#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

menuconfig NETDEVICES
	bool "Network Device/PHY Support"
	default n if !ARCH_HAVE_PHY
	default y if ARCH_HAVE_PHY
	depends on NET
	---help---
		Network interface driver and PHY selections.  This options enables
		selection of drivers for external Ethernet MAC chips.  The majority
		of MCUs, however, have built-in, internal Ethernet MAC peripherals
		and that Ethernet support is selected in the MCU-specific
		configuration menus.

		Most Ethernet MAC drivers, whether internal or external, will
		require configuration of an external PHY device.  That external PHY
		device is also selected via this menu.

if NETDEVICES

comment "General Ethernet MAC Driver Options"

config NET_RPMSG_DRV
	bool "RPMSG net driver"
	depends on NET && OPENAMP
	select ARCH_HAVE_NETDEV_STATISTICS
	---help---
		Use the rpmsg as net device, transfer packet between remoteproc.

if NET_RPMSG_DRV

config NET_RPMSG_PRIORITY
	int "net prmsg priority"
	default 100
	---help---
		The priority for net rmpsg task.

config NET_RPMSG_STACKSIZE
	int "net rpmsg stack size"
	default DEFAULT_TASK_STACKSIZE
	---help---
		The stack size allocated for the net rpmsg task.

endif # NET_RPMSG_DRV

config NETDEV_TELNET
	bool "Telnet driver"
	default n
	depends on NET && NET_TCP
	---help---
		The Telnet driver generates a character driver instance to support a
		Telnet session.  This driver is used by the Telnet daemon.  The
		Telnet daemon will instantiate a new Telnet driver to support
		standard I/O on the new Telnet session.

if NETDEV_TELNET

config TELNET_RXBUFFER_SIZE
	int "Telnet RX buffer size"
	default 256

config TELNET_TXBUFFER_SIZE
	int "Telnet TX buffer size"
	default 256

config TELNET_MAXLCLIENTS
	int "Maximum Telnet clients"
	default 8
	---help---
		The maximum number of Telnet clients tasks is limited by this
		number.  This limitation is somewhat artificial since it only
		determines the size of a fixed-size, preallocated, internal array.

config TELNET_CHARACTER_MODE
	bool "Character mode"
	default n
	---help---
		The Telnet daemon works in character mode. In this case, the daemon
		will echo a character which telnet client sent. By default, it works
		in line mode.

config TELNET_IOTHREAD_PRIORITY
	int "I/O thread priority"
	default 100

config TELNET_IOTHREAD_STACKSIZE
	int "I/O thread stack size"
	default 1024

config TELNET_SUPPORT_NAWS
	bool "Support NAWS (Negotiate About Window Size)"
	default n

config TELNET_DUMPBUFFER
	bool "Dump Telnet buffers"
	default n
	depends on DEBUG_NET

endif # NETDEV_TELNET

config NETDEV_STATISTICS
	bool "Network device driver statistics"
	depends on NET_STATISTICS && ARCH_HAVE_NETDEV_STATISTICS
	---help---
		Enable to collect statistics from the network drivers (if supported
		by the network driver).

config NET_DUMPPACKET
	bool "Enable packet dumping"
	depends on DEBUG_FEATURES
	default n
	---help---
		Some Ethernet MAC drivers supporting dumping of received and
		transmitted packets as a debug option.  This setting enables that
		debug option. Also needs CONFIG_DEBUG_FEATURES.

comment "External Ethernet MAC Device Support"

menuconfig NET_DM90x0
	bool "Davicom dm9000/dm9010 support"
	default n
	select ARCH_HAVE_NETDEV_STATISTICS
	---help---
		References: Davicom data sheets (DM9000-DS-F03-041906.pdf,
		DM9010-DS-F01-103006.pdf) and looking at lots of other DM90x0
		drivers.

if NET_DM90x0

config DM9X_BASE
	hex "DM90x0 base address"
	default 0x0

config DM9X_IRQ
	int "DM90x0 IRQ number"
	default 0

choice
	prompt "DM90x0 bus width"
	default DM9X_BUSWIDTH16

config DM9X_BUSWIDTH8
	bool "8-bits"

config DM9X_BUSWIDTH16
	bool "16-bits"

config DM9X_BUSWIDTH32
	bool "32-bits"

endchoice # DM90x0 bus width

config DM9X_CHECKSUM
	bool "Checksum enable"
	default n

config DM9X_ETRANS
	bool "TX poll"
	default n

choice
	prompt "DM90x0 mode"
	default DM9X_MODE_AUTO

config DM9X_MODE_AUTO
	bool "Autonegotiation"

config DM9X_MODE_10MHD
	bool "10BaseT half duplex"

config DM9X_MODE_10MFD
	bool "10BaseT full duplex"

config DM9X_MODE_100MHD
	bool "100BaseT half duplex"

config DM9X_MODE_100MFD
	bool "100BaseT full duplex"

endchoice # DM90x0 mode

config DM9X_NINTERFACES
	int "Number of DM90x0 interfaces"
	default 1
	depends on EXPERIMENTAL

endif # NET_DM90x0

menuconfig ENC28J60
	bool "Microchip ENC28J60 support"
	default n
	select SPI
	select ARCH_HAVE_NETDEV_STATISTICS
	---help---
		References:
		ENC28J60 Data Sheet, Stand-Alone Ethernet Controller with SPI Interface,
		DS39662C, 2008 Microchip Technology Inc.

