/**************************************************************************** * drivers/mmcsd/mmcsd_sdio.c * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #if defined (CONFIG_MMCSD) && defined (CONFIG_MMCSD_SDIO) #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "mmcsd.h" #include "mmcsd_sdio.h" /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* The maximum number of references on the driver (because a uint8_t is used. * Use a larger type if more references are needed. */ #define MAX_CREFS 0xff /* Timing (all in units of microseconds) */ #define MMCSD_POWERUP_DELAY ((useconds_t)250) /* 74 clock cycles @ 400KHz = 185uS */ #define MMCSD_IDLE_DELAY ((useconds_t)100000) /* Short delay to allow change to IDLE state */ #define MMCSD_DSR_DELAY ((useconds_t)100000) /* Time to wait after setting DSR */ #define MMCSD_CLK_DELAY ((useconds_t)5000) /* Delay after changing clock speeds */ /* Data delays (all in units of milliseconds). * * For MMC & SD V1.x, these should be based on Nac = TAAC + NSAC; The * maximum value of TAAC is 80MS and the maximum value of NSAC is 25.5K * clock cycle. For SD V2.x, a fixed delay of 100MS is recommend which is * pretty close to the worst case SD V1.x Nac. Here we just use 100MS * delay for all data transfers. */ #define MMCSD_SCR_DATADELAY (100) /* Wait up to 100MS to get SCR */ #define MMCSD_BLOCK_RDATADELAY (100) /* Wait up to 100MS to get one data block */ /* Wait timeout to write one data block */ #define MMCSD_BLOCK_WDATADELAY CONFIG_MMCSD_BLOCK_WDATADELAY #define IS_EMPTY(priv) (priv->type == MMCSD_CARDTYPE_UNKNOWN) #if CONFIG_MMCSD_MULTIBLOCK_LIMIT == 0 # define MMCSD_MULTIBLOCK_LIMIT SSIZE_MAX #else # define MMCSD_MULTIBLOCK_LIMIT CONFIG_MMCSD_MULTIBLOCK_LIMIT #endif #define MMCSD_CAPACITY(b, s) ((s) >= 10 ? (b) << ((s) - 10) : (b) >> (10 - (s))) #ifdef CONFIG_BOARD_COREDUMP_BLKDEV # define MMCSD_USLEEP(usec) \ do \ { \ if (up_interrupt_context()) \ { \ up_udelay(usec); \ } \ else \ { \ nxsig_usleep(usec); \ } \ } while (0) #else # define MMCSD_USLEEP(usec) nxsig_usleep(usec) #endif /**************************************************************************** * Private Types ****************************************************************************/ /**************************************************************************** * Private Function Prototypes ****************************************************************************/ /* Misc Helpers *************************************************************/ static int mmcsd_lock(FAR struct mmcsd_state_s *priv); static void mmcsd_unlock(FAR struct mmcsd_state_s *priv); /* Command/response helpers *************************************************/ static int mmcsd_sendcmdpoll(FAR struct mmcsd_state_s *priv, uint32_t cmd, uint32_t arg); static int mmcsd_recv_r1(FAR struct mmcsd_state_s *priv, uint32_t cmd); static int mmcsd_recv_r6(FAR struct mmcsd_state_s *priv, uint32_t cmd); static int mmcsd_get_scr(FAR struct mmcsd_state_s *priv, uint32_t scr[2]); static void mmcsd_decode_csd(FAR struct mmcsd_state_s *priv, uint32_t csd[4]); #ifdef CONFIG_DEBUG_FS_INFO static void mmcsd_decode_cid(FAR struct mmcsd_state_s *priv, uint32_t cid[4]); #else # define mmcsd_decode_cid(priv,cid) #endif static void mmcsd_decode_scr(FAR struct mmcsd_state_s *priv, uint32_t scr[2]); static int mmcsd_get_r1(FAR struct mmcsd_state_s *priv, FAR uint32_t *r1); static int mmcsd_verifystate(FAR struct mmcsd_state_s *priv, uint32_t status); /* Transfer helpers *********************************************************/ static bool mmcsd_wrprotected(FAR struct mmcsd_state_s *priv); static int mmcsd_eventwait(FAR struct mmcsd_state_s *priv, sdio_eventset_t failevents); static int mmcsd_transferready(FAR struct mmcsd_state_s *priv); #if MMCSD_MULTIBLOCK_LIMIT != 1 static int mmcsd_stoptransmission(FAR struct mmcsd_state_s *priv); #endif static int mmcsd_setblocklen(FAR struct mmcsd_state_s *priv, uint32_t blocklen); #if MMCSD_MULTIBLOCK_LIMIT != 1 static int mmcsd_setblockcount(FAR struct mmcsd_state_s *priv, uint32_t nblocks); #endif static ssize_t mmcsd_readsingle(FAR struct mmcsd_state_s *priv, FAR uint8_t *buffer, off_t startblock); #if MMCSD_MULTIBLOCK_LIMIT != 1 static ssize_t mmcsd_readmultiple(FAR struct mmcsd_state_s *priv, FAR uint8_t *buffer, off_t startblock, size_t nblocks); #endif static ssize_t mmcsd_writesingle(FAR struct mmcsd_state_s *priv, FAR const uint8_t *buffer, off_t startblock); #if MMCSD_MULTIBLOCK_LIMIT != 1 static ssize_t mmcsd_writemultiple(FAR struct mmcsd_state_s *priv, FAR const uint8_t *buffer, off_t startblock, size_t nblocks); #endif /* Block driver methods *****************************************************/ static int mmcsd_open(FAR struct inode *inode); static int mmcsd_close(FAR struct inode *inode); static ssize_t mmcsd_read(FAR struct inode *inode, FAR unsigned char *buffer, blkcnt_t startsector, unsigned int nsectors); static ssize_t mmcsd_write(FAR struct inode *inode, FAR const unsigned char *buffer, blkcnt_t startsector, unsigned int nsectors); static int mmcsd_geometry(FAR struct inode *inode, FAR struct geometry *geometry); static int mmcsd_ioctl(FAR struct inode *inode, int cmd, unsigned long arg); /* Initialization/uninitialization/reset ************************************/ static void mmcsd_mediachange(FAR void *arg); static int mmcsd_widebus(FAR struct mmcsd_state_s *priv); #ifdef CONFIG_MMCSD_MMCSUPPORT static int mmcsd_mmcinitialize(FAR struct mmcsd_state_s *priv); static int mmcsd_read_csd(FAR struct mmcsd_state_s *priv, FAR uint8_t *data); #endif static int mmcsd_sdinitialize(FAR struct mmcsd_state_s *priv); static int mmcsd_cardidentify(FAR struct mmcsd_state_s *priv); static int mmcsd_probe(FAR struct mmcsd_state_s *priv); static int mmcsd_removed(FAR struct mmcsd_state_s *priv); static int mmcsd_hwinitialize(FAR struct mmcsd_state_s *priv); static void mmcsd_hwuninitialize(FAR struct mmcsd_state_s *priv); #ifdef CONFIG_MMCSD_IOCSUPPORT static int mmcsd_iocmd(FAR struct mmcsd_state_s *priv, FAR struct mmc_ioc_cmd *ic_ptr); static int mmcsd_multi_iocmd(FAR struct mmcsd_state_s *priv, FAR struct mmc_ioc_multi_cmd *imc_ptr); #endif /**************************************************************************** * Private Data ****************************************************************************/ static const struct block_operations g_bops = { mmcsd_open, /* open */ mmcsd_close, /* close */ mmcsd_read, /* read */ mmcsd_write, /* write */ mmcsd_geometry, /* geometry */ mmcsd_ioctl /* ioctl */ }; /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Misc Helpers ****************************************************************************/ static int mmcsd_lock(FAR struct mmcsd_state_s *priv) { int ret; /* Take the lock, giving exclusive access to the driver (perhaps * waiting) */ if (!up_interrupt_context() && !sched_idletask()) { ret = nxmutex_lock(&priv->lock); if (ret < 0) { return ret; } /* Lock the bus if mutually exclusive access to the * SDIO bus is required on this platform. */ #ifdef CONFIG_SDIO_MUXBUS SDIO_LOCK(priv->dev, TRUE); #endif } else { ret = OK; } return ret; } static void mmcsd_unlock(FAR struct mmcsd_state_s *priv) { if (!up_interrupt_context() && !sched_idletask()) { /* Release the SDIO bus lock, then the MMC/SD driver mutex in the * opposite order that they were taken to assure that no deadlock * conditions will arise. */ #ifdef CONFIG_SDIO_MUXBUS SDIO_LOCK(priv->dev, FALSE); #endif nxmutex_unlock(&priv->lock); } } /**************************************************************************** * Command/Response Helpers ****************************************************************************/ /**************************************************************************** * Name: mmcsd_sendcmdpoll * * Description: * Send a command and poll-wait for the response. * ****************************************************************************/ static int mmcsd_sendcmdpoll(FAR struct mmcsd_state_s *priv, uint32_t cmd, uint32_t arg) { int ret; /* Send the command */ ret = SDIO_SENDCMD(priv->dev, cmd, arg); if (ret == OK) { /* Then poll-wait until the response is available */ ret = SDIO_WAITRESPONSE(priv->dev, cmd); if (ret != OK) { ferr("ERROR: Wait for response to cmd: %08" PRIx32 " failed: %d\n", cmd, ret); } } return ret; } /**************************************************************************** * Name: mmcsd_sendcmd4 * * Description: * Set the Driver Stage Register (DSR) if (1) a CONFIG_MMCSD_DSR has been * provided and (2) the card supports a DSR register. If no DSR value * the card default value (0x0404) will be used. * ****************************************************************************/ static inline int mmcsd_sendcmd4(FAR struct mmcsd_state_s *priv) { int ret = OK; #ifdef CONFIG_MMCSD_DSR /* The dsr_imp bit from the CSD will tell us if the card supports setting * the DSR via CMD4 or not. */ if (priv->dsrimp != false) { finfo("Card supports DSR - send DSR.\n"); /* CMD4 = SET_DSR will set the cards DSR register. The DSR and CMD4 * support are optional. However, since this is a broadcast command * with no response (like CMD0), we will never know if the DSR was * set correctly or not */ mmcsd_sendcmdpoll(priv, MMCSD_CMD4, CONFIG_MMCSD_DSR << 16); MMCSD_USLEEP(MMCSD_DSR_DELAY); /* Send it again to have more confidence */ mmcsd_sendcmdpoll(priv, MMCSD_CMD4, CONFIG_MMCSD_DSR << 16); MMCSD_USLEEP(MMCSD_DSR_DELAY); } else { finfo("Card does not support DSR.\n"); } #endif return ret; } /**************************************************************************** * Name: mmcsd_recv_r1 * * Description: * Receive R1 response and check for errors. * ****************************************************************************/ static int mmcsd_recv_r1(FAR struct mmcsd_state_s *priv, uint32_t cmd) { uint32_t r1; int ret; /* Get the R1 response from the hardware */ ret = SDIO_RECVR1(priv->dev, cmd, &r1); if (ret == OK) { /* Check if R1 reports an error */ if ((r1 & MMCSD_R1_ERRORMASK) != 0) { /* Card locked is considered an error. Save the card locked * indication for later use. */ ferr("ERROR: R1=%08" PRIx32 "\n", r1); priv->locked = ((r1 & MMCSD_R1_CARDISLOCKED) != 0); ret = -EIO; } } return ret; } /**************************************************************************** * Name: mmcsd_recv_r6 * * Description: * Receive R6 response and check for errors. On success, priv->rca is set * to the received RCA * ****************************************************************************/ static int mmcsd_recv_r6(FAR struct mmcsd_state_s *priv, uint32_t cmd) { uint32_t r6 = 0; int ret; /* R6 Published RCA Response (48-bit, SD card only) * 47 0 Start bit * 46 0 Transmission bit (0=from card) * 45:40 bit5 - bit0 Command index (0-63) * 39:8 bit31 - bit0 32-bit Argument Field, consisting of: * [31:16] New published RCA of card * [15:0] Card status bits {23,22,19,12:0} * 7:1 bit6 - bit0 CRC7 * 0 1 End bit * * Get the R6 response from the hardware */ ret = SDIO_RECVR6(priv->dev, cmd, &r6); if (ret == OK) { /* Check if R6 reports an error */ if ((r6 & MMCSD_R6_ERRORMASK) == 0) { /* No, save the RCA and return success */ priv->rca = (uint16_t)(r6 >> 16); return OK; } /* Otherwise, return an I/O failure */ ret = -EIO; } ferr("ERROR: Failed to get RCA. R6=%08" PRIx32 ": %d\n", r6, ret); return ret; } /**************************************************************************** * Name: mmcsd_get_scr * * Description: * Obtain the SD card's Configuration Register (SCR) * * Returned Value: * OK on success; a negated ernno on failure. * ****************************************************************************/ static int mmcsd_get_scr(FAR struct mmcsd_state_s *priv, uint32_t scr[2]) { int ret; /* Set Block Size To 8 Bytes */ ret = mmcsd_setblocklen(priv, 8); if (ret != OK) { ferr("ERROR: mmcsd_setblocklen failed: %d\n", ret); return ret; } /* Setup up to receive data with interrupt mode */ SDIO_BLOCKSETUP(priv->dev, 8, 1); SDIO_RECVSETUP(priv->dev, (FAR uint8_t *)scr, 8); SDIO_WAITENABLE(priv->dev, SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR, MMCSD_SCR_DATADELAY); /* Send CMD55 APP_CMD with argument as card's RCA */ mmcsd_sendcmdpoll(priv, SD_CMD55, (uint32_t)priv->rca << 16); ret = mmcsd_recv_r1(priv, SD_CMD55); if (ret != OK) { ferr("ERROR: RECVR1 for CMD55 failed: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } /* Send ACMD51 SD_APP_SEND_SCR with argument as 0 to start data receipt */ mmcsd_sendcmdpoll(priv, SD_ACMD51, 0); ret = mmcsd_recv_r1(priv, SD_ACMD51); if (ret != OK) { ferr("ERROR: RECVR1 for ACMD51 failed: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } /* Wait for data to be transferred */ ret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (ret != OK) { ferr("ERROR: mmcsd_eventwait for READ DATA failed: %d\n", ret); } return ret; } /**************************************************************************** * Name: mmcsd_decode_csd * * Description: * Decode and extract necessary information from the CSD. If debug is * enabled, then decode and show the full contents of the CSD. * * Returned Value: * OK on success; a negated ernno on failure. On success, the following * values will be set in the driver state structure: * * priv->dsrimp true: card supports CMD4/DSR setting (from CSD) * priv->wrprotect true: card is write protected (from CSD) * priv->blocksize Read block length (== block size) * priv->nblocks Number of blocks * ****************************************************************************/ static void mmcsd_decode_csd(FAR struct mmcsd_state_s *priv, uint32_t csd[4]) { #ifdef CONFIG_DEBUG_FS_INFO struct mmcsd_csd_s decoded; #endif unsigned int readbllen; bool permwriteprotect; bool tmpwriteprotect; /* Word 1: Bits 127-96: * * CSD_STRUCTURE 127:126 CSD structure * SPEC_VERS 125:122 (MMC) Spec version * TAAC 119:112 Data read access-time-1 * TIME_VALUE 6:3 Time mantissa * TIME_UNIT 2:0 Time exponent * NSAC 111:104 Data read access-time-2 in CLK * cycle(NSAC*100) * TRAN_SPEED 103:96 Max. data transfer rate * TIME_VALUE 6:3 Rate exponent * TRANSFER_RATE_UNIT 2:0 Rate mantissa */ #ifdef CONFIG_DEBUG_FS_INFO memset(&decoded, 0, sizeof(struct mmcsd_csd_s)); decoded.csdstructure = csd[0] >> 30; decoded.mmcspecvers = (csd[0] >> 26) & 0x0f; decoded.taac.timevalue = (csd[0] >> 19) & 0x0f; decoded.taac.timeunit = (csd[0] >> 16) & 7; decoded.nsac = (csd[0] >> 8) & 0xff; decoded.transpeed.timevalue = (csd[0] >> 3) & 0x0f; decoded.transpeed.transferrateunit = csd[0] & 7; #endif /* Word 2: Bits 64:95 * CCC 95:84 Card command classes * READ_BL_LEN 83:80 Max. read data block length * READ_BL_PARTIAL 79:79 Partial blocks for read allowed * WRITE_BLK_MISALIGN 78:78 Write block misalignment * READ_BLK_MISALIGN 77:77 Read block misalignment * DSR_IMP 76:76 DSR implemented * Byte addressed SD and MMC: * C_SIZE 73:62 Device size * Block addressed SD: * 75:70 (reserved) * C_SIZE 48:69 Device size */ priv->dsrimp = (csd[1] >> 12) & 1; readbllen = (csd[1] >> 16) & 0x0f; #ifdef CONFIG_DEBUG_FS_INFO decoded.ccc = (csd[1] >> 20) & 0x0fff; decoded.readbllen = (csd[1] >> 16) & 0x0f; decoded.readblpartial = (csd[1] >> 15) & 1; decoded.writeblkmisalign = (csd[1] >> 14) & 1; decoded.readblkmisalign = (csd[1] >> 13) & 1; decoded.dsrimp = priv->dsrimp; #endif /* Word 3: Bits 32-63 * * Byte addressed SD: * C_SIZE 73:62 Device size * VDD_R_CURR_MIN 61:59 Max. read current at Vcc min * VDD_R_CURR_MAX 58:56 Max. read current at Vcc max * VDD_W_CURR_MIN 55:53 Max. write current at Vcc min * VDD_W_CURR_MAX 52:50 Max. write current at Vcc max * C_SIZE_MULT 49:47 Device size multiplier * SD_ER_BLK_EN 46:46 Erase single block enable (SD only) * SD_SECTOR_SIZE 45:39 Erase sector size * SD_WP_GRP_SIZE 38:32 Write protect group size * Block addressed SD: * 75:70 (reserved) * C_SIZE 48:69 Device size * 47:47 (reserved) * SD_ER_BLK_EN 46:46 Erase single block enable (SD only) * SD_SECTOR_SIZE 45:39 Erase sector size * SD_WP_GRP_SIZE 38:32 Write protect group size * MMC: * C_SIZE 73:62 Device size * VDD_R_CURR_MIN 61:59 Max. read current at Vcc min * VDD_R_CURR_MAX 58:56 Max. read current at Vcc max * VDD_W_CURR_MIN 55:53 Max. write current at Vcc min * VDD_W_CURR_MAX 52:50 Max. write current at Vcc max * C_SIZE_MULT 49:47 Device size multiplier * MMC_SECTOR_SIZE 46:42 Erase sector size * MMC_ER_GRP_SIZE 41:37 Erase group size (MMC) * MMC_WP_GRP_SIZE 36:32 Write protect group size */ if (IS_BLOCK(priv->type)) { #ifdef CONFIG_MMCSD_MMCSUPPORT if (IS_MMC(priv->type)) { /* Block addressed MMC: * * C_SIZE: 73:64 from Word 2 and 63:62 from Word 3 */ /* If the card is MMC and it has Block addressing * then the correct number of blocks should already be * read from extended CSD register. */ #ifdef CONFIG_DEBUG_FS_INFO uint16_t csize = ((csd[1] & 0x03ff) << 2) | ((csd[2] >> 30) & 3); uint8_t csizemult = (csd[2] >> 15) & 7; #endif priv->blockshift = readbllen; priv->blocksize = (1 << readbllen); if (priv->blocksize > 512) { priv->blocksize = 512; priv->blockshift = 9; } #ifdef CONFIG_DEBUG_FS_INFO decoded.u.mmc.csize = csize; decoded.u.mmc.vddrcurrmin = (csd[2] >> 27) & 7; decoded.u.mmc.vddrcurrmax = (csd[2] >> 24) & 7; decoded.u.mmc.vddwcurrmin = (csd[2] >> 21) & 7; decoded.u.mmc.vddwcurrmax = (csd[2] >> 18) & 7; decoded.u.mmc.csizemult = csizemult; decoded.u.mmc.er.mmc22.sectorsize = (csd[2] >> 10) & 0x1f; decoded.u.mmc.er.mmc22.ergrpsize = (csd[2] >> 5) & 0x1f; decoded.u.mmc.mmcwpgrpsize = csd[2] & 0x1f; #endif } else #endif { /* Block addressed SD: * * C_SIZE: 69:64 from Word 2 and 63:48 from Word 3 * * 512 = (1 << 9) * 1024 = (1 << 10) * 512*1024 = (1 << 19) */ uint32_t csize = ((csd[1] & 0x3f) << 16) | (csd[2] >> 16); priv->blockshift = 9; priv->blocksize = 1 << 9; priv->nblocks = (csize + 1) << (19 - priv->blockshift); #ifdef CONFIG_DEBUG_FS_INFO decoded.u.sdblock.csize = csize; decoded.u.sdblock.sderblen = (csd[2] >> 14) & 1; decoded.u.sdblock.sdsectorsize = (csd[2] >> 7) & 0x7f; decoded.u.sdblock.sdwpgrpsize = csd[2] & 0x7f; #endif } } else { /* Byte addressed SD: * * C_SIZE: 73:64 from Word 2 and 63:62 from Word 3 */ uint16_t csize = ((csd[1] & 0x03ff) << 2) | ((csd[2] >> 30) & 3); uint8_t csizemult = (csd[2] >> 15) & 7; priv->nblocks = ((uint32_t)csize + 1) * (1 << (csizemult + 2)); priv->blockshift = readbllen; priv->blocksize = (1 << readbllen); /* Some devices, such as 2Gb devices, report blocksizes larger than * 512 bytes but still expect to be accessed with a 512 byte blocksize. * * NOTE: A minor optimization would be to eliminated priv->blocksize * and priv->blockshift: Those values will be 512 and 9 in all cases * anyway. */ if (priv->blocksize > 512) { priv->nblocks <<= (priv->blockshift - 9); priv->blocksize = 512; priv->blockshift = 9; } #ifdef CONFIG_DEBUG_FS_INFO if (IS_SD(priv->type)) { decoded.u.sdbyte.csize = csize; decoded.u.sdbyte.vddrcurrmin = (csd[2] >> 27) & 7; decoded.u.sdbyte.vddrcurrmax = (csd[2] >> 24) & 7; decoded.u.sdbyte.vddwcurrmin = (csd[2] >> 21) & 7; decoded.u.sdbyte.vddwcurrmax = (csd[2] >> 18) & 7; decoded.u.sdbyte.csizemult = csizemult; decoded.u.sdbyte.sderblen = (csd[2] >> 14) & 1; decoded.u.sdbyte.sdsectorsize = (csd[2] >> 7) & 0x7f; decoded.u.sdbyte.sdwpgrpsize = csd[2] & 0x7f; } #ifdef CONFIG_MMCSD_MMCSUPPORT else if (IS_MMC(priv->type)) { decoded.u.mmc.csize = csize; decoded.u.mmc.vddrcurrmin = (csd[2] >> 27) & 7; decoded.u.mmc.vddrcurrmax = (csd[2] >> 24) & 7; decoded.u.mmc.vddwcurrmin = (csd[2] >> 21) & 7; decoded.u.mmc.vddwcurrmax = (csd[2] >> 18) & 7; decoded.u.mmc.csizemult = csizemult; decoded.u.mmc.er.mmc22.sectorsize = (csd[2] >> 10) & 0x1f; decoded.u.mmc.er.mmc22.ergrpsize = (csd[2] >> 5) & 0x1f; decoded.u.mmc.mmcwpgrpsize = csd[2] & 0x1f; } #endif #endif } /* Word 4: Bits 0-31 * WP_GRP_EN 31:31 Write protect group enable * MMC DFLT_ECC 30:29 Manufacturer default ECC (MMC only) * R2W_FACTOR 28:26 Write speed factor * WRITE_BL_LEN 25:22 Max. write data block length * WRITE_BL_PARTIAL 21:21 Partial blocks for write allowed * FILE_FORMAT_GROUP 15:15 File format group * COPY 14:14 Copy flag (OTP) * PERM_WRITE_PROTECT 13:13 Permanent write protection * TMP_WRITE_PROTECT 12:12 Temporary write protection * FILE_FORMAT 10:11 File format * ECC 9:8 ECC (MMC only) * CRC 7:1 CRC * Not used 0:0 */ permwriteprotect = (csd[3] >> 13) & 1; tmpwriteprotect = (csd[3] >> 12) & 1; priv->wrprotect = (permwriteprotect || tmpwriteprotect); #ifdef CONFIG_DEBUG_FS_INFO decoded.wpgrpen = csd[3] >> 31; decoded.mmcdfltecc = (csd[3] >> 29) & 3; decoded.r2wfactor = (csd[3] >> 26) & 7; decoded.writebllen = (csd[3] >> 22) & 0x0f; decoded.writeblpartial = (csd[3] >> 21) & 1; decoded.fileformatgrp = (csd[3] >> 15) & 1; decoded.copy = (csd[3] >> 14) & 1; decoded.permwriteprotect = permwriteprotect; decoded.tmpwriteprotect = tmpwriteprotect; decoded.fileformat = (csd[3] >> 10) & 3; decoded.mmcecc = (csd[3] >> 8) & 3; decoded.crc = (csd[3] >> 1) & 0x7f; finfo("CSD:\n"); finfo(" CSD_STRUCTURE: %d SPEC_VERS: %d (MMC)\n", decoded.csdstructure, decoded.mmcspecvers); finfo(" TAAC {TIME_UNIT: %d TIME_VALUE: %d} NSAC: %d\n", decoded.taac.timeunit, decoded.taac.timevalue, decoded.nsac); finfo(" TRAN_SPEED {TRANSFER_RATE_UNIT: %d TIME_VALUE: %d}\n", decoded.transpeed.transferrateunit, decoded.transpeed.timevalue); finfo(" CCC: %d\n", decoded.ccc); finfo(" READ_BL_LEN: %d READ_BL_PARTIAL: %d\n", decoded.readbllen, decoded.readblpartial); finfo(" WRITE_BLK_MISALIGN: %d READ_BLK_MISALIGN: %d\n", decoded.writeblkmisalign, decoded.readblkmisalign); finfo(" DSR_IMP: %d\n", decoded.dsrimp); if (IS_BLOCK(priv->type)) { #ifdef CONFIG_MMCSD_MMCSUPPORT if (IS_MMC(priv->type)) { finfo(" MMC Block Addressing:\n"); finfo(" C_SIZE: %d C_SIZE_MULT: %d\n", decoded.u.mmc.csize, decoded.u.mmc.csizemult); finfo(" VDD_R_CURR_MIN: %d VDD_R_CURR_MAX: %d\n", decoded.u.mmc.vddrcurrmin, decoded.u.mmc.vddrcurrmax); finfo(" VDD_W_CURR_MIN: %d VDD_W_CURR_MAX: %d\n", decoded.u.mmc.vddwcurrmin, decoded.u.mmc.vddwcurrmax); finfo(" MMC_SECTOR_SIZE: %d MMC_ER_GRP_SIZE: %d " "MMC_WP_GRP_SIZE: %d\n", decoded.u.mmc.er.mmc22.sectorsize, decoded.u.mmc.er.mmc22.ergrpsize, decoded.u.mmc.mmcwpgrpsize); } else #endif { finfo(" SD Block Addressing:\n"); finfo(" C_SIZE: %d SD_ER_BLK_EN: %d\n", decoded.u.sdblock.csize, decoded.u.sdblock.sderblen); finfo(" SD_SECTOR_SIZE: %d SD_WP_GRP_SIZE: %d\n", decoded.u.sdblock.sdsectorsize, decoded.u.sdblock.sdwpgrpsize); } } else if (IS_SD(priv->type)) { finfo(" SD Byte Addressing:\n"); finfo(" C_SIZE: %d C_SIZE_MULT: %d\n", decoded.u.sdbyte.csize, decoded.u.sdbyte.csizemult); finfo(" VDD_R_CURR_MIN: %d VDD_R_CURR_MAX: %d\n", decoded.u.sdbyte.vddrcurrmin, decoded.u.sdbyte.vddrcurrmax); finfo(" VDD_W_CURR_MIN: %d VDD_W_CURR_MAX: %d\n", decoded.u.sdbyte.vddwcurrmin, decoded.u.sdbyte.vddwcurrmax); finfo(" SD_ER_BLK_EN: %d SD_SECTOR_SIZE: %d (SD) " "SD_WP_GRP_SIZE: %d\n", decoded.u.sdbyte.sderblen, decoded.u.sdbyte.sdsectorsize, decoded.u.sdbyte.sdwpgrpsize); } #ifdef CONFIG_MMCSD_MMCSUPPORT else if (IS_MMC(priv->type)) { finfo(" MMC:\n"); finfo(" C_SIZE: %d C_SIZE_MULT: %d\n", decoded.u.mmc.csize, decoded.u.mmc.csizemult); finfo(" VDD_R_CURR_MIN: %d VDD_R_CURR_MAX: %d\n", decoded.u.mmc.vddrcurrmin, decoded.u.mmc.vddrcurrmax); finfo(" VDD_W_CURR_MIN: %d VDD_W_CURR_MAX: %d\n", decoded.u.mmc.vddwcurrmin, decoded.u.mmc.vddwcurrmax); finfo(" MMC_SECTOR_SIZE: %d MMC_ER_GRP_SIZE: %d " "MMC_WP_GRP_SIZE: %d\n", decoded.u.mmc.er.mmc22.sectorsize, decoded.u.mmc.er.mmc22.ergrpsize, decoded.u.mmc.mmcwpgrpsize); } #endif finfo(" WP_GRP_EN: %d MMC DFLT_ECC: %d (MMC) R2W_FACTOR: %d\n", decoded.wpgrpen, decoded.mmcdfltecc, decoded.r2wfactor); finfo(" WRITE_BL_LEN: %d WRITE_BL_PARTIAL: %d\n", decoded.writebllen, decoded.writeblpartial); finfo(" FILE_FORMAT_GROUP: %d COPY: %d\n", decoded.fileformatgrp, decoded.copy); finfo(" PERM_WRITE_PROTECT: %d TMP_WRITE_PROTECT: %d\n", decoded.permwriteprotect, decoded.tmpwriteprotect); finfo(" FILE_FORMAT: %d ECC: %d (MMC) CRC: %d\n", decoded.fileformat, decoded.mmcecc, decoded.crc); finfo("Capacity: %luKb, Block size: %db, nblocks: %d wrprotect: %d\n", (unsigned long)MMCSD_CAPACITY(priv->nblocks, priv->blockshift), priv->blocksize, priv->nblocks, priv->wrprotect); #endif } /**************************************************************************** * Name: mmcsd_decode_cid * * Description: * Show the contents of the Card Identification Data (CID) (for debug * purposes only) * ****************************************************************************/ #ifdef CONFIG_DEBUG_FS_INFO static void mmcsd_decode_cid(FAR struct mmcsd_state_s *priv, uint32_t cid[4]) { struct mmcsd_cid_s decoded; /* Word 1: Bits 127-96: * mid - 127-120 8-bit Manufacturer ID * cbx - 113-112 2-bit Device/BGA * oid - 111-104 8-bit OEM/Application ID (ascii) * pnm - 103-56 48-bit Product Name (ascii) + null terminator * pnm[0] 103:96 */ decoded.mid = cid[0] >> 24; decoded.cbx = (cid[0] >> 16) & 0x3; decoded.oid = (cid[0] >> 8) & 0xff; decoded.pnm[0] = cid[0] & 0xff; /* Word 2: Bits 64:95 * pnm - 103-56 48-bit Product Name (ascii) + null terminator * pnm[1] 95:88 * pnm[2] 87:80 * pnm[3] 79:72 * pnm[4] 71:64 */ decoded.pnm[1] = cid[1] >> 24; decoded.pnm[2] = (cid[1] >> 16) & 0xff; decoded.pnm[3] = (cid[1] >> 8) & 0xff; decoded.pnm[4] = cid[1] & 0xff; /* Word 3: Bits 32-63 * pnm[5] 63-56 * prv - 55-48 8-bit Product revision * psn - 47-16 32-bit Product serial number * psn 47-32 */ decoded.pnm[5] = cid[2] >> 24; decoded.pnm[6] = '\0'; decoded.prv = (cid[2] >> 16) & 0xff; decoded.psn = cid[2] << 16; /* Word 4: Bits 0-31 * psn 31-16 * mdt - 15:8 8-bit Manufacturing date * crc - 7:1 7-bit CRC7 */ decoded.psn |= cid[3] >> 16; decoded.mdt = (cid[3] >> 8) & 0xff; decoded.crc = (cid[3] >> 1) & 0x7f; finfo("mid: %02x cbx: %01x oid: %01x pnm: %s prv: %d psn: %08x mdt: %02x\ crc: %02x\n", decoded.mid, decoded.cbx, decoded.oid, decoded.pnm, decoded.prv, (unsigned long)decoded.psn, decoded.mdt, decoded.crc); } #endif /**************************************************************************** * Name: mmcsd_decode_scr * * Description: * Show the contents of the SD Configuration Register (SCR). The only * value retained is: priv->buswidth; * ****************************************************************************/ static void mmcsd_decode_scr(FAR struct mmcsd_state_s *priv, uint32_t scr[2]) { #ifdef CONFIG_DEBUG_FS_INFO struct mmcsd_scr_s decoded; #endif /* Word 1, bits 63:32 * SCR_STRUCTURE 63:60 4-bit SCR structure version * SD_VERSION 59:56 4-bit SD memory spec. version * DATA_STATE_AFTER_ERASE 55:55 1-bit erase status * SD_SECURITY 54:52 3-bit SD security support level * SD_BUS_WIDTHS 51:48 4-bit bus width indicator * Reserved 47:34 14-bit SD reserved space * CMD_SUPPORT 33:32 2-bit command supported (bit33 for cmd23) */ #ifdef CONFIG_ENDIAN_BIG /* Card transfers SCR in big-endian order */ priv->buswidth = (scr[0] >> 16) & 15; priv->cmd23support = (scr[0] >> 1) & 1; #else priv->buswidth = (scr[0] >> 8) & 15; priv->cmd23support = (scr[0] >> 25) & 1; #endif #ifdef CONFIG_DEBUG_FS_INFO #ifdef CONFIG_ENDIAN_BIG /* Card SCR is big-endian order / CPU also big-endian * 60 56 52 48 44 40 36 32 * VVVV SSSS ESSS BBBB RRRR RRRR RRRR RRRR */ decoded.scrversion = scr[0] >> 28; decoded.sdversion = (scr[0] >> 24) & 15; decoded.erasestate = (scr[0] >> 23) & 1; decoded.security = (scr[0] >> 20) & 7; #else /* Card SCR is big-endian order / CPU is little-endian * 36 32 44 40 52 48 60 56 * RRRR RRRR RRRR RRRR ESSS BBBB VVVV SSSS */ decoded.scrversion = (scr[0] >> 4) & 15; decoded.sdversion = scr[0] & 15; decoded.erasestate = (scr[0] >> 15) & 1; decoded.security = (scr[0] >> 12) & 7; #endif decoded.buswidth = priv->buswidth; #endif /* Word 1, bits 63:32 * Reserved 31:0 32-bits reserved for manufacturing usage. */ #ifdef CONFIG_DEBUG_FS_INFO decoded.mfgdata = scr[1]; /* Might be byte reversed! */ finfo("SCR:\n"); finfo(" SCR_STRUCTURE: %d SD_VERSION: %d\n", decoded.scrversion, decoded.sdversion); finfo(" DATA_STATE_AFTER_ERASE: %d SD_SECURITY: %d SD_BUS_WIDTHS: %x\n", decoded.erasestate, decoded.security, decoded.buswidth); finfo(" Manufacturing data: %08x\n", decoded.mfgdata); #endif } #ifdef CONFIG_MMCSD_IOCSUPPORT /**************************************************************************** * Name: mmcsd_switch * * Description: * Execute CMD6 to switch the mode of operation of the selected device or * modify the EXT_CSD registers. * ****************************************************************************/ static int mmcsd_switch(FAR struct mmcsd_state_s *priv, uint32_t arg) { /* After putting a slave into transfer state, master sends * CMD6(SWITCH) to set the PARTITION_ACCESS bits in the EXT_CSD * register, byte[179].After that, master can use the Multiple Block * read and write commands (CMD23, CMD18 and CMD25) to access the * RPMB partition. * PARTITION_CONFIG[179](see 7.4.69) * Bit[2:0] : PARTITION_ACCESS (before BOOT_PARTITION_ACCESS) * User selects partitions to access: * 0x0 : No access to boot partition (default) * 0x1 : R/W boot partition 1 * 0x2 : R/W boot partition 2 * 0x3 : R/W Replay Protected Memory Block (RPMB) * 0x4 : Access to General Purpose partition 1 * 0x5 : Access to General Purpose partition 2 * 0x6 : Access to General Purpose partition 3 * 0x7 : Access to General Purpose partition 4 * * CMD6 Argument(see 6.10.4) * [31:26] Set to 0 * [25:24] Access Bits * 00 Command Set * 01 Set Bits * 10 Clear Bits * 11 Write Byte * [23:16] Index * [15:8] Value * [7:3] Set to 0 * [2:0] Cmd Set */ mmcsd_sendcmdpoll(priv, MMCSD_CMD6, arg); return mmcsd_recv_r1(priv, MMCSD_CMD6); } #endif /* CONFIG_MMCSD_IOCSUPPORT */ /**************************************************************************** * Name: mmcsd_get_r1 * * Description: * Get the R1 status of the card using CMD13 * ****************************************************************************/ static int mmcsd_get_r1(FAR struct mmcsd_state_s *priv, FAR uint32_t *r1) { uint32_t local_r1; int ret; DEBUGASSERT(priv != NULL && r1 != NULL); /* Send CMD13, SEND_STATUS. The addressed card responds by sending its * R1 card status register. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD13, (uint32_t)priv->rca << 16); ret = SDIO_RECVR1(priv->dev, MMCSD_CMD13, &local_r1); if (ret == OK) { /* Check if R1 reports an error */ if ((local_r1 & MMCSD_R1_ERRORMASK) != 0) { /* Card locked is considered an error. Save the card locked * indication for later use. */ priv->locked = ((local_r1 & MMCSD_R1_CARDISLOCKED) != 0); /* We must tell someone which error bits were set. */ fwarn("WARNING: mmcsd_get_r1 returned errors: R1=%08" PRIx32 "\n", local_r1); ret = -EIO; } else { /* No errors, return R1 */ *r1 = local_r1; } } return ret; } /**************************************************************************** * Name: mmcsd_verifystate * * Description: * Verify that the card is in STANDBY state * ****************************************************************************/ static int mmcsd_verifystate(FAR struct mmcsd_state_s *priv, uint32_t state) { uint32_t r1; int ret; /* Get the current R1 status from the card */ ret = mmcsd_get_r1(priv, &r1); if (ret != OK) { ferr("ERROR: mmcsd_get_r1 failed: %d\n", ret); return ret; } /* Now check if the card is in the expected state. */ if (IS_STATE(r1, state)) { /* Yes.. return Success */ priv->wrbusy = false; return OK; } return -EINVAL; } /**************************************************************************** * Transfer Helpers ****************************************************************************/ /**************************************************************************** * Name: mmcsd_wrprotected * * Description: * Return true if the card is nlocked or write protected. * ****************************************************************************/ static bool mmcsd_wrprotected(FAR struct mmcsd_state_s *priv) { /* Check if the card is locked (priv->locked) or write protected either (1) * via software as reported via the CSD and retained in priv->wrprotect or * (2) via the mechanical write protect on the card (which we get from the * SDIO driver via SDIO_WRPROTECTED) */ return (priv->wrprotect || priv->locked || SDIO_WRPROTECTED(priv->dev)); } /**************************************************************************** * Name: mmcsd_eventwait * * Description: * Wait for the specified events to occur. Check for wakeup on error * events. * ****************************************************************************/ static int mmcsd_eventwait(FAR struct mmcsd_state_s *priv, sdio_eventset_t failevents) { sdio_eventset_t wkupevent; /* Wait for the set of events enabled by SDIO_EVENTENABLE. */ wkupevent = SDIO_EVENTWAIT(priv->dev); /* SDIO_EVENTWAIT returns the event set containing the event(s) that ended * the wait. It should always be non-zero, but may contain failure as * well as success events. Check if it contains any failure events. */ if ((wkupevent & failevents) != 0) { /* Yes.. the failure event is probably SDIOWAIT_TIMEOUT */ ferr("ERROR: Awakened with %02x\n", wkupevent); return wkupevent & SDIOWAIT_TIMEOUT ? -ETIMEDOUT : -EIO; } /* Since there are no failure events, we must have been awakened by one * (or more) success events. */ return OK; } /**************************************************************************** * Name: mmcsd_transferready * * Description: * Check if the MMC/SD card is ready for the next read or write transfer. * Ready means: (1) card still in the slot, and (2) if the last transfer * was a write transfer, the card is no longer busy from that transfer. * ****************************************************************************/ static int mmcsd_transferready(FAR struct mmcsd_state_s *priv) { clock_t starttime; clock_t elapsed; uint32_t r1; int ret; /* First, check if the card has been removed. */ if (IS_EMPTY(priv) || !SDIO_PRESENT(priv->dev)) { ferr("ERROR: Card has been removed\n"); return -ENODEV; } /* If the last data transfer was not a write, then we do not have to check * the card status. */ else if (!priv->wrbusy) { return OK; } /* The card is still present and the last transfer was a write transfer. * Loop, querying the card state. Return when (1) the card is in the * TRANSFER state, (2) the card stays in the PROGRAMMING state too long, * or (3) the card is in any other state. * * The PROGRAMMING state occurs normally after a WRITE operation. During * this time, the card may be busy completing the WRITE and is not * available for other operations. The card will transition from the * PROGRAMMING state to the TRANSFER state when the card completes the * WRITE operation. */ #if defined(CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE) ret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (ret != OK) { ferr("ERROR: mmcsd_eventwait for transfer ready failed: %d\n", ret); } #endif starttime = clock_systime_ticks(); do { /* Get the current R1 status from the card */ ret = mmcsd_get_r1(priv, &r1); if (ret != OK) { ferr("ERROR: mmcsd_get_r1 failed: %d\n", ret); goto errorout; } /* Now check if the card is in the expected transfer state. */ if (IS_STATE(r1, MMCSD_R1_STATE_TRAN)) { /* Yes.. return Success */ priv->wrbusy = false; return OK; } /* Check for the programming state. This is not an error. It means * that the card is still busy from the last (write) transfer. The * card can also still be receiving data, for example, if hardware * receive FIFOs are not yet empty. */ else if (!IS_STATE(r1, MMCSD_R1_STATE_PRG) && !IS_STATE(r1, MMCSD_R1_STATE_RCV)) { /* Any other state would be an error in this context. There is * a possibility that the card is not selected. In this case, * it could be in STANDBY or DISCONNECTED state and the fix * might be to send CMD7 to re-select the card. Consider this * if this error occurs. */ ferr("ERROR: Unexpected R1 state: %08" PRIx32 "\n", r1); ret = -EINVAL; goto errorout; } /* Do not hog the CPU */ #ifdef CONFIG_MMCSD_CHECK_READY_STATUS_WITHOUT_SLEEP /* Use sched_yield when tick is big to avoid low writing speed */ sched_yield(); #else MMCSD_USLEEP(1000); #endif /* We are still in the programming state. Calculate the elapsed * time... we can't stay in this loop forever! */ elapsed = clock_systime_ticks() - starttime; } while (elapsed < TICK_PER_SEC); return -ETIMEDOUT; errorout: mmcsd_removed(priv); return ret; } /**************************************************************************** * Name: mmcsd_stoptransmission * * Description: * Send STOP_TRANSMISSION * ****************************************************************************/ #if MMCSD_MULTIBLOCK_LIMIT != 1 static int mmcsd_stoptransmission(FAR struct mmcsd_state_s *priv) { int ret; /* Send CMD12, STOP_TRANSMISSION, and verify good R1 return status */ mmcsd_sendcmdpoll(priv, MMCSD_CMD12, 0); ret = mmcsd_recv_r1(priv, MMCSD_CMD12); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD12 failed: %d\n", ret); } return ret; } #endif /**************************************************************************** * Name: mmcsd_setblocklen * * Description: * Set the block length. * ****************************************************************************/ static int mmcsd_setblocklen(FAR struct mmcsd_state_s *priv, uint32_t blocklen) { int ret = OK; /* Is the block length already selected in the card? */ if (priv->selblocklen != blocklen) { /* Send CMD16 = SET_BLOCKLEN. This command sets the block length (in * bytes) for all following block commands (read and write). Default * block length is specified in the CSD. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD16, blocklen); ret = mmcsd_recv_r1(priv, MMCSD_CMD16); if (ret == OK) { priv->selblocklen = blocklen; } else { ferr("ERROR: mmcsd_recv_r1 for CMD16 failed: %d\n", ret); } } return ret; } #if MMCSD_MULTIBLOCK_LIMIT != 1 /**************************************************************************** * Name: mmcsd_setblockcount * * Description: * Set the block counts. * ****************************************************************************/ static int mmcsd_setblockcount(FAR struct mmcsd_state_s *priv, uint32_t nblocks) { int ret; mmcsd_sendcmdpoll(priv, MMCSD_CMD23, nblocks); ret = mmcsd_recv_r1(priv, MMCSD_CMD23); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD23 failed: %d\n", ret); } return ret; } #endif /**************************************************************************** * Name: mmcsd_readsingle * * Description: * Read a single block of data. * ****************************************************************************/ static ssize_t mmcsd_readsingle(FAR struct mmcsd_state_s *priv, FAR uint8_t *buffer, off_t startblock) { off_t offset; int ret; finfo("startblock=%jd\n", (intmax_t)startblock); DEBUGASSERT(priv != NULL && buffer != NULL); /* Check if the card is locked */ if (priv->locked) { ferr("ERROR: Card is locked\n"); return -EPERM; } #if defined(CONFIG_SDIO_DMA) && defined(CONFIG_ARCH_HAVE_SDIO_PREFLIGHT) /* If we think we are going to perform a DMA transfer, make sure that we * will be able to before we commit the card to the operation. */ if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMAPREFLIGHT(priv->dev, buffer, priv->blocksize); if (ret != OK) { return ret; } } #endif /* Verify that the card is ready for the transfer. The card may still be * busy from the preceding write transfer. It would be simpler to check * for write busy at the end of each write, rather than at the beginning of * each read AND write, but putting the busy-wait at the beginning of the * transfer allows for more overlap and, hopefully, better performance */ ret = mmcsd_transferready(priv); if (ret != OK) { ferr("ERROR: Card not ready: %d\n", ret); return ret; } /* If this is a byte addressed SD card, then convert sector start sector * number to a byte offset */ if (IS_BLOCK(priv->type)) { offset = startblock; } else { offset = startblock << priv->blockshift; } finfo("offset=%jd\n", (intmax_t)offset); /* Select the block size for the card */ ret = mmcsd_setblocklen(priv, priv->blocksize); if (ret != OK) { ferr("ERROR: mmcsd_setblocklen failed: %d\n", ret); return ret; } /* Configure SDIO controller hardware for the read transfer */ SDIO_BLOCKSETUP(priv->dev, priv->blocksize, 1); SDIO_WAITENABLE(priv->dev, SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR, MMCSD_BLOCK_RDATADELAY); #ifdef CONFIG_SDIO_DMA if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMARECVSETUP(priv->dev, buffer, priv->blocksize); if (ret != OK) { finfo("SDIO_DMARECVSETUP: error %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } else #endif { SDIO_RECVSETUP(priv->dev, buffer, priv->blocksize); } /* Send CMD17, READ_SINGLE_BLOCK: Read a block of the size selected * by the mmcsd_setblocklen() and verify that good R1 status is * returned. The card state should change from Transfer to Sending-Data * state. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD17, offset); ret = mmcsd_recv_r1(priv, MMCSD_CMD17); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD17 failed: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } /* Then wait for the data transfer to complete */ ret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (ret != OK) { ferr("ERROR: CMD17 transfer failed: %d\n", ret); return ret; } /* Return value: One sector read */ return 1; } /**************************************************************************** * Name: mmcsd_readmultiple * * Description: * Read multiple, contiguous blocks of data from the physical device. * ****************************************************************************/ #if MMCSD_MULTIBLOCK_LIMIT != 1 static ssize_t mmcsd_readmultiple(FAR struct mmcsd_state_s *priv, FAR uint8_t *buffer, off_t startblock, size_t nblocks) { size_t nbytes = nblocks << priv->blockshift; off_t offset; int ret; finfo("startblock=%jd nblocks=%zu\n", (intmax_t)startblock, nblocks); DEBUGASSERT(priv != NULL && buffer != NULL && nblocks > 1); /* Check if the card is locked */ if (priv->locked) { ferr("ERROR: Card is locked\n"); return -EPERM; } #if defined(CONFIG_SDIO_DMA) && defined(CONFIG_ARCH_HAVE_SDIO_PREFLIGHT) /* If we think we are going to perform a DMA transfer, make sure that we * will be able to before we commit the card to the operation. */ if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMAPREFLIGHT(priv->dev, buffer, nbytes); if (ret != OK) { return ret; } } #endif /* Verify that the card is ready for the transfer. The card may still be * busy from the preceding write transfer. It would be simpler to check * for write busy at the end of each write, rather than at the beginning of * each read AND write, but putting the busy-wait at the beginning of the * transfer allows for more overlap and, hopefully, better performance */ ret = mmcsd_transferready(priv); if (ret != OK) { ferr("ERROR: Card not ready: %d\n", ret); return ret; } /* If this is a byte addressed SD card, then convert both the total * transfer size to bytes and the sector start sector number to a byte * offset */ if (IS_BLOCK(priv->type)) { offset = startblock; } else { offset = startblock << priv->blockshift; } finfo("nbytes=%zu byte offset=%jd\n", nbytes, (intmax_t)offset); /* Select the block size for the card */ ret = mmcsd_setblocklen(priv, priv->blocksize); if (ret != OK) { ferr("ERROR: mmcsd_setblocklen failed: %d\n", ret); return ret; } /* Configure SDIO controller hardware for the read transfer */ SDIO_BLOCKSETUP(priv->dev, priv->blocksize, nblocks); SDIO_WAITENABLE(priv->dev, SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR, nblocks * MMCSD_BLOCK_RDATADELAY); #ifdef CONFIG_SDIO_DMA if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMARECVSETUP(priv->dev, buffer, nbytes); if (ret != OK) { finfo("SDIO_DMARECVSETUP: error %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } else #endif { SDIO_RECVSETUP(priv->dev, buffer, nbytes); } #ifdef CONFIG_MMCSD_MMCSUPPORT if (IS_MMC(priv->type) || (IS_SD(priv->type) && priv->cmd23support)) #else if (IS_SD(priv->type) && priv->cmd23support) #endif { ret = mmcsd_setblockcount(priv, nblocks); if (ret != OK) { return ret; } } /* Send CMD18, READ_MULT_BLOCK: Read a block of the size selected by * the mmcsd_setblocklen() and verify that good R1 status is returned */ mmcsd_sendcmdpoll(priv, MMCSD_CMD18, offset); ret = mmcsd_recv_r1(priv, MMCSD_CMD18); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD18 failed: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } /* Wait for the transfer to complete */ ret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (ret != OK) { ferr("ERROR: CMD18 transfer failed: %d\n", ret); return ret; } if (IS_SD(priv->type) && !priv->cmd23support) { /* Send STOP_TRANSMISSION */ ret = mmcsd_stoptransmission(priv); if (ret != OK) { ferr("ERROR: mmcsd_stoptransmission failed: %d\n", ret); } } /* On success, return the number of blocks read */ return nblocks; } #endif /**************************************************************************** * Name: mmcsd_writesingle * * Description: * Write a single block of data to the physical device. * ****************************************************************************/ static ssize_t mmcsd_writesingle(FAR struct mmcsd_state_s *priv, FAR const uint8_t *buffer, off_t startblock) { off_t offset; int ret; finfo("startblock=%jd\n", (intmax_t)startblock); DEBUGASSERT(priv != NULL && buffer != NULL); /* Check if the card is locked or write protected (either via software or * via the mechanical write protect on the card) */ if (mmcsd_wrprotected(priv)) { ferr("ERROR: Card is locked or write protected\n"); return -EPERM; } #if defined(CONFIG_SDIO_DMA) && defined(CONFIG_ARCH_HAVE_SDIO_PREFLIGHT) /* If we think we are going to perform a DMA transfer, make sure that we * will be able to before we commit the card to the operation. */ if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMAPREFLIGHT(priv->dev, buffer, priv->blocksize); if (ret != OK) { return ret; } } #endif /* Verify that the card is ready for the transfer. The card may still be * busy from the preceding write transfer. It would be simpler to check * for write busy at the end of each write, rather than at the beginning of * each read AND write, but putting the busy-wait at the beginning of the * transfer allows for more overlap and, hopefully, better performance */ ret = mmcsd_transferready(priv); if (ret != OK) { ferr("ERROR: Card not ready: %d\n", ret); return ret; } /* If this is a byte addressed SD card, then convert sector start sector * number to a byte offset */ if (IS_BLOCK(priv->type)) { offset = startblock; } else { offset = startblock << priv->blockshift; } finfo("offset=%jd\n", (intmax_t)offset); /* Select the block size for the card */ ret = mmcsd_setblocklen(priv, priv->blocksize); if (ret != OK) { ferr("ERROR: mmcsd_setblocklen failed: %d\n", ret); return ret; } /* If Controller does not need DMA setup before the write then send CMD24 * now. */ if ((priv->caps & SDIO_CAPS_DMABEFOREWRITE) == 0) { /* Send CMD24, WRITE_BLOCK, and verify good R1 status is returned */ mmcsd_sendcmdpoll(priv, MMCSD_CMD24, offset); ret = mmcsd_recv_r1(priv, MMCSD_CMD24); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD24 failed: %d\n", ret); return ret; } } /* Configure SDIO controller hardware for the write transfer */ SDIO_BLOCKSETUP(priv->dev, priv->blocksize, 1); SDIO_WAITENABLE(priv->dev, SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR, MMCSD_BLOCK_WDATADELAY); #ifdef CONFIG_SDIO_DMA if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMASENDSETUP(priv->dev, buffer, priv->blocksize); if (ret != OK) { finfo("SDIO_DMASENDSETUP: error %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } else #endif { SDIO_SENDSETUP(priv->dev, buffer, priv->blocksize); } /* If Controller needs DMA setup before write then only send CMD24 now. */ if ((priv->caps & SDIO_CAPS_DMABEFOREWRITE) != 0) { /* Send CMD24, WRITE_BLOCK, and verify good R1 status is returned */ mmcsd_sendcmdpoll(priv, MMCSD_CMD24, offset); ret = mmcsd_recv_r1(priv, MMCSD_CMD24); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD24 failed: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } /* Wait for the transfer to complete */ ret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (ret != OK) { ferr("ERROR: CMD24 transfer failed: %d\n", ret); return ret; } /* Flag that a write transfer is pending that we will have to check for * write complete at the beginning of the next transfer. */ priv->wrbusy = true; #if defined(CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE) /* Arm the write complete detection with timeout */ SDIO_WAITENABLE(priv->dev, SDIOWAIT_WRCOMPLETE | SDIOWAIT_TIMEOUT, MMCSD_BLOCK_WDATADELAY); #endif /* On success, return the number of blocks written */ return 1; } /**************************************************************************** * Name: mmcsd_writemultiple * * Description: * Write multiple, contiguous blocks of data to the physical device. * This function expects that the data to be written is contained in * one large buffer that is pointed to by buffer. * ****************************************************************************/ #if MMCSD_MULTIBLOCK_LIMIT != 1 static ssize_t mmcsd_writemultiple(FAR struct mmcsd_state_s *priv, FAR const uint8_t *buffer, off_t startblock, size_t nblocks) { size_t nbytes = nblocks << priv->blockshift; off_t offset; int ret; int evret = OK; finfo("startblock=%jd nblocks=%zu\n", (intmax_t)startblock, nblocks); DEBUGASSERT(priv != NULL && buffer != NULL && nblocks > 1); /* Check if the card is locked or write protected (either via software or * via the mechanical write protect on the card) */ if (mmcsd_wrprotected(priv)) { ferr("ERROR: Card is locked or write protected\n"); return -EPERM; } #if defined(CONFIG_SDIO_DMA) && defined(CONFIG_ARCH_HAVE_SDIO_PREFLIGHT) /* If we think we are going to perform a DMA transfer, make sure that we * will be able to before we commit the card to the operation. */ if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMAPREFLIGHT(priv->dev, buffer, nbytes); if (ret != OK) { return ret; } } #endif /* Verify that the card is ready for the transfer. The card may still be * busy from the preceding write transfer. It would be simpler to check * for write busy at the end of each write, rather than at the beginning of * each read AND write, but putting the busy-wait at the beginning of the * transfer allows for more overlap and, hopefully, better performance */ ret = mmcsd_transferready(priv); if (ret != OK) { ferr("ERROR: Card not ready: %d\n", ret); return ret; } /* If this is a byte addressed SD card, then convert both the total * transfer size to bytes and the sector start sector number to a byte * offset */ if (IS_BLOCK(priv->type)) { offset = startblock; } else { offset = startblock << priv->blockshift; } finfo("nbytes=%zu byte offset=%jd\n", nbytes, (intmax_t)offset); /* Select the block size for the card */ ret = mmcsd_setblocklen(priv, priv->blocksize); if (ret != OK) { ferr("ERROR: mmcsd_setblocklen failed: %d\n", ret); return ret; } /* If this is an SD card, then send ACMD23 (SET_WR_BLK_ERASE_COUNT) just * before sending CMD25 (WRITE_MULTIPLE_BLOCK). This sets the number of * write blocks to be pre-erased and might make the following multiple * block write command faster. */ if (IS_SD(priv->type)) { /* Send CMD55, APP_CMD, a verify that good R1 status is returned */ mmcsd_sendcmdpoll(priv, SD_CMD55, (uint32_t)priv->rca << 16); ret = mmcsd_recv_r1(priv, SD_CMD55); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD55 (ACMD23) failed: %d\n", ret); return ret; } /* Send CMD23, SET_WR_BLK_ERASE_COUNT, and verify that good R1 status * is returned. */ mmcsd_sendcmdpoll(priv, SD_ACMD23, nblocks); ret = mmcsd_recv_r1(priv, SD_ACMD23); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for ACMD23 failed: %d\n", ret); return ret; } } #ifdef CONFIG_MMCSD_MMCSUPPORT if (IS_MMC(priv->type) || (IS_SD(priv->type) && priv->cmd23support)) #else if (IS_SD(priv->type) && priv->cmd23support) #endif { ret = mmcsd_setblockcount(priv, nblocks); if (ret != OK) { return ret; } } /* If Controller does not need DMA setup before the write then send CMD25 * now. */ if ((priv->caps & SDIO_CAPS_DMABEFOREWRITE) == 0) { /* Send CMD25, WRITE_MULTIPLE_BLOCK, and verify that good R1 status * is returned */ mmcsd_sendcmdpoll(priv, MMCSD_CMD25, offset); ret = mmcsd_recv_r1(priv, MMCSD_CMD25); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD25 failed: %d\n", ret); return ret; } } /* Configure SDIO controller hardware for the write transfer */ SDIO_BLOCKSETUP(priv->dev, priv->blocksize, nblocks); SDIO_WAITENABLE(priv->dev, SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR, nblocks * MMCSD_BLOCK_WDATADELAY); #ifdef CONFIG_SDIO_DMA if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMASENDSETUP(priv->dev, buffer, nbytes); if (ret != OK) { ferr("SDIO_DMASENDSETUP: error %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } else #endif { SDIO_SENDSETUP(priv->dev, buffer, nbytes); } /* If Controller needs DMA setup before write then only send CMD25 now. */ if ((priv->caps & SDIO_CAPS_DMABEFOREWRITE) != 0) { /* Send CMD25, WRITE_MULTIPLE_BLOCK, and verify that good R1 status * is returned */ mmcsd_sendcmdpoll(priv, MMCSD_CMD25, offset); ret = mmcsd_recv_r1(priv, MMCSD_CMD25); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD25 failed: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } /* Wait for the transfer to complete */ evret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (evret != OK) { ferr("ERROR: CMD25 transfer failed: %d\n", evret); /* If we return from here, we probably leave the sd-card in * Receive-data State. Instead, we will remember that * an error occurred and try to execute the STOP_TRANSMISSION * to put the sd-card back into Transfer State. */ } if (IS_SD(priv->type) && !priv->cmd23support) { /* Send STOP_TRANSMISSION */ ret = mmcsd_stoptransmission(priv); if (evret != OK) { return evret; } if (ret != OK) { ferr("ERROR: mmcsd_stoptransmission failed: %d\n", ret); return ret; } } else { if (evret != OK) { return