/****************************************************************************
 * boards/arm/s32k1xx/s32k146evb/include/board.h
 *
 * Licensed to the Apache Software Foundation (ASF) under one or more
 * contributor license agreements.  See the NOTICE file distributed with
 * this work for additional information regarding copyright ownership.  The
 * ASF licenses this file to you under the Apache License, Version 2.0 (the
 * "License"); you may not use this file except in compliance with the
 * License.  You may obtain a copy of the License at
 *
 *   http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
 * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
 * License for the specific language governing permissions and limitations
 * under the License.
 *
 ****************************************************************************/

#ifndef __BOARDS_ARM_S32K1XX_S32K146EVB_INCLUDE_BOARD_H
#define __BOARDS_ARM_S32K1XX_S32K146EVB_INCLUDE_BOARD_H

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>

/****************************************************************************
 * Pre-processor Definitions
 ****************************************************************************/

/* Clocking *****************************************************************/

/* The S32K146EVB is fitted with a 8 MHz crystal */

#define BOARD_XTAL_FREQUENCY  8000000

/* The S32K146 will run at 80 MHz in RUN mode */

#define S32K146EVB_RUN_SYSCLK_FREQUENCY  80000000

/* LED definitions **********************************************************/

/* The S32K146EVB has one RGB LED:
 *
 *   RedLED    PTD15  (FTM0 CH0)
 *   GreenLED  PTD16  (FTM0 CH1)
 *   BlueLED   PTD0   (FTM0 CH2)
 *
 * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
 * any way.  The following definitions are used to access individual RGB
 * components.
 *
 * The RGB components could, alternatively be controlled through PWM using
 * the common RGB LED driver.
 */

/* LED index values for use with board_userled() */

#define BOARD_LED_R       0
#define BOARD_LED_G       1
#define BOARD_LED_B       2
#define BOARD_NLEDS       3

/* LED bits for use with board_userled_all() */

#define BOARD_LED_R_BIT   (1 << BOARD_LED_R)
#define BOARD_LED_G_BIT   (1 << BOARD_LED_G)
#define BOARD_LED_B_BIT   (1 << BOARD_LED_B)

/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the LEDs on board
 * the S32K146EVB.  The following definitions describe how NuttX controls the
 * LEDs:
 *
 *      SYMBOL            Meaning                         LED state
 *                                                        RED    GREEN  BLUE
 *      ----------------  -----------------------------  -------------------
 */

#define LED_STARTED       1 /* NuttX has been started     OFF    OFF    OFF */
#define LED_HEAPALLOCATE  2 /* Heap has been allocated    OFF    OFF    ON  */
#define LED_IRQSENABLED   0 /* Interrupts enabled         OFF    OFF    ON  */
#define LED_STACKCREATED  3 /* Idle stack created         OFF    ON     OFF */
#define LED_INIRQ         0 /* In an interrupt           (No change)        */
#define LED_SIGNAL        0 /* In a signal handler       (No change)        */
#define LED_ASSERTION     0 /* An assertion failed       (No change)        */
#define LED_PANIC         4 /* The system has crashed     FLASH  OFF    OFF */
#undef  LED_IDLE            /* S32K146 is in sleep mode  (Not used)         */

/* Button definitions *******************************************************/

/* The S32K146EVB supports two buttons:
 *
 *   SW2  PTC12
 *   SW3  PTC13
 */

#define BUTTON_SW2        0
#define BUTTON_SW3        1
#define NUM_BUTTONS       2

#define BUTTON_SW2_BIT    (1 << BUTTON_SW2)
#define BUTTON_SW3_BIT    (1 << BUTTON_SW3)

/* UART selections **********************************************************/

/* By default, the serial console will be provided on the OpenSDA VCOM port:
 *
 *   OpenSDA UART RX  PTC6  (LPUART1_RX)
 *   OpenSDA UART TX  PTC7  (LPUART1_TX)
 */

#define PIN_LPUART1_RX    PIN_LPUART1_RX_1   /* PTC6 */
#define PIN_LPUART1_TX    PIN_LPUART1_TX_1   /* PTC7 */

/* SPI selections ***********************************************************/

/* UJA1169TK/F SBC SPI  (LPSPI1) */

#define PIN_LPSPI1_SCK    PIN_LPSPI1_SCK_2   /* PTB14 */
#define PIN_LPSPI1_MISO   PIN_LPSPI1_SIN_1   /* PTB15 */
#define PIN_LPSPI1_MOSI   PIN_LPSPI1_SOUT_2  /* PTB16 */
#define PIN_LPSPI1_PCS    PIN_LPSPI1_PCS3    /* PTB17 */

/* CAN selections ***********************************************************/

/* UJA1169TK/F SBC CAN  (CAN0) */

#define PIN_CAN0_RX       PIN_CAN0_RX_4      /* PTE4 */
#define PIN_CAN0_TX       PIN_CAN0_TX_4      /* PTE5 */

#endif /* __BOARDS_ARM_S32K1XX_S32K146EVB_INCLUDE_BOARD_H */