if ENC28J60

config ENC28J60_NINTERFACES
	int "Number of physical ENC28J60"
	default 1
	range 1 1
	---help---
		Specifies the number of physical ENC28J60
		devices that will be supported.

config ENC28J60_SPIMODE
	int "SPI mode"
	default 0
	---help---
		Controls the SPI mode.  The ENC28J60 spec says that it supports SPI
		mode 0,0 only: "The implementation used on this device supports SPI
		mode 0,0 only. In addition, the SPI port requires that SCK be at Idle
		in a low state; selectable clock polarity is not supported."
		However, sometimes you need to tinker with these things.

config ENC28J60_FREQUENCY
	int "SPI frequency"
	default 20000000
	---help---
		Define to use a different bus frequency

config ENC28J60_HALFDUPPLEX
	bool "Enable half dupplex"
	default n
	---help---
		Default is full duplex

config ENC28J60_DUMPPACKET
	bool "Dump Packets"
	default n
	---help---
		If selected, the ENC28J60 driver  will dump the contents of each
		packet to the console.

config ENC28J60_REGDEBUG
	bool "Register-Level Debug"
	default n
	depends on DEBUG_FEATURES && DEBUG_NET
	---help---
		Enable very low-level register access debug.  Depends on
		CONFIG_DEBUG_FEATURES and CONFIG_DEBUG_NET.

endif # ENC28J60

menuconfig ENCX24J600
	bool "Microchip ENCX24J600 support"
	default n
	select SPI
	select ARCH_HAVE_NETDEV_STATISTICS
	---help---
		References:
		ENC424J600/624J600 Data Sheet Stand-Alone 10/100 Ethernet Controller
		with SPI or Parallel Interface DS39935B, 2009 Microchip Technology Inc.

if ENCX24J600

config ENC28J60_NINTERFACES
	int "Number of physical ENCX24J600"
	default 1
	range 1 1
	---help---
		Specifies the number of physical ENCX24J600
		devices that will be supported.

config ENCX24J600_SPIMODE
	int "SPI mode"
	default 0
	---help---
		Controls the SPI mode.  The ENCX24J600 spec says that it supports SPI
		mode 0,0 only: "The implementation used on this device supports SPI
		mode 0,0 only. In addition, the SPI port requires that SCK be at Idle
		in a low state; selectable clock polarity is not supported."
		However, sometimes you need to tinker with these things.

config ENCX24J600_FREQUENCY
	int "SPI frequency"
	default 14000000
	---help---
		Define to use a different bus frequency

config ENCX24J600_NRXDESCR
	int "Descriptor Count"
	default 8
	---help---
		Defines how many descriptors are preallocated for the
		transmission and reception queues.
		The ENC has a relative large packet buffer of 24kB which can
		be used to buffer multiple packets simultaneously

config ENCX24J600_DUMPPACKET
	bool "Dump Packets"
	default n
	---help---
		If selected, the ENCX24J600 driver  will dump the contents of each
		packet to the console.

config ENCX24J600_REGDEBUG
	bool "Register-Level Debug"
	default n
	depends on DEBUG_FEATURES && DEBUG_NET
	---help---
		Enable very low-level register access debug.  Depends on
		CONFIG_DEBUG_FEATURES and CONFIG_DEBUG_NET.

endif # ENCX24J600

menuconfig NET_FTMAC100
	bool "Faraday 10/100 Ethernet"
	default n
	---help---
		Faraday 10/100 Ethernet support.

if NET_FTMAC100

config FTMAC100_BASE
	hex "FTMAC100 base address"
	default 0x0

config FTMAC100_IRQ
	int "FTMAC100 IRQ number"
	default 0

config FTMAC100_RX_DESC
	int "Number of RX descriptors"
	default 64

config FTMAC100_TX_DESC
	int "Number of TX descriptors"
	default 32

config FTMAC100_MAC0_ENV_ADDR
	hex "MAC0 address location"
	default 0

endif # NET_FTMAC100

menuconfig NET_LAN91C111
	bool "Microchip LAN91C111 Support"
	select ARCH_HAVE_NETDEV_STATISTICS
	---help---
		References:
		LAN91C111 Data Sheet, 10/100 Non-PCI Ethernet Single Chip MAC + PHY
		DS00002276A, 2016 Microchip Technology Inc.