evret; } } /* Flag that a write transfer is pending that we will have to check for * write complete at the beginning of the next transfer. */ priv->wrbusy = true; #if defined(CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE) /* Arm the write complete detection with timeout */ SDIO_WAITENABLE(priv->dev, SDIOWAIT_WRCOMPLETE | SDIOWAIT_TIMEOUT, nblocks * MMCSD_BLOCK_WDATADELAY); #endif /* On success, return the number of blocks written */ return nblocks; } #endif /**************************************************************************** * Name: mmcsd_open * * Description: Open the block device * ****************************************************************************/ static int mmcsd_open(FAR struct inode *inode) { FAR struct mmcsd_state_s *priv; int ret; finfo("Entry\n"); DEBUGASSERT(inode->i_private); priv = inode->i_private; /* Just increment the reference count on the driver */ DEBUGASSERT(priv->crefs < MAX_CREFS); ret = mmcsd_lock(priv); if (ret < 0) { return ret; } priv->crefs++; mmcsd_unlock(priv); return OK; } /**************************************************************************** * Name: mmcsd_close * * Description: close the block device * ****************************************************************************/ static int mmcsd_close(FAR struct inode *inode) { FAR struct mmcsd_state_s *priv; int ret; finfo("Entry\n"); DEBUGASSERT(inode->i_private); priv = inode->i_private; /* Decrement the reference count on the block driver */ DEBUGASSERT(priv->crefs > 0); ret = mmcsd_lock(priv); if (ret < 0) { return ret; } priv->crefs--; mmcsd_unlock(priv); return OK; } /**************************************************************************** * Name: mmcsd_read * * Description: * Read the specified number of sectors from the read-ahead buffer or from * the physical device. * ****************************************************************************/ static ssize_t mmcsd_read(FAR struct inode *inode, unsigned char *buffer, blkcnt_t startsector, unsigned int nsectors) { FAR struct mmcsd_state_s *priv; size_t sector; size_t endsector; ssize_t nread; ssize_t ret = nsectors; DEBUGASSERT(inode->i_private); priv = inode->i_private; finfo("startsector: %" PRIuOFF " nsectors: %u sectorsize: %d\n", startsector, nsectors, priv->blocksize); if (nsectors > 0) { ret = mmcsd_lock(priv); if (ret < 0) { return ret; } ret = nsectors; endsector = startsector + nsectors; for (sector = startsector; sector < endsector; sector += nread) { /* Read this sector into the user buffer */ #if MMCSD_MULTIBLOCK_LIMIT == 1 /* Read each block using only the single block transfer method */ nread = mmcsd_readsingle(priv, buffer, sector); #else nread = endsector - sector; if (nread > MMCSD_MULTIBLOCK_LIMIT) { nread = MMCSD_MULTIBLOCK_LIMIT; } if (nread == 1) { nread = mmcsd_readsingle(priv, buffer, sector); } else { nread = mmcsd_readmultiple(priv, buffer, sector, nread); } #endif if (nread < 0) { ret = nread; break; } /* Increment the buffer pointer by the sector size */ buffer += nread * priv->blocksize; } mmcsd_unlock(priv); } /* On success, return the number of blocks read */ return ret; } /**************************************************************************** * Name: mmcsd_write * * Description: * Write the specified number of sectors to the write buffer or to the * physical device. * ****************************************************************************/ static ssize_t mmcsd_write(FAR struct inode *inode, FAR const unsigned char *buffer, blkcnt_t startsector, unsigned int nsectors) { FAR struct mmcsd_state_s *priv; size_t sector; size_t endsector; ssize_t nwrite; ssize_t ret = nsectors; DEBUGASSERT(inode->i_private); priv = inode->i_private; finfo("startsector: %" PRIuOFF " nsectors: %u sectorsize: %d\n", startsector, nsectors, priv->blocksize); if (nsectors > 0) { ret = mmcsd_lock(priv); if (ret < 0) { return ret; } ret = nsectors; endsector = startsector + nsectors; for (sector = startsector; sector < endsector; sector += nwrite) { /* Write this sector into the user buffer */ #if MMCSD_MULTIBLOCK_LIMIT == 1 /* Write each block using only the single block transfer method */ nwrite = mmcsd_writesingle(priv, buffer, sector); #else nwrite = endsector - sector; if (nwrite > MMCSD_MULTIBLOCK_LIMIT) { nwrite = MMCSD_MULTIBLOCK_LIMIT; } if (nwrite == 1) { nwrite = mmcsd_writesingle(priv, buffer, sector); } else { nwrite = mmcsd_writemultiple(priv, buffer, sector, nwrite); } #endif if (nwrite < 0) { ret = nwrite; break; } /* Increment the buffer pointer by the sector size */ buffer += nwrite * priv->blocksize; } mmcsd_unlock(priv); } /* On success, return the number of blocks written */ return ret; } /**************************************************************************** * Name: mmcsd_geometry * * Description: Return device geometry * ****************************************************************************/ static int mmcsd_geometry(FAR struct inode *inode, struct geometry *geometry) { FAR struct mmcsd_state_s *priv; int ret = -EINVAL; finfo("Entry\n"); DEBUGASSERT(inode->i_private); if (geometry) { memset(geometry, 0, sizeof(*geometry)); /* Is there a (supported) card inserted in the slot? */ priv = inode->i_private; ret = mmcsd_lock(priv); if (ret < 0) { return ret; } if (IS_EMPTY(priv)) { /* No.. return ENODEV */ finfo("IS_EMPTY\n"); ret = -ENODEV; } else { /* Yes.. return the geometry of the card */ geometry->geo_available = true; geometry->geo_mediachanged = priv->mediachanged; geometry->geo_writeenabled = !mmcsd_wrprotected(priv); geometry->geo_nsectors = priv->nblocks; geometry->geo_sectorsize = priv->blocksize; finfo("available: true mediachanged: %s writeenabled: %s\n", geometry->geo_mediachanged ? "true" : "false", geometry->geo_writeenabled ? "true" : "false"); finfo("nsectors: %lu sectorsize: %" PRIi16 "\n", (unsigned long)geometry->geo_nsectors, geometry->geo_sectorsize); priv->mediachanged = false; ret = OK; } mmcsd_unlock(priv); } return ret; } /**************************************************************************** * Name: mmcsd_ioctl * * Description: Return device geometry * ****************************************************************************/ static int mmcsd_ioctl(FAR struct inode *inode, int cmd, unsigned long arg) { FAR struct mmcsd_state_s *priv; int ret; finfo("Entry\n"); DEBUGASSERT(inode->i_private); priv = inode->i_private; /* Process the IOCTL by command */ ret = mmcsd_lock(priv); if (ret < 0) { return ret; } switch (cmd) { case BIOC_PROBE: /* Check for media in the slot */ { finfo("BIOC_PROBE\n"); /* Probe the MMC/SD slot for media */ ret = mmcsd_probe(priv); if (ret != OK) { ferr("ERROR: mmcsd_probe failed: %d\n", ret); } } break; case BIOC_EJECT: /* Media has been removed from the slot */ { finfo("BIOC_EJECT\n"); /* Process the removal of the card */ ret = mmcsd_removed(priv); if (ret != OK) { ferr("ERROR: mmcsd_removed failed: %d\n", ret); } /* Enable logic to detect if a card is re-inserted */ SDIO_CALLBACKENABLE(priv->dev, SDIOMEDIA_INSERTED); } break; #ifdef CONFIG_MMCSD_IOCSUPPORT case MMC_IOC_CMD: /* MMCSD device ioctl commands */ { finfo("MMC_IOC_CMD\n"); ret = mmcsd_iocmd(priv, (FAR struct mmc_ioc_cmd *)arg); if (ret != OK) { ferr("ERROR: mmcsd_iocmd failed: %d\n", ret); } } break; case MMC_IOC_MULTI_CMD: /* MMCSD device ioctl muti commands */ { finfo("MMC_IOC_MULTI_CMD\n"); ret = mmcsd_multi_iocmd(priv, (FAR struct mmc_ioc_multi_cmd *)arg); if (ret != OK) { ferr("ERROR: mmcsd_iocmd failed: %d\n", ret); } } break; #endif default: ret = -ENOTTY; break; } mmcsd_unlock(priv); return ret; } /**************************************************************************** * Initialization/uninitialization/reset ****************************************************************************/ /**************************************************************************** * Name: mmcsd_mediachange * * Description: * This is a callback function from the SDIO driver that indicates that * there has been a change in the slot... either a card has been inserted * or a card has been removed. * * Assumptions: * This callback is NOT supposd to run in the context of an interrupt * handler; it is probably running in the context of work thread. * ****************************************************************************/ static void mmcsd_mediachange(FAR void *arg) { FAR struct mmcsd_state_s *priv = (FAR struct mmcsd_state_s *)arg; int ret; finfo("arg: %p\n", arg); DEBUGASSERT(priv); /* Is there a card present in the slot? */ ret = mmcsd_lock(priv); if (ret < 0) { return; } if (SDIO_PRESENT(priv->dev)) { /* Yes... process the card insertion. This could cause chaos if we * think that a card is already present and there are mounted file * systems! NOTE that mmcsd_probe() will always re-enable callbacks * appropriately. */ mmcsd_probe(priv); } else { /* No... process the card removal. This could have very bad * implications for any mounted file systems! NOTE that * mmcsd_removed() does NOT re-enable callbacks so we will need to * do that here. */ mmcsd_removed(priv); /* Enable logic to detect if a card is re-inserted */ SDIO_CALLBACKENABLE(priv->dev, SDIOMEDIA_INSERTED); } mmcsd_unlock(priv); } /**************************************************************************** * Name: mmcsd_widebus * * Description: * An SD card has been inserted and its SCR has been obtained. Select wide * (4-bit) bus operation if the card supports it. * * Assumptions: * This function is called only once per card insertion as part of the SD * card initialization sequence. It is not necessary to reselect the card * there is not need to check if wide bus operation has already been * selected. * ****************************************************************************/ static int mmcsd_widebus(FAR struct mmcsd_state_s *priv) { int ret; /* Check if the SD card supports wide bus operation (as reported in the * SCR or in the SDIO driver capabililities) */ if (IS_SD(priv->type) && (priv->buswidth & MMCSD_SCR_BUSWIDTH_4BIT) != 0 && (priv->caps & SDIO_CAPS_1BIT_ONLY) == 0) { /* SD card supports 4-bit BUS and host settings is not 1-bit only. */ finfo("Setting SD BUS width to 4-bit. Card type: %d\n", priv->type); /* Disconnect any CD/DAT3 pull up using ACMD42. ACMD42 is optional and * need not be supported by all SD calls. * * First end CMD55 APP_CMD with argument as card's RCA. */ mmcsd_sendcmdpoll(priv, SD_CMD55, (uint32_t)priv->rca << 16); ret = mmcsd_recv_r1(priv, SD_CMD55); if (ret != OK) { ferr("ERROR: RECVR1 for CMD55 of ACMD42: %d\n", ret); return ret; } /* Then send ACMD42 with the argument to disconnect the CD/DAT3 * pull-up * * TODO: May want to disable, then re-enable around data transfers * to support card detection" */ mmcsd_sendcmdpoll(priv, SD_ACMD42, MMCSD_ACMD42_CD_DISCONNECT); ret = mmcsd_recv_r1(priv, SD_ACMD42); if (ret != OK) { fwarn("WARNING: SD card does not support ACMD42: %d\n", ret); return ret; } /* Now send ACMD6 to select bus width operation, beginning * with CMD55, APP_CMD: */ mmcsd_sendcmdpoll(priv, SD_CMD55, (uint32_t)priv->rca << 16); ret = mmcsd_recv_r1(priv, SD_CMD55); if (ret != OK) { ferr("ERROR: RECVR1 for CMD55 of ACMD6: %d\n", ret); return ret; } /* Then send ACMD6 */ mmcsd_sendcmdpoll(priv, SD_ACMD6, MMCSD_ACMD6_BUSWIDTH_4); ret = mmcsd_recv_r1(priv, SD_ACMD6); if (ret != OK) { return ret; } } #ifdef CONFIG_MMCSD_MMCSUPPORT else if (IS_MMC(priv->type) && ((priv->buswidth & MMCSD_SCR_BUSWIDTH_4BIT) != 0 && (priv->caps & SDIO_CAPS_1BIT_ONLY) == 0)) { /* SD card supports 4-bit BUS and host settings is not 1-bit only. * Configuring MMC - Use MMC_SWITCH access modes. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD6, MMC_CMD6_BUSWIDTH(EXT_CSD_BUS_WIDTH_4)); ret = mmcsd_recv_r1(priv, MMCSD_CMD6); if (ret != OK) { ferr("ERROR: (MMCSD_CMD6) Setting MMC BUS width: %d\n", ret); return ret; } } #endif /* #ifdef CONFIG_MMCSD_MMCSUPPORT */ else if (!IS_SD(priv->type) && !IS_MMC(priv->type)) { /* Take this path when no MMC / SD is yet detected */ fwarn("No card inserted.\n"); SDIO_WIDEBUS(priv->dev, false); priv->widebus = false; SDIO_CLOCK(priv->dev, CLOCK_SDIO_DISABLED); MMCSD_USLEEP(MMCSD_CLK_DELAY); return OK; } /* Configure the SDIO peripheral */ if ((IS_MMC(priv->type) && ((priv->caps & SDIO_CAPS_1BIT_ONLY) == 0)) && ((priv->buswidth & MMCSD_SCR_BUSWIDTH_4BIT) != 0)) { /* JEDEC specs: A.8.3 Changing the data bus width: 'Bus testing * procedure' shows how mmc bus width may be detected. This driver * doesn't do it, so let the low level driver decide how to go with * the widebus selection. It may well be 1, 4 or 8 bits. * * For SD cards the priv->buswidth is set. */ finfo("Wide bus operation selected\n"); SDIO_WIDEBUS(priv->dev, true); priv->widebus = true; } else { finfo("Narrow bus operation selected\n"); SDIO_WIDEBUS(priv->dev, false); priv->widebus = false; } if (IS_SD(priv->type)) { if ((priv->buswidth & MMCSD_SCR_BUSWIDTH_4BIT) != 0) { SDIO_CLOCK(priv->dev, CLOCK_SD_TRANSFER_4BIT); } else { SDIO_CLOCK(priv->dev, CLOCK_SD_TRANSFER_1BIT); } } #ifdef CONFIG_MMCSD_MMCSUPPORT else { if (priv->caps & SDIO_CAPS_MMC_HS_MODE) { mmcsd_sendcmdpoll(priv, MMCSD_CMD6, MMC_CMD6_HS_TIMING(EXT_CSD_HS_TIMING_HS)); ret = mmcsd_recv_r1(priv, MMCSD_CMD6); if (ret != OK) { ferr("ERROR: (MMCSD_CMD6) Setting MMC speed mode: %d\n", ret); return ret; } priv->mode = EXT_CSD_HS_TIMING_HS; } SDIO_CLOCK(priv->dev, CLOCK_MMC_TRANSFER); } #endif /* #ifdef CONFIG_MMCSD_MMCSUPPORT */ MMCSD_USLEEP(MMCSD_CLK_DELAY); return OK; } /**************************************************************************** * Name: mmcsd_mmcinitialize * * Description: * We believe that there is an MMC card in the slot. Attempt to initialize * and configure the MMC card. This is called only from mmcsd_probe(). * ****************************************************************************/ #ifdef CONFIG_MMCSD_MMCSUPPORT static int mmcsd_mmcinitialize(FAR struct mmcsd_state_s *priv) { int ret; /* At this point, slow, ID mode clocking has been supplied to the card * and CMD0 has been sent successfully. CMD1 succeeded and ACMD41 failed * so there is good evidence that we have an MMC card inserted into the * slot. * * Send CMD2, ALL_SEND_CID. This implementation supports only one MMC * slot. If multiple cards were installed, each card would respond to * CMD2 by sending its CID (only one card completes the response at a * time). The driver should send CMD2 and assign an RCAs until no * response to ALL_SEND_CID is received. CMD2 causes transition to * identification state / card-identification mode. */ finfo("Initialising MMC card.