NuttX-6.31 ---------- The 98th release of NuttX, Version 6.31, was made on October 28, 2013, and is available for download from the SourceForge website. Note that release consists of two tarballs: nuttx-6.31.tar.gz and apps-6.31.tar.gz. Both may be needed (see the top-level nuttx/README.txt file for build information). Additional new features and extended functionality: * General: - Standardized stack checking logic so the interfaces can be used by common stack monitoring logic. * Audio Subsystem and Audio Drivers: - Ken Pettit has finally released his long awaited audio subsystem. This is a generic audio subsystem that is appropriate for the deeply embedded MCU. Current testing has, however, been focused on the VS1053 CODEC chip. - Ken Pettit's VS1053 audio CODEC driver is now functional. * Networking / Network Drivers - Add the prefix ETH0 to all PHY configuration selections. This will allow us to support to Ethernet MAC drivers with two different PHYs (identified with ETH0 and ETH1). Enabled with CONFIG_NETDEV_MULTINIC. - Add MII/RMII PHY definitions for the Micrel KSZ8051 PHY. - Add GMII/GRMII PHY definitions for the Micrel KSZ9021/31 PHY. - New network-optimized, higher-performance sendfile() implementation from Max Holtzberg. - Added a simple routing table. This table is currently only used (1) when we need to look-up an Ethernet device based on an IP address, and (2) in the ARP logic when we need to request the MAC address of the router, vs the MAC address of the peer. - Make net_close() nonblocking and free unestablished connections if no free connections available. From Max Holtzberg. - Changed the meaning of the uip_*input functions. They now return success when a packet is dropped; This is needed for the ENCX24J600 driver that must make a decision to return the packet or not: It should not retry dropped packets. From Max Holtzberg. - David Sidrane has completed integration of the CC3000 networking. This is much more than a network driver: It is a complete replacement for the NuttX networking with off-chip networking support in the CC3000. - Numerous enhancements to the ENCX24J600 driver from Max Holtberg. * Other Common Drivers: - The SST25 serial FLASH MTD driver now includes support for the SST25VF016B. From David Sidrane. - Add a preflight method to the SDIO interface to support the STM32 DMA usage model. From Mike Smith. - Enhanced the MMC/SD SDIO driver to perform DMA preflight operations and fail DMA read/write requests that fail preflighting. From Mike Smith. - Add an ioctl command that can be used to trigger ADC/DAC conversion under application control. * File Systems: - Enhanced the FAT32 filesystem code to understand DMA preflight failures, and to use the file sector buffer as a bounce buffer when a user-supplied buffer is not suitable for DMA. From Mike Smith. * Atmel AT91 SAMA5D3x - Add support so that subsets of the total DRAM (and other external memory) can be added to the heap, leaving other memory reserved for other purposes (like the LCDC framebuffers). * Atmel AT91 SAMA5D3x Drivers: - Use more descriptive task names when starting the EHCI and OHCI monitor tasks. - Added a 10/100Base-T Ethernet (EMAC) driver. - Added a 1000Base-T Ethernet (GMAC) driver. - Added a Real Time Clock (RTC) driver and integrated with the NuttX system time logic. - Added support for /dev/random using the SAMA5D3x True Random Number Generator (TRNG). - Added a Watchdog Timer (WDT) driver. - Added a Timer/Counter (TC) library with interface that make be used by other drivers that need timer support. - Added an ADC driver that can collect multiple samples using the sequencer, can be trigger by a timer/counter, and supports DMA data transfers. - Added a touchscreen driver based on the special features of the SAMA5D3 ADC peripheral. - Added an LCD controller (LCDC) frame buffer driver. - Added a CAN driver. However, testing has been delayed because of cabling issues. - Basic header file support is available for the Image Sensor Interface (ISI) camera interface. Work on the camera driver is underway and is expected in the next release. * Atmel AT91 SAMA5D3x-EK Development Boards - Add OS test support for the FPU test. - Enable the task name feature board configuration sto provide prettier