Commit Graph

178 Commits

Author SHA1 Message Date
nuttxs
fbb2e5f781 boards/esp32s3_lan9250: deinitialize the ethernet device lan9250 for esp32s3. 2024-08-24 11:19:00 +08:00
Windrow14
b27bf82b6e Documentation/platforms/xtensa/esp32s3/boards/esp32s3-devkit|esp32s3-korvo-2: document update for sdmmc support
boards/xtensa/esp32s3/esp32s3-devkit|esp32s3-korvo-2/configs/sdmmc/defconfig: defconfig for sdmmc support

Add description for sdmmc support on esp32s3 in the board specific documentation.
Add defconfig for esp32s3-devkit with external adapter and emmc module.
Add defconfig for esp32s3-korvo-2 with SD slot enabled.

Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
2024-08-23 20:21:49 +08:00
Tiago Medicci Serrano
5680e9d5a4 espressif: Update internal libraries reference
Update internal reference to get the most updated Espressif's
libraries. Those libraries are based on branch `release/v5.1` of
the ESP-IDF and include `v5.1.4` version of it.
2024-08-21 23:28:45 +08:00
Windrow14
190c8787ff arch/xtensa/src/esp32s3/Kconfig|Make.defs|esp32s3_sdmmc.c,
arch/xtensa/src/esp32s3/hardware/esp32s3_sdmmc.h|esp32s3_soc.h,
boards/xtensa/esp32s3/common/include/esp32s3_board_sdmmc.h,
boards/xtensa/esp32s3/common/src/Make.defs|esp32s3_board_sdmmc.c,
boards/xtensa/esp32s3/esp32s3-devkit/src/esp32s3_bringup.c: add SD/mmc driver

Support 1-bit bus width and 4-bit bus width. Support eMMC high speed SDR mode.
Support transfer data with DMA. Support SD clock frequency up to 40MHZ.

Signed-off-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Jacky Cao <Jacky.Cao@sony.com>
Tested-by: Yinzhe Wu <Yinzhe.Wu@sony.com>
2024-08-19 19:52:39 +08:00
YAMAMOTO Takashi
d9c90eef13 esp32s3-devkit/toywasm: enable ESP32S3_SPI_FLASH_SUPPORT_PSRAM_STACK 2024-08-07 15:59:41 +08:00
Tiago Medicci
93322a50fe boards/esp32s3: Add initial support to the ESP32-S3-Korvo-2 board
The ESP32-S3-Korvo-2 is a multimedia development board based on the
ESP32-S3 chip. It is equipped with a two-microphone array which is
suitable for voice recognition and near/far-field voice wake-up
applications. The board integrates multiple peripherals such as
LCD, camera, and microSD card. It also supports JPEG video stream
processing. With all of its outstanding features, the board is an
ideal choice for the development of low-cost and low-power
network-connected audio and video products.
2024-08-01 16:04:53 +08:00
Tiago Medicci Serrano
016bc47a63 esp32s3/elf: Enable ELF loader for ESP32-S3
Provide `up_copy_section` function that enables copying data using
the data bus. If the memory destination address is accessible
through the instruction bus, the data is copied using the
correspondent address accessible through the data bus.
2024-07-31 02:33:12 +08:00
Tiago Medicci Serrano
c91599d34c esp32s3/i2s: Fix faulty initialization when SMP is enabled
The buffer initialization function (`i2s_buf_initialize`) calls
`i2s_buf_free`, which performs buffer initialization within a
critical section (`spin_lock_irqsave`). If this function is called
under the same critical section (same spinlock), initialization
will hang.
2024-07-30 01:44:57 +08:00
Eren Terzioglu
98f5d6adc5 esp32[s2|s3]: Add temperature sensor support 2024-07-27 14:12:44 -03:00
Filipe Cavalcanti
91dfd20eaf arch/xtensa: add support for brushed DC motor control
arch/xtensa: add support for capture driver on ESP32 and ESP32|S3|

Squashed:
Initial settings for MCPWM Capture on board level
Created lower half files - compilation ok
Using capture debug features. Simple example on fops works
Successful duty and freq calculation
Documentation update
Fixed and added interupt capabilities for all 3 capture channels
Cleaned defconfig
Renamed macros, added S3 options and moved arch source to common dir
Added support for ESP32S3
Added capture example to defconfig and renamed

Basic bring up ready. New Kconfig options for motor.

