README ====== This README provides some information about the port of NuttX to the TI Hercules TMS570LS04x/03x LaunchPad Evaluation Kit (LAUNCHXL-TMS57004) featuring the Hercules TMS570LS0432PZ chip. Contents ======== - Toolchain - LEDs and Buttons - Serial Console - Debugging - Configurations Toolchain ========= All of these configurations are set up to build with Cygwin under Windows using the "GNU Tools for ARM Embedded Processors" that is maintained by ARM (unless stated otherwise in the description of the configuration). https://launchpad.net/gcc-arm-embedded That toolchain selection can easily be reconfigured using 'make menuconfig'. Here are the relevant current settings: Build Setup: CONFIG_HOST_WINDOWS=y : Window environment CONFIG_WINDOWS_CYGWIN=y : Cywin under Windows System Type -> Toolchain: CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIW=y : GNU ARM EABI toolchain LEDs and Buttons ================ LEDs ---- The launchpad has a four LEDs two power LEDs labeled D1 (red) that connects to the TMS570's NERROR pin and D7 (blue) that indicates the XDS200 POWER_EN signal, and two white, user LEDs labeled D12 that connects to the NHET08 pin and D11 that connects to GIOA2. NHET08 is one of 32 N2HET pins than can be available to the user if not used by N2HET. This implementation, however, uses only the single LED driven by GIOA2. That LED is tied to ground and illuminated with a high level output value. This LED is not used by the board port unless CONFIG_ARCH_LEDS is defined. In that case, the usage by the board port is defined in include/board.h and src/tms570_autoleds.c. The LED is used to encode OS-related events as follows: ------------------- ----------------------- ------ SYMBOL Meaning LED ------------------- ----------------------- ------ LED_STARTED NuttX has been started OFF LED_HEAPALLOCATE Heap has been allocated OFF LED_IRQSENABLED Interrupts enabled OFF LED_STACKCREATED Idle stack created ON LED_INIRQ In an interrupt N/C LED_SIGNAL In a signal handler N/C LED_ASSERTION An assertion failed N/C LED_PANIC The system has crashed FLASH Thus if the LED is statically on, NuttX has successfully booted and is, apparently, running normally. If the LED is flashing at approximately 2Hz, then a fatal error has been detected and the system has halted. Buttons ------- The launchpad has three mechanical buttons. Two of these are reset buttons: One button is labeled PORRST performs a power-on reset and one labeled RST performs an MCU reset. Only one button is available for general software usage. That button is labeled GIOA7 and is, obviously, sensed on GIOA7. GIOA7 is tied to ground, but will be pulled high if the GIOA7 button is depressed. Serial Console ============== This TMS570 has a single SCI. The SCI_RX and TX pins are connected to the FTDI chip which provides a virtual COM port for the launchpad. Configurations ============== Information Common to All Configurations ---------------------------------------- Each LaunchXL-TMS50704 configuration is maintained in a sub-directory and can be selected as follow: cd tools ./configure.sh launchxl-tms57004/ cd - . ./setenv.sh Before sourcing the setenv.sh file above, you should examine it and perform edits as necessary so that TOOLCHAIN_BIN is the correct path to the directory than holds your toolchain binaries. And then build NuttX by simply typing the following. At the conclusion of the make, the nuttx binary will reside in an ELF file called, simply, nuttx. make oldconfig make The that is provided above as an argument to the tools/configure.sh must be is one of the following. NOTES: 1. These configurations use the mconf-based configuration tool. To change any of these configurations using that tool, you should: a. Build and install the kconfig-mconf tool. See nuttx/README.txt see additional README.txt files in the NuttX tools repository. b. Execute 'make menuconfig' in nuttx/ in order to start the reconfiguration process. 2. All of these configurations are set up to build under Windows using the "GNU Tools for ARM Embedded Processors" that is maintained by ARM (unless stated otherwise in the description of the configuration). https://launchpad.net/gcc-arm-embedded That toolchain selection can easily be reconfigured using 'make menuconfig'. Here are the relevant current settings: Build Setup: CONFIG_HOST_WINDOWS=y : Window environment CONFIG_WINDOWS_CYGWIN=y : Cywin under Windows System Type -> Toolchain: CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIW=y : GNU ARM EABI toolchain Configuration sub-directories ----------------------------- nsh: Configures the NuttShell (nsh) located at examples/nsh.