configs: spresense: add I2CTOOL support and extend GPIO for future use
* arch: arm: cxd56xx: add delay support
add delay support for cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: register I2C busses
for development is usefull to register I2C busses when the I2CTOOL
is built
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs:spresense: enable GPIO interface
enable GPIO interface on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: SCU, ADC, I2C
* nuttx: configs: spresense: LEDS: fix warnings
In the initial code several errors were missed because I pushed
the dirty code.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Sensor Control Unit (SCU)
Add Sensor Control Unit (SCU) on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add I2C support
add I2C support on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add ADC interface support
Add ADC interface support on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: Use DMAC for reading sensing data
Use DMAC for reading sensing data from SCU on cxd56xx chip
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: code style sanitization
NuttX does not use Deoxygen for documentation and no file should contain Doxygen tags or Doxygen style comments.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable I2CDEV
add enable I2CDEV for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add notification LEDs
Add usefull diagnostic LEDs on the speresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add UID support
* arch: arm: cxd56xx: add UID support
Add support to be able to read the HW UID
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable USERLEDS
add USERLED for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: PM and PWM
* configs: spresense: add SPI configuration
add SPI configuration for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add support for PWM
add support for PWM for cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable PWM support
enable PWM support on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Power Management PROCFS support
the powermanager procfs support will export
/proc/pm:
clock
power
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable powermanager procfs support
The powermanager procfs is disabled by default and need to be enabled
by the CONFIG_CXD56_PM_PROCFS option
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add timer driver
Add timer driver for cxd56xx.
NOTE
The timer allows a divider of 1, 16 and 256 options
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Watch Dog Timer
Add Watch Dog Timer on cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable timer
the platform support has been added and now we can use the timers
on spresense board.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: enable WatchDog timer
The platform support has been added and now we can use the WatchDog
Timer on spresense board.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
stm32 h7 Add ADC and a few fixes for timer and Serial
* stm32h7:Fix error when SINGLEWIRE or CONFIG_STM32H7_SERIALBRK_BSDCOMPAT defined
* stm32h7:time fixed compile errors with TIM13,TIM14, TIM7
* stm32h7:Added ADC Driver
* stmh7x3:Added ADC pins to pin map
* stm32h7:Added ADC clocking
* nucleo-h743zi:Add ADC
Approved-by: Gregory Nutt <gnutt@nuttx.org>
rndis on spresense
* arch/arm/src/cxd56xx: Fix ep0 out packet handling in cxd56_usbdev.c
This change fixes to handle ep0 out packet which exceeds EP0_MAXSIZE.
For example, 76 bytes of out packet is sent from rndis host during
rndis negotiation and finally the packet is split into two out packets
(64 bytes out packet + 12 bytes out packet). To handle these packets,
actual ep0reqlen is stored during ep0 out setup stage, and if all
out packets are received, it dispatches to cxd56_ep0setup(), otherwise,
it sets up the internal USB DMA to receive remaining out packets.
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
* configs/spresense: Add support for rndis configuration
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Add syscontrol for cxd56xx
* arch: arm: cxd56xx: add sysctl
Add the syscontrol implementation for cxd56xx.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: timer updates
Add the function to change the clock speed.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: cxd56_uart updates
Add pinctrl and clock ctrl functionality.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add conditional for SDHCI
The cxd56_sdhci should be built only if CONFIG_CXD56_SDIO is selected
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add Power Management support
* arch: arm: cxd56xx: add Power Management support
Add power management on the cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add Far API
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add support for USB and SDIO
* arch: arm: cxd56xx: add support for USB connectivity
Add basic support for USB connectivity
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arch: arm: cxd56xx: add SDHCI support
We add SDHCI driver for the cxd56xx
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
arch: arm: cxd56xx: add Package Configuration
The CXD56xx can come in FCBGA 185 pin or WLCSP 100 pin package.
For each package we have to pick the right pin setup.
The default configuration is set to FCBGA 185 pin package
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Improvements for STM32 PWM
arch/arm/src/stm32/stm32_pwm: add support for all PWM modes
arch/arm/src/stm32/stm32_pwm: add interface to change PWM mode
arch/arm/src/stm32/stm32_pwm: refactor pwm_mode_configure()
arch/arm/src/stm32/stm32_pwm: STM32_PWM_CHANx corresponds to the timer channel and STM32_PWM_OUTx corresponds to the timer channel output
arch/arm/src/stm32/stm32_pwm: add CHAN5 and CHAN6 to PWM_TIMx_NCHANNELS
arch/arm/src/stm32/stm32_pwm: calculate the PWM_TIMx_NCHANNELS if CONFIG_STM32_PWM_MULTICHAN is selected
Approved-by: Gregory Nutt <gnutt@nuttx.org>
