#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

menu "System Logging"

# Selected if the architecture has its own, built-in SYSLOGging enabled

config ARCH_SYSLOG
	bool
	default n

comment "SYSLOG options"

config SYSLOG_MAX_CHANNELS
	int "Maximum SYSLOG channels"
	default 1
	---help---
		Maximum number of supported SYSLOG channels.

config RAMLOG
	bool "RAM log device support"
	default n
	---help---
		This is a driver that was intended to support debugging output,
		aka syslogging, when the normal serial output is not available.
		For example, if you are using a telnet or USB serial console,
		the debug output will get lost.  However, the RAMLOG device should
		be usable even if system logging is disabled.

		This driver is similar to a pipe in that it saves the debugging
		output in a FIFO in RAM.  It differs from a pipe in numerous
		details as needed to support logging.

if RAMLOG
config RAMLOG_CRLF
	bool "RAMLOG CR/LF"
	default y
	---help---
		Pre-pend a carriage return before every linefeed that goes into the
		RAM log.

config RAMLOG_NONBLOCKING
	bool "RAMLOG non-block reads"
	default y
	---help---
		Reading from the RAMLOG will never block if the RAMLOG is empty.  If the RAMLOG
		is empty, then zero is returned (usually interpreted as end-of-file).

config RAMLOG_POLLTHRESHOLD
	int "The threshold value of circular buffer to notify poll waiters"
	default 1
	---help---
		When the length of circular buffer exceeds the threshold value, the poll() will
		return POLLIN to all poll waiters.
endif

config SYSLOG_BUFFER
	bool "Use buffered output"
	default n
	---help---
		Enables an buffering logic that will be used to serialize debug
		output from concurrent tasks. This enables allocation of one buffer
		per thread, each of size CONFIG_IOB_BUFSIZE.

		The use of SYSLOG buffering is optional.  If not enabled, however,
		then the output from multiple tasks that attempt to generate SYSLOG
		output may be interleaved and difficult to read.

if SYSLOG_BUFFER

config SYSLOG_BUFSIZE
	int "Syslog buffer size"
	default 64
	---help---
		The size of the syslog buffer in bytes.

endif

config SYSLOG_INTBUFFER
	bool "Use interrupt buffer"
	default n
	---help---
		Enables an interrupt buffer that will be used to serialize debug
		output from interrupt handlers.

config SYSLOG_INTBUFSIZE
	int "Interrupt buffer size"
	default 512
	depends on SYSLOG_INTBUFFER
	---help---
		The size of the interrupt buffer in bytes.

comment "Formatting options"

config SYSLOG_TIMESTAMP
	bool "Prepend timestamp to syslog message"
	default n
	---help---
		Prepend timestamp to syslog message.

config SYSLOG_TIMESTAMP_REALTIME
	bool "Use wall-clock for syslog timestamp"
	default n
	depends on SYSLOG_TIMESTAMP
	---help---
		Use wall-clock (CLOCK_REALTIME) for timestamp.  By default,
		CLOCK_MONOTONIC will be used.

config SYSLOG_TIMESTAMP_FORMATTED
	bool "Formatted syslog time"
	default n
	depends on SYSLOG_TIMESTAMP_REALTIME
	---help---
		Syslog timestamp will be formatted according to the
		SYSLOG_TIMESTAMP_FORMAT format string.

config SYSLOG_TIMESTAMP_LOCALTIME
	bool "Use local-time timestamp"
	default n
	depends on SYSLOG_TIMESTAMP_FORMATTED
	---help---
		If selected local time will be used for the timestamps.
		Else, timestamps will be in UTC.

config SYSLOG_TIMESTAMP_FORMAT
	string "Time format"
	default "%d/%m/%y %H:%M:%S"
	depends on SYSLOG_TIMESTAMP_FORMATTED
	---help---
		Formatter string for syslog timestamp printing.
		Uses the standard "strftime" format specifiers.

