/**************************************************************************** * boards/mips/pic32mx/pic32mx7mmb/include/board.h * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ #ifndef __BOARDS_MIPS_PIC32MX_PIC32MX7MMB_INCLUDE_BOARD_H #define __BOARDS_MIPS_PIC32MX_PIC32MX7MMB_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Configuration ************************************************************/ /* Clocking *****************************************************************/ /* Crystal frequencies */ #define BOARD_POSC_FREQ 8000000 /* Primary OSC XTAL frequency (8MHz) */ #define BOARD_SOSC_FREQ 32768 /* Secondary OSC XTAL frequency (32.768KHz) */ /* Oscillator modes */ #define BOARD_FNOSC_POSCPLL 1 /* Use primary oscillator w/PLL */ #define BOARD_POSC_XTMODE 1 /* Resonator, crystal or resonator (XT) mode */ #undef BOARD_POSC_SWITCH /* Use FRC until POSC stabilizes, then switch */ #undef BOARD_POSC_FSCM /* Switch to FRC if POSC fails */ #define BOARD_SOSC_ENABLE 1 /* Enable Secondary Oscillator */ #define BOARD_SOSC_IESO 1 /* Internal External Switchover mode is enabled */ /* PLL configuration and resulting CPU clock. * CPU_CLOCK = ((POSC_FREQ / IDIV) * MULT) / ODIV */ #define BOARD_PLL_INPUT BOARD_POSC_FREQ #define BOARD_PLL_IDIV 2 /* PLL input divider */ #define BOARD_PLL_MULT 20 /* PLL multiplier */ #define BOARD_PLL_ODIV 1 /* PLL output divider */ #define BOARD_CPU_CLOCK 80000000 /* CPU clock (80MHz = 8MHz * 20 / 2) */ /* USB PLL configuration. * USB_CLOCK = ((POSC_XTAL / IDIV) * 24) / 2 */ #define BOARD_UPLL_IDIV 2 /* USB PLL divider (revisit) */ #define BOARD_USB_CLOCK 48000000 /* USB clock (8MHz / 2) * 24 / 2) */ /* Peripheral clock is divided down from CPU clock. * PBCLOCK = CPU_CLOCK / PBDIV */ #define BOARD_PBDIV 2 /* Peripheral clock divisor (PBDIV) */ #define BOARD_PBCLOCK 40000000 /* Peripheral clock (PBCLK = 80MHz/2) */ /* Watchdog pre-scaler (re-visit) */ #define BOARD_WD_ENABLE 0 /* Watchdog is disabled */ #define BOARD_WD_PRESCALER 8 /* Watchdog pre-scaler */ /* Ethernet MII clocking. * * The clock divider used to create the MII Management Clock (MDC). The MIIM * module uses the SYSCLK as an input clock. According to the IEEE 802.3 * Specification this should be no faster than 2.5 MHz. However, some PHYs * support clock rates up to 12.5 MHz. */ #define BOARD_EMAC_MIIM_DIV 32 /* Ideal: 80MHz/32 = 2.5MHz */ /* LED definitions **********************************************************/ /* LED Configuration ********************************************************/ /* The Mikroelektronika PIC32MX7 MMB has 3 user LEDs labeled LED0-2 in the * schematics: * * --- ----- -------------------------------------------------------------- * PIN Board Notes * --- ----- -------------------------------------------------------------- * RA0 LED0 Pulled-up, low value illuminates * RA1 LED1 Pulled-up, low value illuminates * RD9 LED2 Pulled-up, low value illuminates * RA9 LED4 Not available for general use*, indicates MMC/SD activity * --- LED5 Not controllable by software, indicates power-on * * * RA9 is also the SD chip select. It will illuminate whenever the SD card * is selected. If SD is not used, then LED4 could also be used as a user- * controlled LED. */ /* LED index values for use with board_userled() */ #define PIC32MX_PIC32MX7MMB_LED0 0 #define PIC32MX_PIC32MX7MMB_LED1 1 #define PIC32MX_PIC32MX7MMB_LED2 2 #define PIC32MX_PIC32MX7MMB_NLEDS 3 /* LED bits for use with board_userled_all() */ #define PIC32MX_PIC32MX7MMB_LED0_BIT (1 << PIC32MX_PIC32MX7MMB_LED0) #define PIC32MX_PIC32MX7MMB_LED1_BIT (1 << PIC32MX_PIC32MX7MMB_LED1) #define PIC32MX_PIC32MX7MMB_LED2_BIT (1 << PIC32MX_PIC32MX7MMB_LED2) /* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 3 LEDs * on board the Mikroelektronika PIC32MX7 MMB. The following definitions * describe how NuttX controls the LEDs: * * ON OFF * ------------------------- ---- ---- ---- ---- ---- ---- * LED0 LED1 LED2 LED0 LED1 LED2 * ------------------------- ---- ---- ---- ---- ---- ---- * LED_STARTED 0 OFF OFF OFF --- --- --- * LED_HEAPALLOCATE 1 ON OFF N/C --- --- --- * LED_IRQSENABLED 2 OFF ON N/C --- --- --- * LED_STACKCREATED 3 ON ON N/C --- --- --- * LED_INIRQ 4 N/C N/C ON N/C N/C OFF * LED_SIGNAL 4 N/C N/C ON N/C N/C OFF * LED_ASSERTION 4 N/C N/C ON N/C N/C OFF * LED_PANIC 5 ON N/C N/C OFF N/C N/C */ #define LED_STARTED 0 #define LED_HEAPALLOCATE 1 #define LED_IRQSENABLED 2 #define LED_STACKCREATED 3 #define LED_INIRQ 4 #define LED_SIGNAL 4 #define LED_ASSERTION 4 #define LED_PANIC 5 #define LED_NVALUES 6 /* Switch definitions *******************************************************/ /* The Mikroelektronika PIC32MX7 MMB has a joystick: * * ------ -------- -------------------------- * GPIO SIGNAL BOARD CONNECTION * ------ -------- -------------------------- * RB0 JOY-A Joystick A, HDR1 pin 24 * RB2 JOY-C Joystick C, HDR1 pin 22 * RB1 JOY-B Joystick B, HDR1 pin 23 * RB3 JOY-D Joystick D, HDR1 pin 21 * RA10 JOY-CP Joystick CP, HDR1 pin 25 */ /**************************************************************************** * Public Types ****************************************************************************/ #ifndef __ASSEMBLY__ /**************************************************************************** * Inline Functions ****************************************************************************/ #ifdef __cplusplus #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /**************************************************************************** * Public Function Prototypes ****************************************************************************/ #undef EXTERN #ifdef __cplusplus } #endif #endif /* __ASSEMBLY__ */ #endif /* __BOARDS_MIPS_PIC32MX_PIC32MX7MMB_INCLUDE_BOARD_H */