NuttX: STM32F407VG has only one DAC
NDAC=2 causes compilation error when trying to use e.g. STM32_DAC1_CR macro.
Approved-by: GregoryN <gnutt@nuttx.org>
imxrt:Clock config fixes and board.h sets sources and divisors
* imxrt:clockconfig bug fix & Board config set clocks
Fixed logic that was not clearing bits as ~ was
mising in &= mask operations.
Use valuse from the board.h file so set the Mux that
selects the clock sources.
Use board defined PODF values to select clock.
Only configure USDHC2 clocks when board defines clocks.
* imxrt1050-evk:Board setting used to set LSPI and USDHC Clocks
Approved-by: GregoryN <gnutt@nuttx.org>
This change is needed specifically for the case where a bootloader sets the SPE bit before starting NuttX. In that case, the test in the SPI driver is bogus. This change fixes that by assuring that NuttX has booted and initialized at least once (whether or not SPE is set) before the driver starts refusing to initialize.
arch/arm/stm32*: Don't rely on SPI_CR1_SPE to determine if peripheral has been initialized yet.
Approved-by: GregoryN <gnutt@nuttx.org>
Fixes Kconfig options to include all STM32F20XX processors, not just STM32F207
* arch/arm/src/stm32: Fixes Kconfig options to include all STM32F20XX processors, not just STM32F207
* arch/arm/src/stm32: Removes redundant STM32_STM32F429 depends from Kconfig. STM32F4XXX already does this
Approved-by: GregoryN <gnutt@nuttx.org>
In addition to the problems that were previously identified there were a few other bits and pieces outstanding;
* Timing was dependent on CPU speed rather than absolute time
* End of transfer handling was a bit mixed up
* It's possible for data to still be in the FIFO (i.e. not have reached
the card) when a next write is requested, so we need to wait for that to
complete
* Interrupt Status could be carried over from one transfer episode to the
next, corrupting progress
* Multi-descriptor DMA writing simply wasn't implemented, but there were no
indications ... it just failed silently
Master imxrt
* imxrt:Fix typos bit# and names
* imxrt:wdog Registers are 16 Bits
* imxrt:wdog Update has to be within 255 clocks of unlock
* imxrt:clockconfig Fix comments
* imxrt1050-evk:board.h Fix comments
* imxrt:imxrt_ccm.h Define Mux Selects for board.h use
* imxrt:clockconfig Allow better control from board.h
1) Allows a board config clock setting to be defined
in terms of the /n values shown in Figure 18-2.
Clock Tree of the i.MX RT1050 Processor Reference
Manual, Rev. 1, 03/2018
2) Allows the clock multipelx selection to be made in
The board config.
* imxrt1050-evk:Define board clocking based on divisor and muxes
Approved-by: GregoryN <gnutt@nuttx.org>
* Clocks were wrongly configured - way too fast because there is no primary divider on LPC4330
This is fixed by means of changing the definitions in the board.h file. I've edited the one for the lpc4330-xplorer board because I'm actually working with Versiboard and don't want to contribute that config just yet while I've still got the drains up on it.
* The LPC43_SDMMC_DELAY register was not being set
I suspect, in the 'real world', it's possible to get away without setting this, but I've added a register definition, default value and register access macros into arch/arm/src/lpc43xx/chip/lpc43_scu.h and then used them in arch/arm/src/lpc43xx/lpc43_sdmmc.c.
* The LPC43_SDMMC_BLKSIZ and LPC43_SDMMC_BYTECNT registers had the wrong values.
The management have already implemented a rather nice block level interface for the stm32 so I've just re-used that to write to these registers as required. I'm slightly nervous that accessing the configuration registers (SCR being the prime example) which has a much smaller block size may not be being done in the right way but it does seem to work correctly, so let's assume it's all OK until someone tells me otherwise.
These fixes have been tested with DMA-based read/write on a LPC4330. Speed via nsh is pretty low but I'm assuming that's just a buffering/implementation issue for now.
Improvements in STM32 PWM low level driver
stm32_pwm: remove some impossible PWM configurations
stm32_pwm: support for complementary outputs
stm32_pwm: deadtime configuration
stm32_pwm: output polarity and IDLE state configuration
nucleo-f302r8: pwm support
stm32f429i-disco: pwm support
configs: update some configurations according to changes in STM32 PWM driver
Approved-by: GregoryN <gnutt@nuttx.org>
(1) Now the Ethernet is completely re-initialized when an error occurs by means of taking the interface down and back up but the PHY is _not_ renegotiated for that case because that is very time consuming and an error in the Ethernet is no reflection on the state of the PHY anyway.
(2) Explicitly sets the expected PHY address to zero (this could be moved into the config) rather than searching for it which takes ages, and it's zero anyway for this board (that's the broadcast address, and anything that cannot respond on that has multiple PHYs, so that would be a new board).
(3) Allows for the renegotiation of the PHY to be optional when a reset is needed. If a non-renegotiated reset doesn't result in good comms to the PHY then it'll automatically be escalated to a renegotiated one.
