/****************************************************************************
 * boards/xtensa/esp32/esp32-wrover-kit/include/board.h
 *
 * Licensed to the Apache Software Foundation (ASF) under one or more
 * contributor license agreements.  See the NOTICE file distributed with
 * this work for additional information regarding copyright ownership.  The
 * ASF licenses this file to you under the Apache License, Version 2.0 (the
 * "License"); you may not use this file except in compliance with the
 * License.  You may obtain a copy of the License at
 *
 *   http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
 * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
 * License for the specific language governing permissions and limitations
 * under the License.
 *
 ****************************************************************************/

#ifndef __BOARDS_XTENSA_ESP32_ESP32_WROVER_KIT_INCLUDE_BOARD_H
#define __BOARDS_XTENSA_ESP32_ESP32_WROVER_KIT_INCLUDE_BOARD_H

/****************************************************************************
 * Pre-processor Definitions
 ****************************************************************************/

/* Clocking *****************************************************************/

/* The ESP32 Wrover kit board uses a 40MHz crystal oscillator. */

#define BOARD_XTAL_FREQUENCY  40000000

#ifdef CONFIG_ESP32_DEFAULT_CPU_FREQ_MHZ
#  define BOARD_CLOCK_FREQUENCY (CONFIG_ESP32_DEFAULT_CPU_FREQ_MHZ * 1000000)
#else
#  define BOARD_CLOCK_FREQUENCY 80000000
#endif

/* GPIO definitions *********************************************************/

/* Display */

#define DISPLAY_SPI       2
#define DISPLAY_DC        21
#define DISPLAY_RST       18
#define DISPLAY_BCKL      5

/* LED definitions **********************************************************/

/* Define how many LEDs this board has (needed by userleds) */

#define BOARD_LED1        0
#define BOARD_LED2        1
#define BOARD_LED3        2

#define BOARD_LED_RED     BOARD_LED1    /* GPIO 0 */
#define BOARD_LED_GREEN   BOARD_LED2    /* GPIO 2 */
#define BOARD_LED_BLUE    BOARD_LED3    /* GPIO 4 */

/* LED bits for use with autoleds */

#define BOARD_LED1_BIT    (1 << BOARD_LED1)
#define BOARD_LED2_BIT    (1 << BOARD_LED2)
#define BOARD_LED3_BIT    (1 << BOARD_LED3)

/* GPIO 2 is used by MMCSD driver as MISO, therefore, it can't be used as
 * USER LED
 */
#ifdef CONFIG_MMCSD

/* GPIO 0 is used by BUTTONS, it can't be used as USER LED */
#ifdef CONFIG_INPUT_BUTTONS
#  define BOARD_NLEDS       1
#else
#  define BOARD_NLEDS       2
#endif

#else  /* MMCSD */

/* GPIO 0 is used by BUTTONS, it can't be used as USER LED */
#ifdef CONFIG_INPUT_BUTTONS
#  define BOARD_NLEDS       2
#else
#  define BOARD_NLEDS       3
#endif

#endif

/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 3 LEDs on
 * board the ESP-WROVER-KIT.  The following definitions describe how
 * NuttX controls the LEDs:
 */

/* These values index an array that contains the bit definitions for the
 * correct LEDs (see esp32_autoleds.c).
 */

#define LED_STARTED       0  /* LED2 */
#define LED_HEAPALLOCATE  1  /* LED3 */
#define LED_IRQSENABLED   2  /* LED3 + LED2 */
#define LED_STACKCREATED  3  /* LED3 */
#define LED_INIRQ         4  /* LED1 + LED3 */
#define LED_SIGNAL        5  /* LED2 + LED3 */
#define LED_ASSERTION     6  /* LED1 + LED2 + LED3 */
#define LED_PANIC         7  /* LED1  + N/C  + N/C */

/* The values below are used only to distinguish between the CPUs.
 * The LEDs are actually mapped as:
 *    CPU0 -> GPIO_LED1 (Red LED)
 *    CPU1 -> GPIO_LED2 (Green LED)
 * Note that from the previous list only LED_HEAPALLOCATE will still be
 * valid.  This is to avoid collisions and to keep a way to show a successful
 * heap allocation.  The LED used is still LED3 (Blue LED).
 */

#ifdef CONFIG_ARCH_LEDS_CPU_ACTIVITY
#  define LED_CPU0        8
#  define LED_CPU1        9
#  define LED_CPU         (LED_CPU0 + up_cpu_index())
#endif

/* GPIO pins used by the GPIO Subsystem */

#define BOARD_NGPIOIN     1 /* Amount of GPIO Input pins */
#define BOARD_NGPIOOUT    1 /* Amount of GPIO Output pins */
#define BOARD_NGPIOINT    1 /* Amount of GPIO Input w/ Interruption pins */

#endif /* __BOARDS_XTENSA_ESP32_ESP32_WROVER_KIT_INCLUDE_BOARD_H */