/**************************************************************************** * drivers/net/w5500.c * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /**************************************************************************** * References: * [W5500] W5500 Datasheet, Version 1.0.9, May 2019, WIZnet Co., Ltd. ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #ifdef CONFIG_NET_PKT # include #endif #ifdef CONFIG_NET_W5500 /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Work queue support is required. */ #if !defined(CONFIG_SCHED_WORKQUEUE) # error Work queue support is required in this configuration (CONFIG_SCHED_WORKQUEUE) #else /* The low priority work queue is preferred. If it is not enabled, LPWORK * will be the same as HPWORK. * * NOTE: However, the network should NEVER run on the high priority work * queue! That queue is intended only to service short back end interrupt * processing that never suspends. Suspending the high priority work queue * may bring the system to its knees! */ #define ETHWORK LPWORK /* CONFIG_NET_W5500_NINTERFACES determines the number of physical interfaces * that will be supported. */ #ifndef CONFIG_NET_W5500_NINTERFACES # define CONFIG_NET_W5500_NINTERFACES 1 #endif /* TX timeout = 1 minute * CLK_TCK is the number of clock ticks per second */ #define W5500_TXTIMEOUT (60 * CLK_TCK) /* Packet buffer size */ #define PKTBUF_SIZE (MAX_NETDEV_PKTSIZE + CONFIG_NET_GUARDSIZE) /* This is a helper pointer for accessing the contents of Ethernet header */ #define BUF ((FAR struct eth_hdr_s *)self->w_dev.d_buf) /* Number of Ethernet frame transmission buffers maintained in W5500's 16 KiB * Tx RAM. A maximum size is conservatively assumed per Ethernet frame in * order to simplify buffer management logic. */ #define NUM_TXBUFS ((16 * 1024) / (CONFIG_NET_ETH_PKTSIZE)) /* W5500 SPI Host Interface *************************************************/ #define W5500_BSB_COMMON_REGS 0x00u #define W5500_BSB_SOCKET_REGS(n) (((n & 0x7u) << 5) | 0x08u) #define W5500_BSB_SOCKET_TX_BUFFER(n) (((n & 0x7u) << 5) | 0x10u) #define W5500_BSB_SOCKET_RX_BUFFER(n) (((n & 0x7u) << 5) | 0x18u) #define W5500_RWB_READ 0x00u #define W5500_RWB_WRITE 0x04u #define W5500_OM_DATA_LEN_VAR 0x00u #define W5500_OM_DATA_LEN_1 0x01u #define W5500_OM_DATA_LEN_2 0x02u #define W5500_OM_DATA_LEN_4 0x03u /* W5500 Register Addresses *************************************************/ /* Common Register Block */ #define W5500_MR 0x0000 /* Mode */ #define W5500_GAR0 0x0001 /* Gateway Address */ #define W5500_GAR1 0x0002 #define W5500_GAR2 0x0003 #define W5500_GAR3 0x0004 #define W5500_SUBR0 0x0005 /* Subnet Mask Address */ #define W5500_SUBR1 0x0006 #define W5500_SUBR2 0x0007 #define W5500_SUBR3 0x0008 #define W5500_SHAR0 0x0009 /* Source Hardware Address */ #define W5500_SHAR1 0x000a #define W5500_SHAR2 0x000b #define W5500_SHAR3 0x000c #define W5500_SHAR4 0x000d #define W5500_SHAR5 0x000e #define W5500_SIPR0 0x000f /* Source IP Address */ #define W5500_SIPR1 0x0010 #define W5500_SIPR2 0x0011 #define W5500_SIPR3 0x0012 #define W5500_INTLEVEL0 0x0013 /* Interrupt Low Level Timer */ #define W5500_INTLEVEL1 0x0014 #define W5500_IR 0x0015 /* Interrupt */ #define W5500_IMR 0x0016 /* Interrupt Mask */ #define W5500_SIR 0x0017 /* Socket Interrupt */ #define W5500_SIMR 0x0018 /* Socket Interrupt Mask */ #define W5500_RTR0 0x0019 /* Retry Time */ #define W5500_RTR1 0x001a #define W5500_RCR 0x001b /* Retry Count */ #define W5500_PTIMER 0x001c /* PPP LCP Request Timer */ #define W5500_PMAGIC 0x001d /* PPP LCP Magic number */ #define W5500_PHAR0 0x001e /* PPP Destination MAC Address */ #define W5500_PHAR1 0x001f #define W5500_PHAR2 0x0020 #define W5500_PHAR3 0x0021 #define W5500_PHAR4 0x0022 #define W5500_PHAR5 0x0023 #define W5500_PSID0 0x0024 /* PPP Session Identification */ #define W5500_PSID1 0x0025 #define W5500_PMRU0 0x0026 /* PPP Maximum Segment Size */ #define W5500_PMRU1 0x0027 #define W5500_UIPR0 0x0028 /* Unreachable IP address */ #define W5500_UIPR1 0x0029 #define W5500_UIPR2 0x002a #define W5500_UIPR3 0x002b #define W5500_UPORTR0 0x002c /* Unreachable Port */ #define W5500_UPORTR1 0x002d #define W5500_PHYCFGR 0x002e /* PHY Configuration */ /* 0x002f-0x0038: Reserved */ #define W5500_VERSIONR 0x0039 /* Chip version */ /* 0x003a-0xffff: Reserved */ /* Socket Register Block */ #define W5500_SN_MR 0x0000 /* Socket n Mode */ #define W5500_SN_CR 0x0001 /* Socket n Command */ #define W5500_SN_IR 0x0002 /* Socket n Interrupt */ #define W5500_SN_SR 0x0003 /* Socket n Status */ #define W5500_SN_PORT0 0x0004 /* Socket n Source Port */ #define W5500_SN_PORT1 0x0005 #define W5500_SN_DHAR0 0x0006 /* Socket n Destination Hardware Address */ #define W5500_SN_DHAR1 0x0007 #define W5500_SN_DHAR2 0x0008 #define W5500_SN_DHAR3 0x0009 #define W5500_SN_DHAR4 0x000a #define W5500_SN_DHAR5 0x000b #define W5500_SN_DIPR0 0x000c /* Socket n Destination IP Address */ #define W5500_SN_DIPR1 0x000d #define W5500_SN_DIPR2 0x000e #define W5500_SN_DIPR3 0x000f #define W5500_SN_DPORT0 0x0010 /* Socket n Destination Port */ #define W5500_SN_DPORT1 0x0011 #define W5500_SN_MSSR0 0x0012 /* Socket n Maximum Segment Size */ #define W5500_SN_MSSR1 0x0013 /* 0x0014: Reserved */ #define W5500_SN_TOS 0x0015 /* Socket n IP TOS */ #define W5500_SN_TTL 0x0016 /* Socket n IP TTL */ /* 0x0017-0x001d: Reserved */ #define W5500_SN_RXBUF_SIZE 0x001e /* Socket n Receive Buffer Size */ #define W5500_SN_TXBUF_SIZE 0x001f /* Socket n Transmit Buffer Size */ #define W5500_SN_TX_FSR0 0x0020 /* Socket n TX Free Size */ #define W5500_SN_TX_FSR1 0x0021 #define W5500_SN_TX_RD0 0x0022 /* Socket n TX Read Pointer */ #define W5500_SN_TX_RD1 0x0023 #define W5500_SN_TX_WR0 0x0024 /* Socket n TX Write Pointer */ #define W5500_SN_TX_WR1 0x0025 #define W5500_SN_RX_RSR0 0x0026 /* Socket n RX Received Size */ #define W5500_SN_RX_RSR1 0x0027 #define W5500_SN_RX_RD0 0x0028 /* Socket n RX Read Pointer */ #define W5500_SN_RX_RD1 0x0029 #define W5500_SN_RX_WR0 0x002a /* Socket n RX Write Pointer */ #define W5500_SN_RX_WR1 0x002b #define W5500_SN_IMR 0x002c /* Socket n Interrupt Mask */ #define W5500_SN_FRAG0 0x002d /* Socket n Fragment Offset in IP header */ #define W5500_SN_FRAG1 0x002e #define W5500_SN_KPALVTR 0x002f /* Keep alive timer */ /* 0x0030-0xffff: Reserved */ /* W5500 Register Bitfield Definitions **************************************/ /* Common Register Block */ /* Mode Register (MR) */ #define MR_FARP (1 << 1) /* Bit 1: Force ARP */ #define MR_PPPOE (1 << 3) /* Bit 3: PPPoE Mode */ #define MR_PB (1 << 4) /* Bit 4: Ping Block Mode */ #define MR_WOL (1 << 5) /* Bit 5: Wake on LAN */ #define MR_RST (1 << 7) /* Bit 7: Reset registers */ /* Interrupt Register (IR), Interrupt Mask Register (IMR) */ #define INT_MP (1 << 4) /* Bit 4: Magic Packet */ #define INT_PPPOE (1 << 5) /* Bit 5: PPPoE Connection Close */ #define INT_UNREACH (1 << 6) /* Bit 6: Destination unreachable */ #define INT_CONFLICT (1 << 7) /* Bit 7: IP Conflict */ /* Socket Interrupt Register (SIR) */ #define SIR(n) (1 << (n)) /* Socket Interrupt Mask Register (SIMR)) */ #define SIMR(n) (1 << (n)) /* PHY Configuration Register (PHYCFGR) */ #define PHYCFGR_LNK (1 << 0) /* Bit 0: Link Status */ #define PHYCFGR_SPD (1 << 1) /* Bit 1: Speed Status */ #define PHYCFGR_DPX (1 << 2) /* Bit 2: Duplex Status */ #define PHYCFGR_OPMDC_SHIFT (3) /* Bits 3-5: Operation Mode Configuration */ #define PHYCFGR_OPMDC_MASK (7 << PHYCFGR_OPMDC_SHIFT) # define PHYCFGR_OPMDC_10BT_HD_NAN (0 << PHYCFGR_OPMDC_SHIFT) /* 10BT Half-duplex */ # define PHYCFGR_OPMDC_10BT_HFD_NAN (1 << PHYCFGR_OPMDC_SHIFT) /* 10BT Full-duplex */ # define PHYCFGR_OPMDC_100BT_HD_NAN (2 << PHYCFGR_OPMDC_SHIFT) /* 100BT Half-duplex */ # define PHYCFGR_OPMDC_10BT_FD_NAN (3 << PHYCFGR_OPMDC_SHIFT) /* 100BT Full-duplex, * Auto-negotiation */ # define PHYCFGR_OPMDC_100BT_HD_AN (4 << PHYCFGR_OPMDC_SHIFT) /* 100BT Half-duplex, * Auto-negotiation */ # define PHYCFGR_OPMDC_POWER_DOWN (6 << PHYCFGR_OPMDC_SHIFT) /* Power Down mode */ # define PHYCFGR_OPMDC_ALLCAP_AN (7 << PHYCFGR_OPMDC_SHIFT) /* All capable, * Auto-negotiation */ #define PHYCFGR_OPMD (1 << 6) /* Bit 6: Configure PHY Operation Mode */ #define PHYCFGR_RST (1 << 7) /* Bit 7: Reset */ /* Socket Register Block */ /* Socket n Mode Register (SN_MR) */ #define SN_MR_PROTOCOL_SHIFT (0) /* Bits 0-3: Protocol */ #define SN_MR_PROTOCOL_MASK (15 << SN_MR_PROTOCOL_SHIFT) # define SN_MR_P0 (1 << (SN_MR_PROTOCOL_SHIFT + 0)) # define SN_MR_P1 (1 << (SN_MR_PROTOCOL_SHIFT + 1)) # define SN_MR_P2 (1 << (SN_MR_PROTOCOL_SHIFT + 2)) # define SN_MR_P3 (1 << (SN_MR_PROTOCOL_SHIFT + 3)) # define SM_MR_CLOSED 0 # define SM_MR_TCP SN_MR_P0 # define SM_MR_UDP SN_MR_P1 # define SM_MR_MACRAW SN_MR_P2 #define SN_MR_UCASTB (1 << 4) /* Bit 4: UNICAST Blocking in UDP mode */ #define SN_MR_MIP6B (1 << 4) /* Bit 4: IPv6 packet Blocking in MACRAW mode */ #define SN_MR_ND (1 << 5) /* Bit 5: Use No Delayed ACK */ #define SN_MR_MC (1 << 5) /* Bit 5: Multicast */ #define SN_MR_MMB (1 << 5) /* Bit 5: Multicast Blocking in MACRAW mode */ #define SN_MR_BCASTB (1 << 6) /* Bit 6: Broadcast Blocking in MACRAW and * UDP mode */ #define SN_MR_MULTI (1 << 7) /* Bit 7: Multicasting in UDP mode */ #define SN_MR_MFEN (1 << 7) /* Bit 7: MAC Filter Enable in MACRAW mode */ /* Socket n Command Register (SN_CR) */ #define SN_CR_OPEN 0x01 /* Socket n is initialized and opened according * to the protocol selected in SN_MR */ #define SN_CR_LISTEN 0x02 /* Socket n operates as a 'TCP server' and waits * for connection request from any 'TCP client' */ #define SN_CR_CONNECT 0x04 /* 'TCP client' connection request */ #define SN_CR_DISCON 0x08 /* TCP disconnection request */ #define SN_CR_CLOSE 0x10 /* Close socket n */ #define SN_CR_SEND 0x20 /* Transmit all data in Socket n TX buffer */ #define SN_CR_SEND_MAC 0x21 /* Transmit all UDP data (no ARP) */ #define SN_CR_SEND_KEEP 0x22 /* Send TCP keep-alive packet */ #define SN_CR_RECV 0x40 /* Complete received data in Socket n RX buffer */ /* Socket n Interrupt Register (SN_IR) and * Socket n Interrupt Mask Register (SN_IMR) */ #define SN_INT_CON (1 << 0) /* Bit 0: Connection with peer successful */ #define SN_INT_DISCON (1 << 1) /* Bit 1: FIN or FIN/ACK received from peer */ #define SN_INT_RECV (1 << 2) /* Bit 2: Data received from peer */ #define SN_INT_TIMEOUT (1 << 3) /* Bit 3: ARP or TCP timeout */ #define SN_INT_SEND_OK (1 << 4) /* Bit 4: SEND command completed */ /* Socket n Status Register (SN_SR) */ #define SN_SR_SOCK_CLOSED 0x00 #define SN_SR_SOCK_INIT 0x13 #define SN_SR_SOCK_LISTEN 0x14 #define SN_SR_SOCK_ESTABLISHED 0x17 #define SN_SR_SOCK_CLOSE_WAIT 0x1c #define SN_SR_SOCK_UDP 0x22 #define SN_SR_SOCK_MACRAW 0x42 #define SN_SR_SOCK_SYNSENT 0x15 /* Transitional status */ #define SN_SR_SOCK_SYNRECV 0x16 #define SN_SR_SOCK_FIN_WAIT 0x18 #define SN_SR_SOCK_CLOSING 0x1a #define SN_SR_SOCK_TIME_WAIT 0x1b #define SN_SR_SOCK_LAST_ACK 0x1d /* Socket n RX Buffer Size Register (SN_RXBUF) */ #define SN_RXBUF_0KB 0 #define SN_RXBUF_1KB 1 #define SN_RXBUF_2KB 2 #define SN_RXBUF_4KB 4 #define SN_RXBUF_8KB 5 #define SN_RXBUF_16KB 16 /* Socket n TX Buffer Size Register (SN_TXBUF) */ #define SN_TXBUF_0KB 0 #define SN_TXBUF_1KB 1 #define SN_TXBUF_2KB 2 #define SN_TXBUF_4KB 4 #define SN_TXBUF_8KB 5 #define SN_TXBUF_16KB 16 /**************************************************************************** * Private Types ****************************************************************************/ /* The w5500_driver_s encapsulates all state information for a single * hardware interface */ struct w5500_driver_s { bool w_bifup; /* true:ifup false:ifdown */ struct wdog_s w_txtimeout; /* TX timeout timer */ struct work_s w_irqwork; /* For deferring interrupt work to the work queue */ struct work_s w_pollwork; /* For deferring poll work to the work queue */ /* Ethernet frame transmission buffer management */ uint16_t txbuf_offset[NUM_TXBUFS + 1]; uint8_t txbuf_rdptr; uint8_t txbuf_wrptr; /* The hardware interconnect to the W5500 chip */ FAR struct spi_dev_s *spi_dev; /* SPI hardware access */ FAR const struct w5500_lower_s *lower; /* Low-level MCU specific */ /* This holds the information visible to the NuttX network */ struct net_driver_s w_dev; /* Interface understood by the network */ }; /**************************************************************************** * Private Data ****************************************************************************/ /* A single packet buffer is used */ static uint16_t g_pktbuf[CONFIG_NET_W5500_NINTERFACES] [(PKTBUF_SIZE + 1) / 2]; /* Driver state structure */ static struct w5500_driver_s g_w5500[CONFIG_NET_W5500_NINTERFACES]; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ /* Common TX logic */ static void w5500_transmit(FAR struct w5500_driver_s *priv); static int w5500_txpoll(FAR struct net_driver_s *dev); /* Interrupt handling */ static void w5500_reply(FAR struct w5500_driver_s *priv); static void w5500_receive(FAR struct w5500_driver_s *priv); static void w5500_txdone(FAR struct w5500_driver_s *priv); static void w5500_interrupt_work(FAR void *arg); static int w5500_interrupt(int irq, FAR void *context, FAR void *arg); /* Watchdog timer expirations */ static void w5500_txtimeout_work(FAR void *arg); static void w5500_txtimeout_expiry(wdparm_t arg); /* NuttX callback functions */ static int w5500_ifup(FAR struct net_driver_s *dev); static int w5500_ifdown(FAR struct net_driver_s *dev); static void w5500_txavail_work(FAR void *arg); static int w5500_txavail(FAR struct net_driver_s *dev); #if defined(CONFIG_NET_MCASTGROUP) || defined(CONFIG_NET_ICMPv6) static int w5500_addmac(FAR struct net_driver_s *dev, FAR const uint8_t *mac); #ifdef CONFIG_NET_MCASTGROUP static int w5500_rmmac(FAR struct net_driver_s *dev, FAR const uint8_t *mac); #endif #ifdef CONFIG_NET_ICMPv6 static void w5500_ipv6multicast(FAR struct w5500_driver_s *priv); #endif #endif #ifdef CONFIG_NETDEV_IOCTL static int w5500_ioctl(FAR struct net_driver_s *dev, int cmd, unsigned long arg); #endif /**************************************************************************** * Private Functions ****************************************************************************/ /* Hardware interface to W5500 **********************************************/ /**************************************************************************** * Name: w5500_reset * * Description: * Apply the hardware reset sequence to the W5500 (See [W5500], section * 5.5.1 Reset Timing). Optinonally, keep hardware reset asserted. * * Input Parameters: * self - The respective w5500 device * keep - Whether the hardware reset shall be left asserted. * * Assumptions: * This function must only be called in interrupt context, if argument * keep is set to false (otherwise it sleeps, which is not allowed in * interrupt context). * ****************************************************************************/ static void w5500_reset(FAR struct w5500_driver_s *self, bool keep) { self->lower->reset(self->lower, true); if (!keep) { nxsig_usleep(500); /* [W5500]: T_RC (Reset Cycle Time) min 500 us */ self->lower->reset(self->lower, false); nxsig_usleep(1000); /* [W5500]: T_PL (RSTn to internal PLL lock) 1ms */ } } /**************************************************************************** * Name: w5500_lock * * Description: * Acquire exclusive access to the W5500's SPI bus and configure it * accordingly. * * Input Parameters: * self - The respective w5500 device * ****************************************************************************/ static void w5500_lock(FAR struct w5500_driver_s *self) { int ret; ret = SPI_LOCK(self->spi_dev, true); DEBUGASSERT(ret == OK); SPI_SETMODE(self->spi_dev, self->lower->mode); SPI_SETBITS(self->spi_dev, 8); SPI_HWFEATURES(self->spi_dev, 0); SPI_SETFREQUENCY(self->spi_dev, self->lower->frequency); SPI_SELECT(self->spi_dev, SPIDEV_ETHERNET(self->lower->spidevid), true); } /**************************************************************************** * Name: w5500_unlock * * Description: * Relinquish exclusive access to the W5500's SPI bus * * Input Parameters: * self - The respective w5500 device * ****************************************************************************/ static void w5500_unlock(FAR struct w5500_driver_s *self) { int ret; SPI_SELECT(self->spi_dev, SPIDEV_ETHERNET(self->lower->spidevid), false); ret = SPI_LOCK(self->spi_dev, false); DEBUGASSERT(ret == OK); } /**************************************************************************** * Name: w5500_read * * Description: * Read a number of bytes from one of the W5500's register or buffer * blocks. * * Input Parameters: * self - The respective w5500 device * block_select_bits - Register or buffer block to read from * offset - The offset address within the block * buffer - Buffer to copy read data into * len - Number of bytes to read from block * ****************************************************************************/ static void w5500_read(FAR struct w5500_driver_s *self, uint8_t block_select_bits, uint16_t offset, FAR void *buffer, uint16_t len) { uint8_t addr_cntl[3]; addr_cntl[0] = (uint8_t)(offset >> 8); addr_cntl[1] = (uint8_t)offset; addr_cntl[2] = block_select_bits | W5500_RWB_READ | W5500_OM_DATA_LEN_VAR; w5500_lock(self); SPI_SNDBLOCK(self->spi_dev, addr_cntl, sizeof(addr_cntl)); SPI_RECVBLOCK(self->spi_dev, buffer, len); w5500_unlock(self); } /**************************************************************************** * Name: w5500_write * * Description: * Write a number of bytes to one of the W5500's register or buffer * blocks. * * Input Parameters: * self - The respective w5500 device * block_select_bits - Register or buffer block to read from * offset - The offset address within the block * Data - Data to write to block * len - Number of bytes to write to block * ****************************************************************************/ static void w5500_write(FAR struct w5500_driver_s *self, uint8_t block_select_bits, off_t offset, FAR const void *data, size_t len) { uint8_t addr_cntl[3]; addr_cntl[0] = (uint8_t)(offset >> 8); addr_cntl[1] = (uint8_t)offset; addr_cntl[2] = block_select_bits | W5500_RWB_WRITE | W5500_OM_DATA_LEN_VAR; w5500_lock(self); SPI_SNDBLOCK(self->spi_dev, addr_cntl, sizeof(addr_cntl)); SPI_SNDBLOCK(self->spi_dev, data, len); w5500_unlock(self); } /**************************************************************************** * Name: w5500_read8 * * Description: * Read a single byte from one of the W5500's register or buffer blocks. * * Input Parameters: * self - The respective w5500 device * block_select_bits - Register or buffer block to read from * offset - The offset address within the block * * Returned Value: * The byte read * ****************************************************************************/ static uint8_t w5500_read8(FAR struct w5500_driver_s *self, uint8_t block_select_bits, uint16_t offset) { uint8_t value; w5500_read(self, block_select_bits, offset, &value, sizeof(value)); return value; } /**************************************************************************** * Name: w5500_write8 * * Description: * Write a single byte to one of the W5500's register or buffer blocks. * * Input Parameters: * self - The respective w5500 device * block_select_bits - Register or buffer block to read from * offset - The offset address within the block * value - The byte value to write * ****************************************************************************/ static void w5500_write8(FAR struct w5500_driver_s *self, uint8_t block_select_bits, uint16_t offset, uint8_t value) { w5500_write(self, block_select_bits, offset, &value, sizeof(value)); } /**************************************************************************** * Name: w5500_read16 * * Description: * Read a two byte value from one of the W5500's register or buffer blocks. * * Input Parameters: * self - The respective w5500 device * block_select_bits - Register or buffer block to read from * offset - The offset address within the block * * Returned Value: * The two byte value read in host byte order. * ****************************************************************************/ static uint16_t w5500_read16(FAR struct w5500_driver_s *self, uint8_t block_select_bits, uint16_t offset) { uint16_t value; w5500_read(self, block_select_bits, offset, &value, sizeof(value)); return NTOHS(value); } /**************************************************************************** * Name: w5500_write16 * * Description: * Write a two byte value to one of the W5500's register or buffer blocks. * * Input Parameters: * self - The respective w5500 device * block_select_bits - Register or buffer block to read from * offset - The offset address within the block * value - The two byte value to write in host byte order. * ****************************************************************************/ static void w5500_write16(FAR struct w5500_driver_s *self, uint8_t block_select_bits, uint16_t offset, uint16_t value) { value = HTONS(value); w5500_write(self, block_select_bits, offset, &value, sizeof(value)); } /**************************************************************************** * Name: w5500_read16_atomic * * Description: * Read a two-byte value that is concurrently updated by the W5500 hardware * in a safe fashion. In [W5500] it is recommended to read the 16 bits * multiple times until one gets the same value twice in a row. * * Input Parameters: * self - The respective w5500 device * block_select_bits - Register block to read from (See [W5500], section * 2.2.2 Control Phase) * offset - Offset address of the register to read. * value - The 16-bit value read in host byte-order. * * Returned Value: * OK in case of success. A negated errno value in case of failure. * ****************************************************************************/ static int w5500_read16_atomic(FAR struct w5500_driver_s *self, uint8_t block_select_bits, uint16_t offset, FAR uint16_t *value) { int i; *value = w5500_read16(self, block_select_bits, offset); for (i = 0; i < 100; i++) { uint16_t temp; temp = w5500_read16(self, block_select_bits, offset); if (*value == temp) { return OK; } *value = temp; } nerr("Failed to get consistent value.\n"); return -EIO; } /* Ethernet frame transmission buffer management ****************************/ /**************************************************************************** * Name: w5500_txbuf_reset * * Description: * Reset state that manages the storage of multiple outgoing Ethernet * frames in W5500's 16KiB Tx RAM. * * Input Parameters: * self - The respective w5500 device * ****************************************************************************/ static void w5500_txbuf_reset(FAR struct w5500_driver_s *self) { memset(self->txbuf_offset, 0, sizeof(self->txbuf_offset)); self->txbuf_rdptr = 0; self->txbuf_wrptr = 0; } /**************************************************************************** * Name: w5500_txbuf_numfree * * Description: * Return the number of Ethernet frames that can still be stored in W5500's * 16KiB Tx RAM. * * Input Parameters: * self - The respective w5500 device * * Returned Value: * The number of Ethernet frames that can still be stored. * ****************************************************************************/ static int w5500_txbuf_numfree(FAR struct w5500_driver_s *self) { if (self->txbuf_wrptr >= self->txbuf_rdptr) { return NUM_TXBUFS - (self->txbuf_wrptr - self->txbuf_rdptr); } else { return self->txbuf_rdptr - self->txbuf_wrptr - 1; } } /**************************************************************************** * Name: w5500_txbuf_numpending * * Description: * Return the number of Ethernet frames that are still pending for trans- * mission from W5500's 16KiB Tx RAM. * * Input Parameters: * self - The respective w5500 device * * Returned Value: * The number of Ethernet frames that are pending for transmission. * ****************************************************************************/ static int w5500_txbuf_numpending(FAR struct w5500_driver_s *self) { return NUM_TXBUFS - w5500_txbuf_numfree(self); } /**************************************************************************** * Name: w5500_txbuf_copy * * Description: * Copy an Ethernet frame from the socket device's buffer to the W5500's * 16KiB Tx RAM. * * Input Parameters: * self - The respective w5500 device * * Returned Value: * The byte offset of the first byte after the frame that was copied into * W5500's 16KiB Tx RAM. * ****************************************************************************/ static uint16_t w5500_txbuf_copy(FAR struct w5500_driver_s *self) { uint16_t offset; DEBUGASSERT(w5500_txbuf_numfree(self) > 0); offset = self->txbuf_offset[self->txbuf_wrptr]; w5500_write(self, W5500_BSB_SOCKET_TX_BUFFER(0), offset, self->w_dev.d_buf, self->w_dev.d_len); self->txbuf_wrptr = (self->txbuf_wrptr + 1) % (NUM_TXBUFS + 1); self->txbuf_offset[self->txbuf_wrptr] = offset + self->w_dev.d_len; return self->txbuf_offset[self->txbuf_wrptr]; } /**************************************************************************** * Name: w5500_txbuf_next * * Description: * Release storage for an Ethernet frame that has been successfully * transmitted. Also triggers transmission of the next Ethernet frame, * if applicable. * * Input Parameters: * self - The respective w5500 device * * Returned Value: * Whether transmission of another Ethernet frame was triggered. * ****************************************************************************/ static bool w5500_txbuf_next(FAR struct w5500_driver_s *self) { uint16_t offset; DEBUGASSERT(w5500_txbuf_numpending(self)); self->txbuf_rdptr = (self->txbuf_rdptr + 1) % (NUM_TXBUFS + 1); offset = w5500_read16(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_TX_RD0); DEBUGASSERT(self->txbuf_offset[self->txbuf_rdptr] == offset); if (!w5500_txbuf_numpending(self)) { return false; } offset = self->txbuf_offset[(self->txbuf_rdptr + 1) % (NUM_TXBUFS + 1)]; w5500_write16(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_TX_WR0, offset); w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_CR, SN_CR_SEND); /* (Re-)start the TX timeout watchdog timer */ wd_start(&self->w_txtimeout, W5500_TXTIMEOUT, w5500_txtimeout_expiry, (wdparm_t)self); return true; } /**************************************************************************** * Name: w5500_fence * * Description: * Put the W5500 into reset and disable respective interrupt handling. * * Input Parameters: * self - The respective w5500 device * ****************************************************************************/ static void w5500_fence(FAR struct w5500_driver_s *self) { self->lower->enable(self->lower, false); w5500_reset(self, true); /* Reset and keep reset asserted */ self->w_bifup = false; } /**************************************************************************** * Name: w5500_unfence * * Description: * Release W5500 from reset, initialize it and wait up to ten seconds * for link up. * * Input Parameters: * self - The respective w5500 device * * Returned Value: * OK in case of success. A negated errno value in case of failure, in * which case the W5500 is fenced again. * ****************************************************************************/ static int