Sync driver interfaces, also fixes the handling of special pin value for
esp32s2_gpio_matrix_in and esp32s2_gpio_matrix_out functions
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
SAMA5D2 and SAMA5D4 does not support external reset.
Some SAMA5 board's Kconfig contain item SAMA5_SYSTEMRESET, but it is better in arch/arm/src/Kconfig.
In order to support multiple LCD instances per board, add a pointer from
lcd_planeinfo_s to the lcd_dev_s which it belongs to. Also enhance the
putrun, getrun, putarea and getarea methods to pass through the
lcd_dev_s pointer to the respective device driver.
Port all LCD device drivers to this lcd_planeinfo_s extension.
Enhance SSD1306 driver to support multiple LCDs.
Signed-off-by: Michael Jung <michael.jung@secore.ly>
Sync some of the AXI configuration and DDR training parameters with the manufacturer's
defaults.
The TIP_CFG parameter correction helps with DDR training failures on some individual boards
The AXI end address values fix early random crash in power-on boot on some individual boards
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Update PLL configuration parameters to match the values provided
by the vendor.
Also remove extra call to mpfs_pll_config() as it's already called
at mpfs_clockconfig().
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This patch adds working integration of progmem FLASH. User can partition
internal FLASH memory to up to 4 partitions and use any combination of
raw, nxffs, smartfs and mtd_config filesystems (unless there are other
limitations like nxffs supports only single instance).
Support for dual CPU is added to Kconfig to not overwrite CPU2 program code.
Code guards user to not allocate more memory than there is on FLASH, and
warns user if not all FLASH memory is used. Errors will be printed when
user tries to initialize two instances of nxffs or mtd_config filesystems.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
This patch adds to the nucleo-wl55jc previously implemented EXTI support.
Button support with nuttx's button driver is added.
I've written small example to show how to use GPIO EXTI. B3 button can be
used (selectable via Kconfig) to toggle Red LED.
I've added new defconfig for demo purposes. I've included there config
and enabled example programs that are meant to demonstrate functions of
the board and does not really have a place in real world project. Like
Red LED can be toggled with B3 button, or LED example that flashes LEDS,
or button example to show which button has been pressed.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
--
v1 -> v2:
Suggested by: Petro Karashchenko
- Change (1 << 0) to (1 << BUTTON1_BIT (and similar)
v2 -> v3:
- Fix invalid BUTTON3_BIT value
v3 -> v4:
Suggested by: Petro Karashchenko
- Change 0/1 to false/true
This provides USB composite (CDC/ACM and Mass Storage) support
for mpfs board. In addition, a number of USB fixes are included:
- Support for Setup Out packets
- Proper support for larger than packet size writes
- Finishing setup packets properly
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This patch includes bare minimum support for nucleo-wl55jc board.
It compiles and nsh shell is working properly on virtual com port
over USB. 3 onboard leds with userled driver are working.
Signed-off-by: Michał Łyszczek <michal.lyszczek@bofc.pl>
arch/x86/Kconfig:28:warning: choice value used outside its choice group
arch/x86/Kconfig:29:warning: defaults for choice values not supported
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
The driver is provided by Spresense SDK
ISX019 has the DOL-HDR feature, which combines images with different exposure so that
both bright and dark data of high-contrast subject can be viewed at the same time.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Change pin initialization timing for camera from board power on to camera device
power on for the following purposes.
- avoid unnecessary power consumption
- Make the corresponding pins available for other uses when camera is not in use
RF and system timer interrupt are used for ble.
tlsr82_flash.c:
1. BLE will loss packets during flash operation beacause the interrupt
is disabled and the operation take too long (especially erasing,
about 100ms), so allow RF and system timer interrupt during flash
operation;
2. Add sched_lock()/sched_unlock() to avoid the task switch in ble and
system timer interrupt;
flash_boot_ble.ld:
3. Because of 1, the code executes in RF and system timer interrupt
must be in ram to avoid bus error. The sem_post() will be called and
const variable g_tasklisttable will be accessed in RF and system
timer interrupt handler;
4. To improve the performance, copy some frequently called function to
ram as well, such as: sem_take(), sched_lock(), sched_unlock(),
some lib functions, some zephyr ble functions and some tinycrypt
functions;
5. The RF and system timer interrupt handler will call some libgcc
functions, so copy all the libgcc functions to ram exclude _divdi3.o,
_udivdi3.o and _umoddi3.o;
tlsr82_serial.c
6. Make up_putc() be thread safe, add enter/leave_critical_section() in
function uart_send_byte();
tc32_doirq.c
7. Increase the RF and system timer interrupt response priority;
Signed-off-by: wangbowen6 <wangbowen6@xiaomi.com>
