/**************************************************************************** * drivers/sensors/t67xx.c * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ #if !defined(CONFIG_I2C) # error i2c support required #endif /* This driver is tested with Telaire T6713. Likely works for Telaire T6703 * and other models as well, but this has not been verified. No test * animals were gassed during testing. */ /* Modbus registers */ #define T67XX_REG_FWREV 0x1389 /* Firmware revision */ #define T67XX_REG_STATUS 0x138a /* Status */ #define T67XX_REG_GASPPM 0x138b /* Gas parts per million */ #define T67XX_REG_RESET 0x03e8 /* Reset device */ #define T67XX_REG_SPCAL 0x03ec /* Single point calibration */ #define T67XX_REG_SLAVEADDR 0x0fa5 /* Slave address */ #define T67XX_REG_ABCLOGIC 0x03ee /* ABC Logic enable/disable */ /* Status register bits */ #define T67XX_STATUS_ERROR (1 << 0) /* Error condition */ #define T67XX_STATUS_FLASH_ERROR (1 << 1) /* Flash error */ #define T67XX_STATUS_CALIB_ERROR (1 << 2) /* Calibration error */ /* [3:7] reserved */ #define T67XX_STATUS_RS232 (1 << 8) /* RS-232 error */ #define T67XX_STATUS_RS485 (1 << 9) /* RS-485 error */ #define T67XX_STATUS_I2C (1 << 10) /* I2C error */ #define T67XX_STATUS_WARMUP (1 << 11) /* Warm-up mode */ /* [12:14] reserved */ #define T67XX_STATUS_SPCAL (1 << 15) /* Single point calibration */ /* Command bits */ #define RESET_SENSOR 0xff00 /* Reset sensor */ #define SPCAL_START 0xff00 /* Start SP calibration */ #define SPCAL_STOP 0x0000 /* Stop SP calibration */ #define ABCLOGIC_ENABLE 0xff00 /* Enable ABC Logic */ #define ABCLOGIC_DISABLE 0x0000 /* Disable ABC Logic */ /* Required times before sensor reaches either minimal or full * operational accuracy. */ #define T67XX_UPTIME_MINIMAL_SEC 120 /* two minutes */ #define T67XX_UPTIME_FULL_SEC (10 * 60) /* ten minutes */ #define T67XX_UPTIME_ABCLOGIC_SEC (24 * 60 * 60) /* a day */ /* I2C constants */ #define T67XX_I2C_FREQUENCY 100000 /* Only supported I2C speed */ #define T67XX_I2C_DELAY_MSEC 10 /* 5-10 ms recommended, 10 ms * is always safe. */ /**************************************************************************** * Private Types ****************************************************************************/ struct t67xx_dev_s { FAR struct i2c_master_s *i2c; /* I2C interface */ uint8_t addr; /* I2C address */ struct timespec boot_time; /* When sensor was booted */ mutex_t devlock; }; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ /* I2C Helpers */ static int t67xx_read16(FAR struct t67xx_dev_s *priv, uint16_t regaddr, FAR uint16_t *regvalue); static int t67xx_write16(FAR struct t67xx_dev_s *priv, uint16_t regaddr, FAR uint16_t regvalue, bool read_reply); /* Driver features */ static int t67xx_check_status(FAR struct t67xx_dev_s *priv, bool *warming_up, bool *calibrating); static int t67xx_read_fwrev(FAR struct t67xx_dev_s *priv, uint16_t *rev); static int t67xx_read_gas_ppm(FAR struct t67xx_dev_s *priv, FAR struct t67xx_value_s *buffer); static int t67xx_spcal(FAR struct t67xx_dev_s *priv, bool start); static int t67xx_abclogic(FAR struct t67xx_dev_s *priv, bool enable); static int t67xx_reset(FAR struct t67xx_dev_s *priv); /* Character driver methods */ static ssize_t t67xx_read(FAR struct file *filep, FAR char *buffer, size_t buflen); static ssize_t t67xx_write(FAR struct file *filep, FAR const char *buffer, size_t buflen); static int t67xx_ioctl(FAR struct file *filep, int cmd, unsigned long arg); /**************************************************************************** * Private Data ****************************************************************************/ static const struct file_operations g_t67xxfops = { NULL, /* open */ NULL, /* close */ t67xx_read, /* read */ t67xx_write, /* write */ NULL, /* seek */ t67xx_ioctl, /* ioctl */ }; /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: t67xx_read16 * * Description: * Read 16-bit register * ****************************************************************************/ static int t67xx_read16(FAR struct t67xx_dev_s *priv, uint16_t regaddr, FAR uint16_t *regvalue) { struct i2c_config_s config; uint8_t buf[5]; uint8_t rxbuf[4] = { 0 }; int ret; DEBUGASSERT(priv != NULL); DEBUGASSERT(regvalue != NULL); /* Set up the I2C configuration. */ config.frequency = T67XX_I2C_FREQUENCY; config.address = priv->addr; config.addrlen = 7; /* Set up the Modbus read request. */ buf[0] = 4; buf[1] = (regaddr >> 8) & 0xff; buf[2] = regaddr & 0xff; buf[3] = 0; buf[4] = 1; /* Write the Modbus read request. */ ret = i2c_write(priv->i2c, &config, buf, sizeof(buf)); if (ret < 0) { snerr("ERROR: i2c_write failed: %d\n", ret); return ret; } /* Wait and read response. */ up_mdelay(T67XX_I2C_DELAY_MSEC); ret = i2c_read(priv->i2c, &config, rxbuf, sizeof(rxbuf)); if (ret < 0) { snerr("ERROR: i2c_read failed: %d\n", ret); return ret; } if (rxbuf[0] != 4 || rxbuf[1] != 2) { #ifdef CONFIG_DEBUG_SENSORS_ERROR lib_dumpbuffer("ERROR: sensor wrong data", rxbuf, sizeof(rxbuf)); #endif return -EIO; } *regvalue = ((uint16_t)rxbuf[2] << 8) | rxbuf[3]; return ret; } /**************************************************************************** * Name: t67xx_write16 * * Description: * Write 16-bit register. If 'reply' is true, sensor response is read * for verification. * ****************************************************************************/ static int t67xx_write16(FAR struct t67xx_dev_s *priv, uint16_t regaddr, FAR uint16_t regvalue, bool reply) { struct i2c_config_s config; uint8_t buf[5]; uint8_t rxbuf[5] = { 0 }; int ret; DEBUGASSERT(priv != NULL); /* Set up the I2C configuration. */ config.frequency = T67XX_I2C_FREQUENCY; config.address = priv->addr; config.addrlen = 7; /* Set up the Modbus write request. */ buf[0] = 5; buf[1] = (regaddr >> 8) & 0xff; buf[2] = regaddr & 0xff; buf[3] = (regvalue >> 8) & 0xff; buf[4] = regvalue & 0xff; /* Write the Modbus write request. */ ret = i2c_write(priv->i2c, &config, buf, sizeof(buf)); if (ret < 0) { snerr("ERROR: i2c_write failed: %d\n", ret); return ret; } /* There is no reply for Reset command, exit early. */ if (!reply) { return ret; } /* Wait and read response. */ up_mdelay(T67XX_I2C_DELAY_MSEC); ret = i2c_read(priv->i2c, &config, rxbuf, sizeof(rxbuf)); if (ret < 0) { snerr("ERROR: i2c_read failed: %d\n", ret); return ret; } if (memcmp(rxbuf, buf, sizeof(rxbuf)) != 0) { #ifdef CONFIG_DEBUG_SENSORS_ERROR lib_dumpbuffer("ERROR: sensor wrong data", rxbuf, sizeof(rxbuf)); #endif return -EIO; } return ret; } /**************************************************************************** * Name: t67xx_check_status * * Description: * Check status register. * ****************************************************************************/ static int t67xx_check_status(FAR struct t67xx_dev_s *priv, bool *warming_up, bool *calibrating) { uint16_t status; int ret; /* Read the status register. */ ret = t67xx_read16(priv, T67XX_REG_STATUS, &status); if (ret < 0) { snerr("ERROR: sensor cannot read status: %d\n", ret); return ret; } sninfo("status 0x%04x\n", status); /* We ignore I2C error here, as it is checked for every bus * operation anyway. */ if (status & (T67XX_STATUS_ERROR | T67XX_STATUS_FLASH_ERROR | T67XX_STATUS_CALIB_ERROR)) { snerr("ERROR: sensor error 0x%04x\n", status); return ERROR; } *warming_up = status & T67XX_STATUS_WARMUP; *calibrating = status & T67XX_STATUS_SPCAL; return OK; } /**************************************************************************** * Name: t67xx_read_fwrev * * Description: * Check firmware revision register. * ****************************************************************************/ static int t67xx_read_fwrev(FAR struct t67xx_dev_s *priv, uint16_t *rev) { uint16_t fwrev; int ret; /* Read the FW revision register. */ ret = t67xx_read16(priv, T67XX_REG_FWREV, &fwrev); if (ret < 0) { snerr("ERROR: sensor cannot read reg: %d\n", ret); return ret; } sninfo("sensor FW rev: 0x%04x\n", fwrev); if (rev) { *rev = fwrev; } return OK; } /**************************************************************************** * Name: has_time_passed * * Description: * Return true if curr >= start + secs_since_start * ****************************************************************************/ static bool has_time_passed(struct timespec curr, struct timespec start, unsigned int secs_since_start) { if ((long)((start.tv_sec + secs_since_start) - curr.tv_sec) == 0) { return start.tv_nsec <= curr.tv_nsec; } return (long)((start.tv_sec + secs_since_start) - curr.tv_sec) <= 0; } /**************************************************************************** * Name: t67xx_read_gas_ppm * * Description: * Read the current carbon dioxide level. * ****************************************************************************/ static int t67xx_read_gas_ppm(FAR struct t67xx_dev_s *priv, FAR struct t67xx_value_s *buffer) { uint16_t ppm; bool warming_up; bool calibrating; struct timespec ts; int ret; clock_systime_timespec(&ts); if (!has_time_passed(ts, priv->boot_time, T67XX_UPTIME_MINIMAL_SEC)) { snwarn("WARN: sensor not ready yet\n"); return -EAGAIN; } /* Check sensor status. */ ret = t67xx_check_status(priv, &warming_up, &calibrating); if (ret != OK) { return ret; } /* Sanity check warm-up behavior. */ if (!has_time_passed(ts, priv->boot_time, T67XX_UPTIME_FULL_SEC)) { if (!warming_up) { snwarn("WARN: sensor not fully warm-up\n"); warming_up = true; } } else if (warming_up) { snwarn("WARN: sensor still warming up after %d secs\n", T67XX_UPTIME_FULL_SEC); } /* Read the CO2 level. */ ret = t67xx_read16(priv, T67XX_REG_GASPPM, &ppm); if (ret < 0) { return ret; } add_sensor_randomness(ts.tv_nsec ^ (int)ppm); buffer->gas_ppm = ppm; buffer->warming_up = warming_up; buffer->calibrating = calibrating; sninfo("ppm %d, warming up %d, calibrating %d\n", (int)ppm, warming_up, calibrating); return OK; } /**************************************************************************** * Name: t67xx_spcal * * Description: * Start or stop sensor single-point calibration. * ****************************************************************************/ static int t67xx_spcal(FAR struct t67xx_dev_s *priv, bool start) { int ret; ret = t67xx_write16(priv, T67XX_REG_SPCAL, start ? SPCAL_START : SPCAL_STOP, true); if (ret < 0) { snerr("ERROR: sp calibration failed: %d\n", ret); return ret; } return ret; } /**************************************************************************** * Name: t67xx_abclogic * * Description: * Start or stop sensor ABC Logic feature. * * Automatic Background Logic, is a self-calibration technique that is * designed to be used in applications where concentrations will drop to * outside ambient conditions (400 ppm) at least three times in a 7 days. * * With ABC Logic enabled, the sensor will typically reach its operational * accuracy after 24 hours of continuous operation at a condition that it * was exposed to ambient reference levels of air at 400 ppm CO2. Sensor * will maintain accuracy specifications with ABC Logic enabled, given * that it is at least four times in 21 days exposed to the reference * value and this reference value is the lowest concentration to which * the sensor is exposed. ABC Logic requires continuous operation of the * sensor for periods of at least 24 hours. * * Currently driver does not try to check for these constraints. * ****************************************************************************/ static int t67xx_abclogic(FAR struct t67xx_dev_s *priv, bool enable) { int ret; ret = t67xx_write16(priv, T67XX_REG_ABCLOGIC, enable ? ABCLOGIC_ENABLE : ABCLOGIC_DISABLE, true); if (ret < 0) { snerr("ERROR: ABC Logic failed: %d\n", ret); return ret; } return ret; } /**************************************************************************** * Name: t67xx_reset * * Description: * Reset sensor. Data-sheet does not recommend using this. * ****************************************************************************/ static int t67xx_reset(FAR struct t67xx_dev_s *priv) { int ret; ret = t67xx_write16(priv, T67XX_REG_RESET, RESET_SENSOR, false); if (ret < 0) { snerr("ERROR: reset failed: %d\n", ret); return ret; } /* Sensor uptime starting