w5500_unfence(FAR struct w5500_driver_s *self) { uint8_t value; int i; /* Initialize PHYs, Ethernet interface, and setup up Ethernet interrupts */ w5500_reset(self, false); /* Reset sequence and keep reset de-asserted */ /* Set the Ethernet interface's MAC address */ w5500_write(self, W5500_BSB_COMMON_REGS, W5500_SHAR0, /* Source Hardware Address Register */ self->w_dev.d_mac.ether.ether_addr_octet, sizeof(self->w_dev.d_mac.ether.ether_addr_octet)); /* Configure socket 0 for raw MAC access with MAC filtering enabled. */ w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_MR, SM_MR_MACRAW | SN_MR_MFEN); /* Allocate all TX and RX buffer space to socket 0 ... */ w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_RXBUF_SIZE, SN_RXBUF_16KB); w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_TXBUF_SIZE, SN_TXBUF_16KB); /* ... and none to sockets 1 to 7. */ for (i = 1; i < 8; i++) { w5500_write8(self, W5500_BSB_SOCKET_REGS(i), W5500_SN_RXBUF_SIZE, SN_RXBUF_0KB); w5500_write8(self, W5500_BSB_SOCKET_REGS(i), W5500_SN_TXBUF_SIZE, SN_TXBUF_0KB); } /* Enable RECV interrupts on socket 0 (SEND_OK interrupts will only be * enabled as long as a transmission is in progress). */ w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_IMR, SN_INT_RECV); /* Enable interrupts on socket 0 */ w5500_write8(self, W5500_BSB_COMMON_REGS, W5500_SIMR, /* Socket Interrupt Mask Register */ SIMR(0)); /* Open socket 0 */ w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_CR, /* Control Register */ SN_CR_OPEN); /* Check whether socket 0 is open in MACRAW mode. */ value = w5500_read8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_SR); if (value != SN_SR_SOCK_MACRAW) { nerr("Unexpected status: %02" PRIx8 "\n", value); goto error; } /* Reset Tx buffer management state. */ w5500_txbuf_reset(self); /* Wait up to 10 seconds for link-up */ value = w5500_read8(self, W5500_BSB_COMMON_REGS, W5500_PHYCFGR); for (i = 0; (i < 100) && !(value & PHYCFGR_LNK); i++) { value = w5500_read8(self, W5500_BSB_COMMON_REGS, W5500_PHYCFGR); nxsig_usleep(100000); /* 100 ms x 100 = 10 sec */ } if (value & PHYCFGR_LNK) { ninfo("Link up (%d Mbps / %s duplex)\n", (value & PHYCFGR_SPD) ? 100 : 10, (value & PHYCFGR_DPX) ? "full" : "half"); } else { nwarn("Link still down. Cable plugged?\n"); goto error; } return OK; error: w5500_fence(self); return -EIO; } /**************************************************************************** * Name: w5500_transmit * * Description: * Start hardware transmission. Called either from the txdone interrupt * handling or from watchdog based polling. * * Input Parameters: * priv - Reference to the driver state structure * * Returned Value: * OK on success; a negated errno on failure * * Assumptions: * The network is locked. * ****************************************************************************/ static void w5500_transmit(FAR struct w5500_driver_s *self) { uint16_t offset; /* Verify that the hardware is ready to send another packet. If we get * here, then we are committed to sending a packet; Higher level logic * must have assured that there is no transmission in progress. */ if (!w5500_txbuf_numfree(self)) { ninfo("Dropping Tx packet due to no buffer available.\n"); NETDEV_TXERRORS(self->w_dev); return; } /* Increment statistics */ NETDEV_TXPACKETS(self->w_dev); /* Copy packet data to TX buffer */ offset = w5500_txbuf_copy(self); /* If there have not been any Tx buffers in use this means we need to start * transmission. Otherwise, this is done either in w5500_txdone or in * w5500_txtimeout_work. */ if (w5500_txbuf_numpending(self) == 1) { /* Set TX Write Pointer to indicate packet length */ w5500_write16(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_TX_WR0, offset); /* Enable Tx interrupts (Rx ones are always enabled). */ w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_IMR, SN_INT_RECV | SN_INT_SEND_OK); /* Send the packet */ w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_CR, /* Control Register */ SN_CR_SEND); /* Setup the TX timeout watchdog (perhaps restarting the timer) */ wd_start(&self->w_txtimeout, W5500_TXTIMEOUT, w5500_txtimeout_expiry, (wdparm_t)self); } #ifdef CONFIG_DEBUG_NET_INFO ninfodumpbuffer("Transmitted:", self->w_dev.d_buf, self->w_dev.d_len); #endif } /**************************************************************************** * Name: w5500_txpoll * * Description: * The transmitter is available, check if the network has any outgoing * packets ready to send. This is a callback from devif_poll(). * devif_poll() may be called: * * 1. When the preceding TX packet send is complete, * 2. When the preceding TX packet send timesout and the interface is reset * 3. During normal TX polling * * Input Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * OK on success; a negated errno on failure * * Assumptions: * The network is locked. * ****************************************************************************/ static int w5500_txpoll(FAR struct net_driver_s *dev) { FAR struct w5500_driver_s *self = (FAR struct w5500_driver_s *)dev->d_private; /* Send the packet */ w5500_transmit(self); /* Check if there is room in the device to hold another packet. * If not, return a non-zero value to terminate the poll. */ return !w5500_txbuf_numfree(self); } /**************************************************************************** * Name: w5500_reply * * Description: * After a packet has been received and dispatched to the network, it * may return with an outgoing packet. This function checks for that case * and performs the transmission if necessary. * * Input Parameters: * self - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * The network is locked. * ****************************************************************************/ static void w5500_reply(FAR struct w5500_driver_s *self) { /* If the packet dispatch resulted in data that should be sent out on the * network, the field d_len will set to a value > 0. */ if (self->w_dev.d_len > 0) { /* And send the packet */ w5500_transmit(self); } } /**************************************************************************** * Name: w5500_receive * * Description: * An interrupt was received indicating the availability of a new RX packet * * Input Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * The network is locked. * ****************************************************************************/ static void w5500_receive(FAR struct w5500_driver_s *self) { do { uint16_t s0_rx_rd; uint16_t s0_rx_rsr; uint16_t pktlen; int ret; /* Check if the packet is a valid size for the network buffer * configuration. */ ret = w5500_read16_atomic(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_RX_RSR0, &s0_rx_rsr); if (ret != OK) { goto error; } if (s0_rx_rsr == 0) { ninfo("No data left to read. We are done.