/****************************************************************************
* drivers/audio/wm8904.h
*
* Copyright (C) 2014 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Reference:
* "WM8904 Ultra Low Power CODEC for Portable Audio Applications, Pre-
* Production", September 2012, Rev 3.3, Wolfson Microelectronics
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#ifndef __DRIVERS_AUDIO_WM8904_H
#define __DRIVERS_AUDIO_WM8904_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <pthread.h>
#include <mqueue.h>
#include <nuttx/wqueue.h>
#include <nuttx/fs/ioctl.h>
#ifdef CONFIG_AUDIO
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* So far, I have not been able to get FLL lock interrupts. Worse, I have
* been able to get the FLL to claim that it is locked at all even when
* polling. What am I doing wrong?
*
* Hmmm.. seems unnecessary anyway
*/
#undef WM8904_USE_FFLOCK_INT
#undef WM8904_USE_FFLOCK_POLL
/* Registers Addresses ******************************************************/
#define WM8904_SWRST 0x00 /* SW Reset and ID */
#define WM8904_ID 0x00 /* SW Reset and ID */
#define WM8904_BIAS_CTRL 0x04 /* Bias Control */
#define WM8904_VMID_CTRL 0x05 /* VMID Control */
#define WM8904_MIC_BIAS_CTRL0 0x06 /* Mic Bias Control 0 */
#define WM8904_MIC_BIAS_CTRL1 0x07 /* Mic Bias Control 1 */
#define WM8904_ANALOG_ADC 0x0a /* Analogue ADC */
#define WM8904_PM0 0x0c /* Power Management 0 */
#define WM8904_PM2 0x0e /* Power Management 2 */
#define WM8904_PM3 0x0f /* Power Management 3 */
#define WM8904_PM6 0x12 /* Power Management 6 */
#define WM8904_CLKRATE0 0x14 /* Clock Rates 0 */
#define WM8904_CLKRATE1 0x15 /* Clock Rates 1 */
#define WM8904_CLKRATE2 0x16 /* Clock Rates 2 */
#define WM8904_AIF0 0x18 /* Audio Interface 0 */
#define WM8904_AIF1 0x19 /* Audio Interface 1 */
#define WM8904_AIF2 0x1a /* Audio Interface 2 */
#define WM8904_AIF3 0x1b /* Audio Interface 3 */
#define WM8904_DAC_VOL_LEFT 0x1e /* DAC Digital Volume Left */
#define WM8904_DAC_VOL_RIGHT 0x1f /* DAC Digital Volume Right */
#define WM8904_DAC_DIGI0 0x20 /* DAC Digital 0 */
#define WM8904_DAC_DIGI1 0x21 /* DAC Digital 1 */
#define WM8904_ADC_VOL_LEFT 0x24 /* ADC Digital Volume Left */
#define WM8904_ADC_VOL_RIGHT 0x25 /* ADC Digital Volume Right */
#define WM8904_ADC_DIGI 0x26 /* ADC Digital */
#define WM8904_MIC_DIGI 0x27 /* Digital Microphone */
#define WM8904_DRC0 0x28 /* DRC 0 */
#define WM8904_DRC1 0x29 /* DRC 1 */
#define WM8904_DRC2 0x2a /* DRC 2 */
#define WM8904_DRC3 0x2b /* DRC 3 */
#define WM8904_ANA_LEFT_IN0 0x2c /* Analogue Left Input 0 */
#define WM8904_ANA_RIGHT_IN0 0x2d /* Analogue Right Input 0 */
#define WM8904_ANA_LEFT_IN1 0x2e /* Analogue Left Input 1 */
#define WM8904_ANA_RIGHT_IN1 0x2f /* Analogue Right Input 1 */
#define WM8904_ANA_LEFT_OUT1 0x39 /* Analogue OUT1 Left */
#define WM8904_ANA_RIGHT_OUT1 0x3a /* Analogue OUT1 Right */
#define WM8904_ANA_LEFT_OUT2 0x3b /* Analogue OUT2 Left */
#define WM8904_ANA_RIGHT_OUT2 0x3c /* Analogue OUT2 Right */
#define WM8904_ANA_OUT12_ZC 0x3d /* Analogue OUT12 ZC */
#define WM8904_DC_SERVO0 0x43 /* DC Servo 0 */
#define WM8904_DC_SERVO1 0x44 /* DC Servo 1 */
#define WM8904_DC_SERVO2 0x45 /* DC Servo 2 */
#define WM8904_DC_SERVO4 0x47 /* DC Servo 4 */
#define WM8904_DC_SERVO5 0x48 /* DC Servo 5 */
#define WM8904_DC_SERVO6 0x49 /* DC Servo 6 */
#define WM8904_DC_SERVO7 0x4a /* DC Servo 7 */
#define WM8904_DC_SERVO8 0x4b /* DC Servo 8 */
#define WM8904_DC_SERVO9 0x4c /* DC Servo 9 */
#define WM8904_DC_SERVO_RDBACK 0x4d /* DC Servo Readback 0 */
#define WM8904_ANA_HP0 0x5a /* Analogue HP 0 */
#define WM8904_ANA_LINEOUT0 0x5e /* Analogue Lineout 0 */
#define WM8904_CHG_PUMP0 0x62 /* Charge Pump 0 */
#define WM8904_CLASS_W0 0x68 /* Class W 0 */
#define WM8904_WR_SEQ0 0x6c /* Write Sequencer 0 */
#define WM8904_WR_SEQ1 0x6d /* Write Sequencer 1 */
#define WM8904_WR_SEQ2 0x6e /* Write Sequencer 2 */
#define WM8904_WR_SEQ3 0x6f /* Write Sequencer 3 */
#define WM8904_WR_SEQ4 0x70 /* Write Sequencer 4 */
#define WM8904_FLL_CTRL1 0x74 /* FLL Control 1 */
#define WM8904_FLL_CTRL2 0x75 /* FLL Control 2 */
#define WM8904_FLL_CTRL3 0x76 /* FLL Control 3 */
#define WM8904_FLL_CTRL4 0x77 /* FLL Control 4 */
#define WM8904_FLL_CTRL5 0x78 /* FLL Control 5 */
#define WM8904_GPIO_CTRL1 0x79 /* GPIO Control 1 */
#define WM8904_GPIO_CTRL2 0x7a /* GPIO Control 2 */
#define WM8904_GPIO_CTRL3 0x7b /* GPIO Control 3 */
#define WM8904_GPIO_CTRL4 0x7c /* GPIO Control 4 */
#define WM8904_DIGI_PULLS 0x7e /* Digital Pulls */
#define WM8904_INT_STATUS 0x7f /* Interrupt Status */
#define WM8904_INT_MASK 0x80 /* Interrupt Status Mask */
#define WM8904_INT_POL 0x81 /* Interrupt Polarity */
#define WM8904_INT_DEBOUNCE 0x82 /* Interrupt Debounce */
#define WM8904_EQ1 0x86 /* EQ1 */
#define WM8904_EQ2 0x87 /* EQ2 */
#define WM8904_EQ3 0x88 /* EQ3 */
#define WM8904_EQ4 0x89 /* EQ4 */
#define WM8904_EQ5 0x8a /* EQ5 */
#define WM8904_EQ6 0x8b /* EQ6 */
#define WM8904_EQ7 0x8c /* EQ7 */
#define WM8904_EQ8 0x8d /* EQ8 */
#define WM8904_EQ9 0x8e /* EQ9 */
#define WM8904_EQ10 0x8f /* EQ10 */
#define WM8904_EQ11 0x90 /* EQ11 */
#define WM8904_EQ12 0x91 /* EQ12 */
#define WM8904_EQ13 0x92 /* EQ13 */
#define WM8904_EQ14 0x93 /* EQ14 */
#define WM8904_EQ15 0x94 /* EQ15 */
#define WM8904_EQ16 0x95 /* EQ16 */
#define WM8904_EQ17 0x96 /* EQ17 */
#define WM8904_EQ18 0x97 /* EQ18 */
#define WM8904_EQ19 0x98 /* EQ19 */
#define WM8904_EQ20 0x99 /* EQ20 */
#define WM8904_EQ21 0x9a /* EQ21 */
#define WM8904_EQ22 0x9b /* EQ22 */
#define WM8904_EQ23 0x9c /* EQ23 */
#define WM8904_EQ24 0x9d /* EQ24 */
#define WM8904_CTRLIF_TEST_1 0xa1 /* Control Interface Test 1 */
#define WM8904_ADC_TEST 0xc6 /* ADC Test */
#define WM8904_ANA_OUT_BIAS_0 0xCC /* Analogue Output Bias 0 */
#define WM8904_FLL_NCO_TEST0 0xf7 /* FLL NCO Test 0 */
#define WM8904_FLL_NCO_TEST1 0xf8 /* FLL NCO Test 1 */
#define WM8904_DUMMY 0xff /* Dummy register address */
/* Register Default Values **************************************************/
/* Registers have some undocumented bits set on power up. These probably
* should be retained on writes (?).