Good motor registration

Working on enabling pwm generators

Working on enabling pwm generators

Added fops functions

Success on PWM 50%

stable pwm operation for bdc

Added loopback option for testing

Improved rules on fsm

Working motor direction control

Testing new ISR for fault handling

Issues on fault ISR

Removed fault implementation (not working)

Added support for esp32s3

Documentation improvements

Added default motor spin direction

Added parameter change while running

Review fixes

arch/xtensa: add support for fault signal on motor control

Squashed:
Initial settings for MCPWM Capture on board level
Created lower half files - compilation ok
Using capture debug features. Simple example on fops works
Successful duty and freq calculation
Documentation update
Fixed and added interupt capabilities for all 3 capture channels
Cleaned defconfig
Renamed macros, added S3 options and moved arch source to common dir
Added support for ESP32S3
Added capture example to defconfig and renamed

Basic bring up ready. New Kconfig options for motor.

Good motor registration

Working on enabling pwm generators

Working on enabling pwm generators

Added fops functions

Success on PWM 50%

stable pwm operation for bdc

Added loopback option for testing

Improved rules on fsm

Working motor direction control

Testing new ISR for fault handling

Issues on fault ISR

Removed fault implementation (not working)

Added support for esp32s3

Documentation improvements

Added default motor spin direction

Added parameter change while running

Got responsive fault indicator

Working brakes - still need to work on starting isr

Fixed single-time ISR initializiation

Working soft brake on fault

Improved KConfig for BDC and BLDC

Kconfig fixed at board level
2024-07-27 12:08:51 +08:00
Huang Qi
f555b3de91 boards/esp32s3: Increse the default stack size for usbnsh
Fix https://github.com/apache/nuttx/issues/12712

If run nsh over usb based serial port, the default stack size is too small,
for example simple `ps` command will use more than 2208 bytes stack.

Then the stack overflow will happen and the system will hang here.

Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
2024-07-17 15:08:17 +08:00
Huang Qi
d2347aea2f boards/esp32[c3|c6|h2|s2|s3]: Ignore etctmp in common board
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
2024-07-12 01:01:15 +08:00
YAMAMOTO Takashi
881f749777 refresh esp32s3-devkit:qemu_debug
after https://github.com/apache/nuttx/pull/12639
2024-07-10 23:38:17 +08:00
YAMAMOTO Takashi
e6f35007f0 esp32s3-devkit: add a config for qemu
based on esp32s3-devkit:toywasm, tailored for the espressif fork
of qemu. [1]

* disabled a few things for which emulation doesn't seem available:

  * wifi
  * spiram
  * ESP32S3_SYSTEM_BBPLL_RECALIB

* enabled DEBUG_SYMBOLS for my convenience (thus _debug suffix)

* enabled hostfs for my convenience

tested with:
qemu-xtensa-softmmu-esp_develop_9.0.0_20240606-x86_64-apple-darwin.tar.xz

[1] https://github.com/espressif/qemu
2024-07-10 00:06:18 +08:00
Alan Carvalho de Assis
82946d0d5f net: Enable ICMP by default if IPv4 is enabled
Signed-off-by: Alan C. Assis <acassis@gmail.com>
2024-07-09 17:08:27 +08:00
Almir Okato
6ec690cbfc esp32[s2|s3]: move rom segments mapping to espressif common folder
Move and unify map_rom_segments function called when starting
Simple Boot and MCUboot compatible images.

Signed-off-by: Almir Okato <almir.okato@espressif.com>
2024-07-04 18:22:24 -03:00
Filipe Cavalcanti
365e9e967c arch/xtensa: add support for capture driver on ESP32 and ESP32|S3|
Squashed:
Initial settings for MCPWM Capture on board level
Created lower half files - compilation ok
Using capture debug features. Simple example on fops works
Successful duty and freq calculation
Documentation update
Fixed and added interupt capabilities for all 3 capture channels
Cleaned defconfig
Renamed macros, added S3 options and moved arch source to common dir
Added support for ESP32S3
Added capture example to defconfig and renamed
2024-06-27 18:14:59 +08:00
Devansh Purohit
0ffbff84d1 Changed ESP32S3 Chip names based on their configuration and added ESP32S3_CUSTOM chip module
As suggested in PR:12530, changed the default names of ESP32S3WROOM chips to ESP32S3WROOM1N4,
ESP32S3WROOM2N16R8, ESP32S3WROOM2N32R8, ESP32S3MINI1N8.
Also regenerated all the defconfigs for board configurations.
Added a custom ESP32S3 module for custom flash configurations.
Declared ESP32S3_PSRAM_8M variable with prompt
2024-06-21 17:55:42 +08:00
Tiago Medicci Serrano
96f83bb03a net: Enable CONFIG_NET_ARP_SEND by default
Enable logic to send ARP requests if the target IP address mapping
does not appear in the ARP table.

