boards: cxd56xx: add SCU sensors
* drivers: platform: add Avago APDS9930 Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BH1721FVC Ambient Light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BH1745NUC Color Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BM1383GLV/BM1383AGLV Pressure Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm BM1422GMV/BM1422AGMV Magnetic Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Bosch BMI160 Sensor support
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Bosch BMP280 Barometic Pressure Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Kionix KX022/KX122 Acceleration Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Murata LT1PA01 Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: spresense: add Rohm RPR0521RS Proximity and Ambient light Sensor
This sensor is connected to the SCU on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: sensors: bmi160: add optional I2C address
Add a menu option for the case when the SDO pin is pulled to VDDIO
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add support for 4-byte addressing on >128Mb Macronix flash parts
* Save CONFIG_ARCH_BOARD_CUSTOM when running 'make savedefconfig'
* Only use PCLKSEL0 for ADC on LPC176x family.
* Made grep search expression more specific.
* Added missing '=' to second grep
* Revert "Only use PCLKSEL0 for ADC on LPC176x family."
This reverts commit 835b5e9d6fcbea02cb0203c063b0e121fa57ba9e.
* Revert "Added missing '=' to second grep"
This reverts commit 38b51f0c6d9612de755c102a53846ca7488cdf14.
* Added a missing '=' in the second grep statement
* Added support for 4-byte addressing on >128Mb Macronix flash parts
Approved-by: Gregory Nutt <gnutt@nuttx.org>
register a character driver for UUID of AT24CSxx chips
Allows the UUID to read as a file or displayed from an nsh prompt
with: hexdump /dev/eeprom.uuid
Approved-by: Alan Carvalho de Assis <acassis@gmail.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
boards: add stub drivers folder for later use
* boards: add stub drivers folder for later use
The board/drivers folder is added for future use.
In this folder we should place drives that are platform specific and
depend on HW that is present only on a specific platform.
NOTE: All shared drivers should go to the regular driver folder
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tools: shift BOARD_DIR one level up
In preparation for drivers and common folders we are moving the
BOARD_DIR path up one level.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* tools: add drivers/platform symlink
Link the boards/<arch>/<chip>/drivers dir to drivers/platform
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: add platform specifc drivers extension
There are platforms that use specific drivers and we should be able to
include those drivers in the build
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* board: cxd56xx: drivers: add AK09912 driver for SCU
This is a platform specific driver connected on the SCU unit.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
xbee: Fixes one instance of the use of IOBUSER_WIRELESS_MAC802154 which isn't available without the software MAC layer. Instead we use IOBUSER_WIRELESS_RAD802154 throughout the whole driver since it is always available when IEEE 802.15.4 support is enable
Approved-by: Gregory Nutt <gnutt@nuttx.org>
drivers/ieee802154/xbee: Add configuration option for setting the default prefix to use when bringing up the network and setting the IP address.
# Conflicts:
# drivers/wireless/ieee802154/xbee/xbee_netdev.c
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Iobinstrumentation
* mm/iob: Introduces producer/consumer id to every iob call. This is so that the calls can be instrumented to monitor the IOB resources.
* iob instrumentation - Merges producer/consumer enumeration for simpler IOB user.
* fs/procfs: Starts adding support for /proc/iobinfo
* fs/procfs: Finishes first pass of simple IOB user stastics and /proc/iobinfo entry
Approved-by: Gregory Nutt <gnutt@nuttx.org>
This typically happens when there is a lot of data being received over the link. When the XBee stops responding, many times, querying the XBee kicks it out of this state. However, occasionally the XBee is completely locked up and the XBee has to be reset. This change handles these conditions by periodically (if not naturally occuring) querying the XBee. If during any query, the XBee does not respond within a certain number of attempts, the XBee is reset.
ieee802154/sixlowpan: Removes unnecessary conversions that were happening due to a misunderstanding of byte ordering with EUI-64
# Conflicts:
# drivers/wireless/ieee802154/xbee/xbee_netdev.c
Approved-by: Gregory Nutt <gnutt@nuttx.org>
wireless network devices: Attach radio to d_buf before registering device to handle forwarding case.
When CONFIG_NET_IPFORWARD is enabled, and CONFIG_NET_6LOWPAN is being used, a packet that attempts to get forwarded on the 6LoWPAN interface will require that the radio's buffer be attached to d_buf. Otherwise the below exception will be hit.
~line 542 of sixlowpan_framelist.c
```
/* Recover the reassembly buffer from the driver d_buf. */
reass = (FAR struct sixlowpan_reassbuf_s *)radio->r_dev.d_buf;
DEBUGASSERT(reass != NULL);
```
The underlying "radio" in this case is the mac802154_netdev.
This behavior has probably not been observed because the buffer is normally attached in the periodic txpoll worker. However, in my case, the 6LoWPAN interace was not UP yet, and therefore the worker hadn't run yet.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
ieee802154: Support dynamic FCS length. Adds IEEE802154_ATTR_PHY_FCSLEN.
This change introduces IEEE802154_ATTR_PHY_FCSLEN which the radio layer can support to set/get the FCS length that's added to the end of the frame. One use case, in promiscuous mode, is to add back in the FCS of the received frame by increasing the iob->io_len by the FCS length.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
wireless/ieee8021254: Adds support for energy detect.
Adds support for energy detect by introducing a new radio call/callback, as the PHY layer is required to perform the energy detect.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Master
* Revert "Merged in yanqil-br/feature-multi_chan_pwm (pull request #973)"
This reverts commit aef0e0b538.
* arch/arm/src/{stm32/stm32f7/stm32h7/stm32l4}/stm32_pwm.c: configure multi-channel duty only if channel specified. This allows you to update duty cycle for a single channel
* nucleo-f303re/configs: add basic NSH configuration
* nucleo-f303re/configs/pwm: enable console on UART2 and set entry point to nsh_main
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