*/
#define WM8904_SWRST_DEFAULT 0x8904
#define WM8904_ID_DEFAULT 0x0018
#define WM8904_BIAS_CTRL_DEFAULT 0x0000
#define WM8904_VMID_CTRL_DEFAULT 0x0000
#define WM8904_MIC_BIAS_CTRL0_DEFAULT 0x0000
#define WM8904_MIC_BIAS_CTRL1_DEFAULT 0x0000
#define WM8904_ANALOG_ADC_DEFAULT 0x0001
#define WM8904_PM0_DEFAULT 0x0000
#define WM8904_PM2_DEFAULT 0x0000
#define WM8904_PM3_DEFAULT 0x0000
#define WM8904_PM6_DEFAULT 0x0000
#define WM8904_CLKRATE0_DEFAULT 0x8c5e
#define WM8904_CLKRATE1_DEFAULT 0x0c05
#define WM8904_CLKRATE2_DEFAULT 0x0000
#define WM8904_AIF0_DEFAULT 0x0050
#define WM8904_AIF1_DEFAULT 0x000a
#define WM8904_AIF2_DEFAULT 0x00e4
#define WM8904_AIF3_DEFAULT 0x0040
#define WM8904_DAC_VOL_LEFT_DEFAULT 0x00c0
#define WM8904_DAC_VOL_RIGHT_DEFAULT 0x00c0
#define WM8904_DAC_DIGI0_DEFAULT 0x0000
#define WM8904_DAC_DIGI1_DEFAULT 0x0004
#define WM8904_ADC_VOL_LEFT_DEFAULT 0x00c0
#define WM8904_ADC_VOL_RIGHT_DEFAULT 0x00c0
#define WM8904_ADC_DIGI_DEFAULT 0x0010
#define WM8904_MIC_DIGI_DEFAULT 0x0000
#define WM8904_DRC0_DEFAULT 0x01af
#define WM8904_DRC1_DEFAULT 0x3248
#define WM8904_DRC2_DEFAULT 0x0000
#define WM8904_DRC3_DEFAULT 0x0000
#define WM8904_ANA_LEFT_IN0_DEFAULT 0x0085
#define WM8904_ANA_RIGHT_IN0_DEFAULT 0x0085
#define WM8904_ANA_LEFT_IN1_DEFAULT 0x0044
#define WM8904_ANA_RIGHT_IN1_DEFAULT 0x0044
#define WM8904_ANA_LEFT_OUT1_DEFAULT 0x002d
#define WM8904_ANA_RIGHT_OUT1_DEFAULT 0x002d
#define WM8904_ANA_LEFT_OUT2_DEFAULT 0x0039
#define WM8904_ANA_RIGHT_OUT2_DEFAULT 0x0039
#define WM8904_ANA_OUT12_ZC_DEFAULT 0x0000
#define WM8904_DC_SERVO0_DEFAULT 0x0000
#define WM8904_DC_SERVO2_DEFAULT 0xaaaa
#define WM8904_DC_SERVO4_DEFAULT 0xaaaa
#define WM8904_DC_SERVO5_DEFAULT 0xaaaa
#define WM8904_DC_SERVO6_DEFAULT 0x0000
#define WM8904_DC_SERVO7_DEFAULT 0x0000
#define WM8904_DC_SERVO8_DEFAULT 0x0000
#define WM8904_DC_SERVO9_DEFAULT 0x0000
#define WM8904_DC_SERVO_RDBACK_DEFAULT 0x0000
#define WM8904_ANA_HP0_DEFAULT 0x0000
#define WM8904_ANA_LINEOUT0_DEFAULT 0x0000
#define WM8904_CHG_PUMP0_DEFAULT 0x0000
#define WM8904_CLASS_W0_DEFAULT 0x0000
#define WM8904_WR_SEQ0_DEFAULT 0x0000
#define WM8904_WR_SEQ1_DEFAULT 0x0000
#define WM8904_WR_SEQ2_DEFAULT 0x0000
#define WM8904_WR_SEQ3_DEFAULT 0x0000
#define WM8904_WR_SEQ4_DEFAULT 0x0000
#define WM8904_FLL_CTRL1_DEFAULT 0x0000
#define WM8904_FLL_CTRL2_DEFAULT 0x0007
#define WM8904_FLL_CTRL3_DEFAULT 0x0000
#define WM8904_FLL_CTRL4_DEFAULT 0x2ee0
#define WM8904_FLL_CTRL5_DEFAULT 0x0004
#define WM8904_GPIO_CTRL1_DEFAULT 0x0014
#define WM8904_GPIO_CTRL2_DEFAULT 0x0010
#define WM8904_GPIO_CTRL3_DEFAULT 0x0010
#define WM8904_GPIO_CTRL4_DEFAULT 0x0000
#define WM8904_DIGI_PULLS_DEFAULT 0x0000
#define WM8904_INT_MASK_DEFAULT 0xffff
#define WM8904_INT_POL_DEFAULT 0x0000
#define WM8904_INT_DEBOUNCE_DEFAULT 0x0000
#define WM8904_EQ1_DEFAULT 0x0000
#define WM8904_EQ2_DEFAULT 0x000c
#define WM8904_EQ3_DEFAULT 0x000c
#define WM8904_EQ4_DEFAULT 0x000c
#define WM8904_EQ5_DEFAULT 0x000c
#define WM8904_EQ6_DEFAULT 0x000c
#define WM8904_EQ7_DEFAULT 0x0fca
#define WM8904_EQ8_DEFAULT 0x0400
#define WM8904_EQ9_DEFAULT 0x00d8
#define WM8904_EQ10_DEFAULT 0x1eb5
#define WM8904_EQ11_DEFAULT 0xf145
#define WM8904_EQ12_DEFAULT 0x0b75
#define WM8904_EQ13_DEFAULT 0x01c5
#define WM8904_EQ14_DEFAULT 0x1c54
#define WM8904_EQ15_DEFAULT 0xf373
#define WM8904_EQ16_DEFAULT 0x0a54
#define WM8904_EQ17_DEFAULT 0x0558
#define WM8904_EQ18_DEFAULT 0x168e
#define WM8904_EQ19_DEFAULT 0xf829
#define WM8904_EQ20_DEFAULT 0x07ad
#define WM8904_EQ21_DEFAULT 0x1103
#define WM8904_EQ22_DEFAULT 0x0564
#define WM8904_EQ23_DEFAULT 0x0559
#define WM8904_EQ24_DEFAULT 0x4000
#define WM8904_CTRLIF_TEST_1_DEFAULT 0x0000
#define WM8904_FLL_NCO_TEST0_DEFAULT 0x0000
#define WM8904_ANA_OUT_BIAS_0_DEFAULT 0x0000
#define WM8904_ADC_TEST_DEFAULT 0x0000
#define WM8904_FLL_NCO_TEST1_DEFAULT 0x0019
/* Register Bit Definitions *************************************************/
/* 0x00 SW Reset and ID */
#define WM8904_SW_RST_DEV_ID1 0x8904
/* 0x04 Bias Control */
#define WM8904_ISEL_SHIFT (2) /* Bits 2-3: Master Bias Control */
#define WM8904_ISEL_MASK (3 << WM8904_ISEL_SHIFT)
# define WM8904_ISEL_LOW (0 << WM8904_ISEL_SHIFT) /* Low power bias */
# define WM8904_ISEL_HIGH (2 << WM8904_ISEL_SHIFT) /* High performance bias */
#define WM8904_BIAS_ENA (1 << 0) /* Bit 0: Normal bias current generator */
/* 0x05 VMID Control */
#define WM8904_VMID_BUF_ENA (1 << 6) /* Bit 6: Enable VMID buffer to unused I/O */
#define WM8904_VMID_RES_SHIFT (1) /* Bits 1-2: VMID divider enable and select */
#define WM8904_VMID_RES_MASK (3 << WM8904_VMID_RES_SHIFT)
# define WM8904_VMID_RES_OFF (0 << WM8904_VMID_RES_SHIFT) /* VMID disabled */
# define WM8904_VMID_RES_NORMAL (1 << WM8904_VMID_RES_SHIFT) /* 2 x 50k divider */
# define WM8904_VMID_RES_STANDBY (2 << WM8904_VMID_RES_SHIFT) /* 2 x 250k divider */
# define WM8904_VMID_RES_FASTSTART (3 << WM8904_VMID_RES_SHIFT) /* 2 x 5k divider */
#define WM8904_VMID_ENA (1 << 0) /* Bit 0: VMID buffer enable */
/* 0x06 Mic Bias Control 0 */
#define WM8904_MICDET_THR_SHIFT (4) /* Bits 4-6: MICBIAS current detect threshold */
#define WM8904_MICDET_THR_MASK (7 << WM8904_MICDET_THR_SHIFT)
# define WM8904_MICDET_THR(n) ((uint16_t)(n) << WM8904_MICDET_THR_SHIFT)
#define WM8904_MICSHORT_THR_SHIFT (2) /* Bits 2-3: MICBIAS short circuit threshold */
#define WM8904_MICSHORT_THR_MASK (3 << WM8904_MICSHORT_THR_SHIFT)
#define WM8904_MICSHORT_THR(n) ((uint16_t)(n) << WM8904_MICSHORT_THR_SHIFT)
#define WM8904_MICDET_ENA (1 << 1) /* Bit 1: MICBIAS current/short circuit detect enable */
#define WM8904_MICBIAS_ENA (1 << 0) /* Bit 0: MICBIAS enable */
/* 0x07 Mic Bias Control 1 */
#define WM8904_MICBIAS_SEL_MASK (0x0007) /* Bits 0-2: Selects MICBIAS voltage */
/* 0x0a Analogue ADC */
#define WM8904_ADC_OSR128 (1 << 0) /* Bit 0: ADC Oversampling Ratio */
/* 0x0c Power Management 0 */
#define WM8904_INL_ENA (1 << 1) /* Bit 1: Left input PGA enable */
#define WM8904_INR_ENA (1 << 0) /* Bit 0: Right input PGA enable */
/* 0x0e Power Management 2 */
#define WM8904_HPL_PGA_ENA (1 << 1) /* Bit 1: Left headphone output enable */
#define WM8904_HPR_PGA_ENA (1 << 0) /* Bit 0: Right headphone output enable */
/* 0x0f Power Management 3 */
#define WM8904_LINEOUTL_PGA_ENA (1 << 1) /* Bit 1: Left line output enable */
#define WM8904_LINEOUTR_PGA_ENA (1 << 0) /* Bit 0: Right line output enable */
/* 0x12 Power Management 6 */
#define WM8904_DACL_ENA (1 << 3) /* Bit 3: Left DAC enable */
#define WM8904_DACR_ENA (1 << 2) /* Bit 2: Right DAC enable */
#define WM8904_ADCL_ENA (1 << 1) /* Bit 1: Left ADC enable */
#define WM8904_ADCR_ENA (1 << 0) /* Bit 0: Right ADC enable */
/* 0x14 Clock Rates 0 */
#define WM8904_TOCLK_RATE_DIV16 (1 << 14) /* Bit 14: TOCLK Rate Divider (/16) */
#define WM8904_TOCLK_RATE_X4 (1 << 13) /* Bit 13: TOCLK Rate Multiplier */
#define WM8904_MCLK_DIV (1 << 0) /* Bit 0: Enables divide by 2 on MCLK */
# define WM8904_MCLK_DIV1 (0) /* 0: SYSCLK = MCLK */
# define WM8904_MCLK_DIV2 (1 << 0) /* 1: SYSCLK = MCLK/2*/
/* 0x15 Clock Rates 1 */
#define WM8904_CLK_SYS_RATE_SHIFT (10) /* Bits 10-13: Selects the SYSCLK / fs ratio */
