/****************************************************************************
 * boards/arm/stm32l4/b-l475e-iot01a/src/stm32_autoleds.c
 *
 *   Copyright (C) 2017 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ****************************************************************************/

/* LEDs
 *
 * A single LED is available driven by PA13.
 *
 * These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
 * defined.  In that case, the usage by the board port is defined in
 * include/board.h and src/sam_autoleds.c. The LEDs are used to encode
 * OS-related events as follows:
 *
 *   ------------------- ----------------------- ------
 *   SYMBOL              Meaning                 LED
 *   ------------------- ----------------------- ------
 *   LED_STARTED         NuttX has been started  OFF
 *   LED_HEAPALLOCATE    Heap has been allocated OFF
 *   LED_IRQSENABLED     Interrupts enabled      OFF
 *   LED_STACKCREATED    Idle stack created      ON
 *   LED_INIRQ           In an interrupt         N/C
 *   LED_SIGNAL          In a signal handler     N/C
 *   LED_ASSERTION       An assertion failed     N/C
 *   LED_PANIC           The system has crashed  FLASH
 *
 * Thus is LED is statically on, NuttX has successfully  booted and is,
 * apparently, running normally.  If LED is flashing at approximately
 * 2Hz, then a fatal error has been detected and the system has halted.
 */

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>
#include <debug.h>

#include <nuttx/board.h>
#include <arch/board/board.h>

#include "stm32l4_gpio.h"
#include "b-l475e-iot01a.h"

#ifdef CONFIG_ARCH_LEDS

/****************************************************************************
 * Public Functions
 ****************************************************************************/

/****************************************************************************
 * Name: board_autoled_initialize
 ****************************************************************************/

void board_autoled_initialize(void)
{
  /* Configure LED gpio as output */

  stm32l4_configgpio(GPIO_LED2);
}

/****************************************************************************
 * Name: board_autoled_on
 ****************************************************************************/

void board_autoled_on(int led)
{
  if (led == 1 || led == 3)
    {
      stm32l4_gpiowrite(GPIO_LED2, true);
    }
}

/****************************************************************************
 * Name: board_autoled_off
 ****************************************************************************/

void board_autoled_off(int led)
{
  if (led == 3)
    {
      stm32l4_gpiowrite(GPIO_LED2, false);
    }
}

#endif /* CONFIG_ARCH_LEDS */