/**************************************************************************** * drivers/sensors/ws2812.c * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #ifdef CONFIG_WS2812 /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* In order to meet the signaling timing requirements, the waveforms required * to represent a 0/1 symbol are created by specific SPI bytes defined here. * * Only two target frequencies: 4 MHz and 8 MHz. However, given the tolerance * allowed in the WS2812 timing specs, two ranges around those target * frequencies can be used for better flexibility. Extreme frequencies rounded * to the nearest multiple of 100 kHz which meets the specs. Try to avoid * using the extreme frequencies. * * If using an LED different to the WS2812 (e.g. WS2812B) check its timing * specs, which may vary slightly, to decide which frequency is safe to use. * * WS2812 specs: * T0H range: 200ns - 500ns * T1H range: 550ns - 850ns * Reset: low signal >50us */ #if CONFIG_WS2812_FREQUENCY >= 3600000 && CONFIG_WS2812_FREQUENCY <= 5000000 # define WS2812_ZERO_BYTE 0b01000000 /* 200ns at 5 MHz, 278ns at 3.6 MHz */ # define WS2812_ONE_BYTE 0b01110000 /* 600ns at 5 MHz, 833ns at 3.6 MHz */ #elif CONFIG_WS2812_FREQUENCY >= 5900000 && CONFIG_WS2812_FREQUENCY <= 9000000 # define WS2812_ZERO_BYTE 0b01100000 /* 222ns at 9 MHz, 339ns at 5.9 MHz */ # define WS2812_ONE_BYTE 0b01111100 /* 556ns at 9 MHz, 847ns at 5.9 MHz */ #else # error "Unsupported SPI Frequency" #endif /* Reset bytes * Number of empty bytes to create the reset low pulse * Aiming for 60 us, safely above the 50us required. */ #define WS2812_RST_CYCLES (CONFIG_WS2812_FREQUENCY * 60 / 1000000 / 8) #define WS2812_BYTES_PER_LED (8 * 3) #define WS2812_RW_PIXEL_SIZE 4 /* Transmit buffer looks like: * [<----reset bytes---->|<-RGBn->...<-RGB0->|<----reset bytes---->] * * It is important that this is shipped as close to one chunk as possible * in order to meet timing requirements and to keep MOSI from going high * between transactions. Some chips will leave MOSI at the state of the * MSB of the last byte for this reason it is recommended to shift the * bits that represents the zero or one waveform so that the MSB is 0. * The reset clocks will pad the shortened low at the end. */ #define TXBUFF_SIZE(n) (WS2812_RST_CYCLES * 2 + n * WS2812_BYTES_PER_LED) /**************************************************************************** * Private Types ****************************************************************************/ struct ws2812_dev_s { FAR struct spi_dev_s *spi; /* SPI interface */ uint16_t nleds; /* Number of addressable LEDs */ uint8_t *tx_buf; /* Buffer for write transaction and state */ sem_t exclsem; /* Assures exclusive access to the driver */ }; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ static inline void ws2812_configspi(FAR struct spi_dev_s *spi); static void ws2812_pack(FAR uint8_t *buf, uint32_t rgb); /* Character driver methods */ static int ws2812_open(FAR struct file *filep); static int ws2812_close(FAR struct file *filep); static ssize_t ws2812_read(FAR struct file *filep, FAR char *buffer, size_t buflen); static ssize_t ws2812_write(FAR struct file *filep, FAR const char *buffer, size_t buflen); static off_t ws2812_seek(FAR struct file *filep, off_t offset, int whence); /**************************************************************************** * Private Data ****************************************************************************/ static const struct file_operations g_ws2812fops = { ws2812_open, /* open */ ws2812_close, /* close */ ws2812_read, /* read */ ws2812_write, /* write */ ws2812_seek, /* seek */ NULL, /* ioctl */ NULL, /* poll */ #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS NULL /* unlink */ #endif }; /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: ws2812_configspi * * Description: * Set the SPI bus configuration * ****************************************************************************/ static inline void ws2812_configspi(FAR struct spi_dev_s *spi) { /* Configure SPI for the WS2812 * There is no CS on this device we just use MOSI and it is exclusive */ SPI_LOCK(spi, true); /* Exclusive use of the bus */ SPI_SETMODE(spi, SPIDEV_MODE3); SPI_SETBITS(spi, 8); SPI_HWFEATURES(spi, 0); SPI_SETFREQUENCY(spi, CONFIG_WS2812_FREQUENCY); } /**************************************************************************** * Name: ws2812_pack * * Description: * This writes the expanded SPI transaction to the transaction buffer * for a given 24bit RGB value. * * Input Parameters: * buf - The location in the transmit buffer to write. * rgb - A 24bit RGB color 8bit red, 8-bit green, 8-bit blue * ****************************************************************************/ static void ws2812_pack(FAR uint8_t *buf, uint32_t rgb) { uint8_t bit_idx; uint8_t byte_idx; uint8_t offset = 0; uint8_t color; uint32_t grb; grb = (rgb & 0x00ff00) << 8; grb |= (rgb & 0xff0000) >> 8; grb |= rgb & 0x0000ff; for (byte_idx = 0; byte_idx < 3; byte_idx++) { color = (uint8_t)(grb >> (8 * (2 - byte_idx))); for (bit_idx = 0; bit_idx < 8; bit_idx++) { if (color & (1 << (7 - bit_idx))) { buf[offset] = WS2812_ONE_BYTE; } else { buf[offset] = WS2812_ZERO_BYTE; } offset++; } } } /**************************************************************************** * Name: ws2812_open * * Description: * This function is called whenever the WS2812 device is opened. * ****************************************************************************/ static int ws2812_open(FAR struct file *filep) { return OK; } /**************************************************************************** * Name: ws2812_close * * Description: * This routine is called when the WS2812 device is closed. * ****************************************************************************/ static int ws2812_close(FAR struct file *filep) { return OK; } /**************************************************************************** * Name: ws2812_read ****************************************************************************/ static ssize_t ws2812_read(FAR struct file *filep, FAR char *buffer, size_t buflen) { return -ENOSYS; } /**************************************************************************** * Name: ws2812_write * * Description: * This routine is called when writing to the WS2812 device. Data buffer * should be an array of 32bit values holding 24bits of color information * in host byte ordering 0x**rrggbb. * ****************************************************************************/ static ssize_t ws2812_write(FAR struct file *filep, FAR const char *buffer, size_t buflen) { FAR struct inode *inode = filep->f_inode; FAR struct ws2812_dev_s *priv = inode->i_private; FAR uint8_t *tx_pixel; FAR uint32_t *pixel_buf = (FAR uint32_t *)buffer; size_t cur_led; size_t start_led; size_t end_led; size_t written = 0; if (buffer == NULL) { lederr("ERROR: Buffer is null\n"); set_errno(EINVAL); return -1; } /* We need at least one LED, so 1 byte */ if (buflen < 1) { lederr("ERROR: You need to control at least 1 LED!