1. Configurable mapping of virtual address to psram physical address
2. Access SPIRAM memory at high physical address through bank switching
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
1. If CONFIG_ESP32S3_PHY_INIT_DATA_IN_PARTITION and CONFIG_ESP32S3_SUPPORT_MULTIPLE_PHY_INIT_DATA are enabled,
PHY initialization data (PHY initialization data is used for RF calibration) will be loaded from a partition.
2. The corresponding PHY init data type can be automatically switched according to the country code,
China's PHY init data bin is used by default, country code can be modified through the wapi command: wapi country <ifname> <country code>.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
During PSRAM initialization and flash operations, the Cache needs to be disabled.
So all data and code for the aforementioned scope is required to be placed in Internal RAM.
After https://github.com/apache/nuttx/pull/11007/ was merged, the
path for some files changed, requiring the linker to be fixed to
make it run from the internal memory once again.
This commit sets the BLE's interrupt as a IRAM-enabled interrupt,
which enables it to run during a SPI flash operation. This enables
us to create a cache to off-load semaphores and message queues
operations and treat them when the SPI flash operation is finished.
By doing that, we avoid packet losses during a SPI flash operation.
This commit provides an interface to register ISRs that run from
IRAM and keeps track of the non-IRAM interrupts. It enables, for
instance, to avoid disabling all the interrupts during a SPI flash
operation: IRAM-enabled ISRs are, then, able to run during these
operations.
The board-level GPIO support is different from the already existing
button and LEDC support because it enable us to register the GPIO
pins as devices in `/dev/gpioX`. Some applications are able to use
this interface to read and write the GPIO pins.
Documentation was added regarding its usage. Please check
`Documentation/platforms/xtensa/esp32s3/boards/esp32s3-devkit/index.rst`
Provide initial support for audio through the I2S peripheral to the
CS4344 audio codec on ESP32-S3-DevKitC-1 board.
Please check documentation for usage examples.
ESP32-S3 has only one 2.4 GHz ISM band RF module, which is shared
by Bluetooth and Wi-Fi, so Bluetooth can’t receive or transmit data
while Wi-Fi is receiving or transmitting data and vice versa.
Under such circumstances, ESP32-S3 uses the time-division
multiplexing method to receive and transmit packets.
- Added Wi-Fi related symbols to the kernel-space linker;
- Allocate more RAM to the kernel (to be useb by the Wi-Fi driver).
- Create a specific defconfig.
Instead of setting kernel/user space instruction and data ROM as
hard-coded values on linker, set them according to the max size
of the kernel image set by CONFIG_ESP32S3_KERNEL_IMAGE_SIZE. This
is done by making KIROM, UIROM, KDROM and UDROM dependent on the
kernel size value. Also, override CONFIG_NUTTX_USERSPACE config
according to CONFIG_ESP32S3_KERNEL_IMAGE_SIZE by using a custom
PREBUILD definition.
board/esp32s3/common is for common board driver. It should not
include a header file from specific board. so remove include
of esp32s3-devkit.h from some of the common driver source
Whenever a SPI flash operation is going to take place, it's
necessary to disable both the instruction and data cache. In order
to avoid the other CPU (if SMP is enabled) to retrieve data from
the SPI flash, it needs to be paused until the current SPI flash
operation finishes. All the code that "pauses" the other CPU (in
fact, the CPU spins until `up_cpu_resume` is called) needs to run
from the instruction RAM.
This config also prevents crashes due to the commit 6be363f, which
fix a race condition in multi-threaded write/read of the serial
driver, but increases stack size.
Instead of using Espressif's emulated NVS to save Wi-Fi data, use
`wapi`s wireless configure initialization mechanism for saving
Wi-Fi data. It 1) avoids creating a specific storage partition
just to save Wi-Fi data (ESP32-S3's storage partition is used
instead); 2) avoids initialization problems of the emulated NVS
when SMP is enabled (the Wi-Fi driver tries to initialize it before
the actual partition is initialized); and 3) enables reconnecting
using `wapi reconnect` command and connect the device automatically
on bringup if `CONFIG_NETUTILS_NETINIT` is selected.
While using NVS-like storage of the Wi-Fi driver, an error was
thrown while trying to access a file whose name was longer than
the mounted SPIFFS `CONFIG_SPIFFS_NAME_MAX`.
1) Wi-Fi driver libs from Espressif ESP-IDF release/v5.0;
2) Station mode only;
3) WPA2-PSK and WPA3-SAE enabled;
Not yet supported (WIP):
- SoftAP mode;
- 802.11k, 802.11v and 802.11R;
- Power Save mode;
- BLE Coexistance;
MCUboot support is no longer behind EXPERIMENTAL for the following
chips:
- ESP32
- ESP32-S2
- ESP32-S3
- ESP32-C3
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
In order to turn longjmp context-switch safe, it's necessary
to disable interrupts before modifying windowbase and windowstart.
Otherwise, after a context switch, windowstart and windowbase
would be different, leading to a wrongly set windowstart bit due to
longjmp writing it based on the windowbase before the context switch.
This corrupts the registers at the next window overflow reaching
that wrongly set bit.
*Background:*
This PR is related to an issue first observed on ESP-IDF
https://github.com/espressif/esp-idf/issues/5229 and it was, then,
checked on NuttX using a test application.
*The test application:*
To check if the problem affects ESP32, ESP32-S2 and ESP32-S3 on
NuttX, it was created an application based on:
https://en.cppreference.com/w/c/program/longjmp
The application creates 16 tasks (`#define NUMBER_OF_TASKS 16`)
that implements the following daemon:
```
static int setjmp_longjmp_daemon(int argc, char *argv[])
{
for (int i = 0; i < NUMBER_OF_TASKS * 2; i++)
{
jmp_buf env;
volatile int count = 0;
if (setjmp(env) != UINT16_MAX)
{
foo(&env, ++count);
}
}
sem_post(&g_sem);
return EXIT_SUCCESS;
}
```
The main function also initializes a semaphore to avoid application
exiting before tasks return successfully:
```
sem_init(&g_sem, 0, -NUMBER_OF_TASKS);
```
Finally, the round-robin interval was lowered to 1ms to raise the
chances of the longjmp being interrupted by a context switch
(`CONFIG_RR_INTERVAL=1).
This setup was able to reproduce the problem prior to this patch
being applied.
This change syncs the NuttX application image IRAM upper limit to the
start of the IRAM region used by the IDF 2nd stage bootloader.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