config SYSLOG_TIMESTAMP_FORMAT_MICROSECOND
	bool "Append microseconds after seconds"
	default y
	depends on SYSLOG_TIMESTAMP_FORMAT = "%d/%m/%y %H:%M:%S"

config SYSLOG_TIMESTAMP_BUFFER
	int "Formatted timestamp buffer size"
	default 64
	depends on SYSLOG_TIMESTAMP_FORMATTED
	---help---
		Buffer size to store syslog formatted timestamps.

config SYSLOG_PRIORITY
	bool "Prepend priority to syslog message"
	default n
	---help---
		Prepend log priority (severity) to syslog message.

config SYSLOG_PROCESS_NAME
	bool "Prepend process name to syslog message"
	default n
	depends on TASK_NAME_SIZE > 0
	---help---
		Prepend Process name to syslog message.

config SYSLOG_PROCESSID
	bool "Prepend process ID to syslog message"
	default n
	---help---
		Prepend Process ID to syslog message.

config SYSLOG_PREFIX
	bool "Prepend prefix to syslog message"
	default n
	---help---
		Prepend prefix to syslog message.

config SYSLOG_PREFIX_STRING
	string "Prefix string"
	depends on SYSLOG_PREFIX
	---help---
		The prefix string to be prepend.

config SYSLOG_COLOR_OUTPUT
	bool "Colored syslog output"
	default n
	---help---
		Enables colored output in syslog, according to message priority.

comment "SYSLOG channels"

config SYSLOG_DEVPATH
	string "System log device"
	default "/dev/kmsg" if RAMLOG_SYSLOG
	default "/dev/ttyS1" if !RAMLOG_SYSLOG
	---help---
		The full path to the system logging device.  For the RAMLOG SYSLOG device,
		this is normally "/dev/kmsg".  For character SYSLOG devices, it should be
		some other existing character device (or file) supported by the configuration
		(such as "/dev/ttyS1")/

if !ARCH_SYSLOG
config SYSLOG_CHAR
	bool "Log to a character device"
	default n
	---help---
		Enable the generic character device for the SYSLOG. The full path to the
		SYSLOG device is provided by SYSLOG_DEVPATH. A valid character device (or
		file) must exist at this path.  It will by opened by syslog_initialize.

config RAMLOG_SYSLOG
	bool "Use RAMLOG for SYSLOG"
	depends on RAMLOG
	default n
	---help---
		Use the RAM logging device for the syslogging interface.  If this
		feature is enabled (along with SYSLOG), then all debug output (only)
		will be re-directed to the circular buffer in RAM.  This RAM log can
		be viewed from NSH using the 'dmesg' command.

config SYSLOG_RPMSG
	bool "Log to RPMSG"
	depends on RPMSG
	depends on SCHED_WORKQUEUE
	default n
	---help---
		Use the RPMSG as a SYSLOG output device, send message to remote proc.

config SYSLOG_STREAM
	bool "Log to stream"
	default n
	---help---
		Enables support to use stream as syslog backend, such as block out stream.
		It is recommended to implement the backend stream in a way that syslog
		works in interrupt context.

config SYSLOG_CONSOLE
	bool "Log to /dev/console"
	default !ARCH_LOWPUTC && !SYSLOG_CHAR && !RAMLOG_SYSLOG && !SYSLOG_RPMSG && !SYSLOG_RTT
	depends on DEV_CONSOLE
	---help---
		Use the system console as a SYSLOG output device.

config SYSLOG_DEFAULT
	bool "Default SYSLOG device"
	default ARCH_LOWPUTC && !SYSLOG_CHAR && !RAMLOG_SYSLOG && !SYSLOG_RPMSG && !SYSLOG_RTT && !SYSLOG_CONSOLE
	---help---
		syslog() interfaces will be present, but all output will go to the
		up_putc(ARCH_LOWPUTC == y) or bit-bucket(ARCH_LOWPUTC == n).

endif

if RAMLOG_SYSLOG

config RAMLOG_BUFFER_SECTION
	string "The section where ramlog buffer is located"
	---help---
		The section where ramlog buffer is located.
		The section shall not be initialized on system boot.