again from zero. */ clock_systime_timespec(&priv->boot_time); return ret; } /**************************************************************************** * Name: t67xx_read ****************************************************************************/ static ssize_t t67xx_read(FAR struct file *filep, FAR char *buffer, size_t buflen) { FAR struct inode *inode = filep->f_inode; FAR struct t67xx_dev_s *priv = inode->i_private; FAR struct t67xx_value_s *ptr; ssize_t nsamples; int i; int ret; /* Get exclusive access */ ret = nxmutex_lock(&priv->devlock); if (ret < 0) { return ret; } /* How many samples were requested to get? */ nsamples = buflen / sizeof(struct t67xx_value_s); ptr = (FAR struct t67xx_value_s *)buffer; sninfo("buflen: %d nsamples: %d\n", buflen, nsamples); /* Get the requested number of samples */ for (i = 0; i < nsamples; i++) { struct t67xx_value_s gas_ppm; /* Read the next struct t67xx_value_s */ ret = t67xx_read_gas_ppm(priv, &gas_ppm); if (ret < 0) { snerr("ERROR: t67xx_read_gas_ppm failed: %d\n", ret); nxmutex_unlock(&priv->devlock); return (ssize_t)ret; } /* Save the value in the user buffer */ *ptr++ = gas_ppm; } nxmutex_unlock(&priv->devlock); return nsamples * sizeof(struct t67xx_value_s); } /**************************************************************************** * Name: t67xx_write ****************************************************************************/ static ssize_t t67xx_write(FAR struct file *filep, FAR const char *buffer, size_t buflen) { return -ENOSYS; } /**************************************************************************** * Name: t67xx_ioctl ****************************************************************************/ static int t67xx_ioctl(FAR struct file *filep, int cmd, unsigned long arg) { FAR struct inode *inode = filep->f_inode; FAR struct t67xx_dev_s *priv = inode->i_private; int ret; /* Get exclusive access */ ret = nxmutex_lock(&priv->devlock); if (ret < 0) { return ret; } switch (cmd) { /* Soft reset the sensor, Arg: None */ case SNIOC_RESET: ret = t67xx_reset(priv); sninfo("reset ret: %d\n", ret); break; /* Dump registers, currently just FWREV reg, Arg: None */ case SNIOC_DUMP_REGS: ret = t67xx_read_fwrev(priv, NULL); break; /* Calibrate the sensor, Arg: uint8_t value */ case SNIOC_SPCALIB: ret = t67xx_spcal(priv, !!arg); sninfo("spcal ret: %d\n", ret); break; /* Enable/disable the ABC Logic feature, Arg: uint8_t value */ case SNIOC_ABCLOGIC: ret = t67xx_abclogic(priv, !!arg); sninfo("abclogic ret: %d\n", ret); break; default: sninfo("Unrecognized cmd: %d\n", cmd); ret = -ENOTTY; break; } nxmutex_unlock(&priv->devlock); return ret; } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: t67xx_register * * Description: * Register the T67XX character device as 'devpath' * * Input Parameters: * devpath - The full path to the driver to register. E.g., "/dev/co2_0" * i2c - An instance of the I2C interface to use to communicate with T67XX * addr - The I2C address of the T67XX. For T6713 this is initially 0x15 * but it can be changed by the SLAVE ADDRESS command. * * Returned Value: * Zero (OK) on success; a negated errno value on failure. * ****************************************************************************/ int t67xx_register(FAR const char *devpath, FAR struct i2c_master_s *i2c, uint8_t addr) { FAR struct t67xx_dev_s *priv; int ret; DEBUGASSERT(i2c != NULL); DEBUGASSERT(addr == T67XX_I2C_ADDR); /* Initialize the t67xx device structure. */ priv = (FAR struct t67xx_dev_s *)kmm_malloc(sizeof(struct t67xx_dev_s)); if (priv == NULL) { snerr("ERROR: Failed to allocate instance\n"); return -ENOMEM; } priv->i2c = i2c; priv->addr = addr; nxmutex_init(&priv->devlock); clock_systime_timespec(&priv->boot_time); /* Register the character driver. */ ret = register_driver(devpath, &g_t67xxfops, 0666, priv); if (ret < 0) { snerr("ERROR: Failed to register driver: %d\n", ret); goto errout; } sninfo("(addr=0x%02x) registered at %s\n", priv->addr, devpath); return ret; errout: nxmutex_destroy(&priv->devlock); kmm_free(priv); return ret; }