Please check the comment in https://github.com/apache/nuttx/issues/12446#issuecomment-2145856778
2024-06-06 02:40:16 +08:00
Almir Okato
16f8966fa9 esp32s2: add simple boot support
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.

This commit also removes deprecated code and makes this bootloader
configuration as default for esp32s2 targets and removes the need
for running 'make bootloader' command for it.

Signed-off-by: Almir Okato <almir.okato@espressif.com>
2024-06-04 18:53:14 -03:00
simbit18
97836bf3ab board: esp32c3, esp32 and esp32s3 corrected PM block
removed depends on PM from if PM block
2024-05-27 23:24:31 +08:00
Tiago Medicci Serrano
0ed714bba4 esp32s3/adc: Update the bootloader configuration for ESP32-S3
Avoid using the legacy bootloader in case it isn't required. Use
the simple boot instead.
2024-05-10 01:44:02 +08:00
YAMAMOTO Takashi
1b5b9845f4 esp32s3-devkit/toywasm: use ARCH_CHIP_ESP32S3WROOM2_32M
As documented in [1], this config is for a board with 32MB flash.

[1] Documentation/platforms/xtensa/esp32s3/boards/esp32s3-devkit/index.rst
2024-05-10 01:44:02 +08:00
Tiago Medicci Serrano
8dca62f8f9 esp32s3: Limit MTD partition size according to the flash size
Whenever a MTD partition is set, this change limits its size
according to the flash size, avoiding the MTD partition to be
greater than the actual flash size.
2024-05-10 01:44:02 +08:00
nuttxs
8d3d93e001 Add ESP32-S3 ADC driver 2024-05-07 01:12:05 +08:00
Xu Xingliang
0db7417dc0 esp32/lvgl: fix lvgl v9 configuration error
Signed-off-by: Xu Xingliang <xuxingliang@xiaomi.com>
2024-04-30 01:45:03 +08:00
Xu Xingliang
62c2b3e1ec lvgl: update existing config to use lvgl v9
These configs are changed based on below rules.
1. always enable +CONFIG_LV_USE_NUTTX=y
2. If touchpad is used, enable +CONFIG_LV_USE_NUTTX_TOUCHSCREEN=y
3. enable log by +CONFIG_LV_USE_LOG=y
4. If -CONFIG_LV_MEM_CUSTOM=y previously defined, replace it with +CONFIG_LV_USE_CLIB_MALLOC=y +CONFIG_LV_USE_CLIB_SPRINTF=y +CONFIG_LV_USE_CLIB_STRING=y
5. If -CONFIG_LV_PORT_USE_FBDEV=y, default config is for fbdev. If -CONFIG_LV_PORT_USE_LCDDEV=y, +CONFIG_LV_USE_NUTTX_LCD=y
6. Remove all -CONFIG_LV_TICK_CUSTOM=y -CONFIG_LV_TICK_CUSTOM_INCLUDE="port/lv_port_tick.h"
7. If -CONFIG_LV_PORT_LCDDEV_DOUBLE_BUFFER=y, replace it with CONFIG_LV_NUTTX_LCD_DOUBLE_BUFFER=y. For fbdev, double buffer is automatically detected.
8. If -CONFIG_LV_COLOR_16_SWAP=y, need to upgrade the LCD driver to support hardware byte order swap.

Signed-off-by: Xu Xingliang <xuxingliang@xiaomi.com>
2024-04-29 10:06:43 +08:00
chenwen@espressif.com
ea5583b112 xtensa/esp32s3: Support ESP32-S3 PM standby and sleep.
1. pm configuration demonstrates the use of power management present on the ESP32-S3.
   2. You can use the pmconfig command to test the power management, for details look at
      ``Documentation/platforms/xtensa/esp32s3/boards/esp32s3-devkit/index.rst``

Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
2024-04-25 13:43:15 +08:00
Almir Okato
a5de4dbd22 xtensa/esp32s3: Add missing entries to iram.text from legacy_sections.ld
Signed-off-by: Almir Okato <almir.okato@espressif.com>
2024-04-24 09:46:04 +08:00
Almir Okato
d098c1dc87 esp32s3: add simple boot support
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.

This commit also removes deprecated code and makes this bootloader
configuration as default for esp32s3 targets and removes the need
for running 'make bootloader' command for it.

Other related fix, but not directly to Simple Boot:
- Instrumentation is required to run from IRAM to support it during
initialization. `is_eco0` function also needs to run from IRAM.
- `rtc.data` section placement was fixed.
- Provide arch-defined interfaces for efuses, in order to decouple
board config level from arch-defined values.