\n"); break; } /* The W5500 prepends each packet with a 2-byte length field in * network byte order. The length value includes the length field * itself. At least this 2-byte packet length must be available. */ if (s0_rx_rsr < sizeof(pktlen)) { nerr("Received size too small. S0_RX_RSR %"PRIu16"\n", s0_rx_rsr); goto error; } /* Get the Socket 0 RX Read Pointer. */ s0_rx_rd = w5500_read16(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_RX_RD0); /* Read 16-bit length field. */ pktlen = w5500_read16(self, W5500_BSB_SOCKET_RX_BUFFER(0), s0_rx_rd); if (pktlen > s0_rx_rsr) { nerr("Incomplete packet: pktlen %"PRIu16", S0_RX_RSR %"PRIu16"\n", pktlen, s0_rx_rd); goto error; } if (pktlen < s0_rx_rsr) { ninfo("More than one packet in RX buffer. " "pktlen %"PRIu16", S0_RX_RSR %"PRIu16"\n", pktlen, s0_rx_rsr); } self->w_dev.d_len = pktlen - sizeof(pktlen); /* Copy the data data from the hardware to priv->w_dev.d_buf. Set * amount of data in priv->w_dev.d_len */ if (self->w_dev.d_len <= CONFIG_NET_ETH_PKTSIZE) { w5500_read(self, W5500_BSB_SOCKET_RX_BUFFER(0), s0_rx_rd + sizeof(pktlen), self->w_dev.d_buf, self->w_dev.d_len); } /* Acknowledge data reception to W5500 */ w5500_write16(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_RX_RD0, s0_rx_rd + pktlen); w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_CR, SN_CR_RECV); /* Check for errors and update statistics */ if (self->w_dev.d_len > CONFIG_NET_ETH_PKTSIZE || self->w_dev.d_len < ETH_HDRLEN) { nerr("Bad packet size dropped (%"PRIu16")\n", self->w_dev.d_len); self->w_dev.d_len = 0; NETDEV_RXERRORS(&priv->dev); continue; } #ifdef CONFIG_DEBUG_NET_INFO ninfodumpbuffer("Received Packet:", self->w_dev.d_buf, self->w_dev.d_len); #endif #ifdef CONFIG_NET_PKT /* When packet sockets are enabled, feed the frame into the tap */ pkt_input(&self->w_dev); #endif #ifdef CONFIG_NET_IPv4 /* Check for an IPv4 packet */ if (BUF->type == HTONS(ETHTYPE_IP)) { ninfo("IPv4 frame\n"); NETDEV_RXIPV4(&self->w_dev); /* Receive an IPv4 packet from the network device */ ipv4_input(&self->w_dev); /* Check for a reply to the IPv4 packet */ w5500_reply(self); } else #endif #ifdef CONFIG_NET_IPv6 /* Check for an IPv6 packet */ if (BUF->type == HTONS(ETHTYPE_IP6)) { ninfo("IPv6 frame\n"); NETDEV_RXIPV6(&self->w_dev); /* Dispatch IPv6 packet to the network layer */ ipv6_input(&self->w_dev); /* Check for a reply to the IPv6 packet */ w5500_reply(self); } else #endif #ifdef CONFIG_NET_ARP /* Check for an ARP packet */ if (BUF->type == HTONS(ETHTYPE_ARP)) { ninfo("ARP frame\n"); /* Dispatch ARP packet to the network layer */ arp_input(&self->w_dev); NETDEV_RXARP(&self->w_dev); /* If the above function invocation resulted in data that should be * sent out on the network, the field d_len will set to a value * > 0. */ if (self->w_dev.d_len > 0) { w5500_transmit(self); } } else #endif { ninfo("Dropped frame\n"); NETDEV_RXDROPPED(&self->w_dev); } } while (true); /* While there are more packets to be processed */ return; error: w5500_fence(self); } /**************************************************************************** * Name: w5500_txdone * * Description: * An interrupt was received indicating that the last TX packet(s) is done * * Input Parameters: * priv - Reference to the driver state structure * * Returned Value: * None * * Assumptions: * The network is locked. * ****************************************************************************/ static void w5500_txdone(FAR struct w5500_driver_s *self) { /* Check for errors and update statistics */ NETDEV_TXDONE(self->w_dev); /* Check if there are pending transmissions. */ if (!w5500_txbuf_next(self)) { ninfo("No further transmissions pending.\n"); /* If no further transmissions are pending, then cancel the TX timeout * and disable further Tx interrupts. */ wd_cancel(&self->w_txtimeout); /* And disable further TX interrupts. */ w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_IMR, SN_INT_RECV); } /* In any event, poll the network for new TX data */ devif_poll(&self->w_dev, w5500_txpoll); } /**************************************************************************** * Name: w5500_interrupt_work * * Description: * Perform interrupt related work from the worker thread * * Input Parameters: * arg - The argument passed when work_queue() was called. * * Returned Value: * OK on success * * Assumptions: * Runs on a worker thread. * ****************************************************************************/ static void w5500_interrupt_work(FAR void *arg) { FAR struct w5500_driver_s *self = (FAR struct w5500_driver_s *)arg; uint8_t ir[3]; /* Lock the network and serialize driver operations if necessary. * NOTE: Serialization is only required in the case where the driver work * is performed on an LP worker thread and where more than one LP worker * thread has been configured. */ net_lock(); /* Process pending Ethernet interrupts. Read IR, MIR and SIR in one shot * to optimize latency, although MIR is not actually used. */ w5500_read(self, W5500_BSB_COMMON_REGS, W5500_IR, ir, sizeof(ir)); /* We expect none of the common (integrated network stack related) * interrupts and only interrupts from socket 0. */ if (ir[0] != 0) { nwarn("Ignoring unexpected interrupts. IR: 0x%02"PRIx8"\n", ir[0]); w5500_write8(self, W5500_BSB_COMMON_REGS, W5500_IR, ir[0]); } if (ir[2] & ~SIR(0)) { nwarn("Interrupt pending for unused socket. SIR: 0x%02"PRIx8"\n", ir[2]); goto error; } if (ir[2] == 0) { nwarn("Overinitiative interrupt work.\n"); goto done; } /* Get and clear interrupt status bits */ ir[0] = w5500_read8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_IR); if ((ir[0] == 0) || ir[0] & ~(SN_INT_RECV | SN_INT_SEND_OK)) { nerr("Unsupported socket interrupts: %02"PRIx8"\n", ir[0]); goto error; } w5500_write8(self, W5500_BSB_SOCKET_REGS(0), W5500_SN_IR, ir[0]); /* Handle interrupts according to status bit settings */ /* Check if a packet transmission just completed. If so, call * w5500_txdone. This may disable further Tx interrupts if there are no * pending transmissions. */ if (ir[0] & SN_INT_SEND_OK) { w5500_txdone(self); } /* Check if we received an incoming packet, if so, call w5500_receive() */ if (ir[0] & SN_INT_RECV) { w5500_receive(self); } done: net_unlock(); /* Re-enable Ethernet interrupts */ self->lower->enable(self->lower, true); return; error: w5500_fence(self); net_unlock(); } /**************************************************************************** * Name: w5500_interrupt * * Description: * Hardware interrupt handler * * Input Parameters: * irq - Number of the IRQ that generated the interrupt * context - Interrupt register state save info (architecture-specific) * * Returned Value: * OK on success * * Assumptions: * Runs in the context of a the Ethernet interrupt handler. Local * interrupts are disabled by the interrupt