ps command output. - Added NX and NxWM configurations to verify the LCD and touchscreen. There are still some outstanding issues with the NxWM configuration as of this release. - The TRNG and /dev/random are now enabled by default in the demo configuration. * Atmel AT91 SAM3/4 Boards: - Add configuration to select revision 3 of the Arduino Due which has some small but important differences. Suggested by gdi@embedders.org. * STMicro STM32: - Add support for the STM32F207ZE chip. From Martin Lederhilger. * STMicro STM32 Boards: - Add configuration for the Spark Core. The initial check-in is basically the Maple Mini board and subsequent development by David Sidrane is his special Spark emulation hardware. The configuration should be very mature when actual Spark hardware is available. - Support for the Olimex STM32 P207 board added by Martin Lederhilger. - Configuration for the Mikroe STM32F4 board configuration updated for audio support by Ken Pettit. * NXP LPC17xx Boards: - zkit-arm-1769: LED1 is now user controllable after booting. From Rashid Fatah. * Kinetis KL Drivers: - PIT and TPM register definitions header files for the from Alan Carvalho de Assis. - Added low-level getc() function for operation with no file system. The KL25Z can now support NSH in a very minimal system that does not even have a file system. * Kinetis KL Boards - A new configuration called minnsh was added is an experiment to see how small we can get the NuttX footprint and still support NSH. From Alan Carvalho de Assis.. * TI Calypso Phones: - Basic board support for the Motorola C139 (Compal E86) phone. From Craig Comstock. * Applications: - Moved several useful examples from apps/examples to apps/system. This includes USB MSC, USB CDC/ACM, and USB Composite. - New addroute and delroute commands added to NSH in order to manage the network routing table. - Numerous enhancements and updates to the CC3000 example from David Sidrane. - Add a new stack monitor daemon that can be used to constantly monitor stack usage by all threads. - Numerous changes to get NSH working with no file system. Basically this suppresses I/O redirection and replaces file I/O with calls to low-level console read/write functions. Suggested by Alan Carvalho de Assis. - apps/system/nxplayer: A new, command-line media player called 'nxplayer' from Ken Pettit. - apps/examples/random: Add a simple test that dumps values from /dev/random. - apps/examples/adc: Add support so that a ADC driven by software triggering can be tested. * Build System: - The MKDEP tools now support a new argument that identifies the object file path. Efforts In Progress. The following are features that are partially implemented but present in this release. They are not likely to be completed soon. * kconfig-fronted Configuration: - Conversion of old configurations to use the kconfig-frontends tool is an ongoing effort that will continue for some time. At this time, only 48% of the configurations have been converted to use the kconfig-frontends tools. Bugfixes (see the ChangeLog for details). Some of these are very important: * Initialization and Scheduling: - IDLE thread initialization logic should not call group_setupidlefiles() if there are no file descriptors (and, hence, no file system). - Fix some cornercase error handling logic: If sched_releasetcb() is called as part of a failed pthread startup before the flags field in the TCB has been initialized, then a crash occurs. Pointed out by David Sidrane. * Networking / Network Drivers: - Look up of a device using subnet will fail if the packet is being sent out of our subnet (via a router). The fallback here is just to use the only device ("eth0") if the subnet lookup fails (this logic was extended to handle multiple Ethernet devices by adding a simple routing table). - Fix some backward conditional logic in send() that enabled the check if the ARP address is in the ARP table. From Max Holtzberg. - Notify the socket layer from the network monitor if a connection is lost before the monitoring callback has been registered. From Max Holtzberg. - send(): Reset the send timeout when the data is ACKed, not when the data is sent. Remove conditions on checking for timeout. From Max Holtzberg. - Correct how the TCP/IP initial