config RAMLOG_BUFSIZE
	int "RAMLOG buffer size"
	default 1024
	---help---
		Size of the console RAM log.  Default: 1024

endif # RAMLOG_SYSLOG

if SYSLOG_RPMSG

config SYSLOG_RPMSG_SERVER_NAME
	string "The name of Syslog RPMSG Server"
	---help---
		The proc name of RPMSG server. Client sends message to
		specified name of remote proc.

config SYSLOG_RPMSG_WORK_DELAY
	int "SYSLOG RPMSG work delay(ms)"
	default 100

config SYSLOG_RPMSG_CHARDEV
	bool "SYSLOG RPMSG character device"
	default SYSLOG_RPMSG_WORK_DELAY != 0

endif # SYSLOG_RPMSG

config SYSLOG_RPMSG_SERVER
	bool "Enable RPMSG server for SYSLOG"
	default n
	depends on RPMSG
	---help---
		Use RPMSG to receive message from remote proc.

config SYSLOG_RPMSG_SERVER_CHARDEV
	bool "SYSLOG RPMSG server character device"
	default n

menuconfig SYSLOG_FILE
	bool "Syslog file output"
	default n
	---help---
		Build in support to use a file to collect SYSLOG output.  File SYSLOG
		channels differ from other SYSLOG channels in that they cannot be
		established until after fully booting and mounting the target file
		system.  The function syslog_file_channel() would need to be called
		from board-specific bring-up logic AFTER mounting the file system
		containing 'devpath'.

		NOTE interrupt level SYSLOG output will be lost in this case unless
		the interrupt buffer is used.

if SYSLOG_FILE

config SYSLOG_FILE_SEPARATE
	bool "Log file separation"
	default n
	---help---
		If enabled, every time the file logger is re-attached, a separator
		will be printed in the file.

		This can be useful to easily distinguish between log entries that
		belong to different log sessions (e.g. system reboot), and to
		indicate that between the separated lines there may be more logs
		that were lost.

config SYSLOG_FILE_ROTATIONS
	int "Log file rotations"
	default 0
	---help---
		If enabled (set to a non-zero number), the log file size will be
		checked before opening. If it is larger than the specified limit
		it will be "rotated", i.e. the old file will be kept as a backup,
		and a new empty	file will be created.

		The number of rotations specifies the number of old log files to
		keep.

		This option is useful to ensure that log files do not get
		huge after prolonged periods of system operation.

config SYSLOG_FILE_SIZE_LIMIT
	int "Log file size limit"
	default 524288
	depends on SYSLOG_FILE_ROTATIONS > 0
	---help---
		File size limit when the log is rotated automatically.
		If a log file is found larger than this limit, it will
		be rotated.

endif # SYSLOG_FILE

config CONSOLE_SYSLOG
	bool "Use SYSLOG for /dev/console"
	default n
	depends on DEV_CONSOLE && !SYSLOG_CONSOLE
	---help---
		Use the syslog logging device as a system console. If this feature is
		enabled (along with DEV_CONSOLE), then all console output will be
		re-directed to syslog output (syslog_putc). This is useful, for
		example, if the only console is a Telnet console.  Then in that case,
		console output from non-Telnet threads will go to the syslog output.

config SYSLOG_CHARDEV
	bool "SYSLOG character device"
	default n
	---help---
		Enables support for a simple character driver at /dev/log whose
		write() method will transfer data to the SYSLOG device.  This can be
		useful if, for example, you want to redirect the output of a program
		to the SYSLOG.

		NOTE that unlike other syslog output, this data is unformatted raw
		byte output with no time-stamping or any other SYSLOG features
		supported.

config SYSLOG_IOCTL
	bool "SYSLOG IOCTL support"
	default n
	---help---
		Enables support for the SYSLOG IOCTL command.  This command is used
		to control the behavior of the SYSLOG device. Currently, the supported
		commands are SYSLOGIOC_SETFILTER/SYSLOGIOC_GETCHANNELS, which can be
		used to set the enable status of different channels

endmenu # System logging