#define WM8904_CLK_SYS_RATE_MASK (15 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV64 (0 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV128 (1 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV192 (2 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV256 (3 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV384 (4 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV512 (5 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV768 (6 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV1024 (7 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV1408 (8 << WM8904_CLK_SYS_RATE_SHIFT)
# define WM8904_CLK_SYS_RATE_DIV1536 (9 << WM8904_CLK_SYS_RATE_SHIFT)
#define WM8904_SAMPLE_RATE_SHIFT (0) /* Bits 0-2: Selects the Sample Rate (fs) */
#define WM8904_SAMPLE_RATE_MASK (3 << WM8904_SAMPLE_RATE_SHIFT)
# define WM8904_SAMPLE_RATE_8KHZ (0 << WM8904_SAMPLE_RATE_SHIFT) /* 8kHz */
# define WM8904_SAMPLE_RATE_12KHZ (1 << WM8904_SAMPLE_RATE_SHIFT) /* 11.025kHz, 12kHz */
# define WM8904_SAMPLE_RATE_16KHZ (2 << WM8904_SAMPLE_RATE_SHIFT) /* 16kHz */
# define WM8904_SAMPLE_RATE_24KHZ (3 << WM8904_SAMPLE_RATE_SHIFT) /* 22.05kHz, 24kHz */
# define WM8904_SAMPLE_RATE_32KHZ (4 << WM8904_SAMPLE_RATE_SHIFT) /* 32kHz */
# define WM8904_SAMPLE_RATE_48KHZ (5 << WM8904_SAMPLE_RATE_SHIFT) /* 44.1kHz, 48kHz */
/* 0x16 Clock Rates 2 */
#define WM8904_MCLK_INV (1 << 15) /* Bit 15: MCLK invert */
#define WM8904_SYSCLK_SRC (1 << 14) /* Bit 14: SYSCLK source select */
# define WM8904_SYSCLK_SRCMCLK (0) /* 0: MCLK */
# define WM8904_SYSCLK_SRCFLL (1 << 14) /* 1: FLL Output */
#define WM8904_TOCLK_RATE (1 << 12) /* Bit 12: TOCLK rate divider (/2) */
#define WM8904_OPCLK_ENA (1 << 3) /* Bit 3: GPIO clock output enable */
#define WM8904_CLK_SYS_ENA (1 << 2) /* Bit 2: System clock enable */
#define WM8904_CLK_DSP_ENA (1 << 1) /* Bit 1: DSP clock enable */
#define WM8904_TOCLK_ENA (1 << 0) /* Bit 0: Zero cross timeout enable */
/* 0x18 Audio Interface 0 */
#define WM8904_DACL_DATINV (1 << 12) /* Bit 12: Left DAC invert */
#define WM8904_DACR_DATINV (1 << 11) /* Bit 11: Right DAC invert */
#define WM8904_DAC_BOOST_SHIFT (9) /* Bits 9-10: DAC digital input volume boost */
#define WM8904_DAC_BOOST_MASK (3 << WM8904_DAC_BOOST_SHIFT)
# define WM8904_DAC_BOOST_0DB (0 << WM8904_DAC_BOOST_SHIFT)
# define WM8904_DAC_BOOST_6DB (1 << WM8904_DAC_BOOST_SHIFT)
# define WM8904_DAC_BOOST_12DB (2 << WM8904_DAC_BOOST_SHIFT)
#define WM8904_LOOPBACK (1 << 8) /* Bit 8: Digital loopback function */
#define WM8904_AIFADCL_SRC (1 << 7) /* Bit 7: Left digital audio channel source */
#define WM8904_AIFADCR_SRC (1 << 6) /* Bit 6: Right digital audio channel source */
#define WM8904_AIFDACL_SRC (1 << 5) /* Bit 5: Left DAC data source select */
#define WM8904_AIFDACR_SRC (1 << 4) /* Bit 4: Right DAC data source select */
#define WM8904_ADC_COMP (1 << 3) /* Bit 3: ADC companding enable */
#define WM8904_ADC_COMPMODE (1 << 2) /* Bit 2: ADC companding type */
#define WM8904_DAC_COMP (1 << 1) /* Bit 1: DAC companding enable */
#define WM8904_DAC_COMPMODE (1 << 0) /* Bit 0: DAC companding type */
/* 0x19 Audio Interface 1 */
#define WM8904_AIFDAC_TDM (1 << 13) /* Bit 13: DAC TDM enable */
#define WM8904_AIFDAC_TDM_CHAN (1 << 12) /* Bit 12: DACDAT TDM channel select */
#define WM8904_AIFADC_TDM (1 << 11) /* Bit 11: ADC TDM enable */
#define WM8904_AIFADC_TDM_CHAN (1 << 10) /* Bit 10: ADCDAT TDM channel select */
#define WM8904_AIF_TRIS (1 << 8) /* Bit 8: Audio interface tristate */
#define WM8904_AIF_BCLK_INV (1 << 7) /* Bit 7: BCLK invert */
#define WM8904_BCLK_DIR (1 << 6) /* Bit 6: Audio interface BCLK direction */
#define WM8904_AIF_LRCLK_INV (1 << 4) /* Bit 4: LRC polarity/DSP mode A-B select */
#define WM8904_AIF_WL_SHIFT (2) /* Bits 2-3: Digital audio interface word length */
#define WM8904_AIF_WL_MASK (3 << WM8904_AIF_WL_SHIFT)
# define WM8904_AIF_WL_16BITS (0 << WM8904_AIF_WL_SHIFT)
# define WM8904_AIF_WL_20BITS (1 << WM8904_AIF_WL_SHIFT)
# define WM8904_AIF_WL_24BITS (2 << WM8904_AIF_WL_SHIFT)
# define WM8904_AIF_WL_32BITS (3 << WM8904_AIF_WL_SHIFT)
#define WM8904_AIF_FMT_SHIFT (0) /* Bits 0-1: Digital audio interface format */
#define WM8904_AIF_FMT_MASK (3 << WM8904_AIF_FMT_SHIFT)
# define WM8904_AIF_FMT_RJUST (0 << WM8904_AIF_FMT_SHIFT) /* Right Justified */
# define WM8904_AIF_FMT_LJUST (1 << WM8904_AIF_FMT_SHIFT) /* Left Justified */
# define WM8904_AIF_FMT_I2S (2 << WM8904_AIF_FMT_SHIFT) /* I2S */
# define WM8904_AIF_FMT_DSP (3 << WM8904_AIF_FMT_SHIFT) /* DSP */
/* 0x1a Audio Interface 2 */
#define WM8904_OPCLK_DIV_SHIFT (8) /* Bits 8-11: GPIO Output Clock Divider */
#define WM8904_OPCLK_DIV_MASK (15 << WM8904_OPCLK_DIV_SHIFT)
# define WM8904_OPCLK_DIV1 (0 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK */
# define WM8904_OPCLK_DIV2 (1 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK / 2 */
# define WM8904_OPCLK_DIV3 (2 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK / 3 */
# define WM8904_OPCLK_DIV4 (3 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK / 4 */
# define WM8904_OPCLK_DIV5p5 (4 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK / 5.5 */
# define WM8904_OPCLK_DIV6 (5 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK / 6 */
# define WM8904_OPCLK_DIV8 (6 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK / 8 */
# define WM8904_OPCLK_DIV12 (7 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK / 12 */
# define WM8904_OPCLK_DIV16 (8 << WM8904_OPCLK_DIV_SHIFT) /* SYSCLK / 16 */
#define WM8904_BCLK_DIV_SHIFT (0) /* Bits 0-4: BCLK Frequency (Master Mode) */
#define WM8904_BCLK_DIV_MASK (31 << WM8904_BCLK_DIV_SHIFT)
# define WM8904_BCLK_DIV(n) ((uint16_t)(n) << WM8904_BCLK_DIV_SHIFT)
# define WM8904_BCLK_DIV1 (0 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK */
# define WM8904_BCLK_DIV1p5 (1 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 1.5 */
# define WM8904_BCLK_DIV2 (2 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 2 */
# define WM8904_BCLK_DIV3 (3 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 3 */
# define WM8904_BCLK_DIV4 (4 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 4 */
# define WM8904_BCLK_DIV5 (5 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 5 */
# define WM8904_BCLK_DIV5p5 (6 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 5.5 */
# define WM8904_BCLK_DIV6 (7 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 6 */
# define WM8904_BCLK_DIV8 (8 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 8 */
# define WM8904_BCLK_DIV10 (9 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 10 */
# define WM8904_BCLK_DIV11 (10 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 11 */
# define WM8904_BCLK_DIV12 (11 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 12 */
# define WM8904_BCLK_DIV16 (12 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 16 */
# define WM8904_BCLK_DIV20 (13 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 20 */
# define WM8904_BCLK_DIV22 (14 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 22 */
# define WM8904_BCLK_DIV24 (15 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 24 */
# define WM8904_BCLK_DIV25 (16 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 25 */
# define WM8904_BCLK_DIV30 (17 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 30 */
# define WM8904_BCLK_DIV32 (18 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 32 */
# define WM8904_BCLK_DIV44 (19 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 44 */
# define WM8904_BCLK_DIV48 (20 << WM8904_BCLK_DIV_SHIFT) /* SYSCLK / 48 */
/* 0x1b Audio Interface 3 */
