/**************************************************************************** * drivers/sensors/ms58xx.c * Character driver for MEAS MS58XX Altimeters * * Copyright (C) 2015 Omni Hoverboards Inc. All rights reserved. * Author: Paul Alexander Patience * Updated by: Karim Keddam * * Copyright (C) 2016 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #if defined(CONFIG_I2C) && defined(CONFIG_SENSORS_MS58XX) /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ #ifndef CONFIG_MS58XX_I2C_FREQUENCY # define CONFIG_MS58XX_I2C_FREQUENCY 400000 #endif /* Register Definitions *****************************************************/ /* Register Addresses */ #define MS58XX_RESET_REG 0x1e /* Reset Register */ #define MS58XX_PRESS_REG 0x40 /* Pressure Register */ #define MS58XX_TEMP_REG 0x50 /* Temperature Register */ #define MS58XX_ADC_REG 0x00 /* ADC Register */ #define MS58XX_PROM_REG 0xa0 /* PROM Register */ /* PROM Definitions *********************************************************/ #define MS58XX_PROM_LEN 8 /**************************************************************************** * Private Types ****************************************************************************/ struct ms58xx_dev_s { FAR struct i2c_master_s *i2c; /* I2C interface */ uint8_t addr; /* I2C address */ enum ms58xx_model_e model; uint8_t crcindex; uint8_t crcshift; int32_t temp; /* Uncompensated temperature (degrees Centigrade) */ int32_t press; /* Uncompensated pressure (millibar) */ uint8_t osr; /* Oversampling ratio bits */ useconds_t delay; /* Oversampling ratio delay */ /* Calibration coefficients */ uint16_t c1; uint16_t c2; uint16_t c3; uint16_t c4; uint16_t c5; uint16_t c6; uint8_t c7; uint8_t c8; /* Constants used when calculating the temperature and the pressure */ uint8_t c1s; uint8_t c2s; uint8_t c3s; uint8_t c4s; uint8_t diffmull; uint8_t diffdivls; uint8_t offmull; uint8_t offdivls; uint8_t sensmull; uint8_t sensdivls; uint8_t offmulvl; uint8_t sensmulvl; uint8_t diffmulh; uint8_t diffdivhs; uint8_t offmulh; uint8_t offdivhs; uint8_t sensmulh; uint8_t sensdivhs; uint8_t pressdivs; }; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ /* CRC Calculation */ static uint8_t ms58xx_crc(FAR uint16_t *src, uint8_t crcndx, uint16_t crcmask); /* I2C Helpers */ static int ms58xx_i2c_write(FAR struct ms58xx_dev_s *priv, FAR const uint8_t *buffer, int buflen); static int ms58xx_i2c_read(FAR struct ms58xx_dev_s *priv, FAR uint8_t *buffer, int buflen); static int ms58xx_readu16(FAR struct ms58xx_dev_s *priv, uint8_t regaddr, FAR uint16_t *regval); static int ms58xx_readadc(FAR struct ms58xx_dev_s *priv, FAR uint32_t *adc); static int ms58xx_setosr(FAR struct ms58xx_dev_s *priv, uint16_t osr); static int ms58xx_reset(FAR struct ms58xx_dev_s *priv); static int ms58xx_readprom(FAR struct ms58xx_dev_s *priv); static int ms58xx_convert(FAR struct ms58xx_dev_s *priv, uint8_t regaddr, FAR uint32_t *regval); static int ms58xx_measure(FAR struct ms58xx_dev_s *priv); /* Character Driver Methods */ static int ms58xx_open(FAR struct file *filep); static int ms58xx_close(FAR struct file *filep); static ssize_t ms58xx_read(FAR struct file *filep, FAR char *buffer, size_t buflen); static ssize_t ms58xx_write(FAR struct file *filep, FAR const char *buffer, size_t buflen); static int ms58xx_ioctl(FAR struct file *filep, int cmd, unsigned long