\n"); mmcsd_sendcmdpoll(priv, MMCSD_CMD2, 0); ret = SDIO_RECVR2(priv->dev, MMCSD_CMD2, priv->cid); if (ret != OK) { ferr("ERROR: SDIO_RECVR2 for MMC CID failed: %d\n", ret); return ret; } mmcsd_decode_cid(priv, priv->cid); /* Send CMD3, SET_RELATIVE_ADDR. This command is used to assign a logical * address to the card. For MMC, the host assigns the address. CMD3 causes * transition to standby state/data-transfer mode */ priv->rca = 1; /* There is only one card */ mmcsd_sendcmdpoll(priv, MMC_CMD3, (uint32_t)priv->rca << 16); ret = mmcsd_recv_r1(priv, MMC_CMD3); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1(CMD3) failed: %d\n", ret); return ret; } /* This should have caused a transition to standby state. However, this * will not be reflected in the present R1/6 status. R1/6 contains the * state of the card when the command was received, not when it * completed execution. * * Verify that we are in standby state/data-transfer mode */ ret = mmcsd_verifystate(priv, MMCSD_R1_STATE_STBY); if (ret != OK) { ferr("ERROR: Failed to enter standby state\n"); return ret; } /* Send CMD9, SEND_CSD in standby state/data-transfer mode to obtain the * Card Specific Data (CSD) register, e.g., block length, card storage * capacity, etc. (Stays in standby state/data-transfer mode). * NOTE in v2.0 high capacity cards, the following values are always * returned: * - write block length = 9 = 2^9 = 512 * - read block length = 9 = 512 * - rw2 factor = 0x2 (010b) * - size_mult = 0 * We can't decode the CSD register yet as we also need to read the * extended CSD register. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD9, (uint32_t)priv->rca << 16); ret = SDIO_RECVR2(priv->dev, MMCSD_CMD9, priv->csd); if (ret != OK) { ferr("ERROR: Could not get SD CSD register: %d\n", ret); return ret; } /* Decode the CSD register to obtain version. We will need to * decode further if card is v4.0 or higher as it supports * ext_csd commands. */ mmcsd_decode_csd(priv, priv->csd); /* Set the Driver Stage Register (DSR) if (1) a CONFIG_MMCSD_DSR has been * provided and (2) the card supports a DSR register. If no DSR value * the card default value (0x0404) will be used. */ mmcsd_sendcmd4(priv); /* Select the card. * Send CMD7 with the argument == RCA in order to select the card * and send it in data-trasfer mode. Since we are supporting * only a single card, we just leave the card selected all of the time. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD7S, (uint32_t)priv->rca << 16); ret = mmcsd_recv_r1(priv, MMCSD_CMD7S); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD7 failed: %d\n", ret); return ret; } /* If the hardware only supports 4-bit transfer mode then we forced to * attempt to setup the card in this mode before checking the ext CSD * register. */ if ((priv->caps & SDIO_CAPS_4BIT_ONLY) != 0) { /* Select width (4-bit) bus operation */ priv->buswidth = MMCSD_SCR_BUSWIDTH_4BIT; ret = mmcsd_widebus(priv); if (ret != OK) { ferr("ERROR: Failed to set wide bus operation: %d\n", ret); } } /* CSD Decoding for MMC should be done after entering in data-transfer mode * because if the card has block addressing then extended CSD register * must be read in order to get the right number of blocks and capacity, * and BUS width but it has to be done in data-transfer mode. */ if (IS_BLOCK(priv->type)) { finfo("Card supports eMMC spec 4.0 (or greater). Reading ext_csd.\n"); ret = mmcsd_read_csd(priv, NULL); if (ret != OK) { ferr("ERROR: Failed to determinate number of blocks: %d\n", ret); return ret; } } mmcsd_decode_csd(priv, priv->csd); /* It's up to the driver to act on the widebus request. mmcsd_widebus() * enables the CLOCK_MMC_TRANSFER, so call it here always. */ ret = mmcsd_widebus(priv); if (ret != OK) { ferr("ERROR: Failed to set wide bus operation: %d\n", ret); } return OK; } /**************************************************************************** * Name: mmcsd_read_csd * * Description: * MMC card is detected with block addressing and this function will read * the correct number of blocks and capacity. Returns OK if ext CSD is read * correctly or error in not. * * Note: For some MCU architectures, buffer[] must be aligned. * ****************************************************************************/ static int mmcsd_read_csd(FAR struct mmcsd_state_s *priv, FAR uint8_t *data) { uint8_t buffer[512] aligned_data(16); int ret; DEBUGASSERT(priv != NULL); /* Check if the card is locked */ if (priv->locked) { ferr("ERROR: Card is locked\n"); return -EPERM; } memset(buffer, 0, sizeof(buffer)); #if defined(CONFIG_SDIO_DMA) && defined(CONFIG_ARCH_HAVE_SDIO_PREFLIGHT) /* If we think we are going to perform a DMA transfer, make sure that we * will be able to before we commit the card to the operation. */ if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMAPREFLIGHT(priv->dev, buffer, priv->blocksize); if (ret != OK) { return ret; } } #endif /* Verify that the card is ready for the transfer. The card may still be * busy from the preceding write transfer. It would be simpler to check * for write busy at the end of each write, rather than at the beginning of * each read AND write, but putting the busy-wait at the beginning of the * transfer allows for more overlap and, hopefully, better performance */ ret = mmcsd_transferready(priv); if (ret != OK) { ferr("ERROR: Card not ready: %d\n", ret); return ret; } /* Select the block size for the card (CMD16) */ ret = mmcsd_setblocklen(priv, 512); if (ret != OK) { ferr("ERROR: mmcsd_setblocklen failed: %d\n", ret); return ret; } /* Configure SDIO controller hardware for the read transfer */ SDIO_BLOCKSETUP(priv->dev, 512, 1); SDIO_WAITENABLE(priv->dev, SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR, MMCSD_BLOCK_RDATADELAY); #ifdef CONFIG_SDIO_DMA if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { finfo("Setting up for DMA transfer.\n"); ret = SDIO_DMARECVSETUP(priv->dev, buffer, 512); if (ret != OK) { finfo("SDIO_DMARECVSETUP: error %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } else #endif { SDIO_RECVSETUP(priv->dev, buffer, 512); } /* Send CMD8 in data-transfer mode to obtain the * extended Card Specific Data (CSD) register, e.g., block length, card * storage capacity, etc. */ mmcsd_sendcmdpoll(priv, MMC_CMD8, 0); ret = mmcsd_recv_r1(priv, MMC_CMD8); if (ret != OK) { ferr("ERROR: Could not get MMC extended CSD register: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } /* Then wait for the data transfer to complete */ ret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (ret != OK) { ferr("ERROR: CMD17 transfer failed: %d\n", ret); return ret; } priv->nblocks = (buffer[215] << 24) | (buffer[214] << 16) | (buffer[213] << 8) | buffer[212]; if (data != NULL) { memcpy(data, buffer, sizeof(buffer)); } finfo("MMC ext CSD read succsesfully, number of block %" PRId32 "\n", priv->nblocks); SDIO_GOTEXTCSD(priv->dev, buffer); /* Return value: One sector read */ return OK; } #endif #ifdef CONFIG_MMCSD_IOCSUPPORT /**************************************************************************** * Name: mmcsd_general_cmd_write * * Description: * Send cmd56 data, one sector size * ****************************************************************************/ static int mmcsd_general_cmd_write(FAR struct mmcsd_state_s *priv, FAR const uint8_t *buffer, off_t startblock) { int ret; DEBUGASSERT(priv != NULL && buffer != NULL); /* Check if the card is locked or write protected (either via software or * via the mechanical write protect on the card) */ if (mmcsd_wrprotected(priv)) { ferr("ERROR: Card is locked or write protected\n"); return -EPERM; } #if defined(CONFIG_SDIO_DMA) && defined(CONFIG_ARCH_HAVE_SDIO_PREFLIGHT) /* If we think we are going to perform a DMA transfer, make sure that we * will be able to before we commit the card to the operation. */ if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMAPREFLIGHT(priv->dev, buffer, priv->blocksize); if (ret != OK) { return ret; } } #endif /* Verify that the card is ready for the transfer. The card may still be * busy from the preceding write transfer. It would be simpler to check * for write busy at the end of each write, rather than at the beginning of * each read AND write, but putting the busy-wait at the beginning of the * transfer allows for more overlap and, hopefully, better performance */ ret = mmcsd_transferready(priv); if (ret != OK) { ferr("ERROR: Card not ready: %d\n", ret); return ret; } /* Select the block size for the card */ ret = mmcsd_setblocklen(priv, priv->blocksize); if (ret != OK) { ferr("ERROR: mmcsd_setblocklen failed: %d\n", ret); return ret; } /* If Controller does not need DMA setup before the write then send CMD56 * now. */ if ((priv->caps & SDIO_CAPS_DMABEFOREWRITE) == 0) { /* Send CMD56, WRITE_BLOCK, and verify good R1 status is returned */ mmcsd_sendcmdpoll(priv, MMCSD_CMD56WR, startblock); ret = mmcsd_recv_r1(priv, MMCSD_CMD56WR); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD56 failed: %d\n", ret); return ret; } } /* Configure SDIO controller hardware for the write transfer */ SDIO_BLOCKSETUP(priv->dev, priv->blocksize, 1); SDIO_WAITENABLE(priv->dev, SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR, MMCSD_BLOCK_WDATADELAY); #ifdef CONFIG_SDIO_DMA if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMASENDSETUP(priv->dev, buffer, priv->blocksize); if (ret != OK) { finfo("SDIO_DMASENDSETUP: error %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } else #endif { SDIO_SENDSETUP(priv->dev, buffer, priv->blocksize); } /* If Controller needs DMA setup before write then only send CMD24 now. */ if ((priv->caps & SDIO_CAPS_DMABEFOREWRITE) != 0) { /* Send CMD56, WRITE_BLOCK, and verify good R1 status is returned */ mmcsd_sendcmdpoll(priv, MMCSD_CMD56WR, startblock); ret = mmcsd_recv_r1(priv, MMCSD_CMD56WR); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD56 failed: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } /* Wait for the transfer to complete */ ret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (ret != OK) { ferr("ERROR: CMD56 transfer failed: %d\n", ret); return ret; } /* Flag that a write transfer is pending that we will have to check for * write complete at the beginning of the next transfer. */ priv->wrbusy = true; #if defined(CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE) /* Arm the write complete detection with timeout */ SDIO_WAITENABLE(priv->dev, SDIOWAIT_WRCOMPLETE | SDIOWAIT_TIMEOUT, MMCSD_BLOCK_WDATADELAY); #endif /* On success, return OK */ return OK; } /**************************************************************************** * Name: mmcsd_general_cmd_read * * Description: * Read cmd56 data, one sector size * ****************************************************************************/ static int mmcsd_general_cmd_read(FAR struct mmcsd_state_s *priv, FAR uint8_t *buffer, off_t startblock) { int ret; DEBUGASSERT(priv != NULL && buffer != NULL); /* Check if the card is locked */ if (priv->locked) { ferr("ERROR: Card is locked\n"); return -EPERM; } #if defined(CONFIG_SDIO_DMA) && defined(CONFIG_ARCH_HAVE_SDIO_PREFLIGHT) /* If we think we are going to perform a DMA transfer, make sure that we * will be able to before we commit the card to the operation. */ if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMAPREFLIGHT(priv->dev, buffer, priv->blocksize); if (ret != OK) { return ret; } } #endif /* Verify that the card is ready for the transfer. The card may still be * busy from the preceding write transfer. It would be simpler to check * for write busy at the end of each write, rather than at the beginning of * each read AND write, but putting the busy-wait at the beginning of the * transfer allows for more overlap and, hopefully, better performance */ ret = mmcsd_transferready(priv); if (ret != OK) { ferr("ERROR: Card not ready: %d\n", ret); return ret; } /* Select the block size for the card */ ret = mmcsd_setblocklen(priv, priv->blocksize); if (ret != OK) { ferr("ERROR: mmcsd_setblocklen failed: %d\n", ret); return ret; } /* Configure SDIO controller hardware for the read transfer */ SDIO_BLOCKSETUP(priv->dev, priv->blocksize, 1); SDIO_WAITENABLE(priv->dev, SDIOWAIT_TRANSFERDONE | SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR, MMCSD_BLOCK_RDATADELAY); #ifdef CONFIG_SDIO_DMA if ((priv->caps & SDIO_CAPS_DMASUPPORTED) != 0) { ret = SDIO_DMARECVSETUP(priv->dev, buffer, priv->blocksize); if (ret != OK) { finfo("SDIO_DMARECVSETUP: error %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } } else #endif { SDIO_RECVSETUP(priv->dev, buffer, priv->blocksize); } /* Send CMD56: Read a sector size data and verify that good R1 * status is returned. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD56RD, startblock); ret = mmcsd_recv_r1(priv, MMCSD_CMD56RD); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD56 failed: %d\n", ret); SDIO_CANCEL(priv->dev); return ret; } /* Then wait for the data transfer to complete */ ret = mmcsd_eventwait(priv, SDIOWAIT_TIMEOUT | SDIOWAIT_ERROR); if (ret != OK) { ferr("ERROR: CMD56 transfer failed: %d\n", ret); return ret; } /* Return value: OK */ return OK; } /**************************************************************************** * Name: mmcsd_iocmd * * Description: * MMCSD device ioctl commands. * ****************************************************************************/ static int mmcsd_iocmd(FAR struct mmcsd_state_s *priv, FAR struct mmc_ioc_cmd *ic_ptr) { uint32_t opcode; int ret = OK; DEBUGASSERT(priv != NULL && ic_ptr != NULL); opcode = ic_ptr->opcode & MMCSD_CMDIDX_MASK; switch (opcode) { case MMCSD_CMDIDX2: /* Get cid reg data */ { memcpy((FAR void *)(uintptr_t)ic_ptr->data_ptr, priv->cid, sizeof(priv->cid)); } break; case MMCSD_CMDIDX6: /* Switch commands */ { ret = mmcsd_switch(priv, ic_ptr->arg); if (ret != OK) { ferr("ERROR: mmcsd_switch failed: %d\n", ret); } } break; #ifdef CONFIG_MMCSD_MMCSUPPORT case MMC_CMDIDX8: /* Get extended csd reg data */ { ret = mmcsd_read_csd(priv, (FAR uint8_t *)(uintptr_t)ic_ptr->data_ptr); } break; #endif case MMCSD_CMDIDX56: /* General commands */ { if (ic_ptr->write_flag) { ret = mmcsd_general_cmd_write(priv, (FAR uint8_t *)(uintptr_t)(ic_ptr->data_ptr), ic_ptr->arg); if (ret != OK) { ferr("mmcsd_iocmd MMCSD_CMDIDX56 write failed.\n"); } } else { ret = mmcsd_general_cmd_read(priv, (FAR uint8_t *)(uintptr_t)(ic_ptr->data_ptr), ic_ptr->arg); if (ret != OK) { ferr("mmcsd_iocmd MMCSD_CMDIDX56 read failed.\n"); } } } break; default: { ferr("mmcsd_iocmd opcode unsupported.\n"); ret = -EINVAL; } break; } return ret; } /**************************************************************************** * Name: mmcsd_multi_iocmd * * Description: * MMCSD device ioctl multi commands. * ****************************************************************************/ static int mmcsd_multi_iocmd(FAR struct mmcsd_state_s *priv, FAR struct mmc_ioc_multi_cmd *imc_ptr) { int ret; int i; DEBUGASSERT(priv != NULL && imc_ptr != NULL); if (imc_ptr->num_of_cmds > MMC_IOC_MAX_CMDS) { ferr("mmcsd_multi_iocmd too many cmds.\n"); return -EINVAL; } for (i = 0; i < imc_ptr->num_of_cmds; ++i) { ret = mmcsd_iocmd(priv, &imc_ptr->cmds[i]); if (ret != OK) { ferr("cmds %d failed.\n", i); return ret; } } return OK; } #endif /**************************************************************************** * Name: mmcsd_sdinitialize * * Description: * We believe that there is an SD card in the slot. Attempt to initialize * and configure the SD card. This is called only from mmcsd_probe(). * ****************************************************************************/ static int mmcsd_sdinitialize(FAR struct mmcsd_state_s *priv) { uint32_t cid[4]; uint32_t scr[2]; int ret; /* At this point, clocking has been supplied to the card, both CMD0 and * ACMD41 (with OCR=0) have been sent successfully, the card is no longer * busy and (presumably) in the IDLE state so there is good evidence * that we have an SD card inserted into the slot. * * Send CMD2, ALL_SEND_CID. The SD CMD2 is similar to the MMC CMD2 except * that the buffer type used to transmit to response of the card (SD Memory * Card: Push-Pull, MMC: Open-Drain). This implementation supports only a * single SD card. If multiple cards were installed in the slot, each card * would respond to CMD2 by sending its CID (only one card completes the * response at a time). The driver should send CMD2 and obtain RCAs until * no response to ALL_SEND_CID is received. * * When an SD card receives the CMD2 command it should transition to the * identification state/card-identification mode */ mmcsd_sendcmdpoll(priv, MMCSD_CMD2, 0); ret = SDIO_RECVR2(priv->dev, MMCSD_CMD2, cid); if (ret != OK) { ferr("ERROR: SDIO_RECVR2 for SD CID failed: %d\n", ret); return ret; } mmcsd_decode_cid(priv, cid); /* Send CMD3, SEND_RELATIVE_ADDR. In both protocols, this command is used * to assign a logical address to the card. For MMC, the host assigns the * address; for SD, the memory card has this responsibility. CMD3 causes * transition to standby state/data-transfer mode * * Send CMD3 with argument 0, SD card publishes its RCA in the response. */ mmcsd_sendcmdpoll(priv, SD_CMD3, 0); ret = mmcsd_recv_r6(priv, SD_CMD3); if (ret != OK) { ferr("ERROR: mmcsd_recv_r6 for SD RCA failed: %d\n", ret); return ret; } finfo("RCA: %04x\n", priv->rca); /* This should have caused a transition to standby state. However, this * will not be reflected in the present R1/6 status. R1/6 contains the * state of the card when the command was received, not when it * completed execution. * * Verify that we are in standby state/data-transfer mode */ ret = mmcsd_verifystate(priv, MMCSD_R1_STATE_STBY); if (ret != OK) { ferr("ERROR: Failed to enter standby state\n"); return ret; } /* Send CMD9, SEND_CSD, in standby state/data-transfer mode to obtain the * Card Specific Data (CSD) register. The argument is the RCA that we * just obtained from CMD3. The card stays in standby state/data-transfer * mode. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD9, (uint32_t)priv->rca << 16); ret = SDIO_RECVR2(priv->dev, MMCSD_CMD9, priv->csd); if (ret != OK) { ferr("ERROR: Could not get SD CSD register(%d)\n", ret); return ret; } mmcsd_decode_csd(priv, priv->csd); /* Send CMD7 with the argument == RCA in order to select the card. * Since we are supporting only a single card, we just leave the * card selected all of the time. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD7S, (uint32_t)priv->rca << 16); ret = mmcsd_recv_r1(priv, MMCSD_CMD7S); if (ret != OK) { ferr("ERROR: mmcsd_recv_r1 for CMD7 failed: %d\n", ret); return ret; } /* Set the Driver Stage Register (DSR) if (1) a CONFIG_MMCSD_DSR has been * provided and (2) the card supports a DSR register. If no DSR value * the card default value (0x0404) will be used. */ mmcsd_sendcmd4(priv); /* Select high speed SD clocking (which may depend on the DSR setting) */ SDIO_CLOCK(priv->dev, CLOCK_SD_TRANSFER_1BIT); MMCSD_USLEEP(MMCSD_CLK_DELAY); /* If the hardware only supports 4-bit transfer mode then we forced to * attempt to setup the card in this mode before checking the SCR register. */ if ((priv->caps & SDIO_CAPS_4BIT_ONLY) != 0) { /* Select width (4-bit) bus operation */ priv->buswidth = MMCSD_SCR_BUSWIDTH_4BIT; ret = mmcsd_widebus(priv); if (ret != OK) { ferr("ERROR: Failed to set wide bus operation: %d\n", ret); } } /* Get the SD card Configuration Register (SCR). We need this now because * that configuration register contains the indication whether or not * this card supports wide bus operation. */ ret = mmcsd_get_scr(priv, scr); if (ret != OK) { ferr("ERROR: Could not get SD SCR register(%d)\n", ret); return ret; } mmcsd_decode_scr(priv, scr); if ((priv->caps & SDIO_CAPS_4BIT) != 0) { /* Select width (4-bit) bus operation (if the card supports it) */ ret = mmcsd_widebus(priv); if (ret != OK) { ferr("ERROR: Failed to set wide bus operation: %d\n", ret); } } /* TODO: If wide-bus selected, then send CMD6 to see if the card supports * high speed mode. A new SDIO method will be needed to set high speed * mode. */ return OK; } /**************************************************************************** * Name: mmcsd_cardidentify * * Description: * We believe that there is media in the slot. Attempt to initialize and * configure the card. This is called only from mmcsd_probe(). * ****************************************************************************/ static int mmcsd_cardidentify(FAR struct mmcsd_state_s *priv) { uint32_t response; uint32_t sdcapacity = MMCSD_ACMD41_STDCAPACITY; #ifdef CONFIG_MMCSD_MMCSUPPORT uint32_t mmccapacity = MMCSD_R3_HIGHCAPACITY; #endif clock_t start; clock_t elapsed; int ret; finfo("Identifying card...\n"); /* Assume failure to identify the card */ priv->type = MMCSD_CARDTYPE_UNKNOWN; /* Check if there is a card present in the slot. This is normally a * matter is of GPIO sensing. */ if (!SDIO_PRESENT(priv->dev)) { finfo("No card present\n"); return -ENODEV; } /* Set ID mode clocking (<400KHz) */ SDIO_CLOCK(priv->dev, CLOCK_IDMODE); /* For eMMC, Send CMD0 with argument 0xf0f0f0f0 as per JEDEC v4.41 * for pre-idle. No effect for SD. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD0, 0xf0f0f0f0); MMCSD_USLEEP(MMCSD_IDLE_DELAY); /* After power up at least 74 clock cycles are required prior to starting * bus communication */ up_udelay(MMCSD_POWERUP_DELAY); /* Then send CMD0 just once is standard procedure */ mmcsd_sendcmdpoll(priv, MMCSD_CMD0, 0); MMCSD_USLEEP(MMCSD_IDLE_DELAY); #ifdef CONFIG_MMCSD_MMCSUPPORT /* Send CMD1 which is supported only by MMC. if there is valid response * then the card is definitely of MMC type */ mmcsd_sendcmdpoll(priv, MMC_CMD1, MMCSD_VDD_33_34 | mmccapacity); ret = SDIO_RECVR3(priv->dev, MMC_CMD1, &response); /* Was the operating range set successfully */ if (ret != OK) { fwarn("WARNING: CMD1 RECVR3: %d. " "NOTE: This is expected for SD cards.\n", ret); /* CMD1 did not succeed, card is not MMC. Return to idle * to allow the communication to recover before another send. */ mmcsd_sendcmdpoll(priv, MMCSD_CMD0, 0); MMCSD_USLEEP(MMCSD_IDLE_DELAY); } else { /* CMD1 succeeded... this must be an MMC card */ finfo("MMC card detected\n"); priv->type = MMCSD_CARDTYPE_MMC; priv->buswidth |= MMCSD_SCR_BUSWIDTH_4BIT; /* Now, check if this is a MMC card/chip that supports block * addressing */ if ((response & MMCSD_R3_HIGHCAPACITY) != 0) { finfo("MMC card/chip with block addressing\n"); mmccapacity = MMCSD_R3_HIGHCAPACITY; priv->type |= MMCSD_CARDTYPE_BLOCK; } else { mmccapacity = MMCSD_R3_STDCAPACITY; } /* Check if the card is busy. Very confusing, BUSY is set LOW * if the card has not finished its initialization, so it really * means NOT busy. */ if ((response & MMCSD_CARD_BUSY) != 0) { /* NO.. We really should check the current state to see if the * MMC successfully made it to the IDLE state, but at least for * now, we will simply assume that that is the case. * * Then break out of the look with an MMC card identified */ finfo("MMC card/chip ready!\n"); return OK; } } if (!IS_MMC(priv->type)) #endif { /* Check for SDHC Version 2.x. Send CMD8 to verify SD card interface * operating condition. CMD 8 is reserved on SD version 1.0 and MMC. * * CMD8 Argument: * [31:12]: Reserved (shall be set to '0') * [11:8]: Supply Voltage (VHS) 0x1 (Range: 2.7-3.6 V) * [7:0]: Check Pattern (recommended 0xaa) * CMD8 Response: R7 */ ret = mmcsd_sendcmdpoll(priv, SD_CMD8, MMCSD_CMD8CHECKPATTERN | MMCSD_CMD8VOLTAGE_27); if (ret == OK) { /* CMD8 was sent successfully... Get the R7 response */ ret = SDIO_RECVR7(priv->dev, SD_CMD8, &response); } /* Were both the command sent and response received correctly? */ if (ret == OK) { /* CMD8 succeeded this is probably a SDHC card. Verify the * operating voltage and that the check pattern was correctly * echoed */ if (((response & MMCSD_R7VOLTAGE_MASK) == MMCSD_R7VOLTAGE_27) && ((response & MMCSD_R7ECHO_MASK) == MMCSD_R7CHECKPATTERN)) { finfo("SD V2.x card\n"); priv->type = MMCSD_CARDTYPE_SDV2; sdcapacity = MMCSD_ACMD41_HIGHCAPACITY; } else { ferr("ERROR: R7: %08" PRIx32 "\n", response); return -EIO; } } } /* At this point, type is either UNKNOWN, eMMC or SDV2. Try sending * CMD55 and (maybe) ACMD41 for up to 1 second or until the card * exits the IDLE state. CMD55 is supported by SD V1.x and SD V2.x, * but not MMC */ start = clock_systime_ticks(); elapsed = 0; do { /* We may have already determined that this card is an MMC card from * an earlier pass through this loop. In that case, we should * skip the SD-specific commands. */ #ifdef CONFIG_MMCSD_MMCSUPPORT if (!IS_MMC(priv->type)) #endif { /* Send CMD55 with argument = 0 */ mmcsd_sendcmdpoll(priv, SD_CMD55, 0); ret = mmcsd_recv_r1(priv, SD_CMD55); if (ret != OK) { /* I am a little confused.. I think both SD and MMC cards * support CMD55 (but maybe only SD cards support CMD55). * We'll make the the MMC vs. SD decision based on CMD1 and * ACMD41. */ ferr("ERROR: mmcsd_recv_r1(CMD55) failed: %d\n", ret); } else { /* Send ACMD41 */ mmcsd_sendcmdpoll(priv, SD_ACMD41, MMCSD_ACMD41_VOLTAGEWINDOW_33_32 | sdcapacity); ret = SDIO_RECVR3(priv->dev, SD_ACMD41, &response); if (ret != OK) { /* If the error is a timeout, then it is probably an MMC * card, but we will make the decision based on CMD1 * below. */ ferr("ERROR: ACMD41 RECVR3: %d\n", ret); } else { /* ACMD41 succeeded. ACMD41 is supported by SD V1.x and * SD V2.x, but not MMC. If we did not previously * determine that this is an SD V2.x (via CMD8), then this * must be SD V1.x */ finfo("R3: %08" PRIx32 "\n", response); if (priv->type == MMCSD_CARDTYPE_UNKNOWN) { finfo("SD V1.x card\n"); priv->type = MMCSD_CARDTYPE_SDV1; } /* Check if the card is busy. Very confusing, BUSY is set * LOW if the card has not finished its initialization, * so it really means NOT busy. */ if ((response & MMCSD_CARD_BUSY) != 0) { /* No.. We really should check the current state to * see if the SD card successfully made it to the IDLE * state, but at least for now, we will simply assume * that that is the case. * * Now, check if this is a SD V2.x card that supports * block addressing */ if ((response & MMCSD_R3_HIGHCAPACITY) != 0) { finfo("SD V2.x card with block addressing\n"); DEBUGASSERT(priv->type == MMCSD_CARDTYPE_SDV2); priv->type |= MMCSD_CARDTYPE_BLOCK; } /* And break out of the loop with an card identified */ break; } } } } /* If we get here then either (1) CMD55 failed, (2) CMD41 failed, or * (3) and SD or MMC card has been identified, but it is not yet in * the IDLE state. If SD card has not been identified, then we might * be looking at an MMC card. We can send the CMD1 to find out for * sure. CMD1 is supported by MMC cards, but not by SD cards. */ #ifdef CONFIG_MMCSD_MMCSUPPORT if (IS_MMC(priv->type)) { /* Send the MMC CMD1 to specify the operating voltage. CMD1 causes * transition to ready state/ card-identification mode. NOTE: If * the card does not support this voltage range, it will go the * inactive state. * * NOTE: An MMC card will only respond once to CMD1 (unless it is * busy). This is part of the logic used to determine how many * MMC cards are connected (This implementation supports only a * single MMC card). So we cannot re-send CMD1 without first * placing the card back into stand-by state (if the card is busy, * it will automatically go back to the standby state). */ mmcsd_sendcmdpoll(priv, MMC_CMD1, MMCSD_VDD_33_34 | mmccapacity); ret = SDIO_RECVR3(priv->dev, MMC_CMD1, &response); /* Was the operating range set successfully */ if (ret != OK) { ferr("ERROR: CMD1 RECVR3: %d\n", ret); } else { /* CMD1 succeeded... this must be an MMC card */ finfo("Confirmed MMC card present.