#define WM8904_LRCLK_DIR (1 << 11) /* Bit 11: Audio interface LRC direction */
#define WM8904_LRCLK_RATE_SHIFT (0) /* Bits 0-10: LRC rate (master mode) */
#define WM8904_LRCLK_RATE_MASK (0x7ff << WM8904_LRCLK_RATE_SHIFT)
# define WM8904_LRCLK_RATE(n) ((uint16_t)(n) << WM8904_LRCLK_RATE_SHIFT)
/* 0x1e DAC Digital Volume Left */
/* 0x1f DAC Digital Volume Right */
#define WM8904_DAC_VU (1 << 8) /* Bit 8: DAC volume update */
#define WM8904_DAC_VOL_SHIFT (0) /* Bits 0-7: DAC digital volume */
#define WM8904_DAC_VOL_MASK (0xff << WM8904_DAC_VOL_SHIFT)
# define WM8904_DAC_VOL(n) ((uint16_t)(n) << WM8904_DAC_VOL_SHIFT)
/* 0x20 DAC Digital 0 */
#define WM8904_ADCL_DAC_SVOL_SHIFT (8) /* Bits 8-11: Left digital sidetone volume */
#define WM8904_ADCL_DAC_SVOL_MASK (15 << WM8904_ADCL_DAC_SVOL_SHIFT)
# define WM8904_ADCL_DAC_SVOL(n) ((uint16_t)(n) << WM8904_ADCL_DAC_SVOL_SHIFT)
#define WM8904_ADCR_DAC_SVOL_SHIFT (4) /* Bits 4-7: Right digital sidetone volume*/
#define WM8904_ADCR_DAC_SVOL_MASK (15 << WM8904_ADCR_DAC_SVOL_SHIFT)
# define WM8904_ADCR_DAC_SVOL(n) ((uint16_t)(n) << WM8904_ADCR_DAC_SVOL_SHIFT)
#define WM8904_ADC_TO_DACL_SHIFT (2) /* Bits 2-3: Left DAC digital sidetone source */
#define WM8904_ADC_TO_DACL_MASK (3 << WM8904_ADC_TO_DACL_SHIFT)
# define WM8904_ADC_TO_DACL_NONE (0 << WM8904_ADC_TO_DACL_SHIFT) /* No sidetone */
# define WM8904_ADC_TO_DACL_LEFT (1 << WM8904_ADC_TO_DACL_SHIFT) /* Left ADC */
# define WM8904_ADC_TO_DACL_RIGHT (2 << WM8904_ADC_TO_DACL_SHIFT) /* Right ADC */
#define WM8904_ADC_TO_DACR_SHIFT (0) /* Bits 0-1: Right DAC digital sidetone source */
#define WM8904_ADC_TO_DACR_MASK (3 << WM8904_ADC_TO_DACR_SHIFT)
# define WM8904_ADC_TO_DACR_NONE (0 << WM8904_ADC_TO_DACR_SHIFT) /* No sidetone */
# define WM8904_ADC_TO_DACR_LEFT (1 << WM8904_ADC_TO_DACR_SHIFT) /* Left ADC */
# define WM8904_ADC_TO_DACR_RIGHT (2 << WM8904_ADC_TO_DACR_SHIFT) /* Right ADC */
/* 0x21 DAC Digital 1 */
#define WM8904_DAC_MONO (1 << 12) /* Bit 12: DAC mono mix */
#define WM8904_DAC_SB_FILT (1 << 11) /* Bit 11: Selects DAC filter characteristics */
#define WM8904_DAC_MUTERATE (1 << 10) /* Bit 10: DAC soft mute ramp rate */
#define WM8904_DAC_UNMUTE_RAMP (1 << 9) /* Bit 9: DAC soft mute mode */
#define WM8904_DAC_OSR128 (1 << 6) /* Bit 6: DAC oversample rate select */
#define WM8904_DAC_MUTE (1 << 3) /* Bit 3: DAC soft mute control */
#define WM8904_DEEMPH_SHIFT (1) /* Bits 1-2: DAC de-emphasis control */
#define WM8904_DEEMPH_MASK (3 << WM8904_DEEMPH_SHIFT)
# define WM8904_DEEMPH_NONE (0 << WM8904_DEEMPH_SHIFT) /* No de-emphasis */
# define WM8904_DEEMPH_32KHZ (1 << WM8904_DEEMPH_SHIFT) /* 32kHz sample rate */
# define WM8904_DEEMPH_44p1KHZ (2 << WM8904_DEEMPH_SHIFT) /* 44.1kHz sample rate */
# define WM8904_DEEMPH_48KHZ (3 << WM8904_DEEMPH_SHIFT) /* 48kHz sample rate */
/* 0x24 ADC Digital Volume Left */
/* 0x25 ADC Digital Volume Right */
#define WM8904_ADC_VU (1 << 8) /* Bit 8: ADC Volume Update */
#define WM8904_ADC_VOL_SHIFT (0) /* Bits 0-7: ADC Digital Volume */
#define WM8904_ADC_VOL_MASK (0xff << WM8904_ADC_VOL_SHIFT)
# define WM8904_ADC_VOL(n) ((uint16_t)(n) << WM8904_ADC_VOL_SHIFT)
/* 0x26 ADC Digital */
#define WM8904_ADC_HPF_CUT_SHIFT (5) /* Bits 5-6: ADC digital high pass filter cut-off */
#define WM8904_ADC_HPF_CUT_MASK (3 << WM8904_ADC_HPF_CUT_SHIFT)
# define WM8904_ADC_HPF_CUT_HIFI (0 << WM8904_ADC_HPF_CUT_SHIFT) /* Hi-fi mode */
# define WM8904_ADC_HPF_CUT_VOICE1 (1 << WM8904_ADC_HPF_CUT_SHIFT) /* Voice mode 1 */
# define WM8904_ADC_HPF_CUT_VOICE2 (2 << WM8904_ADC_HPF_CUT_SHIFT) /* Voice mode 2 */
# define WM8904_ADC_HPF_CUT_VOICE3 (3 << WM8904_ADC_HPF_CUT_SHIFT) /* Voice mode 3 */
#define WM8904_ADC_HPF (1 << 4) /* Bit 4: ADC digital high pass filter enable */
#define WM8904_ADCL_DATINV (1 << 1) /* Bit 1: Left ADC invert */
#define WM8904_ADCR_DATINV (1 << 0) /* Bit 0: Right ADC invert */
/* 0x27 Digital Microphone */
#define WM8904_DMIC_ENA (1 << 12) /* Bit 12: Enables digital microphone mode */
#define WM8904_DMIC_SRC (1 << 11) /* Bit 11: Selects digital microphone data input */
/* 0x28 DRC 0 */
#define WM8904_DRC_ENA (1 << 15) /* Bit 15: DRC enable */
#define WM8904_DRC_DAC_PATH (1 << 14) /* Bit 14: DRC path select */
#define WM8904_DRC_GS_HYST_LVL_SHIFT (11) /* Bits 11-12: Gain smoothing hysteresis threshold */
#define WM8904_DRC_GS_HYST_LVL_MASK (3 << WM8904_DRC_GS_HYST_LVL_SHIFT)
# define WM8904_DRC_GS_HYST_LVL(n) ((uint16_t)(n) << WM8904_DRC_GS_HYST_LVL_SHIFT)
# define WM8904_DRC_GS_HYST_LOW (0 << WM8904_DRC_GS_HYST_LVL_SHIFT) /* Low */
# define WM8904_DRC_GS_HYST_MEDIUM (1 << WM8904_DRC_GS_HYST_LVL_SHIFT) /* Medium */
# define WM8904_DRC_GS_HYST_HIGH (2 << WM8904_DRC_GS_HYST_LVL_SHIFT) /* High */
#define WM8904_DRC_STARTUP_GAIN_SHIFT (6) /* Bits 6-10: Initial gain at DRC startup */
#define WM8904_DRC_STARTUP_GAIN_MASK (31 << WM8904_DRC_STARTUP_GAIN_SHIFT)
# define WM8904_DRC_STARTUP_GAIN(n) ((uint16_t)(n) << WM8904_DRC_STARTUP_GAIN_SHIFT)
#define WM8904_DRC_FF_DELAY (1 << 5) /* Bit 5: Feed-forward delay for anti-clip feature */
#define WM8904_DRC_GS_ENA (1 << 3) /* Bit 3: Gain smoothing enable */
#define WM8904_DRC_QR (1 << 2) /* Bit 2: Quick release enable */
#define WM8904_DRC_ANTICLIP (1 << 1) /* Bit 1: Anti-clip enable */
#define WM8904_DRC_GS_HYST (1 << 0) /* Bit 0: Gain smoothing hysteresis enable */
/* 0x29 DRC 1 */
#define WM8904_DRC_ATK_SHIFT (12) /* Bits 13-15: Gain attack rate (seconds/6dB) */
#define WM8904_DRC_ATK_MASK (15 << WM8904_DRC_ATK_SHIFT)
# define WM8904_DRC_ATK(n) ((uint16_t)(n) << WM8904_DRC_ATK_SHIFT)
#define WM8904_DRC_DCY_SHIFT (8) /* Bits 8-11: Gain decay rate (seconds/6dB) */
#define WM8904_DRC_DCY_MASK (15 << WM8904_DRC_DCY_SHIFT)
# define WM8904_DRC_DCY(n) ((uint16_t)(n) << WM8904_DRC_DCY_SHIFT)
#define WM8904_DRC_QR_THR_SHIFT (6) /* Bits 6-7: Quick release crest factor threshold */
#define WM8904_DRC_QR_THR_MASK (3 << WM8904_DRC_QR_THR_SHIFT)
# define WM8904_DRC_QR_THR(n) ((uint16_t)(n) << WM8904_DRC_QR_THR_SHIFT)
#define WM8904_DRC_QR_DCY_SHIFT (4) /* Bits 4-5: Quick release decay rate (seconds/6dB)*/
#define WM8904_DRC_QR_DCY_MASK (3 << WM8904_DRC_QR_DCY_SHIFT)
# define WM8904_DRC_QR_DCY(n) ((uint16_t)(n) << WM8904_DRC_QR_DCY_SHIFT)
#define WM8904_DRC_MINGAIN_SHIFT (2) /* Bits 2-3: Minimum gain the DRC can use to attenuate audio*/
#define WM8904_DRC_MINGAIN_MASK (3 << WM8904_DRC_MINGAIN_SHIFT)
# define WM8904_DRC_MINGAIN(n) ((uint16_t)(n) << WM8904_DRC_MINGAIN_SHIFT)
#define WM8904_DRC_MAXGAIN_SHIFT (0) /* Bits 0-1: Maximum gain the DRC can use to boost audio*/