logic. * ****************************************************************************/ static int w5500_interrupt(int irq, FAR void *context, FAR void *arg) { FAR struct w5500_driver_s *self = (FAR struct w5500_driver_s *)arg; DEBUGASSERT(self != NULL); /* Disable further Ethernet interrupts. Because Ethernet interrupts are * also disabled if the TX timeout event occurs, there can be no race * condition here. */ self->lower->enable(self->lower, false); /* Schedule to perform the interrupt processing on the worker thread. */ work_queue(ETHWORK, &self->w_irqwork, w5500_interrupt_work, self, 0); return OK; } /**************************************************************************** * Name: w5500_txtimeout_work * * Description: * Perform TX timeout related work from the worker thread * * Input Parameters: * arg - The argument passed when work_queue() as called. * * Returned Value: * OK on success * ****************************************************************************/ static void w5500_txtimeout_work(FAR void *arg) { FAR struct w5500_driver_s *self = (FAR struct w5500_driver_s *)arg; /* Lock the network and serialize driver operations if necessary. * NOTE: Serialization is only required in the case where the driver work * is performed on an LP worker thread and where more than one LP worker * thread has been configured. */ net_lock(); /* Increment statistics and dump debug info */ NETDEV_TXTIMEOUTS(self->w_dev); /* Then reset the hardware */ if (w5500_unfence(self) == OK) { self->lower->enable(self->lower, true); /* Then poll the network for new XMIT data */ devif_poll(&self->w_dev, w5500_txpoll); } net_unlock(); } /**************************************************************************** * Name: w5500_txtimeout_expiry * * Description: * Our TX watchdog timed out. Called from the timer interrupt handler. * The last TX never completed. Reset the hardware and start again. * * Input Parameters: * arg - The argument * * Returned Value: * None * * Assumptions: * Runs in the context of a the timer interrupt handler. Local * interrupts are disabled by the interrupt logic. * ****************************************************************************/ static void w5500_txtimeout_expiry(wdparm_t arg) { FAR struct w5500_driver_s *self = (FAR struct w5500_driver_s *)arg; /* Disable further Ethernet interrupts. This will prevent some race * conditions with interrupt work. There is still a potential race * condition with interrupt work that is already queued and in progress. */ w5500_fence(self); /* Schedule to perform the TX timeout processing on the worker thread. */ work_queue(ETHWORK, &self->w_irqwork, w5500_txtimeout_work, self, 0); } /**************************************************************************** * Name: w5500_ifup * * Description: * NuttX Callback: Bring up the Ethernet interface when an IP address is * provided * * Input Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * None * * Assumptions: * The network is locked. * ****************************************************************************/ static int w5500_ifup(FAR struct net_driver_s *dev) { FAR struct w5500_driver_s *self = (FAR struct w5500_driver_s *)dev->d_private; int ret; #ifdef CONFIG_NET_IPv4 ninfo("Bringing up: %d.%d.%d.%d\n", (int)dev->d_ipaddr & 0xff, (int)(dev->d_ipaddr >> 8) & 0xff, (int)(dev->d_ipaddr >> 16) & 0xff, (int)dev->d_ipaddr >> 24); #endif #ifdef CONFIG_NET_IPv6 ninfo("Bringing up: %04x:%04x:%04x:%04x:%04x:%04x:%04x:%04x\n", dev->d_ipv6addr[0], dev->d_ipv6addr[1], dev->d_ipv6addr[2], dev->d_ipv6addr[3], dev->d_ipv6addr[4], dev->d_ipv6addr[5], dev->d_ipv6addr[6], dev->d_ipv6addr[7]); #endif /* Initialize PHYs, Ethernet interface, and setup up Ethernet interrupts */ ret = w5500_unfence(self); if (ret != OK) { return ret; } #ifdef CONFIG_NET_ICMPv6 /* Set up IPv6 multicast address filtering */ w5500_ipv6multicast(self); #endif /* Enable the Ethernet interrupt */ self->w_bifup = true; self->lower->enable(self->lower, true); return OK; } /**************************************************************************** * Name: w5500_ifdown * * Description: * NuttX Callback: Stop the interface. * * Input Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * None * * Assumptions: * The network is locked. * ****************************************************************************/ static int w5500_ifdown(FAR struct net_driver_s *dev) { FAR struct w5500_driver_s *self = (FAR struct w5500_driver_s *)dev->d_private; irqstate_t flags; /* Disable the Ethernet interrupt */ flags = enter_critical_section(); self->lower->enable(self->lower, false); /* Cancel the TX timeout timer */ wd_cancel(&self->w_txtimeout); /* Put the EMAC in its reset, non-operational state. This should be * a known configuration that will guarantee the w5500_ifup() always * successfully brings the interface back up. */ w5500_fence(self); /* Mark the device "down" */ self->w_bifup = false; leave_critical_section(flags); return OK; } /**************************************************************************** * Name: w5500_txavail_work * * Description: * Perform an out-of-cycle poll on the worker thread. * * Input Parameters: * arg - Reference to the NuttX driver state structure (cast to void*) * * Returned Value: * None * * Assumptions: * Runs on a work queue thread. * ****************************************************************************/ static void w5500_txavail_work(FAR void *arg) { FAR struct w5500_driver_s *priv = (FAR struct w5500_driver_s *)arg; /* Lock the network and serialize driver operations if necessary. * NOTE: Serialization is only required in the case where the driver work * is performed on an LP worker thread and where more than one LP worker * thread has been configured. */ net_lock(); /* Ignore the notification if the interface is not yet up */ if (priv->w_bifup) { /* Check if there is room in the hardware to hold another packet. */ /* If so, then poll the network for new XMIT data */ devif_poll(&priv->w_dev, w5500_txpoll); } net_unlock(); } /**************************************************************************** * Name: w5500_txavail * * Description: * Driver callback invoked when new TX data is available. This is a * stimulus perform an out-of-cycle poll and, thereby, reduce the TX * latency. * * Input Parameters: * dev - Reference to the NuttX driver state structure * * Returned Value: * None * * Assumptions: * The network is locked. * ****************************************************************************/ static int w5500_txavail(FAR struct net_driver_s *dev) { FAR struct w5500_driver_s *priv = (FAR struct w5500_driver_s *)dev->d_private; /* Is our single work structure available? It may not be if there are * pending interrupt actions and we will have to ignore the Tx * availability action. */ if (work_available(&priv->w_pollwork)) { /* Schedule