if NET_LAN91C111
endif # NET_LAN91C111

if ARCH_HAVE_PHY

comment "External Ethernet PHY Device Support"

choice
	prompt "Board PHY Selection (ETH0)"
	default ETH0_PHY_NONE
	---help---
		Identify the PHY on your board.  This setting is not used by all Ethernet
		drivers nor do all Ethernet drivers support all PHYs.

config ETH0_PHY_NONE
	bool "No PHY support"

config ETH0_PHY_AM79C874
	bool "AMD Am79C874 PHY"

config ETH0_PHY_KS8721
	bool "Micrel KS8721 PHY"

config ETH0_PHY_KSZ8041
	bool "Micrel KSZ8041 PHY"

config ETH0_PHY_KSZ8051
	bool "Micrel KSZ8051 PHY"

config ETH0_PHY_KSZ8061
	bool "Micrel KSZ8061 PHY"

config ETH0_PHY_KSZ8081
	bool "Micrel KSZ8081 PHY"

config ETH0_PHY_KSZ90x1
	bool "Micrel KSZ9021/31 PHY"

config ETH0_PHY_DP83848C
	bool "National Semiconductor DP83848C PHY"

config ETH0_PHY_DP83825I
	bool "Texas Instruments DP83825I PHY"

config ETH0_PHY_TJA1100
	bool "NXP TJA1100 PHY"
	select ARCH_PHY_100BASE_T1

config ETH0_PHY_TJA1101
	bool "NXP TJA1101 PHY"
	select ARCH_PHY_100BASE_T1

config ETH0_PHY_LAN8720
	bool "SMSC LAN8720 PHY"

config ETH0_PHY_LAN8740
	bool "SMSC LAN8740 PHY"

config ETH0_PHY_LAN8740A
	bool "SMSC LAN8740A PHY"

config ETH0_PHY_LAN8742A
	bool "SMSC LAN8742A PHY"

config ETH0_PHY_DM9161
	bool "Davicom DM9161 PHY"

endchoice

choice
	prompt "Board PHY Selection (ETH1)"
	default ETH1_PHY_NONE
	---help---
		Identify the PHY on your board.  This setting is not used by all Ethernet
		drivers nor do all Ethernet drivers support all PHYs.

config ETH1_PHY_NONE
	bool "No PHY support"

config ETH1_PHY_AM79C874
	bool "AMD Am79C874 PHY"

config ETH1_PHY_KS8721
	bool "Micrel KS8721 PHY"

config ETH1_PHY_KSZ8041
	bool "Micrel KSZ8041 PHY"

config ETH1_PHY_KSZ8051
	bool "Micrel KSZ8051 PHY"

config ETH1_PHY_KSZ8081
	bool "Micrel KSZ8081 PHY"

config ETH1_PHY_KSZ90x1
	bool "Micrel KSZ9021/31 PHY"

config ETH1_PHY_DP83848C
	bool "National Semiconductor DP83848C PHY"

config ETH1_PHY_DP83825I
	bool "Texas Instruments DP83825I PHY"

config ETH1_PHY_TJA1100
	bool "NXP TJA1100 PHY"
	select ARCH_PHY_100BASE_T1

config ETH1_PHY_TJA1101
	bool "NXP TJA1101 PHY"
	select ARCH_PHY_100BASE_T1

config ETH1_PHY_LAN8720
	bool "SMSC LAN8720 PHY"

config ETH1_PHY_DM9161
	bool "Davicom DM9161 PHY"

endchoice

config ARCH_PHY_100BASE_T1
	bool
	default n

if (ARCH_PHY_100BASE_T1)

choice
	prompt "Automotive Ethernet 100BASE-T1 master/slave mode"
	default PHY_100BASE_T1_SLAVE
    ---help---
		Automotive Ethernet 100BASE-T1 requires the PHY to be configured
		in either master or slave mode.

config PHY_100BASE_T1_MASTER
	bool "Master"

config PHY_100BASE_T1_SLAVE
	bool "Slave"

endchoice # 100BASE-T1 master/slave mode

endif

config NETDEV_PHY_DEBUG
	bool "PHY debug"
	default n
	depends on DEBUG_FEATURES
	---help---
		Normally debug output is controlled by DEBUG_NET.  However, that
		may generate a LOT of debug output, especially if CONFIG_DEBUG_INFO is
		also selected.  This option is intended to force VERVOSE debug
		output from certain PHY-related even if DEBUG_NET or CONFIG_DEBUG_INFO
		are not selected.  This allows for focused, unit-level debug of
		the NSH network initialization logic.

endif # ARCH_HAVE_PHY

endif # NETDEVICES