(4) Only performs a reset for errors that need it (the CRITICAL_ERROR define). The list of errors that need reset are somewhat arbitrarily chosen based on my prejudices and might need to be revisited, but certainly the jabber errors don't need reset, the partial packet is thrown away by the layer above anyway.
(5) Re-loads the multicast table on reset.
(6) Adds a bit more logging into the imxrt Ethernet module.
arch/arm/src/lc823450: Fix up_allocate_heap() in lc823450_allocateheap2.c
For lc823450, heap area in flat build mode must start just after
_eronly. Because bss/data area is allocated in lower address than
text area in SRAM. See ld.scripts for details. Also, this change
removes unsed up_allocateheap.c
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Approved-by: GregoryN <gnutt@nuttx.org>
Pull request for mtd/progmem refactoring.
* mtd/progmem: change up_progmem_npages to up_progmem_neraseblocks
page is a unit for read/write operation.
eraseblock is a unit for erase operation.
up_progmem_npages is a little bit confusing because it returns number of
erase blocks in flash memory. This patch changes up_progmem_npages to
up_progmem_neraseblocks. There is no logical change.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: up_progmem_erasesize.
Change argument name to be more readable.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: up_progmem_eraseblock
Change up_progmem_erasepage to up_progmem_eraseblock.
eraseblock is more readable name than erasepage.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* mtd/progmem: change up_progmem_eraseblock's return value.
up_progmem_eraseblock erase a block. so it's better to return the erase block
size than page size.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/cortex-r : fix wrong cp15_flash_dcache.
change mcrne to mcr for unconditional dcache.
Signed-off-by: sungduk.cho <sungduk.cho@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
kinetis:i2c On faild reset re-init i2c and clocking
If a reset fails, we still must reinitializes the
i2c block so that subsequent transfers will not
cause a hardfault due to the clock being off.
If that transfer fails it can try to reset
again.
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/lpc43xx: Fix ethernet TX_EN pin definitions
TX_EN on LPC43xx can be routed via P0.1 and PC.4 in both
MII and RMII mode.
Before, P0.1 was hardcoded for MII and PC.4 was hardcoded for RMII.
Also, the definitions used inconsistent naming (TXEN vs. TX_EN).
Approved-by: GregoryN <gnutt@nuttx.org>
arch/arm/src/lpc43xx: Make WWDT usable again
LPC43xx WWDT driver was not updated when irq_dispatch grew an argument
flag in b3222bbc8a.
Also fixes two typos and a naming inconsistency (WWDT vs. WWDG).
Approved-by: GregoryN <gnutt@nuttx.org>
Pull request for cortex-r4 codes
* arm/armv7-r: Add general interrupt controller.
This is based on armv7-a gic controller code.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/armv7-r: add invalidate dcache in arm_head.S
Adding invalidate dcache as a comment in arm_head.S.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/armv7-r: Fix some wrong configuration of program status register.
PSR_E_BIT bit should be set for big endian system.
PSR_A_BIT bis is set automatically as arm cortex-r4 reference manual 3.7.4.
So we don't need to set this bit.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* arm/armv7-r: Fix some wrong MPU register definition.
Change MPU_RBAR_ADDR_MASK and MPU_RACR_TEX_SHIFT mask as
arm cortex-r4 reference manual.
Region Base Address Register 0-4 bits are reserved.
MPU Region Access control register type 3-5 bits.
Signed-off-by: EunBong Song <eunb.song@samsung.com>
* driver/mtd: fix compilation error.
This commit fixes below compilation errors.
CC: mtd/smart.c
mtd/smart.c:182:22: error: 'gWearBitToLevelMap4' defined but not used [-Werror=unused-const-variable=]
static const uint8_t gWearBitToLevelMap4[] =
^~~~~~~~~~~~~~~~~~~
mtd/smart.c:170:22: error: 'gWearLevelToBitMap4' defined but not used [-Werror=unused-const-variable=]
static const uint8_t gWearLevelToBitMap4[] =
^~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[1]: *** [smart.o] Error 1
Signed-off-by: Junyeon LEE <junyeon2.lee@samsung.com>
Approved-by: GregoryN <gnutt@nuttx.org>
drivers/serial/uart_16550.c: Add a configuration, analogous to the STM32 configuration option, to suppress the NuttX standard re-ordering for /dev/ttySN for special case of the 16550 UART.
config/serial: UART 16550: Add CONFIG_SERIAL_UART_ARCH_MMIO option so the a memory mapped device doesn't need to provide uart_getreg() and uart_putreg() implementations.
u16550_txempty() should check UART_LSR_TEMT to avoid some data left in the transmit FIFO
kinetis:i2c ensure timeout on bus error
The code had a dead wait on I2C_S_BUSY. Noise on the
bus would cause the driver to hang.
Add timeout on invalid states of I2C_S_BUSY to allow
the upper layers do deal with restart or abort.
Approved-by: GregoryN <gnutt@nuttx.org>