arg); /**************************************************************************** * Private Data ****************************************************************************/ static const struct file_operations g_fops = { ms58xx_open, ms58xx_close, ms58xx_read, ms58xx_write, NULL, ms58xx_ioctl #ifndef CONFIG_DISABLE_POLL , NULL #endif #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS , NULL #endif }; /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: ms58xx_crc * * Description: * Calculate the CRC. * ****************************************************************************/ static uint8_t ms58xx_crc(FAR uint16_t *src, uint8_t crcndx, uint16_t crcmask) { uint16_t cnt; uint16_t n_rem; uint16_t crc_read; uint8_t n_bit; n_rem = 0x00; crc_read = src[crcndx]; src[crcndx] &= ~crcmask; for (cnt = 0; cnt < 16; cnt++) { if (cnt % 2 == 1) { n_rem ^= (uint16_t)((src[cnt >> 1]) & 0x00ff); } else { n_rem ^= (uint16_t)(src[cnt >> 1] >> 8); } for (n_bit = 8; n_bit > 0; n_bit--) { if (n_rem & (0x8000)) { n_rem = (n_rem << 1) ^ 0x3000; } else { n_rem = (n_rem << 1); } } } n_rem = (0x000F & (n_rem >> 12)); src[crcndx] = crc_read; return (n_rem ^ 0x00); } /**************************************************************************** * Name: ms58xx_i2c_write * * Description: * Write to the I2C device. * ****************************************************************************/ static int ms58xx_i2c_write(FAR struct ms58xx_dev_s *priv, FAR const uint8_t *buffer, int buflen) { struct i2c_msg_s msg; int ret; /* Setup for the transfer */ msg.frequency = CONFIG_MS58XX_I2C_FREQUENCY, msg.addr = priv->addr; msg.flags = 0; msg.buffer = (FAR uint8_t *)buffer; /* Override const */ msg.length = buflen; /* Then perform the transfer. */ ret = I2C_TRANSFER(priv->i2c, &msg, 1); return (ret >= 0) ? OK : ret; } /**************************************************************************** * Name: ms58xx_i2c_read * * Description: * Read from the I2C device. * ****************************************************************************/ static int ms58xx_i2c_read(FAR struct ms58xx_dev_s *priv, FAR uint8_t *buffer, int buflen) { struct i2c_msg_s msg; int ret; /* Setup for the transfer */ msg.frequency = CONFIG_MS58XX_I2C_FREQUENCY, msg.addr = priv->addr, msg.flags = I2C_M_READ; msg.buffer = buffer; msg.length = buflen; /* Then perform the transfer. */ ret = I2C_TRANSFER(priv->i2c, &msg, 1); return (ret >= 0) ? OK : ret; } /**************************************************************************** * Name: ms58xx_readu16 * * Description: * Read from a 16-bit register. * ****************************************************************************/ static int ms58xx_readu16(FAR struct ms58xx_dev_s *priv, uint8_t regaddr, FAR uint16_t *regval) { uint8_t buffer[2]; int ret; sninfo("addr: %02x\n", regaddr); /* Write the register address */ ret = ms58xx_i2c_write(priv, ®addr, sizeof(regaddr)); if (ret < 0) { snerr("ERROR: i2c_write failed: %d\n", ret); return ret; } /* Restart and read 16 bits from the register */ ret = ms58xx_i2c_read(priv, buffer, sizeof(buffer)); if (ret < 0) { snerr("ERROR: i2c_read failed: %d\n", ret); return ret; } *regval = (uint16_t)buffer[0] << 8 | (uint16_t)buffer[1]; sninfo("value: %04x ret: %d\n", *regval, ret); return ret; } /**************************************************************************** * Name: ms58xx_readadc * * Description: * Read from the ADC register. * ****************************************************************************/ static int ms58xx_readadc(FAR struct ms58xx_dev_s *priv, FAR uint32_t *adc) { uint8_t regaddr; uint8_t buffer[3]; int ret; regaddr = MS58XX_ADC_REG; sninfo("addr: %02x\n", regaddr); /* Write the register address */ ret = ms58xx_i2c_write(priv, ®addr, sizeof(regaddr)); if (ret < 0) { snerr("ERROR: i2c_write failed: %d\n", ret); return ret; } /* Restart and read 24 bits from the register */ ret = ms58xx_i2c_read(priv, buffer, sizeof(buffer)); if (ret < 0) { snerr("ERROR: i2c_read failed: %d\n", ret); return ret; } *adc = (uint32_t)buffer[0] << 16 | (uint32_t)buffer[1] << 8 | (uint32_t)buffer[2]; sninfo("adc: %06x ret: %d\n", *adc, ret); return ret; } /**************************************************************************** * Name: ms58xx_setosr_1 * * Description: * Set the oversampling ratio. * ****************************************************************************/ static int ms58xx_setosr_1(FAR struct ms58xx_dev_s *priv, uint16_t osr) { int ret = OK; switch (osr) { case 256: priv->delay = 600; priv->osr = 0x0; break; case 512: priv->delay = 1170; priv->osr = 0x2; break; case 1024: priv->delay = 2280; priv->osr = 0x4; break; case 2048: priv->delay = 4540; priv->osr = 0x6; break; case 4096: priv->delay = 9040; priv->osr = 0x8; break; case 8192: priv->delay = 18080; priv->osr = 0xA; break; default: ret = -EINVAL; break; } return ret; } /**************************************************************************** * Name: ms58xx_setosr_2 * * Description: * Set the oversampling ratio. * ****************************************************************************/ static int ms58xx_setosr_2(FAR struct ms58xx_dev_s *priv, uint16_t osr) { int ret = OK; switch (osr) { case 256: priv->delay = 600; break; case 512: priv->delay = 1170; break; case 1024: priv->delay = 2280; break; case 2048: priv->delay = 4540; break; case 4096: priv->delay = 9040; break; default: ret = -EINVAL; break; } if (ret == OK) { priv->osr = (osr / 256 - 1) * 2; } return ret; } /**************************************************************************** * Name: ms58xx_setosr * * Description: * Set the oversampling ratio. * ****************************************************************************/ static int ms58xx_setosr(FAR struct ms58xx_dev_s *priv, uint16_t osr) { int ret = OK; sninfo("osr: %04x\n", osr); switch (priv->model) { case MS58XX_MODEL_MS5805_02: case MS58XX_MODEL_MS5837_30: ret = ms58xx_setosr_1(priv,osr); break; case MS58XX_MODEL_MS5803_02: case MS58XX_MODEL_MS5803_05: case MS58XX_MODEL_MS5803_07: case MS58XX_MODEL_MS5803_14: case MS58XX_MODEL_MS5803_30: case MS58XX_MODEL_MS5806_02: ret = ms58xx_setosr_2(priv,osr); break; default: ret = -EINVAL; break; } return ret; } /**************************************************************************** * Name: ms58xx_readprom * * Description: * Read from the PROM. * ****************************************************************************/ static int ms58xx_readprom(FAR struct ms58xx_dev_s *priv) { uint16_t prom[MS58XX_PROM_LEN]; uint8_t crc; uint8_t crcindex; uint8_t crcshift; uint16_t crcmask; int ret; int i; int len = MS58XX_PROM_LEN; switch (priv->model) { case MS58XX_MODEL_MS5805_02: case MS58XX_MODEL_MS5837_30: prom[MS58XX_PROM_LEN-1] = 0; len--; crcindex = 0; crcshift = 12; break; case MS58XX_MODEL_MS5803_02: case MS58XX_MODEL_MS5803_05: case MS58XX_MODEL_MS5803_07: case MS58XX_MODEL_MS5803_14: case MS58XX_MODEL_MS5803_30: case MS58XX_MODEL_MS5806_02: default: crcindex = 7; crcshift = 0; break; } /* We have to wait before the prom is ready is be read */ up_udelay(10000); for (i = 0; i < len; i++) { ret = ms58xx_readu16(priv, MS58XX_PROM_REG + i * 2, prom + i); if (ret < 0) { snerr("ERROR: ms58xx_readu16 failed: %d\n", ret); return ret; } } crcmask = (uint16_t)0xf << crcshift; crc = (uint8_t)((prom[crcindex] & crcmask) >> crcshift); if (crc != ms58xx_crc(prom, crcindex, crcmask)) { snerr("ERROR: crc mismatch\n"); return -ENODEV; } priv->c1 = prom[1]; priv->c2 = prom[2]; priv->c3 = prom[3]; priv->c4 = prom[4]; priv->c5 = prom[5]; priv->c6 = prom[6]; switch (priv->model) { case MS58XX_MODEL_MS5803_07: priv->c7 = (uint8_t)((prom[7] & 0x03f0) >> 4); priv->c8 = (uint8_t)((prom[7] & 0xf700) >> 10); break; case MS58XX_MODEL_MS5806_02: priv->c7 = (uint8_t)((prom[7] & 0x0ff0) >> 4); priv->c8 = 0; break; case MS58XX_MODEL_MS5803_02: case MS58XX_MODEL_MS5803_05: case MS58XX_MODEL_MS5803_14: case MS58XX_MODEL_MS5803_30: case MS58XX_MODEL_MS5805_02: case MS58XX_MODEL_MS5837_30: default: priv->c7 = 0; priv->c8 = 0; break; } return ret; } /**************************************************************************** * Name: ms58xx_reset * * Description: * Reset the device. * ****************************************************************************/ static int ms58xx_reset(FAR struct ms58xx_dev_s *priv) { uint8_t regaddr; int ret; regaddr = MS58XX_RESET_REG; sninfo("addr: %02x\n", regaddr); /* Write the register address */ ret = ms58xx_i2c_write(priv, ®addr, sizeof(regaddr)); if (ret < 0) { snerr("ERROR: i2c_write failed: %d\n", ret); return ret; } /* Check the CRC and read the calibration coefficients */ ret = ms58xx_readprom(priv); if (ret < 0) { snerr("ERROR: ms58xx_readprom failed: %d\n", ret); } return ret; } /**************************************************************************** * Name: ms58xx_convert * * Description: * Measure the uncompensated temperature or the uncompensated pressure. * ****************************************************************************/ static int ms58xx_convert(FAR struct ms58xx_dev_s *priv, uint8_t regaddr, FAR uint32_t *regval) { int ret; regaddr |= priv->osr; sninfo("addr: %02x\n", regaddr); /* Write the register address */ ret = ms58xx_i2c_write(priv, ®addr, sizeof(regaddr)); if (ret < 0) { snerr("ERROR: i2c_write failed: %d\n", ret); } /* Wait for the conversion to end */ up_udelay(priv->delay); /* Read the value from the ADC */ ret = ms58xx_readadc(priv, regval); if (ret < 0) { snerr("ERROR: ms58xx_readadc failed: %d\n", ret); return ret; } return ret; } /**************************************************************************** * Name: ms58xx_measure * * Description: * Measure the compensated temperature and the compensated pressure. * ****************************************************************************/ static int ms58xx_measure(FAR struct ms58xx_dev_s *priv) { uint32_t rawpress; uint32_t rawtemp; int32_t diff; int32_t temp; int64_t off; int64_t sens; int32_t press; int64_t diffmul; int64_t diffdiv; int64_t offmula; int64_t offdiva; int64_t sensmula; int64_t sensdiva; int64_t