# # For a description of the syntax of this configuration file, # see the file kconfig-language.txt in the NuttX tools repository. # menu "Timer Driver Support" menuconfig TIMER bool "Timer Support" default n ---help--- This selection enables building of the "upper-half" timer driver. See include/nuttx/timers/timer.h for further timer driver information. menuconfig RTC bool "RTC Driver Support" default n ---help--- This selection enables configuration of a real time clock (RTCdriver. See include/nuttx/timers/rtc.h for further RTC driver information. Most RTC drivers are MCU specific and may require other specific settings. if RTC config RTC_DATETIME bool "Date/Time RTC Support" default n ---help--- There are two general types of RTC: (1) A simple battery backed counter that keeps the time when power is down, and (2) a full date / time RTC the provides the date and time information, often in BCD format. If RTC_DATETIME is selected, it specifies this second kind of RTC. In this case, the RTC is used to "seed" the normal NuttX timer and the NuttX system timer provides for higher resolution time. if !RTC_DATETIME config RTC_HIRES bool "Hi-Res RTC Support" default n ---help--- If RTC_DATETIME not selected, then the simple, battery backed counter is used. There are two different implementations of such simple counters based on the time resolution of the counter: The typical RTC keeps time to resolution of 1 second, usually supporting a 32-bit time_t value. In this case, the RTC is used to "seed" the normal NuttX timer and the NuttX timer provides for higherresoution time. If RTC_HIRES is enabled in the NuttX configuration, then the RTC provides higher resolution time and completely replaces the system timer for purpose of date and time. config RTC_FREQUENCY int "Hi-Res RTC frequency" default 1 depends on RTC_HIRES ---help--- If RTC_HIRES is defined, then the frequency of the high resolution RTC must be provided. If RTC_HIRES is not defined, RTC_FREQUENCY is assumed to be one Hz. endif # !RTC_DATETIME config RTC_ALARM bool "RTC Alarm Support" default n ---help--- Enable if the RTC hardware supports setting of an alarm. A callback function will be executed when the alarm goes off. config RTC_NALARMS int "Number of alarms" default 1 depends on RTC_ALARM ---help--- Number of alarms supported by the hardware. config RTC_DRIVER bool "RTC Driver Support" default n ---help--- This selection enables building of the "upper-half" RTC driver. See include/nuttx/timers/rtc.h for further RTC driver information. if RTC_DRIVER config RTC_PERIODIC bool "RTC Periodic Interrupts" default n depends on EXPERIMENTAL ---help--- Add interrupt controls for RTCs that support periodic interrupts. config RTC_ONESEC bool "RTC Once-per-second interrupts" default n depends on EXPERIMENTAL ---help--- Add interrupt controls for RTCs that support once-per-second interrupts. config RTC_EPOCHYEAR bool "RTC epoch year" default n depends on EXPERIMENTAL ---help--- Add controls for RTCs that support epoch year settings. Many RTCs encode the year in an 8-bit register which is either interpreted as an 8-bit binary number or as a BCD number. In both cases, the number is interpreted relative to this RTC's Epoch. The RTC's Epoch is initialized to 1900 on most systems but on Alpha and MIPS it might also be initialized to 1952, 1980, or 2000, depending on the value of an RTC register for the year. With some RTCs, these operations can be used to read or to set the RTC's Epoch, respectively. config RTC_IOCTL bool "RTC IOCTLs" default n ---help--- Support the RTC interface ioctl() method. This allows you to add architecture-specific RTC operations to the RTC interface endif # RTC_DRIVER config RTC_EXTERNAL bool "External RTC Support" default n ---help--- In modern MCUs, the RTC is usually implement as an internal peripheral to the MCU. An option is to use an external RTC connected to the MCU typically via SPI or I2C. If an external RTC is connect to the MCU through some bus, then the RTC will not be available to the system until after the system fully boots up and is able to access the bus. In that case, this setting must be included to suppress attempts to initialize the RTC early in the boot sequence. config RTC_DSXXXX bool "DS130x/DS323x RTC Driver" default n select I2C select I2C_TRANSFER select RTC_DATETIME depends on RTC_EXTERNAL ---help--- Enables support for the Maxim Integrated DS3231 I2C RTC timer. if RTC_DSXXXX choice prompt "Maxim Integrated RTC" default RTC_DS3231 config RTC_DS1302 bool "DS1302" ---help--- Enables support for the Maxim Integrated DS1307 serial RTC timer. config RTC_DS1307 bool "DS1307" ---help--- Enables support for the Maxim Integrated DS1307 I2C RTC timer. config RTC_DS3231 bool "DS3231" ---help--- Enables support for the Maxim Integrated DS3231 I2C RTC timer. config RTC_DS3232 bool "DS3232" ---help--- Enables support for the Maxim Integrated DS3232 I2C RTC timer. config RTC_DS3234 bool "DS3234" depends on EXPERIMENTAL ---help--- Enables support for the Maxim Integrated DS3234 SPI RTC timer. Not yet implemented. endchoice # Maxim Integrated RTC config DS3231_I2C_FREQUENCY int "DS1307/DS323x I2C frequency" default 400000 range 1 400000 endif # RTC_DSXXXX config RTC_PCF85263 bool "PCF85263 RTC Driver" default n select I2C select I2C_TRANSFER select RTC_DATETIME depends on RTC_EXTERNAL ---help--- Enables support for the Maxim Integrated DS3231 I2C RTC timer. if RTC_PCF85263 config PCF85263_I2C_FREQUENCY int "PCF85263 I2C frequency" default 400000 range 1 400000 endif # RTC_PCF85263 endif # RTC menuconfig WATCHDOG bool "Watchdog Timer Support" default n ---help--- This selection enables building of the "upper-half" watchdog timer driver. See include/nuttx/timers/watchdog.h for further watchdog timer driver information. if WATCHDOG config WATCHDOG_DEVPATH string "Watchdog Device Path" default "/dev/watchdog0" endif # WATCHDOG config TIMERS_CS2100CP bool "CS2100-CP Fraction-N Clock Multiplier" depends on I2C select I2C_TRANSFER if TIMERS_CS2100CP config CS2100CP_DEBUG bool "Enable CS2100-CP Debug Features" depends on DEBUG_FEATURES config CS2100CP_REGDEBUG bool "Enable CS2100-CP Register Debug" depends on DEBUG_FEATURES endif # TIMERS_CS2100CP endmenu # Timer Driver Support