#define WM8904_DRC_MAXGAIN_MASK (3 << WM8904_DRC_MAXGAIN_SHIFT)
# define WM8904_DRC_MAXGAIN(n) ((uint16_t)(n) << WM8904_DRC_MAXGAIN_SHIFT)
/* 0x2a DRC 2 */
#define WM8904_DRC_HI_COMP_SHIFT (3) /* Bits 3-5: Compressor slope (upper region) */
#define WM8904_DRC_HI_COMP_MASK (7 << WM8904_DRC_HI_COMP_SHIFT)
# define WM8904_DRC_HI_COMP_DIV1 (0 << WM8904_DRC_HI_COMP_SHIFT) /* 1 (no compression) */
# define WM8904_DRC_HI_COMP_DIV2 (1 << WM8904_DRC_HI_COMP_SHIFT) /* 1/2 */
# define WM8904_DRC_HI_COMP_DIV4 (2 << WM8904_DRC_HI_COMP_SHIFT) /* 1/4 */
# define WM8904_DRC_HI_COMP_DIV8 (3 << WM8904_DRC_HI_COMP_SHIFT) /* 1/8 */
# define WM8904_DRC_HI_COMP_DIV16 (4 << WM8904_DRC_HI_COMP_SHIFT) /* 1/16 */
# define WM8904_DRC_HI_COMP_ZERO (5 << WM8904_DRC_HI_COMP_SHIFT) /* 0 */
#define WM8904_DRC_LO_COMP_SHIFT (0) /* Bits 0-2: Compressor slope (lower region)*/
#define WM8904_DRC_LO_COMP_MASK (7 << WM8904_DRC_LO_COMP_SHIFT)
# define WM8904_DRC_LO_COMP(n) ((uint16_t)(n) << WM8904_DRC_LO_COMP_SHIFT)
# define WM8904_DRC_LO_COMP_DIV1 (0 << WM8904_DRC_HI_COMP_SHIFT) /* 1 (no compression) */
# define WM8904_DRC_LO_COMP_DIV2 (1 << WM8904_DRC_HI_COMP_SHIFT) /* 1/2 */
# define WM8904_DRC_LO_COMP_DIV4 (2 << WM8904_DRC_HI_COMP_SHIFT) /* 1/4 */
# define WM8904_DRC_LO_COMP_DIV8 (3 << WM8904_DRC_HI_COMP_SHIFT) /* 1/8 */
# define WM8904_DRC_LO_COMP_DIV16 (4 << WM8904_DRC_HI_COMP_SHIFT) /* 1/16 */
# define WM8904_DRC_LO_COMP_ZERO (5 << WM8904_DRC_HI_COMP_SHIFT) /* 0 */
/* 0x2b DRC 3 */
#define WM8904_DRC_KNEE_IP_SHIFT (5) /* Bits 5-10: Input signal at the compressor knee*/
#define WM8904_DRC_KNEE_IP_MASK (0X3f << WM8904_DRC_KNEE_IP_SHIFT)
# define WM8904_DRC_KNEE_IP(n) ((uint16_t)(n) << WM8904_DRC_KNEE_IP_SHIFT)
#define WM8904_DRC_KNEE_OP_SHIFT (0) /* Bits 0-4: Output signal at the compressor knee */
#define WM8904_DRC_KNEE_OP_MASK (0x1f << WM8904_DRC_KNEE_OP_SHIFT)
# define WM8904_DRC_KNEE_OP(n) ((uint16_t)(n) << WM8904_DRC_KNEE_OP_SHIFT)
/* 0x2c Analogue Left Input 0 */
/* 0x2d Analogue Right Input 0 */
#define WM8904_INMUTE (1 << 7) /* Bit 7: Input PGA mute */
#define WM8904_IN_VOL_SHIFT (0) /* Bits 0-4: Input PGA volume */
#define WM8904_IN_VOL_MASK (31 << WM8904_IN_VOL_SHIFT)
# define WM8904_IN_VOL(n) ((uint16_t)(n) << WM8904_IN_VOL_SHIFT)
/* 0x2e Analogue Left Input 1 */
/* 0x2f Analogue Right Input 1 */
#define WM8904_IN_CM_ENA (1 << 6) /* Bit 6: Input PGA common mode rejection enable */
#define WM8904_IP_SEL_N_SHIFT (4) /* Bits 4-5: Select pin for inverting input */
#define WM8904_IP_SEL_N_MASK (3 << WM8904_IP_SEL_N_SHIFT)
# define WM8904_IP_SEL_N_IN1L (0 << WM8904_IP_SEL_N_SHIFT)
# define WM8904_IP_SEL_N_IN2L (1 << WM8904_IP_SEL_N_SHIFT)
# define WM8904_IP_SEL_N_IN3L (2 << WM8904_IP_SEL_N_SHIFT)
#define WM8904_IP_SEL_P_SHIFT (2) /* Bits 2-3: Select pin for non-inverting input */
#define WM8904_IP_SEL_P_MASK (3 << WM8904_IP_SEL_P_SHIFT)
# define WM8904_IP_SEL_P(n) ((uint16_t)(n) << WM8904_IP_SEL_P_SHIFT)
# define WM8904_IP_SEL_P_IN1L (0 << WM8904_IP_SEL_P_SHIFT)
# define WM8904_IP_SEL_P_IN2L (1 << WM8904_IP_SEL_P_SHIFT)
# define WM8904_IP_SEL_P_IN3L (2 << WM8904_IP_SEL_P_SHIFT)
#define WM8904_MODE_SHIFT (0) /* Bits 0-1: Sets mode for analog input */
#define WM8904_MODE_MASK (23<< WM8904_MODE_SHIFT)
# define WM8904_MODE(n) ((uint16_t)(n) << WM8904_MODE_SHIFT)
# define WM8904_MODE_SINGLE (0 << WM8904_MODE_SHIFT) /* Single-Ended */
# define WM8904_MODE_DIFFLINE (1 << WM8904_MODE_SHIFT) /* Differential Line */
# define WM8904_MODE_DIFFMIC (2 << WM8904_MODE_SHIFT) /* Differential MIC */
/* 0x39 Analogue OUT1 Left */
/* 0x3a Analogue OUT1 Right */
#define WM8904_HPOUT_MUTE (1 << 8) /* Bit 8: Headphone output mute */
#define WM8904_HPOUT_VU (1 << 7) /* Bit 7: Headphone output volume update */
#define WM8904_HPOUTZC (1 << 6) /* Bit 6: Headphone output zero cross enable */
#define WM8904_HPOUT_VOL_SHIFT (0) /* Bits 0-5: Headphone output volume */
#define WM8904_HPOUT_VOL_MASK (0x3f << WM8904_HPOUT_VOL_SHIFT)
# define WM8904_HPOUT_VOL(n) ((uint16_t)(n) << WM8904_HPOUT_VOL_SHIFT)
/* 0x3b Analogue OUT2 Left */
/* 0x3c Analogue OUT2 Right */
#define WM8904_LINEOUT_MUTE (1 << 8) /* Bit 8: Headphone output mute */
#define WM8904_LINEOUT_VU (1 << 7) /* Bit 7: Headphone output volume update */
#define WM8904_LINEOUTZC (1 << 6) /* Bit 6: Headphone output zero cross enable */
#define WM8904_LINEOUT_VOL_SHIFT (0) /* Bits 0-5: Headphone output volume */
#define WM8904_LINEOUT_VOL_MASK (0x3f << WM8904_LINEOUT_VOL_SHIFT)
# define WM8904_LINEOUT_VOL(n) ((uint16_t)(n) << WM8904_LINEOUT_VOL_SHIFT)
/* 0x3d Analogue OUT12 ZC */
#define WM8904_HPL_BYP_ENA (1 << 3) /* Bit 3: Selects input for left headphone output MUX */
#define WM8904_HPR_BYP_ENA (1 << 2) /* Bit 2: Selects input for right headphone output MUX */
#define WM8904_LINEOUTL_BYP_ENA (1 << 1) /* Bit 1: Selects input for left line output MUX */
#define WM8904_LINEOUTR_BYP_ENA (1 << 0) /* Bit 0: Selects input for right line output MUX */
/* 0x43 DC Servo 0 */
#define WM8904_DCS_ENA_CHAN_3 (1 << 3) /* Bit 3: DC servo enable for LINEOUTR */
#define WM8904_DCS_ENA_CHAN_2 (1 << 2) /* Bit 2: DC servo enable for LINEOUTL */
#define WM8904_DCS_ENA_CHAN_1 (1 << 1) /* Bit 1: DC servo enable for HPOUTR */
#define WM8904_DCS_ENA_CHAN_0 (1 << 0) /* Bit 0: DC servo enable for HPOUTL */
/* 0x44 DC Servo 1 */
#define WM8904_DCS_TRIG_SINGLE_3 (1 << 15) /* Bit 15: Single DC offset correction for LINEOUTR */
#define WM8904_DCS_TRIG_SINGLE_2 (1 << 14) /* Bit 14: Single DC offset correction for LINEOUTL */
#define WM8904_DCS_TRIG_SINGLE_1 (1 << 13) /* Bit 13: Single DC offset correction for HPOUTR */
#define WM8904_DCS_TRIG_SINGLE_0 (1 << 12) /* Bit 12: Single DC offset correction for HPOUTL */
#define WM8904_DCS_TRIG_SERIES_3 (1 << 11) /* Bit 11: Series of DC offset corrections for LINEOUTR */
#define WM8904_DCS_TRIG_SERIES_2 (1 << 10) /* Bit 10: Series of DC offset corrections for LINEOUTL */
#define WM8904_DCS_TRIG_SERIES_1 (1 << 9) /* Bit 9: Series of DC offset corrections for HPOUTR */
#define WM8904_DCS_TRIG_SERIES_0 (1 << 8) /* Bit 8: Series of DC offset corrections for HPOUTL */
#define WM8904_DCS_TRIG_STARTUP_3 (1 << 7) /* Bit 7: Start-up DC Servo mode for LINEOUTR */
#define WM8904_DCS_TRIG_STARTUP_2 (1 << 6) /* Bit 6: Start-up DC Servo mode for LINEOUTL */
#define WM8904_DCS_TRIG_STARTUP_1 (1 << 5) /* Bit 5: Start-up DC Servo mode for HPOUTR */
#define WM8904_DCS_TRIG_STARTUP_0 (1 << 4) /* Bit 4: Start-up DC Servo mode for HPOUTL */
#define WM8904_DCS_TRIG_DAC_WR_3 (1 << 3) /* Bit 3: DAC write DC Servo mode for LINEOUTR */
#define WM8904_DCS_TRIG_DAC_WR_2 (1 << 2) /* Bit 2: DAC write DC Servo mode for LINEOUTL */
#define WM8904_DCS_TRIG_DAC_WR_1 (1 << 1) /* Bit 1: DAC write DC Servo mode for HPOUTR */
#define WM8904_DCS_TRIG_DAC_WR_0 (1 << 0) /* Bit 0: DAC write DC Servo mode for HPOUTL */
/* 0x45 DC Servo 2 */
#define WM8904_DCS_TIMER_PERIOD_23_SHIFT (8) /* Bits 8-11: LINEOUTL/LINEOUTR update period */
#define WM8904_DCS_TIMER_PERIOD_23_MASK (15 << WM8904_DCS_TIMER_PERIOD_23_SHIFT)
