/************************************************************************************
 * configs/sama5d3x-ek/src/sam_norflash.c
 *
 *   Copyright (C) 2013 Gregory Nutt. All rights reserved.
 *   Author: Gregory Nutt <gnutt@nuttx.org>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ************************************************************************************/

/************************************************************************************
 * Included Files
 ************************************************************************************/

#include <nuttx/config.h>

#include <debug.h>

#include "sama5d3x-ek.h"

#ifdef CONFIG_SAMA5_BOOT_CS0FLASH

/************************************************************************************
 * Definitions
 ************************************************************************************/

/************************************************************************************
 * Private Functions
 ************************************************************************************/

/************************************************************************************
 * Public Functions
 ************************************************************************************/

/****************************************************************************
 * Name: board_norflash_config
 *
 * Description:
 *   If CONFIG_SAMA5_BOOT_CS0FLASH, then the system is boot directly off
 *   CS0 NOR FLASH.  In this case, we assume that we get here from the
 *   primary boot loader under these conditions:
 *
 *     "If BMS signal is tied to 0, BMS_BIT is read at 1.  The ROM Code
 *      allows execution of the code contained into the memory connected to
 *      Chip Select 0 of the External Bus Interface.
 *
 *     "To achieve that, the following sequence is preformed by the ROM
 *      Code:
 *
 *        - The main clock is the on-chip 12 MHz RC oscillator,
 *        - The Static Memory Controller is configured with timing allowing
 *          code execution inCS0 external memory at 12 MHz
 *        - AXI matrix is configured to remap EBI CS0 address at 0x0
 *        - 0x0 is loaded in the Program Counter register
 *
 *     "The user software in the external memory must perform the next
 *      operation in order to complete the clocks and SMC timings
 *      configuration to run at a higher clock frequency:
 *
 *        - Enable the 32768 Hz oscillator if best accuracy is needed
 *        - Reprogram the SMC setup, cycle, hold, mode timing registers
 *          for EBI CS0, to adapt them to the new clock
 *        - Program the PMC (Main Oscillator Enable or Bypass mode)
 *        - Program and Start the PLL
 *        - Switch the system clock to the new value"
 *
 *   This function provides the board-specific implementation of the logic
 *   to reprogram the SMC.
 *
 ****************************************************************************/

void board_norflash_config(void)
{
#warning Missing logic
}

#endif /* CONFIG_SAMA5_BOOT_CS0FLASH */