.*)).
The KEEP statement within a linker script will instruct the linker to keep the specified section, even if no symbols inside it are referenced. This statement is used within the SECTIONS section of the linker script. This becomes relevant when garbage collection is performed at link time, enabled by passing the --gc-sections switch to the linker. The KEEP statement instructs the linker to use the specified section as a root node when creating a dependency graph, looking for unused sections. Essentially forcing the section to be marked as used.
Signed-off-by: cuiziwei <cuiziwei@xiaomi.com>
SAMv7 encoder driver with GPIO pins was written without IOCTL support.
While this driver does not require any lower level IOCTLs for its
functionality the upper layer fails on assertion when unknown command
can not be send to lower layer. This commit adds IOCTL handler that
always returns -ENOTTY as no commands are supported.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
use PTHREAD_CLEANUP_STACKSIZE to enable or disable interfaces pthread_cleanup_push() and pthread_cleanup_pop().
reasons:(1)same as TLS_TASK_NELEM (2)it is no need to use two variables
Signed-off-by: yanghuatao <yanghuatao@xiaomi.com>
Board related code may use different mounts for MTD device (block
character for one, SmartFS for another) if required by the board.
Additional type member was therefore added to mtd_partition_s structure
in order to support this.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
The original code hard-coded card detection to the low when card is
inserted and high when not. This might not be true on every board
because it depends on the slot and wiring used. The second reason is
because it is also possible to detect card with D3 pin pull-up when the
slot does not provide dedicated card detection switch.
This introduces new argument to the sam_hsmci_initialize to allow
invert of card detection pin. It also applies this invert to existing
boards as that was the state up to this point.
This commit adds configuration file with enabled MCAN support. This is
mainly to track changes in architectural driver that could cause build
errors.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds support for GPIO driver based encoder for SAMv7 boards.
This encoder do not use the microcontroller's dedicated driver but two
GPIO pins with interrupts. The position is calculated based on those
interrupts.
This can be used for boards that do not have pins routed to the dedicated
driver.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
In order to support multiple LCD instances per board, add a pointer from
lcd_planeinfo_s to the lcd_dev_s which it belongs to. Also enhance the
putrun, getrun, putarea and getarea methods to pass through the
lcd_dev_s pointer to the respective device driver.
Port all LCD device drivers to this lcd_planeinfo_s extension.
Enhance SSD1306 driver to support multiple LCDs.
Signed-off-by: Michael Jung <michael.jung@secore.ly>
Selecting this option will pass "-Map=$(TOPDIR)$(DELIM)nuttx.map" to ld
when linking NuttX ELF. That file can be useful for verifying
and debugging magic section games, and for seeing which
pieces of code get eliminated with DEBUG_OPT_UNUSED_SECTIONS.
Signed-off-by: chao.an <anchao@xiaomi.com>
since it is broken and inefficient, and then removed by:
commit dc961baaea
Author: chao.an <anchao@xiaomi.com>
Date: Thu Apr 14 18:07:14 2022 +0800
arm/armv7-[a|r]: move fpu save/restore to assembly handler
Save/Restore FPU registers in C environment is dangerous practive,
which cannot guarantee the compiler won't generate the assembly code
with float point registers, especially in interrupt handling
Signed-off-by: chao.an <anchao@xiaomi.com>
commit 8d66dbc068
Author: chao.an <anchao@xiaomi.com>
Date: Thu Apr 7 13:48:04 2022 +0800
arm/armv[7|8]-m: skip the fpu save/restore if stack frame is integer-only
Signed-off-by: chao.an <anchao@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