# define WM8904_DCS_TIMER_PERIOD_23(n) ((uint16_t)(n) << WM8904_DCS_TIMER_PERIOD_23_SHIFT)
#define WM8904_DCS_TIMER_PERIOD_01_SHIFT (0) /* Bits 0-3: HPOUTL/HPOUTR update period */
#define WM8904_DCS_TIMER_PERIOD_01_MASK (15 << WM8904_DCS_TIMER_PERIOD_01_SHIFT)
# define WM8904_DCS_TIMER_PERIOD_01(n) ((uint16_t)(n) << WM8904_DCS_TIMER_PERIOD_01_SHIFT)
/* 0x47 DC Servo 4 */
#define WM8904_DCS_SERIES_NO_23_MASK (0x007f) /* Bits 0-6: Number updates to perform in series for LINEOUTL/R */
/* 0x48 DC Servo 5 */
#define WM8904_DCS_SERIES_NO_01_MASK (0x007f) /* Bits 0-6: Number updates to perform in series for HPOUTL/R */
/* 0x49 DC Servo 6 */
#define WM8904_DCS_DAC_WR_VAL_3_MASK (0x00ff) /* Bits 0-7: DC Offset value for LINEOUTR */
/* 0x4a DC Servo 7 */
#define WM8904_DCS_DAC_WR_VAL_2_MASK (0x00ff) /* Bits 0-7: DC Offset value for LINEOUTL */
/* 0x4b DC Servo 8 */
#define WM8904_DCS_DAC_WR_VAL_1_MASK (0x00ff) /* Bits 0-7: DC Offset value for HPOUTR */
/* 0x4c DC Servo 9 */
#define WM8904_DCS_DAC_WR_VAL_0_MASK (0x00ff) /* Bits 0-7: DC Offset value for HPOUTL */
/* 0x4d DC Servo Readback 0 */
#define WM8904_DCS_CAL_COMPLETE_SHIFT (8) /* Bits 8-11: DC servo complete status */
#define WM8904_DCS_CAL_COMPLETE_MASK (15 << WM8904_DCS_CAL_COMPLETE_SHIFT)
# define WM8904_DCS_CAL_COMPLETE_LINEOUTR (8 << WM8904_DCS_CAL_COMPLETE_SHIFT)
# define WM8904_DCS_CAL_COMPLETE_LINEOUTL (4 << WM8904_DCS_CAL_COMPLETE_SHIFT)
# define WM8904_DCS_CAL_COMPLETE_HPOUTR (2 << WM8904_DCS_CAL_COMPLETE_SHIFT)
# define WM8904_DCS_CAL_COMPLETE_HPOUTL (1 << WM8904_DCS_CAL_COMPLETE_SHIFT)
#define WM8904_DCS_DAC_WR_COMPLETE_SHIFT (4) /* Bits 4-7: DC servo DAC write status */
#define WM8904_DCS_DAC_WR_COMPLETE_MASK (15 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
# define WM8904_DCS_DAC_WR_COMPLETE_LINEOUTR (8 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
# define WM8904_DCS_DAC_WR_COMPLETE_LINEOUTL (4 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
# define WM8904_DCS_DAC_WR_COMPLETE_HPOUTR (2 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
# define WM8904_DCS_DAC_WR_COMPLETE_HPOUTL (1 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
#define WM8904_DCS_STARTUP_COMPLETE_SHIFT (0) /* Bits 0-3: DC servo start-up status */
#define WM8904_DCS_STARTUP_COMPLETE_MASK (15 << WM8904_DCS_STARTUP_COMPLETE_SHIFT)
# define WM8904_DCS_STARTUP_COMPLETE(n) ((uint16_t)(n) << WM8904_DCS_STARTUP_COMPLETE_SHIFT)
# define WM8904_DCS_STARTUP_COMPLETE_LINEOUTR (8 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
# define WM8904_DCS_STARTUP_COMPLETE_LINEOUTL (4 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
# define WM8904_DCS_STARTUP_COMPLETE_HPOUTR (2 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
# define WM8904_DCS_STARTUP_COMPLETE_HPOUTL (1 << WM8904_DCS_DAC_WR_COMPLETE_SHIFT)
/* 0x5a Analogue HP 0 */
#define WM8904_HPL_RMV_SHORT (1 << 7) /* Bit 7: Removes HPOUTL short */
#define WM8904_HPL_ENA_OUTP (1 << 6) /* Bit 6: Enables HPOUTL output stage */
#define WM8904_HPL_ENA_DLY (1 << 5) /* Bit 5: Enables HPOUTL intermediate stage */
#define WM8904_HPL_ENA (1 << 4) /* Bit 4: Enables HPOUTL input stage */
#define WM8904_HPR_RMV_SHORT (1 << 3) /* Bit 3: Removes HPOUTR short */
#define WM8904_HPR_ENA_OUTP (1 << 2) /* Bit 2: Enables HPOUTR output stage */
#define WM8904_HPR_ENA_DLY (1 << 1) /* Bit 1: Enables HPOUTR intermediate stage */
#define WM8904_HPR_ENA (1 << 0) /* Bit 0: Enables HPOUTR input stage */
/* 0x5e Analogue Lineout 0 */
#define WM8904_LINEOUTL_RMV_SHORT (1 << 7) /* Bit 7: Removes LINEOUTL short */
#define WM8904_LINEOUTL_ENA_OUTP (1 << 6) /* Bit 6: Enables LINEOUTL output stage */
#define WM8904_LINEOUTL_ENA_DLY (1 << 5) /* Bit 5: Enables LINEOUTL intermediate stage */
#define WM8904_LINEOUTL_ENA (1 << 4) /* Bit 4: Enables LINEOUTL input stage */
#define WM8904_LINEOUTR_RMV_SHORT (1 << 3) /* Bit 3: Removes LINEOUTR short */
#define WM8904_LINEOUTR_ENA_OUTP (1 << 2) /* Bit 2: Enables LINEOUTR output stage */
#define WM8904_LINEOUTR_ENA_DLY (1 << 1) /* Bit 1: Enables LINEOUTR intermediate stage */
#define WM8904_LINEOUTR_ENA (1 << 0) /* Bit 0: Enables LINEOUTR input stage */
/* 0x62 Charge Pump 0 */
#define WM8904_CP_ENA (1 << 0) /* Bit 0: Enable charge-pump digits */
/* 0x68 Class W 0 */
#define WM8904_CP_DYN_PWR (1 << 0) /* Bit 0: Enable dynamic charge pump power control */
/* 0x6c Write Sequencer 0 */
#define WM8904_WSEQ_ENA (1 << 8) /* Bit 8: Write sequencer enable */
#define WM8904_WSEQ_WRITE_INDEX_SHIFT (0) /* Bits 0-4: Sequence write index */
#define WM8904_WSEQ_WRITE_INDEX_MASK (31 << WM8904_WSEQ_WRITE_INDEX_SHIFT)
# define WM8904_WSEQ_WRITE_INDEX(n) ((uint16_t)(n) << WM8904_WSEQ_WRITE_INDEX_SHIFT)
/* 0x6d Write Sequencer 1 */
#define WM8904_WSEQ_DATA_WIDTH_SHIFT (12) /* Bits 12-14: Width of data block in sequence step */
#define WM8904_WSEQ_DATA_WIDTH_MASK (7 << WM8904_WSEQ_DATA_WIDTH_SHIFT)
# define WM8904_WSEQ_DATA_WIDTH(n) ((uint16_t)((n)-1) << WM8904_WSEQ_DATA_WIDTH_SHIFT)
#define WM8904_WSEQ_DATA_START_SHIFT (8) /* Bits 8-11: LSB bit of data block in sequence step */
#define WM8904_WSEQ_DATA_START_MASK (15 << WM8904_WSEQ_DATA_START_SHIFT)
# define WM8904_WSEQ_DATA_START(n) ((uint16_t)(n) << WM8904_WSEQ_DATA_START_SHIFT)
#define WM8904_WSEQ_ADDR_SHIFT (0) /* Bits 0-7: Control Register be written in sequence step */
#define WM8904_WSEQ_ADDR_MASK (0xff << WM8904_WSEQ_ADDR_SHIFT)
# define WM8904_WSEQ_ADDR(n) ((uint16_t)(n) << WM8904_WSEQ_ADDR_SHIFT)
/* 0x6e Write Sequencer 2 */
#define WM8904_WSEQ_EOS (1 << 14) /* Bit 14: End of sequence flag */
#define WM8904_WSEQ_DELAY_SHIFT (8) /* Bits 8-11: Time delay after executing this step */
#define WM8904_WSEQ_DELAY_MASK (15 << WM8904_WSEQ_DELAY_SHIFT)
# define WM8904_WSEQ_DELAY(n) ((uint16_t)(n) << WM8904_WSEQ_DELAY_SHIFT)
#define WM8904_WSEQ_DATA_SHIFT (0) /* Bits 0-7: Data to be written in this sequence step */
#define WM8904_WSEQ_DATA_MASK (0xff << WM8904_WSEQ_DATA_SHIFT)
# define WM8904_WSEQ_DATA(n) ((uint16_t)(n) << WM8904_WSEQ_DATA_SHIFT)
/* 0x6f Write Sequencer 3 */
#define WM8904_WSEQ_ABORT (1 << 9) /* Bit 9: Aborts the current sequence */
#define WM8904_WSEQ_START (1 << 8) /* Bit 8: Starts the write sequencer */
#define WM8904_WSEQ_START_INDEX_SHIFT (0) /* Bits 0-5: Sequence start index */
#define WM8904_WSEQ_START_INDEX_MASK (63 << WM8904_WSEQ_START_INDEX_SHIFT)
# define WM8904_WSEQ_START_INDEX(n) ((uint16_t)(n) << WM8904_WSEQ_START_INDEX_SHIFT)
/* 0x70 Write Sequencer 4 */
#define WM8904_WSEQ_CURRENT_INDEX_SHIFT (4) /* Bits 4-9: Sequence current index */
#define WM8904_WSEQ_CURRENT_INDEX_MASK (63 << WM8904_WSEQ_CURRENT_INDEX_SHIFT)
#define WM8904_WSEQ_BUSY (1 << 0) /* Bit 0: Sequencer busy flag */
/* 0x74 FLL Control 1 */
#define WM8904_FLL_FRACN_ENA (1 << 2) /* Bit 2: FLL fractional enable */
#define WM8904_FLL_OSC_ENA (1 << 1) /* Bit 1: FLL oscillator enable */
#define WM8904_FLL_ENA (1 << 0) /* Bit 0: FLL enable */
/* 0x75 FLL Control 2 */
#define WM8904_FLL_OUTDIV_SHIFT (8) /* Bits 8-13: FLL FOUT clock divider */
#define WM8904_FLL_OUTDIV_MASK (63 << WM8904_FLL_OUTDIV_SHIFT)