\n"); priv->type = MMCSD_CARDTYPE_MMC; /* Now, check if this is a MMC card/chip that supports block * addressing */ if ((response & MMCSD_R3_HIGHCAPACITY) != 0) { mmccapacity = MMCSD_R3_HIGHCAPACITY; priv->type |= MMCSD_CARDTYPE_BLOCK; } else { mmccapacity = MMCSD_R3_STDCAPACITY; } /* Check if the card is busy. Very confusing, BUSY is set LOW * if the card has not finished its initialization, so it * really means NOT busy. */ if ((response & MMCSD_CARD_BUSY) != 0) { /* NO.. We really should check the current state to see if * the MMC successfully made it to the IDLE state, but at * least for now we will simply assume that that is the * case. * * Then break out of the look with an MMC card identified */ finfo("MMC card/chip is ready!\n"); break; } else { finfo("MMC card/chip is busy. Waiting for reply...\n"); } } } #endif /* Check the elapsed time. We won't keep trying this forever! */ elapsed = clock_systime_ticks() - start; } while (elapsed < TICK_PER_SEC); /* On successful reception while 'breaks', see above. */ /* We get here when the above loop completes, either (1) we could not * communicate properly with the card due to errors (and the loop times * out), or (2) it is an MMC or SD card that has successfully transitioned * to the IDLE state (well, at least, it provided its OCR saying that it * it is no longer busy). */ if (elapsed >= TICK_PER_SEC || priv->type == MMCSD_CARDTYPE_UNKNOWN) { priv->type = MMCSD_CARDTYPE_UNKNOWN; ferr("ERROR: Failed to identify card\n"); return -EIO; } return OK; } /**************************************************************************** * Name: mmcsd_probe * * Description: * Check for media inserted in a slot. Called (1) during initialization to * see if there was a card in the slot at power up, (2) when/if a media * insertion event occurs, or (3) if the BIOC_PROBE ioctl command is * received. * ****************************************************************************/ static int mmcsd_probe(FAR struct mmcsd_state_s *priv) { int ret; finfo("type: %d probed: %d\n", priv->type, priv->probed); /* If we have reliable card detection events and if we have * already probed the card, then we don't need to do anything * else */ #ifdef CONFIG_MMCSD_HAVE_CARDDETECT if (priv->probed && SDIO_PRESENT(priv->dev)) { return OK; } #endif /* Otherwise, we are going to probe the card. There are lots of * possibilities here: We may think that there is a card in the slot, * or not. There may be a card in the slot, or not. If there is * card in the slot, perhaps it is a different card than we one we * think is there? The safest thing to do is to process the card * removal first and start from known place. */ mmcsd_removed(priv); /* Now.. is there a card in the slot? */ if (SDIO_PRESENT(priv->dev)) { /* Yes.. probe it. First, what kind of card was inserted? */ finfo("Card present. Probing....\n"); ret = mmcsd_cardidentify(priv); if (ret != OK) { ferr("ERROR: Failed to initialize card: %d\n", ret); } else { /* Then initialize the driver according to the card type */ switch (priv->type) { /* Bit 1: SD version 1.x */ case MMCSD_CARDTYPE_SDV1: finfo("SD version 1.x .\n"); ret = mmcsd_sdinitialize(priv); break; /* SD version 2.x with byte addressing */ case MMCSD_CARDTYPE_SDV2: finfo("SD version 2.x with byte addressing.\n"); ret = mmcsd_sdinitialize(priv); break; /* SD version 2.x with block addressing */ case MMCSD_CARDTYPE_SDV2 | MMCSD_CARDTYPE_BLOCK: finfo("SD version 2.x with block addressing.\n"); ret = mmcsd_sdinitialize(priv); break; /* MMC card with byte addressing */ case MMCSD_CARDTYPE_MMC: finfo("MMC card with byte addressing.\n"); /* MMC card with block addressing */ case MMCSD_CARDTYPE_MMC | MMCSD_CARDTYPE_BLOCK: finfo("MMC card with block addressing.\n"); #ifdef CONFIG_MMCSD_MMCSUPPORT ret = mmcsd_mmcinitialize(priv); break; #endif /* Unknown card type */ case MMCSD_CARDTYPE_UNKNOWN: default: ferr("ERROR: Internal confusion: %d\n", priv->type); ret = -EPERM; break; } /* Was the card configured successfully? */ if (ret == OK) { /* Yes... */ finfo("Capacity: %" PRIu32 " Kbytes\n", MMCSD_CAPACITY(priv->nblocks, priv->blockshift)); priv->mediachanged = true; } /* When the card is identified, we have probed this card */ priv->probed = true; } /* Regardless of whether or not a card was successfully initialized, * there is apparently a card inserted. If it wasn't successfully * initialized, there's nothing we can do about it now. Perhaps it's * a bad card? The best we can do is wait for the card to be ejected * and re-inserted. Then we can try to initialize again. */ #ifdef CONFIG_MMCSD_HAVE_CARDDETECT /* Set up to receive asynchronous, media removal events */ SDIO_CALLBACKENABLE(priv->dev, SDIOMEDIA_EJECTED); #endif } else { /* There is no card in the slot */ finfo("No card\n"); #ifdef CONFIG_MMCSD_HAVE_CARDDETECT SDIO_CALLBACKENABLE(priv->dev, SDIOMEDIA_INSERTED); #endif ret = -ENODEV; } return ret; } /**************************************************************************** * Name: mmcsd_removed * * Description: * Disable support for media in the slot. Called (1) when/if a media * removal event occurs, or (2) if the BIOC_EJECT ioctl command is * received. * ****************************************************************************/ static int mmcsd_removed(FAR struct mmcsd_state_s *priv) { finfo("type: %d present: %d\n", priv->type, SDIO_PRESENT(priv->dev)); /* Forget the card geometry, pretend the slot is empty (it might not * be), and that the card has never been initialized. */ priv->blocksize = 0; priv->probed = false; priv->mediachanged = false; priv->wrbusy = false; priv->type = MMCSD_CARDTYPE_UNKNOWN; priv->rca = 0; priv->selblocklen = 0; /* Go back to the default 1-bit data bus. */ priv->buswidth = MMCSD_SCR_BUSWIDTH_1BIT; SDIO_WIDEBUS(priv->dev, false); priv->widebus = false; mmcsd_widebus(priv); /* Disable clocking to the card */ SDIO_CLOCK(priv->dev, CLOCK_SDIO_DISABLED); return OK; } /**************************************************************************** * Name: mmcsd_hwinitialize * * Description: * One-time hardware initialization. Called only from sdio_slotinitialize. * ****************************************************************************/ static int mmcsd_hwinitialize(FAR struct mmcsd_state_s *priv) { int ret; ret = mmcsd_lock(priv); if (ret < 0) { return ret; } /* Get the capabilities of the SDIO driver */ priv->caps = SDIO_CAPABILITIES(priv->dev); finfo("DMA supported: %d\n", (priv->caps & SDIO_CAPS_DMASUPPORTED) != 0); /* Attach and prepare MMC/SD interrupts */ if (SDIO_ATTACH(priv->dev)) { ferr("ERROR: Unable to attach MMC/SD interrupts\n"); mmcsd_unlock(priv); return -EBUSY; } finfo("Attached MMC/SD interrupts\n"); /* Register a callback so that we get informed if media is inserted or * removed from the slot (Initially all callbacks are disabled). */ SDIO_REGISTERCALLBACK(priv->dev, mmcsd_mediachange, (FAR void *)priv); /* Is there a card in the slot now? For an MMC/SD card, there are three * possible card detect mechanisms: * * 1. Mechanical insertion that can be detected using the WP switch * that is closed when a card is inserted into then SD slot (SD * "hot insertion capable" card connector only) * 2. Electrical insertion that can be sensed using the pull-up resistor * on CD/DAT3 (both SD/MMC), * 3. Or by periodic attempts to initialize the card from software. * * The behavior of SDIO_PRESENT() is to use whatever information is * available on the particular platform. If no card insertion information * is available (polling only), then SDIO_PRESENT() will always return * true and we will try to initialize the card. */ if (SDIO_PRESENT(priv->dev)) { /* Yes... probe for a card in the slot */ ret = mmcsd_probe(priv); if (ret != OK) { finfo("Slot not empty, but initialization failed: %d\n", ret); /* NOTE: The failure to initialize a card does not mean that * initialization has failed! A card could be installed in the slot * at a later time. ENODEV is return in this case, * sdio_slotinitialize will use this return value to set up the * card inserted callback event. */ ret = -ENODEV; } } else { /* ENODEV is returned to indicate that no card is inserted in the slot. * sdio_slotinitialize will use this return value to set up the card * inserted callback event. */ ret = -ENODEV; } /* OK is returned only if the slot initialized correctly AND the card in * the slot was successfully configured. */ mmcsd_unlock(priv); return ret; } /**************************************************************************** * Name: mmcsd_hwuninitialize * * Description: * Restore the MMC/SD slot to the uninitialized state. Called only from * sdio_slotinitialize on a failure to initialize. * ****************************************************************************/ static void mmcsd_hwuninitialize(FAR struct mmcsd_state_s *priv) { mmcsd_removed(priv); SDIO_RESET(priv->dev); } static FAR const char *mmc_get_mode_name(uint8_t mode) { switch (mode) { case EXT_CSD_HS_TIMING_BC: return "backwards compatibility"; case EXT_CSD_HS_TIMING_HS: return "high speed"; case EXT_CSD_HS_TIMING_HS200: return "HS200"; case EXT_CSD_HS_TIMING_HS400: return "HS400"; default: ferr("Unknown mode: %u\n", mode); return "Unknown"; } } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: mmcsd_slotinitialize * * Description: * Initialize one slot for operation using the MMC/SD interface * * Input Parameters: * minor - The MMC/SD minor device number. The MMC/SD device will be * registered as /dev/mmcsdN where N is the minor number * dev - And instance of an MMC/SD interface. The MMC/SD hardware should * be initialized and ready to use. * ****************************************************************************/ int mmcsd_slotinitialize(int minor, FAR struct sdio_dev_s *dev) { FAR struct mmcsd_state_s *priv; char devname[16]; int ret = -ENOMEM; finfo("minor: %d\n", minor); /* Sanity check */ #ifdef CONFIG_DEBUG_FEATURES if (minor < 0 || minor > 255 || !dev) { return -EINVAL; } #endif /* Allocate a MMC/SD state structure */ priv = (FAR struct mmcsd_state_s *) kmm_malloc(sizeof(struct mmcsd_state_s)); if (priv == NULL) { return -ENOMEM; } /* Initialize the MMC/SD state structure */ memset(priv, 0, sizeof(struct mmcsd_state_s)); nxmutex_init(&priv->lock); /* Bind the MMCSD driver to the MMCSD state structure */ priv->dev = dev; /* Initialize the hardware associated with the slot */ ret = mmcsd_hwinitialize(priv); /* Was the slot initialized successfully? */ if (ret != OK) { /* No... But the error ENODEV is returned if hardware * initialization succeeded but no card is inserted in the slot. * In this case, the no error occurred, but the driver is still * not ready. */ if (ret == -ENODEV) { /* No card in the slot (or if there is, we could not recognize * it).. Setup to receive the media inserted event */ SDIO_CALLBACKENABLE(priv->dev, SDIOMEDIA_INSERTED); finfo("MMC/SD slot is empty\n"); } else { /* Some other non-recoverable bad thing happened */ ferr("ERROR: Failed to initialize MMC/SD slot: %d\n", ret); goto errout_with_alloc; } } /* Create a MMCSD device name */ snprintf(devname, sizeof(devname), "/dev/mmcsd%d", minor); /* Inode private data is a reference to the MMCSD state structure */ ret = register_blockdriver(devname, &g_bops, 0, priv); if (ret < 0) { ferr("ERROR: register_blockdriver failed: %d\n", ret); goto errout_with_hwinit; } #ifdef CONFIG_MMCSD_PROCFS mmcsd_initialize_procfs(); #endif finfo("MMC: %s %" PRIu64 "KB %s %s mode\n", devname, ((uint64_t)priv->nblocks << priv->blockshift) >> 10, priv->widebus ? "4-bits" : "1-bit", mmc_get_mode_name(priv->mode)); return OK; errout_with_hwinit: mmcsd_hwuninitialize(priv); errout_with_alloc: nxmutex_destroy(&priv->lock); kmm_free(priv); return ret; } #endif /* defined (CONFIG_MMCSD) && defined (CONFIG_MMCSD_SDIO) */