Signed-off-by: Almir Okato <almir.okato@espressif.com>
2024-04-17 19:43:05 +08:00
simbit18
7677f10d3f fix nxstyle
fix Relative file path does not match actual file.
2024-04-16 19:09:12 +08:00
simbit18
b0504f1e5e fix nxstyle
fix Relative file path does not match actual file.
2024-04-15 15:33:17 -03:00
Tiago Medicci Serrano
9520edeb16 espressif/rmt: Fix minor issues regarding formatting and comments
This commit only fix minor issues regarding formatting and comments
2024-04-02 14:50:59 -03:00
chenwen@espressif.com
ffc7442af2 xtensa/esp32s3: Add ESP32-S3 AES driver
1. Support AES-128/AES-256 encryption and decryption

Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
2024-03-28 09:34:04 +08:00
Tiago Medicci Serrano
1d645318cc esp32s3/rmt: Define default receiver device for the RMT peripheral
This enables using the example without needing to pass a different
argument for the receiver.
2024-02-19 19:02:34 -08:00
Tiago Medicci Serrano
641a0df27f esp32s3: Improve selection of the bootloader being used on Kconfig
- A pre-built IDF bootloader is used by default;
- `ESP32S3_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S3_PARTITION_TABLE.
2024-01-25 11:22:39 -03:00
w2016561536
829ec6d5e4 esp32s3/pwm: Fix pwm output
1. Fix pwm output always low problem.
2. Add multi channel support in defconfig
2024-01-17 22:42:08 -03:00
w2016561536
6a0eeb1b3e esp32s3/spi: Add SPI bus init in bringup and fix SPI bus 2 and 3 conflict
1. Add spi bus init in esp32s3_bringup.c
2. Fix IOMUX conflict between spi bus 2 and 3
3. Add spi defconfig
4. Follow the standard of NuttX
2024-01-17 09:29:20 -03:00
Tiago Medicci Serrano
f4485a58e3 esp32s3_devkit/sta_softap: Reenable SMP on defconfig.
This reverts commit e25fcb3bd5.
The issue - related to a deadlock in the RT-Timer - was properly
solved.
2024-01-11 09:22:52 +09:00
Tiago Medicci Serrano
000bf2a7c7 esp32s3/rmt: Use the Espressif's common RMT driver.
This commit use the new common RMT driver for all Espressif's
xtensa-based chips on ESP32-S3.
2023-12-24 16:38:06 -08:00
Tiago Medicci Serrano
1ca460c89a esp32s3: Fully integrate Espressif HAL repository to ESP32-S3
By integrating the Espressif`s HAL repository into the current
ESP32-S3 implementation on NuttX, it is possible to call functions
that make it easier to set up the registers of the ESP32-S3 and
enables the usage of common Espressif drivers. Please note that
Espressif's HAL repository was already being used for the Wi-Fi
driver. Then, this commit includes other source files to be used
by other drivers other than Wi-Fi and reorganize the build process.
2023-12-24 16:38:06 -08:00
Tiago Medicci Serrano
65d736bfc1 esp32<|s2|s3>_board_spiflash: Substitute fs messages to syslog
Once these messages are thrown during the system's bring-up, it is
advisable them to be output by the syslog considering the file
system initialization.
2023-12-18 09:01:15 -08:00
Tiago Medicci Serrano
908bac55f3 esp32<|s2|s3>_board_spiflash: Fix error message about SmartFS init
The SmartFS partition needs to be formatted before being mounted.
Otherwise, it would throw an error message. The error message now
contains a suggestion to format the partition when such an error
is detected.
2023-12-18 09:01:15 -08:00
simbit18
c494ce4a96 Update kconfig2html.c
Fix nuttx coding style
2023-12-14 20:02:52 -08:00
chenwen@espressif.com
62a6a0ab4d xtensa/esp32s3: Tasks use SPIRAM as stack can do SPI flash read/write/erase/map/unmap
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
2023-12-12 22:10:38 -08:00
Xiang Xiao
ca5a9c711a Remove @ and % tag from all comments
and format the multiple line comments

Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
2023-12-11 17:00:10 -03:00
anjiahao
25f599fe31 add demo for record stack defconfig
xtensa: esp32s3-devkit:stack
arm: stm32f429i-disco:stack

Signed-off-by: anjiahao <anjiahao@xiaomi.com>
2023-12-11 02:06:51 -08:00
Dong Heng
bf54a5ae50 driver/net/lan9250: Add LAN9250 driver(SPI and QSPI mode) 2023-12-07 19:53:05 -08:00
YAMAMOTO Takashi
cc0dd4c8a4 add esp32s3-devkit:toywasm kconfig 2023-12-07 08:21:39 -08:00
Eren Terzioglu
9c793067cc xtensa/esp32s3: Fix esp32s3 mcuboot ota crash 2023-12-01 18:48:10 -08:00