# define WM8904_FLL_OUTDIV(n) ((uint16_t)((n)-1) << WM8904_FLL_OUTDIV_SHIFT)
#define WM8904_FLL_CTRL_RATE_SHIFT (4) /* Bits 4-6: Frequency of the FLL control block */
#define WM8904_FLL_CTRL_RATE_MASK (7 << WM8904_FLL_CTRL_RATE_SHIFT)
# define WM8904_FLL_CTRL_RATE(n) ((uint16_t)((n)-1) << WM8904_FLL_CTRL_RATE_SHIFT)
#define WM8904_FLL_FRATIO_SHIFT (0) /* Bits 0-2: FVCO clock divider */
#define WM8904_FLL_FRATIO_MASK (7 << WM8904_FLL_FRATIO_SHIFT)
# define WM8904_FLL_FRATIO(n) ((uint32_t)(n) << WM8904_FLL_FRATIO_SHIFT)
# define WM8904_FLL_FRATIO_DIV1 (0 << WM8904_FLL_FRATIO_SHIFT) /* Divide by 1 */
# define WM8904_FLL_FRATIO_DIV2 (1 << WM8904_FLL_FRATIO_SHIFT) /* Divide by 2 */
# define WM8904_FLL_FRATIO_DIV4 (2 << WM8904_FLL_FRATIO_SHIFT) /* Divide by 4 */
# define WM8904_FLL_FRATIO_DIV8 (3 << WM8904_FLL_FRATIO_SHIFT) /* Divide by 8 */
# define WM8904_FLL_FRATIO_DIV16 (4 << WM8904_FLL_FRATIO_SHIFT) /* Divide by 16 */
/* 0x76 FLL Control 3, Bits 0-15=Fractional multiply for FREF */
/* 0x77 FLL Control 4 */
#define WM8904_FLL_N_SHIFT (5) /* Bits 5-14: Integer multiply for FREF */
#define WM8904_FLL_N_MASK (0x3ff << WM8904_FLL_N_SHIFT)
# define WM8904_FLL_N(n) ((uint16_t)(n) << WM8904_FLL_N_SHIFT)
#define WM8904_FLL_GAIN_SHIFT (0) /* Bits 0-3: FLL Gain applied to error */
#define WM8904_FLL_GAIN_MASK (15 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X1 (0 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X2 (1 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X4 (2 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X8 (3 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X16 (4 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X32 (5 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X64 (6 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X128 (7 << WM8904_FLL_GAIN_SHIFT)
# define WM8904_FLL_GAIN_X256 (8 << WM8904_FLL_GAIN_SHIFT)
/* 0x78 FLL Control 5 */
#define WM8904_FLL_CLK_REF_DIV_SHIFT (3) /* Bits 3-4: FLL clock reference divider */
#define WM8904_FLL_CLK_REF_DIV_MASK (3 << WM8904_FLL_CLK_REF_DIV_SHIFT)
# define WM8904_FLL_CLK_REF_DIV1 (0 << WM8904_FLL_CLK_REF_DIV_SHIFT) /* MCLK / 1 */
# define WM8904_FLL_CLK_REF_DIV2 (1 << WM8904_FLL_CLK_REF_DIV_SHIFT) /* MCLK / 2 */
# define WM8904_FLL_CLK_REF_DIV4 (2 << WM8904_FLL_CLK_REF_DIV_SHIFT) /* MCLK / 4 */
# define WM8904_FLL_CLK_REF_DIV8 (3 << WM8904_FLL_CLK_REF_DIV_SHIFT) /* MCLK / 8 */
#define WM8904_FLL_CLK_REF_SRC_SHIFT (0) /* Bits 0-2: FLL clock source */
#define WM8904_FLL_CLK_REF_SRC_MASK (3 << WM8904_FLL_CLK_REF_SRC_SHIFT)
# define WM8904_FLL_CLK_REF_SRC_MCLK (0 << WM8904_FLL_CLK_REF_SRC_SHIFT)
# define WM8904_FLL_CLK_REF_SRC_BCLK (1 << WM8904_FLL_CLK_REF_SRC_SHIFT)
# define WM8904_FLL_CLK_REF_SRC_LRCLK (2 << WM8904_FLL_CLK_REF_SRC_SHIFT)
/* 0x79 GPIO Control 1 */
#define WM8904_GPIO1_PU (1 << 5) /* Bit 5: GPIO1 pull-up resistor enable */
#define WM8904_GPIO1_PD (1 << 4) /* Bit 4: GPIO1 pull-down resistor enable */
#define WM8904_GPIO1_SEL_SHIFT (0) /* Bits 0-3: */
#define WM8904_GPIO1_SEL_MASK (15 << WM8904_GPIO1_SEL_SHIFT)
# define WM8904_GPIO1_SEL_INPUT (0 << WM8904_GPIO1_SEL_SHIFT) /* Input pin */
# define WM8904_GPIO1_SEL_CLKOUT (1 << WM8904_GPIO1_SEL_SHIFT) /* Clock output (f=SYSCLK/OPCLKDIV) */
# define WM8904_GPIO1_SEL_ZERO (2 << WM8904_GPIO1_SEL_SHIFT) /* Logic '0' */
# define WM8904_GPIO1_SEL_ONE (3 << WM8904_GPIO1_SEL_SHIFT) /* Logic '1' */
# define WM8904_GPIO1_SEL_IRQ (4 << WM8904_GPIO1_SEL_SHIFT) /* IRQ */
# define WM8904_GPIO1_SEL_FLLLOCK (5 << WM8904_GPIO1_SEL_SHIFT) /* FLL Lock */
# define WM8904_GPIO1_SEL_MICDET (6 << WM8904_GPIO1_SEL_SHIFT) /* Mic Detect */
# define WM8904_GPIO1_SEL_MICSHORT (7 << WM8904_GPIO1_SEL_SHIFT) /* Mic Short */
# define WM8904_GPIO1_SEL_DMICOUT (8 << WM8904_GPIO1_SEL_SHIFT) /* DMIC clock out */
# define WM8904_GPIO1_SEL_FLLOUT (9 << WM8904_GPIO1_SEL_SHIFT) /* FLL Clock Output */
/* 0x7a GPIO Control 2 */
#define WM8904_GPIO2_PU (1 << 5) /* Bit 5: GPIO2 pull-up resistor enable */
#define WM8904_GPIO2_PD (1 << 4) /* Bit 4: GPIO2 pull-down resistor enable */
#define WM8904_GPIO2_SEL_SHIFT (0) /* Bits 0-3: */
#define WM8904_GPIO2_SEL_MASK (15 << WM8904_GPIO2_SEL_SHIFT)
# define WM8904_GPIO2_SEL_INPUT (0 << WM8904_GPIO2_SEL_SHIFT) /* Input pin */
# define WM8904_GPIO2_SEL_CLKOUT (1 << WM8904_GPIO2_SEL_SHIFT) /* Clock output (f=SYSCLK/OPCLKDIV) */
# define WM8904_GPIO2_SEL_ZERO (2 << WM8904_GPIO2_SEL_SHIFT) /* Logic '0' */
# define WM8904_GPIO2_SEL_ONE (3 << WM8904_GPIO2_SEL_SHIFT) /* Logic '1' */
# define WM8904_GPIO2_SEL_IRQ (4 << WM8904_GPIO2_SEL_SHIFT) /* IRQ */
# define WM8904_GPIO2_SEL_FLLLOCK (5 << WM8904_GPIO2_SEL_SHIFT) /* FLL Lock */
# define WM8904_GPIO2_SEL_MICDET (6 << WM8904_GPIO2_SEL_SHIFT) /* Mic Detect */
# define WM8904_GPIO2_SEL_MICSHORT (7 << WM8904_GPIO2_SEL_SHIFT) /* Mic Short */
# define WM8904_GPIO2_SEL_DMICOUT (8 << WM8904_GPIO2_SEL_SHIFT) /* DMIC clock out */
# define WM8904_GPIO2_SEL_FLLOUT (9 << WM8904_GPIO2_SEL_SHIFT) /* FLL Clock Output */
/* 0x7b GPIO Control 3 */
#define WM8904_GPIO3_PU (1 << 5) /* Bit 5: GPIO3 pull-up resistor enable */
#define WM8904_GPIO3_PD (1 << 4) /* Bit 4: GPIO3 pull-down resistor enable */
#define WM8904_GPIO3_SEL_SHIFT (0) /* Bits 0-3: */
#define WM8904_GPIO3_SEL_MASK (15 << WM8904_GPIO3_SEL_SHIFT)
# define WM8904_GPIO3_SEL_INPUT (0 << WM8904_GPIO3_SEL_SHIFT) /* Input pin */
# define WM8904_GPIO3_SEL_CLKOUT (1 << WM8904_GPIO3_SEL_SHIFT) /* Clock output (f=SYSCLK/OPCLKDIV) */
# define WM8904_GPIO3_SEL_ZERO (2 << WM8904_GPIO3_SEL_SHIFT) /* Logic '0' */
# define WM8904_GPIO3_SEL_ONE (3 << WM8904_GPIO3_SEL_SHIFT) /* Logic '1' */
# define WM8904_GPIO3_SEL_IRQ (4 << WM8904_GPIO3_SEL_SHIFT) /* IRQ */
# define WM8904_GPIO3_SEL_FLLLOCK (5 << WM8904_GPIO3_SEL_SHIFT) /* FLL Lock */
# define WM8904_GPIO3_SEL_MICDET (6 << WM8904_GPIO3_SEL_SHIFT) /* Mic Detect */
# define WM8904_GPIO3_SEL_MICSHORT (7 << WM8904_GPIO3_SEL_SHIFT) /* Mic Short */
# define WM8904_GPIO3_SEL_DMICOUT (8 << WM8904_GPIO3_SEL_SHIFT) /* DMIC clock out */
# define WM8904_GPIO3_SEL_FLLOUT (9 << WM8904_GPIO3_SEL_SHIFT) /* FLL Clock Output */
/* 0x7c GPIO Control 4 */
#define WM8904_GPI7_ENA (1 << 9) /* Bit 9: GPI7 input enable */
#define WM8904_GPI8_ENA (1 << 8) /* Bit 8: GPI8 input enable */
#define WM8904_GPIO_BCLK_MODE_ENA (1 << 7) /* Bit 7: Selects BCLK/GPIO4 pin function */
#define WM8904_GPIO_BCLK_SEL_SHIFT (0) /* Bits 0-3: GPIO_BCLK function select */
#define WM8904_GPIO_BCLK_SEL_MASK (15 << WM8904_GPIO_BCLK_SEL_SHIFT)
# define WM8904_GPIO_BCLK_SEL_INPUT (0 << WM8904_GPIO_BCLK_SEL_SHIFT) /* Input pin */
# define WM8904_GPIO_BCLK_SEL_CLKOUT (1 << WM8904_GPIO_BCLK_SEL_SHIFT) /* Clock output (f=SYSCLK/OPCLKDIV) */
# define WM8904_GPIO_BCLK_SEL_ZERO (2 << WM8904_GPIO_BCLK_SEL_SHIFT) /* Logic '0' */
# define WM8904_GPIO_BCLK_SEL_ONE (3 << WM8904_GPIO_BCLK_SEL_SHIFT) /* Logic '1' */
# define WM8904_GPIO_BCLK_SEL_IRQ (4 << WM8904_GPIO_BCLK_SEL_SHIFT) /* IRQ */
# define WM8904_GPIO_BCLK_SEL_FLLLOCK (5 << WM8904_GPIO_BCLK_SEL_SHIFT) /* FLL Lock */
# define WM8904_GPIO_BCLK_SEL_MICDET (6 << WM8904_GPIO_BCLK_SEL_SHIFT) /* Mic Detect */
# define WM8904_GPIO_BCLK_SEL_MICSHORT (7 << WM8904_GPIO_BCLK_SEL_SHIFT) /* Mic Short */
# define WM8904_GPIO_BCLK_SEL_DMICOUT (8 << WM8904_GPIO_BCLK_SEL_SHIFT) /* DMIC clock out */
# define WM8904_GPIO_BCLK_SEL_FLLOUT (9 << WM8904_GPIO_BCLK_SEL_SHIFT) /* FLL Clock Output */
/* 0x7e Digital Pulls */
