Summary:
- This commit fixes to handle address info in accept() in gs2200m.c
Impact:
- All use cases which use accept() with gs2200m
- Need to update apps/wireless/gs2200m as well
Testing:
- Tested with spresene:wifi
- Tested with telnet daemon
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>>
Summary:
- This commit fixes to handle UDP connect() with bind() to a local port.
Impact:
- All UDP cases which use connect() with gs2200m
- Need to update apps/wireless/gs2200m as well
Testing:
- Tested with spresense:wifi
- Create a UDP socket and bind() to a local port.
- Then connect() to remote address with port and send()
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Summary:
- This commit fixes compile errors if CONFIG_DEBUG_ASSERTIONS=y
Impact:
- Affects noteram_driver only
Testing:
- Tested with spresense:wifi_smp with CONFIG_DEBUG_ASSERTIONS=y
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
This adds support for the Q10 BlackBerry based keyboard
from Solder Party. https://www.solder.party/docs/keyboard-pmod/
They keyboard device registered at /dev/kbdN is fully compatible
with hidkbd and has been testing with the Keyboard FeatherWing
on the nRF52 platform.
The buttons are added as a standard discrete joystick if
optionally enabled. The PMOD variant of this does not
include these buttons, but the Keyboard FeatherWing does.
This joystick is usually defined at /dev/djoyN and
can be used with the djoy example application.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
This patch resolves to bugs in the GPIO interrupt logic:
1. Any pins did not have STMPE811_GPIO_RISING in their pincfg
would clear the rising edge interrupt enable flag for all
pins due to a masking bug.
2. Pins would never trigger a second interrupt. There is an
undocumented requirement that you have to clear both the
GPIO interrupt status register __and__ also the edge
detection status register. Failure to clear either of
these will result in no further interrupts being triggered.
This requirement exists both for edge and level modes of
operation.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Summary:
- This commit applies NET_LL_IEEE80211 to gs2200m.c
- Also selects DRIVERS_IEEE80211 in Kconfig
Impact:
- Affects use cases with gs2200m driver
Testing:
- Tested with spresense:wifi and spresense:wifi_smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
The WS2812 is very common in LED strips as it is an integrated
controller and LED. It is driven by a single data line, but
the timing requirements can be met by using most SPI controllers
and the use of DMA.
This driver has been validated on the nRF52 arch both with a
single LED and a strip of 144.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Summary:
- This commit fixes warnings when we remove noreturn from _assert()
Impact:
- Should have no impact
Testing:
- Tested with spresense:wifi
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
The Multiblock write path was missing the
the SDIO_WAITENABLE with SDIOWAIT_WRCOMPLETE.
This could be seen with debugging turned on as
mmcsd_eventwait: ERROR: Awakened with 10
mmcsd_transferready: ERROR: mmcsd_eventwait for transfer ready failed: -5
If the buffer to be flushed isn't multipled by the erase size,
let's pad the buffer proactively to avoid the allocation in ftl.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I6d7904aafab93a7886a594319d65826b81cd3cd1
3Change-Id: I88276149cc7826e7416929ca60b06314e96079a6
Summary:
- Remove unnecessay code from gs2200m_irq()
- Fix irq control in case that work_available() returns false
Impact:
- All use cases with gs2200m driver
Testing:
- Tested with spresense:wifi
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
When CONFIG_MMCSD_MULTIBLOCK_DISABLE is lit, all SD
read/write failed. The function return the number of
blocks in `ret`, set on entry to nsectors. That was
then wiped out by using the ret for the mmcsd_takesem.
Since the code had many path setting return, the choices for
the fix could have been add a new varaible or simple init it
were used. I choose the latter.