\n"); set_errno(EINVAL); return -1; } if ((buflen % WS2812_RW_PIXEL_SIZE) != 0) { lederr("ERROR: LED values must be 24bit packed in 32bit\n"); set_errno(EINVAL); return -1; } nxsem_wait(&priv->exclsem); start_led = filep->f_pos / WS2812_RW_PIXEL_SIZE; tx_pixel = priv->tx_buf + WS2812_RST_CYCLES + \ start_led * WS2812_BYTES_PER_LED; end_led = start_led + (buflen / WS2812_RW_PIXEL_SIZE) - 1; ledinfo("Start: %d End: %d\n", start_led, end_led); if (end_led > (priv->nleds -1)) { end_led = priv->nleds - 1; } for (cur_led = start_led; cur_led <= end_led; cur_led++) { ws2812_pack(tx_pixel, *pixel_buf & 0xffffff); pixel_buf++; tx_pixel += WS2812_BYTES_PER_LED; written += WS2812_RW_PIXEL_SIZE; } SPI_SNDBLOCK(priv->spi, priv->tx_buf, TXBUFF_SIZE(priv->nleds)); /* Update LED position and handle case were we wrote the last LED */ filep->f_pos += written; if (end_led == (priv->nleds - 1)) { filep->f_pos -= WS2812_RW_PIXEL_SIZE; } nxsem_post(&priv->exclsem); return written; } /**************************************************************************** * Name: ws2812_seek * * Description: * This routine is called when seeking the WS2812 device. This can be used * to address the starting LED to write. This should be done on a full * color boundary which is 32bits. e.g. LED0 - offset 0, LED 8 - offset 32 * ****************************************************************************/ static off_t ws2812_seek(FAR struct file *filep, off_t offset, int whence) { FAR struct inode *inode = filep->f_inode; FAR struct ws2812_dev_s *priv = inode->i_private; off_t maxpos; off_t pos; if ((offset % WS2812_RW_PIXEL_SIZE) != 0) { return (off_t)-EINVAL; } nxsem_wait(&priv->exclsem); maxpos = (priv->nleds - 1) * WS2812_RW_PIXEL_SIZE; pos = filep->f_pos; switch (whence) { case SEEK_CUR: pos += offset; if (pos > maxpos) { pos = maxpos; } else if (pos < 0) { pos = 0; } filep->f_pos = pos; break; case SEEK_SET: pos = offset; if (pos > maxpos) { pos = maxpos; } else if (pos < 0) { pos = 0; } filep->f_pos = pos; break; case SEEK_END: pos = maxpos + offset; if (pos > maxpos) { pos = maxpos; } else if (pos < 0) { pos = 0; } filep->f_pos = pos; break; default: /* Return EINVAL if the whence argument is invalid */ pos = (off_t)-EINVAL; break; } nxsem_post(&priv->exclsem); return pos; } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: ws2812_leds_register * * Description: * Register the WS2812 character device as 'devpath' * * Input Parameters: * devpath - The full path to the driver to register. E.g., "/dev/leds0" * spi - An instance of the SPI interface to use to communicate with * WS2812 * nleds - Number of addressable LEDs * * Returned Value: * Zero (OK) on success; a negated errno value on failure. * ****************************************************************************/ int ws2812_leds_register(FAR const char *devpath, FAR struct spi_dev_s *spi, uint16_t nleds) { FAR struct ws2812_dev_s *priv; int ret; int led; /* Initialize the WS2812 device structure */ priv = (FAR struct ws2812_dev_s *)kmm_malloc(sizeof(struct ws2812_dev_s)); if (!priv) { lederr("ERROR: Failed to allocate instance\n"); return -ENOMEM; } priv->nleds = nleds; priv->tx_buf = (FAR uint8_t *)kmm_zalloc(TXBUFF_SIZE(priv->nleds)); if (!priv->tx_buf) { lederr("ERROR: Failed to allocate tx buffer\n"); kmm_free(priv); return -ENOMEM; } /* Mark LED section of TX buffer as off */ for (led = 0; led < priv->nleds; led++) { ws2812_pack( priv->tx_buf + WS2812_RST_CYCLES + led * WS2812_BYTES_PER_LED, 0); } priv->spi = spi; ws2812_configspi(priv->spi); nxsem_init(&priv->exclsem, 0, 1); SPI_SNDBLOCK(priv->spi, priv->tx_buf, TXBUFF_SIZE(priv->nleds)); /* Register the character driver */ ret = register_driver(devpath, &g_ws2812fops, 0666, priv); if (ret < 0) { lederr("ERROR: Failed to register driver: %d\n", ret); kmm_free(priv->tx_buf); kmm_free(priv); } return ret; } #endif /* CONFIG_WS2812 */