offmulb; int64_t sensmulb; int64_t tm; int64_t tp; int ret; ret = ms58xx_convert(priv, MS58XX_PRESS_REG, &rawpress); if (ret < 0) { snerr("ERROR: ms58xx_convert failed: %d\n", ret); return ret; } ret = ms58xx_convert(priv, MS58XX_TEMP_REG, &rawtemp); if (ret < 0) { snerr("ERROR: ms58xx_convert failed: %d\n", ret); return ret; } add_sensor_randomness(rawpress ^ rawtemp); diff = (int32_t)rawtemp - (int32_t)priv->c5 * ((int32_t)1 << 8); temp = (int32_t)((int64_t)2000 + (int64_t)diff * (int64_t)priv->c6 / ((int64_t)1 << 23)); off = (int64_t)priv->c2 * ((int64_t)1 << priv->c2s) + (int64_t)priv->c4 * (int64_t)diff / ((int64_t)1 << priv->c4s); sens = (int64_t)priv->c1 * ((int64_t)1 << priv->c1s) + (int64_t)priv->c3 * (int64_t)diff / ((int64_t)1 << priv->c3s); if (temp < 2000) { diffmul = (int64_t)priv->diffmull; diffdiv = (int64_t)1 << priv->diffdivls; offmula = (int64_t)priv->offmull; offdiva = (int64_t)1 << priv->offdivls; sensmula = (int64_t)priv->sensmull; sensdiva = (int64_t)1 << priv->sensdivls; if (temp < -1500) { offmulb = (int64_t)priv->offmulvl; sensmulb = (int64_t)priv->sensmulvl; } else { offmulb = 0; sensmulb = 0; } } else { diffmul = (int64_t)priv->diffmulh; diffdiv = (int64_t)1 << priv->diffdivhs; offmula = (int64_t)priv->offmulh; offdiva = (int64_t)1 << priv->offdivhs; sensmula = (int64_t)priv->sensmulh; sensdiva = (int64_t)1 << priv->sensdivhs; offmulb = 0; sensmulb = 0; } tm = (int64_t)temp - (int64_t)2000; tm *= tm; tp = (int64_t)temp + (int64_t)1500; tp *= tp; off -= offmula * tm / offdiva + offmulb * tp; sens -= sensmula * tm / sensdiva + sensmulb * tp; temp -= (int32_t)(diffmul * (int64_t)diff * (int64_t)diff / diffdiv); press = (int32_t)(((int64_t)rawpress * sens / ((int64_t)1 << 21) - off) / ((int64_t)1 << priv->pressdivs)); switch (priv->model) { case MS58XX_MODEL_MS5803_07: if (press > 110000) { press += (int32_t)((((int64_t)priv->c7 - ((int64_t)1 << 5)) * (int64_t)100 * ((int64_t)1 << 2) - ((int64_t)priv->c8 - ((int64_t)1 << 5)) * ((int64_t)temp - (int64_t)2000) / ((int64_t)1 << 4)) * ((int64_t)press - (int64_t)110000) / (int64_t)49000000); } break; case MS58XX_MODEL_MS5806_02: #if CONFIG_MS58XX_VDD >= 22 && CONFIG_MS58XX_VDD <= 30 press += (int32_t)(((int64_t)30 - (int64_t)CONFIG_MS58XX_VDD) * (int64_t)priv->c7 / (((int64_t)1 << 6) * (int64_t)10)); #endif break; case MS58XX_MODEL_MS5803_02: case MS58XX_MODEL_MS5803_05: case MS58XX_MODEL_MS5803_14: case MS58XX_MODEL_MS5803_30: case MS58XX_MODEL_MS5805_02: case MS58XX_MODEL_MS5837_30: break; } priv->temp = temp; priv->press = press; return ret; } /**************************************************************************** * Name: ms58xx_open * * Description: * This method is called when the device is opened. * ****************************************************************************/ static int ms58xx_open(FAR struct file *filep) { return OK; } /**************************************************************************** * Name: ms58xx_close * * Description: * This method is called when the device is closed. * ****************************************************************************/ static int ms58xx_close(FAR struct file *filep) { return OK; } /**************************************************************************** * Name: ms58xx_read * * Description: * A dummy read method. * ****************************************************************************/ static ssize_t ms58xx_read(FAR struct file *filep, FAR char *buffer, size_t buflen) { ssize_t size; FAR struct inode *inode = filep->f_inode; FAR struct ms58xx_dev_s *priv = inode->i_private; FAR struct ms58xx_measure_s *p = (FAR struct ms58xx_measure_s *)buffer; size = buflen; while (size >= sizeof(*p)) { if (ms58xx_measure(priv) < 0) { return -1; } p->temperature = priv->temp; p->pressure = priv->press; p++; size -= sizeof(*p); } return size; } /**************************************************************************** * Name: ms58xx_write * * Description: * A dummy write method. * ****************************************************************************/ static ssize_t ms58xx_write(FAR struct file *filep, FAR const char *buffer, size_t buflen) { return -ENOSYS; } /**************************************************************************** * Name: ms58xx_ioctl * * Description: * The standard ioctl method. * ****************************************************************************/ static int ms58xx_ioctl(FAR struct file *filep, int cmd, unsigned long arg) { FAR struct inode *inode = filep->f_inode; FAR struct ms58xx_dev_s *priv = inode->i_private; int ret = OK; /* Handle ioctl commands */ switch (cmd) { /* Measure the temperature and the pressure. Arg: None. */ case SNIOC_MEASURE: DEBUGASSERT(arg == 0); ret = ms58xx_measure(priv); break; /* Return the temperature last measured. Arg: int32_t* pointer. */ case SNIOC_TEMPERATURE: { FAR int32_t *ptr = (FAR int32_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = priv->temp; sninfo("temp: %08x\n", *ptr); } break; /* Return the pressure last measured. Arg: int32_t* pointer. */ case SNIOC_PRESSURE: { FAR int32_t *ptr = (FAR int32_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = priv->press; sninfo("press: %08x\n", *ptr); } break; /* Reset the device. Arg: None. */ case SNIOC_RESET: DEBUGASSERT(arg == 0); ret = ms58xx_reset(priv); break; /* Change the oversampling ratio. Arg: uint16_t value. */ case SNIOC_OVERSAMPLING: ret = ms58xx_setosr(priv, (uint16_t)arg); sninfo("osr: %04x ret: %d\n", *(uint16_t *)arg, ret); break; /* Unrecognized commands */ default: snerr("ERROR: Unrecognized cmd: %d arg: %ld\n", cmd, arg); ret = -ENOTTY; break; } return ret; } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: ms58xx_register * * Description: * Register the MS58XX character device as 'devpath'. * * Input Parameters: * devpath - The full path to the driver to register, e.g., "/dev/press0". * i2c - An I2C driver instance. * addr - The I2C address of the MS58XX. * osr - The oversampling ratio. * model - The MS58XX model. * * Returned Value: * Zero (OK) on success; a negated errno value on failure. * ****************************************************************************/ int ms58xx_register(FAR const char *devpath, FAR struct i2c_master_s *i2c, uint8_t addr, uint16_t osr, enum ms58xx_model_e model) { FAR struct ms58xx_dev_s *priv; int ret; /* Sanity check */ DEBUGASSERT(i2c != NULL); DEBUGASSERT(((model == MS58XX_MODEL_MS5803_02 || model == MS58XX_MODEL_MS5803_05 || model == MS58XX_MODEL_MS5803_07 || model == MS58XX_MODEL_MS5803_14 || model == MS58XX_MODEL_MS5803_30 || model == MS58XX_MODEL_MS5806_02) && (addr == MS58XX_ADDR0 || addr == MS58XX_ADDR1)) || ((model == MS58XX_MODEL_MS5805_02 || model == MS58XX_MODEL_MS5837_30) && addr == MS58XX_ADDR0)); /* Initialize the device's structure */ priv = (FAR struct ms58xx_dev_s *)kmm_malloc(sizeof(*priv)); if (priv == NULL) { snerr("ERROR: Failed to allocate instance\n"); return -ENOMEM; } priv->i2c = i2c; priv->addr = addr; priv->model = model; priv->temp = 0; priv->press = 0; switch (priv->model) { case MS58XX_MODEL_MS5803_02: case MS58XX_MODEL_MS5805_02: case MS58XX_MODEL_MS5806_02: default: priv->c1s = 16; priv->c2s = 17; priv->c3s = 7; priv->c4s = 6; break; case MS58XX_MODEL_MS5803_05: priv->c1s = 17; priv->c2s = 18; priv->c3s = 7; priv->c4s = 5; break; case MS58XX_MODEL_MS5803_07: priv->c1s = 17; priv->c2s = 18; priv->c3s = 6; priv->c4s = 5; break; case MS58XX_MODEL_MS5803_14: case MS58XX_MODEL_MS5803_30: case MS58XX_MODEL_MS5837_30: priv->c1s = 15; priv->c2s = 16; priv->c3s = 8; priv->c4s = 7; break; } switch (priv->model) { case MS58XX_MODEL_MS5803_02: case MS58XX_MODEL_MS5806_02: priv->diffmull = 1; priv->diffdivls = 31; priv->offmull = 61; priv->offdivls = 4; priv->sensmull = 2; priv->sensdivls = 0; priv->offmulvl = 20; priv->sensmulvl = 12; priv->diffmulh = 0; priv->diffdivhs = 0; priv->offmulh = 0; priv->offdivhs = 0; priv->sensmulh = 0; priv->sensdivhs = 0; break; case MS58XX_MODEL_MS5803_05: case MS58XX_MODEL_MS5803_07: priv->diffmull = 3; priv->diffdivls = 33; priv->offmull = 3; priv->offdivls = 3; priv->sensmull = 7; priv->sensdivls = 3; priv->offmulvl = 0; priv->sensmulvl = 3; priv->diffmulh = 0; priv->diffdivhs = 0; priv->offmulh = 0; priv->offdivhs = 0; priv->sensmulh = 0; priv->sensdivhs = 0; break; case MS58XX_MODEL_MS5803_14: case MS58XX_MODEL_MS5803_30: priv->diffmull = 3; priv->diffdivls = 33; priv->offmull = 3; priv->offdivls = 1; priv->sensmull = 5; priv->sensdivls = 3; priv->offmulvl = 7; priv->sensmulvl = 4; priv->diffmulh = 7; priv->diffdivhs = 37; priv->offmulh = 1; priv->offdivhs = 4; priv->sensmulh = 0; priv->sensdivhs = 0; break; case MS58XX_MODEL_MS5805_02: priv->diffmull = 11; priv->diffdivls = 35; priv->offmull = 31; priv->offdivls = 3; priv->sensmull = 63; priv->sensdivls = 5; priv->offmulvl = 0; priv->sensmulvl = 0; priv->diffmulh = 0; priv->diffdivhs = 0; priv->offmulh = 0; priv->offdivhs = 0; priv->sensmulh = 0; priv->sensdivhs = 0; break; case MS58XX_MODEL_MS5837_30: priv->diffmull = 3; priv->diffdivls = 33; priv->offmull = 3; priv->offdivls = 1; priv->sensmull = 5; priv->sensdivls = 3; priv->offmulvl = 7; priv->sensmulvl = 4; priv->diffmulh = 2; priv->diffdivhs = 37; priv->offmulh = 1; priv->offdivhs = 4; priv->sensmulh = 0; priv->sensdivhs = 0; break; } switch (priv->model) { case MS58XX_MODEL_MS5803_02: case MS58XX_MODEL_MS5803_05: case MS58XX_MODEL_MS5803_14: case MS58XX_MODEL_MS5805_02: case MS58XX_MODEL_MS5806_02: default: priv->pressdivs = 15; break; case MS58XX_MODEL_MS5803_30: case MS58XX_MODEL_MS5837_30: priv->pressdivs = 13; break; } ret = ms58xx_setosr(priv, osr); if (ret < 0) { snerr("ERROR: ms58xx_setosr failed: %d\n", ret); goto errout; } ret = ms58xx_reset(priv); if (ret < 0) { snerr("ERROR: ms58xx_reset failed: %d\n", ret); goto errout; } /* Register the character driver */ ret = register_driver(devpath, &g_fops, 0666, priv); if (ret < 0) { snerr("ERROR: Failed to register driver: %d\n", ret); goto errout; } return ret; errout: kmm_free(priv); return ret; } #endif /* CONFIG_I2C && CONFIG_SENSORS_MS58XX */