#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

if ARCH_BOARD_RDDRONE_BMS772

config S32K1XX_NRSTCHECK_PROCFS
	bool "RDDRONE-BMS772 nRST Check PROCFS entry"
	default n
	depends on FS_PROCFS
	select FS_PROCFS_REGISTER
	---help---
		Self-test to check that the MCU reset pin is connected to an
		external pull-up resistor (or an IC that pulls the pin high).
		The input logic level is registered as a PROCFS entry.

config SMBUS_SBD
	bool "SMBus Smart Battery Data slave"
	default n
	depends on I2C_SLAVE
	---help---
		Simple SMBus/I2C slave providing battery management data,
		specifically implementing a subset of the Smart Battery Data
		Specification, Revision 1.1

menu "RDDRONE-BMS772 PM configuration"
depends on PM

menu "PM configuration for PM_STANDBY mode"

choice
	prompt "MCU power mode"
	default VLPR_STANDBY

config RUN_STANDBY
	bool "RUN mode"
	---help---
		The MCU should be in RUN mode in the PM_STANDBY mode

config VLPR_STANDBY
	bool "VLPR mode"
	---help---
		The MCU should be in VLPR (very low power run) mode in the PM_STANDBY
		mode

endchoice # MCU power mode

menuconfig PM_SPI_STANDBY
	bool "Enable SPI in PM_STANDBY mode"
	default n
	depends on SPI
	---help---
		Enable PM configuration for SPI

if PM_SPI_STANDBY

config PM_SPI0_STANDBY
	bool "Enable LPSPI0 in PM_STANDBY mode"
	default n
	depends on S32K1XX_LPSPI0

config PM_SPI1_STANDBY
	bool "Enable LPSPI1 in PM_STANDBY mode"
	default n
	depends on S32K1XX_LPSPI1

endif # PM_SPI_STANDBY

menuconfig PM_SERIAL_STANDBY
	bool "Enable serial in PM_STANDBY mode"
	default n
	depends on SERIAL
	---help---
		Enable PM configuration for SERIAL

if PM_SERIAL_STANDBY

config PM_CONSOLE_STANDBY
	bool "Enable serial console in PM_STANDBY"
	default n
	depends on SERIAL_CONSOLE
	select PM_SERIAL0_STANDBY if LPUART0_SERIAL_CONSOLE
	select PM_SERIAL1_STANDBY if LPUART1_SERIAL_CONSOLE
	select PM_SERIAL2_STANDBY if LPUART2_SERIAL_CONSOLE

config PM_SERIAL0_STANDBY
	bool "Enable LPUART0 in PM_STANDBY mode"
	default n
	depends on S32K1XX_LPUART0

config PM_SERIAL1_STANDBY
	bool "Enable LPUART1 in PM_STANDBY mode"
	default n
	depends on S32K1XX_LPUART1

config PM_SERIAL2_STANDBY
	bool "Enable LPUART2 in PM_STANDBY mode"
	default n
	depends on S32K1XX_LPUART2

endif # PM_SERIAL_STANDBY

endmenu # PM configuration for PM_STANDBY mode

menu "PM configuration for PM_SLEEP mode"

choice
	prompt "MCU power mode"
	default VLPR_SLEEP

config RUN_SLEEP
	bool "RUN mode"
	---help---
		The MCU should be in RUN mode in the PM_SLEEP mode

config VLPR_SLEEP
	bool "VLPR mode"
	---help---
		The MCU should be in VLPR (very low power run) mode in the PM_SLEEP
		mode

endchoice # MCU power mode

menuconfig PM_SPI_SLEEP
	bool "Enable SPI in PM_SLEEP mode"
	default n
	depends on SPI
	---help---
		Enable PM configuration for SPI

if PM_SPI_SLEEP

menuconfig PM_SPI0_SLEEP
	bool "Enable LPSPI0 in PM_SLEEP"
	default n
	depends on S32K1XX_LPSPI0

menuconfig PM_SPI1_SLEEP
	bool "Enable LPSPI1 in PM_SLEEP"
	default n
	depends on S32K1XX_LPSPI1

endif # PM_SPI_SLEEP

menuconfig PM_SERIAL_SLEEP
	bool "Enable serial in PM_SLEEP mode"
	default n
	depends on SERIAL
	---help---
		Enable PM configuration for SERIAL

if PM_SERIAL_SLEEP

config PM_CONSOLE_SLEEP
	bool "Enable serial console in PM_SLEEP"
	default n
	depends on SERIAL_CONSOLE
	select PM_SERIAL0_SLEEP if LPUART0_SERIAL_CONSOLE
	select PM_SERIAL1_SLEEP if LPUART1_SERIAL_CONSOLE
	select PM_SERIAL2_SLEEP if LPUART2_SERIAL_CONSOLE

config PM_SERIAL0_SLEEP
	bool "Enable LPUART0 in PM_SLEEP mode"
	default n
	depends on S32K1XX_LPUART0

config PM_SERIAL1_SLEEP
	bool "Enable LPUART1 in PM_SLEEP mode"
	default n
	depends on S32K1XX_LPUART1

config PM_SERIAL2_SLEEP
	bool "Enable LPUART2 in PM_SLEEP mode"
	default n
	depends on S32K1XX_LPUART2

endif # PM_SERIAL_SLEEP

endmenu # PM configuration for PM_SLEEP mode

endmenu # RDDRONE-BMS772 PM configuration

endif # ARCH_BOARD_RDDRONE_BMS772