#define WM8904_MCLK_PU (1 << 7) /* Bit 7: MCLK pull-up resistor enable */
#define WM8904_MCLK_PD (1 << 6) /* Bit 6: MCLK pull-down resistor enable */
#define WM8904_DACDAT_PU (1 << 5) /* Bit 5: DACDAT pull-up resistor enable */
#define WM8904_DACDAT_PD (1 << 4) /* Bit 4: DACDAT pull-down resistor enable */
#define WM8904_LRCLK_PU (1 << 3) /* Bit 3: LRCLK pull-up resistor enable */
#define WM8904_LRCLK_PD (1 << 2) /* Bit 2: LRCLK pull-down resistor enable */
#define WM8904_BCLK_PU (1 << 1) /* Bit 1: BCLK pull-up resistor enable */
#define WM8904_BCLK_PD (1 << 0) /* Bit 0: BCLK pull-down resistor enable */
/* Common interrupt bits */
/* 0x7f Interrupt Status */
/* 0x80 Interrupt Status Mask */
/* 0x81 Interrupt Polarity */
/* 0x82 Interrupt Debounce */
#define WM8904_GPIO_BCLK_INT (1 << 9) /* Bit 9: GPIO4 interrupt */
#define WM8904_WSEQ_INT (1 << 8) /* Bit 8: Write Sequence interrupt */
#define WM8904_GPIO3_INT (1 << 7) /* Bit 7: GPIO3 interrupt */
#define WM8904_GPIO2_INT (1 << 6) /* Bit 6: GPIO2 interrupt */
#define WM8904_GPIO1_INT (1 << 5) /* Bit 5: GPIO1 interrupt */
#define WM8904_GPI8_INT (1 << 4) /* Bit 4: GPI8 interrupt */
#define WM8904_GPI7_INT (1 << 3) /* Bit 3: GPI7 interrupt */
#define WM8904_FLL_LOCK_INT (1 << 2) /* Bit 2: FLL Lock interrupt */
#define WM8904_MIC_SHRT_INT (1 << 1) /* Bit 1: MICBIAS short circuit interrupt */
#define WM8904_MIC_DET_INT (1 << 0) /* Bit 0: MICBIAS short circuit interrupt */
#define WM8904_ALL_INTS (0x03ff)
/* 0x7f Interrupt Status (only) */
#define WM8904_IRQ (1 << 10) /* Bit 10: Logical OR of all other interrupt flags */
/* 0x86 EQ1 */
#define WM8904_EQ_ENA (1 << 0) /* Bit 0: EQ enable */
/* 0x87-0x8b EQ2-EQ6: 5 bit equalizer value */
/* 0x8c-0x9d EQ7-EQ24: 16-bit equalizer value */
/* 0xa1 Control Interface Test 1 */
#define WM8904_USER_KEY 0x0002
/* 0xc6 ADC Test */
#define WM8904_ADC_128_OSR_TST_MODE (1 << 2) /* Bit 2: ADC bias control (1) */
#define WM8904_ADC_BIASX1P5 (1 << 0) /* Bit 0: ADC bias control (2) */
/* 0xcc Analogue Output Bias 0 */
#define WM8904_ANA_OUT_BIAS_SHIFT (4) /* Bits 4-6: */
#define WM8904_ANA_OUT_BIAS_MASK (7 << WM8904_ANA_OUT_BIAS_SHIFT)
# define WM8904_ANA_OUT_BIAS(n) ((uint16_t)(n) << WM8904_ANA_OUT_BIAS_SHIFT)
/* 0xf7 FLL NCO Test 0 */
#define WM8904_FLL_FRC_NCO (1 << 0) /* Bit 0: FLL Forced control select */
/* 0xf8 FLL NCO Test 1 */
#define WM8904FLL_FRC_NCO_SHIFT (0) /* Bits 0-5: FLL forced oscillator value */
#define WM8904FLL_FRC_NCO_MASK (0x3f << WM8904FLL_FRC_NCO_SHIFT)
# define WM8904FLL_FRC_NCO_VAL(n) ((uint16_t)(n) << WM8904FLL_FRC_NCO_SHIFT)
/* FLL Configuration *********************************************************/
/* Default FLL configuration */
#define WM8904_DEFAULT_SAMPRATE 11025 /* Initial sample rate */
#define WM8904_DEFAULT_NCHANNELS 1 /* Initial number of channels */
#define WM8904_DEFAULT_BPSAMP 16 /* Initial bits per sample */
#define WM8904_NFLLRATIO_DIV1 0 /* Values of the FLL_RATIO field */
#define WM8904_NFLLRATIO_DIV2 1
#define WM8904_NFLLRATIO_DIV4 2
#define WM8904_NFLLRATIO_DIV8 3
#define WM8904_NFLLRATIO_DIV16 4
#define WM8904_NFLLRATIO 5 /* Number of FLL_RATIO values */
#define WM8904_MINOUTDIV 4 /* Minimum FLL_OUTDIV divider */
#define WM8904_MAXOUTDIV 64 /* Maximum FLL_OUTDIV divider */
#define WM8904_BCLK_MAXDIV 20 /* Maximum BCLK divider */
#define WM8904_FVCO_MIN 90000000 /* Minimum value of Fvco */
#define WM8904_FVCO_MAX 100000000 /* Maximum value of Fvco */
#define WM8904_FRAMELEN8 14 /* Bits per frame for 8-bit data */
#define WM8904_FRAMELEN16 32 /* Bits per frame for 16-bit data */
/* Commonly defined and redefined macros */
#ifndef MIN
# define MIN(a,b) (((a) < (b)) ? (a) : (b))
#endif
#ifndef MAX
# define MAX(a,b) (((a) > (b)) ? (a) : (b))
#endif
/****************************************************************************
* Public Types
****************************************************************************/
struct wm8904_dev_s
{
/* We are an audio lower half driver (We are also the upper "half" of
* the WM8904 driver with respect to the board lower half driver).
*
* Terminology: Our "lower" half audio instances will be called dev for the
* publicly visible version and "priv" for the version that only this driver
* knows. From the point of view of this driver, it is the board lower
* "half" that is referred to as "lower".
*/
struct audio_lowerhalf_s dev; /* WM8904 audio lower half (this device) */
/* Our specific driver data goes here */
const FAR struct wm8904_lower_s *lower; /* Pointer to the board lower functions */
FAR struct i2c_master_s *i2c; /* I2C driver to use */
FAR struct i2s_dev_s *i2s; /* I2S driver to use */
struct dq_queue_s pendq; /* Queue of pending buffers to be sent */
struct dq_queue_s doneq; /* Queue of sent buffers to be returned */
mqd_t mq; /* Message queue for receiving messages */
char mqname[16]; /* Our message queue name */
pthread_t threadid; /* ID of our thread */
uint32_t bitrate; /* Actual programmed bit rate */
sem_t pendsem; /* Protect pendq */
#ifdef WM8904_USE_FFLOCK_INT
struct work_s work; /* Interrupt work */
#endif
uint16_t samprate; /* Configured samprate (samples/sec) */
#ifndef CONFIG_AUDIO_EXCLUDE_VOLUME
#ifndef CONFIG_AUDIO_EXCLUDE_BALANCE
uint16_t balance; /* Current balance level (b16) */
#endif /* CONFIG_AUDIO_EXCLUDE_BALANCE */
uint8_t volume; /* Current volume level {0..63} */
#endif /* CONFIG_AUDIO_EXCLUDE_VOLUME */
uint8_t nchannels; /* Number of channels (1 or 2) */
uint8_t bpsamp; /* Bits per sample (8 or 16) */
volatile uint8_t inflight; /* Number of audio buffers in-flight */
#ifdef WM8904_USE_FFLOCK_INT
volatile bool locked; /* FLL is locked */
#endif
bool running; /* True: Worker thread is running */
bool paused; /* True: Playing is paused */
bool mute; /* True: Output is muted */
#ifndef CONFIG_AUDIO_EXCLUDE_STOP
bool terminating; /* True: Stop requested */
#endif
bool reserved; /* True: Device is reserved */
volatile int result; /* The result of the last transfer */
};
/****************************************************************************
* Public Data
****************************************************************************/
#ifdef CONFIG_WM8904_CLKDEBUG
extern const uint8_t g_sysclk_scaleb1[WM8904_BCLK_MAXDIV+1];
extern const uint8_t g_fllratio[WM8904_NFLLRATIO];
#endif
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
/****************************************************************************
* Name: wm8904_readreg
*
* Description
* Read the specified 16-bit register from the WM8904 device.
*
****************************************************************************/
#if defined(CONFIG_WM8904_REGDUMP) || defined(CONFIG_WM8904_CLKDEBUG)
struct wm8904_dev_s;
uint16_t wm8904_readreg(FAR struct wm8904_dev_s *priv, uint8_t regaddr);
#endif
#endif /* CONFIG_AUDIO */
#endif /* __DRIVERS_AUDIO_WM8904_H */