to serialize the poll on the worker thread. */ work_queue(ETHWORK, &priv->w_pollwork, w5500_txavail_work, priv, 0); } return OK; } /**************************************************************************** * Name: w5500_addmac * * Description: * NuttX Callback: Add the specified MAC address to the hardware multicast * address filtering * * Input Parameters: * dev - Reference to the NuttX driver state structure * mac - The MAC address to be added * * Returned Value: * Zero (OK) on success; a negated errno value on failure. * ****************************************************************************/ #if defined(CONFIG_NET_MCASTGROUP) || defined(CONFIG_NET_ICMPv6) static int w5500_addmac(FAR struct net_driver_s *dev, FAR const uint8_t *mac) { FAR struct w5500_driver_s *priv = (FAR struct w5500_driver_s *)dev->d_private; /* Add the MAC address to the hardware multicast routing table */ return OK; } #endif /**************************************************************************** * Name: w5500_rmmac * * Description: * NuttX Callback: Remove the specified MAC address from the hardware * multicast address filtering * * Input Parameters: * dev - Reference to the NuttX driver state structure * mac - The MAC address to be removed * * Returned Value: * Zero (OK) on success; a negated errno value on failure. * ****************************************************************************/ #ifdef CONFIG_NET_MCASTGROUP static int w5500_rmmac(FAR struct net_driver_s *dev, FAR const uint8_t *mac) { FAR struct w5500_driver_s *priv = (FAR struct w5500_driver_s *)dev->d_private; /* Add the MAC address to the hardware multicast routing table */ return OK; } #endif /**************************************************************************** * Name: w5500_ipv6multicast * * Description: * Configure the IPv6 multicast MAC address. * * Input Parameters: * priv - A reference to the private driver state structure * * Returned Value: * Zero (OK) on success; a negated errno value on failure. * ****************************************************************************/ #ifdef CONFIG_NET_ICMPv6 static void w5500_ipv6multicast(FAR struct w5500_driver_s *priv) { FAR struct net_driver_s *dev; uint16_t tmp16; uint8_t mac[6]; /* For ICMPv6, we need to add the IPv6 multicast address * * For IPv6 multicast addresses, the Ethernet MAC is derived by * the four low-order octets OR'ed with the MAC 33:33:00:00:00:00, * so for example the IPv6 address FF02:DEAD:BEEF::1:3 would map * to the Ethernet MAC address 33:33:00:01:00:03. * * NOTES: This appears correct for the ICMPv6 Router Solicitation * Message, but the ICMPv6 Neighbor Solicitation message seems to * use 33:33:ff:01:00:03. */ mac[0] = 0x33; mac[1] = 0x33; dev = &priv->dev; tmp16 = dev->d_ipv6addr[6]; mac[2] = 0xff; mac[3] = tmp16 >> 8; tmp16 = dev->d_ipv6addr[7]; mac[4] = tmp16 & 0xff; mac[5] = tmp16 >> 8; ninfo("IPv6 Multicast: %02x:%02x:%02x:%02x:%02x:%02x\n", mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); w5500_addmac(dev, mac); #ifdef CONFIG_NET_ICMPv6_AUTOCONF /* Add the IPv6 all link-local nodes Ethernet address. This is the * address that we expect to receive ICMPv6 Router Advertisement * packets. */ w5500_addmac(dev, g_ipv6_ethallnodes.ether_addr_octet); #endif /* CONFIG_NET_ICMPv6_AUTOCONF */ #ifdef CONFIG_NET_ICMPv6_ROUTER /* Add the IPv6 all link-local routers Ethernet address. This is the * address that we expect to receive ICMPv6 Router Solicitation * packets. */ w5500_addmac(dev, g_ipv6_ethallrouters.ether_addr_octet); #endif /* CONFIG_NET_ICMPv6_ROUTER */ } #endif /* CONFIG_NET_ICMPv6 */ /**************************************************************************** * Name: w5500_ioctl * * Description: * Handle network IOCTL commands directed to this device. * * Input Parameters: * dev - Reference to the NuttX driver state structure * cmd - The IOCTL command * arg - The argument for the IOCTL command * * Returned Value: * OK on success; Negated errno on failure. * * Assumptions: * The network is locked. * ****************************************************************************/ #ifdef CONFIG_NETDEV_IOCTL static int w5500_ioctl(FAR struct net_driver_s *dev, int cmd, unsigned long arg) { FAR struct w5500_driver_s *priv = (FAR struct w5500_driver_s *)dev->d_private; /* Decode and dispatch the driver-specific IOCTL command */ switch (cmd) { /* Add cases here to support the IOCTL commands */ default: nerr("ERROR: Unrecognized IOCTL command: %d\n", cmd); return -ENOTTY; /* Special return value for this case */ } return OK; } #endif /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: w5500_initialize * * Description: * Initialize the Ethernet controller and driver * * Parameters: * spi - A reference to the platform's SPI driver for the W5500. * lower - The lower half driver instance for this W5500 chip. * devno - If more than one W5500 is supported, then this is the * zero based number that identifies the W5500. * * Returned Value: * OK on success; Negated errno on failure. * * Assumptions: * ****************************************************************************/ int w5500_initialize(FAR struct spi_dev_s *spi_dev, FAR const struct w5500_lower_s *lower, unsigned int devno) { FAR struct w5500_driver_s *self; /* Get the interface structure associated with this interface number. */ DEBUGASSERT(devno < CONFIG_NET_W5500_NINTERFACES); self = &g_w5500[devno]; /* Check if a Ethernet chip is recognized at its I/O base */ /* Attach the IRQ to the driver */ if (lower->attach(lower, w5500_interrupt, self)) { /* We could not attach the ISR to the interrupt */ return -EAGAIN; } /* Initialize the driver structure */ memset(self, 0, sizeof(struct w5500_driver_s)); self->w_dev.d_buf = (FAR uint8_t *)g_pktbuf[devno]; /* Single packet buffer */ self->w_dev.d_ifup = w5500_ifup; /* I/F up (new IP address) callback */ self->w_dev.d_ifdown = w5500_ifdown; /* I/F down callback */ self->w_dev.d_txavail = w5500_txavail; /* New TX data callback */ #ifdef CONFIG_NET_MCASTGROUP self->w_dev.d_addmac = w5500_addmac; /* Add multicast MAC address */ self->w_dev.d_rmmac = w5500_rmmac; /* Remove multicast MAC address */ #endif #ifdef CONFIG_NETDEV_IOCTL self->w_dev.d_ioctl = w5500_ioctl; /* Handle network IOCTL commands */ #endif self->w_dev.d_private = g_w5500; /* Used to recover private state from dev */ self->spi_dev = spi_dev; /* SPI hardware interconnect */ self->lower = lower; /* Low-level MCU specific support */ /* Put the interface in the down state. This usually amounts to resetting * the device and/or calling w5500_ifdown(). */ w5500_ifdown(&self->w_dev); /* Register the device with the OS so that socket IOCTLs can be performed */ netdev_register(&self->w_dev, NET_LL_ETHERNET); return OK; } #endif /* !defined(CONFIG_SCHED_WORKQUEUE) */ #endif /* CONFIG_NET_W5500 */