minimum MSS is calculated. Max Holtzberg. - TCP state machine: Move tcp connection into SYN_RCVD state after aception instead of bypassing and moving directly into ESTABLISHED. From Max Holtzberg. - Numerous fixes to the ENCX24J600 driver from Max Holtberg. * USB Drivers: - Change naming of SELFPOWERED and REMOTEWAKEUP to avoid name collisions. Prepend the name of the driver (for example CDCACM_SELFPOWERED). - CDC/ACM class driver: Change the interval for the interrupt endpoint from 0xff (invalid) to 10. This is not a critical change but will avoid a complaint from the Linux driver when it overrides the 0xff value. * ARM Cortex-A5: - Fix an error in data cache clean and invalidate functions: Fix of addresses to cache line boundaries. * Atmel AT91 SAMA5D3x Drivers: - Correct some inconsistencies in the way that USB configuration settings are used. This caused compilation errors in SAMA5 OHCI when USB debug was ON but USB host tracing was off. - When 480MHz UPLL is used to drive OHCI, it should have a divider of 10. However, that does not work. A divider of 5 does. Why?. - OHCI HCD: Fix a place where DMA-related data needed to be flushed to data cache; Fix another where a virtual address was being used in a register where a physical address was required. - HSMCI Driver: TX DMA disabled. It is just not reliable. No idea why. RX DMA is still used. - STM32F103C pinmapping corrections from David Sidrane. * Atmel SAMA5D3x-EK Board - Increase the number of pre-allocated watchdog timers. The default number of 4 was easily being exhausted in the more complex configurations. * STMicro STM32: - STM32 F4 DMA definitions: Typo fixes for UART7 and UART8 DMA configs. From Mike Smith. - DMA priority configuration corrections from Mike Smith. - Changes to the stm32_dmacapable API. In order to correctly verify that a buffer can be transferred, the transfer count and the CCR value are required. Implemented stm32_dmacapable for stm32f1xx devices. Enhanced stm32_dmacapable for stm32f2xx and stm32f4xx devices to check for additional conditions that will cause DMA to fail or lose data. - STM32 F1 DMA fix from David Sidrane: The DMA_CNDTRx register cannot be modified if the DMA channel is disabled. * STMicro STM32 Drivers: - Fix compilation errors from bad bit definitions in ADC and PWM register. From Martin Lederhilger. - DMA-related fixes to the SPI driver from Ken Pettit. * NXP LPC17xx Drivers: - Remove undefined spi_select() prototype. This was causing compile time warnings. * NXP LPC17xx Boards: - zkit-arm-1768: MMC/SD is on SPI, not SSP0. From Rashid Fatah. * C Library - scanf() fixes from kfrolov: 1) sscanf() function hangs in the following example: sscanf("2", "%u,%u,%u,%u", ...), 2) sscanf() returns incorrect number of parsed numbers if some arguments can't be parsed: sscanf("=2", "%u,%u,%u,%u",...)==1 instead of 0, and 3) using of char* instead of const char* in vsscanf function leads to warnings from GCC. * Build System - Dependency generation generation was broken for directories that keep objects in a sub-directory. The MKDEP tools now support a new argument that identifies the object file path. - tools/define.sh: 'cut' no longer works as it once did. Script adapted to observed behavior. * Applications: - Remove a warning from the NSH library when DHCP is not enabled. - Default NSH IP address should be 0x0a000001 (10.0.0.1), not 0xa0000001 (160.0.0.1). Ditto for the gateway. - Add some missing options to the OS test Kconfig file - Fix some bad conditional compilation in the USB monitor. - Fix default I2C frequency used by the I2C tool: 400KHz instead of 4MHz. Suggested by Max Kriegleder. - Increase stack size for the system/info command. Ken Petit reports that this simple command can exceed its 768 stack size under certain conditions. The size is marginal and has been increased to 1024 by default but is also now configurable. - apps/Makefile: Needs to include external/Make.defs if we want allow external applications to participate in the NuttX configuration. Suggested by gdi@embedders.org. - apps/netutils/telnetd: Missing argument to debug statement can cause crashes in certain error conditions. From David Sidrane. - apps/examples/can: Correct an error in a debug statement. From Martin Lederhilger.