/**************************************************************************** * boards/arm/sam34/flipnclick-sam3x/include/board.h * * Copyright (C) 2018 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ #ifndef __BOARDS_ARM_SAM34_FLIPNCLICK_SAM3X_INCLUDE_BOARD_H #define __BOARDS_ARM_SAM34_FLIPNCLICK_SAM3X_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include # include # ifdef CONFIG_SAM34_GPIO_IRQ # include # endif #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Clocking *****************************************************************/ /* After power-on reset, the SAM3X device is running on a 4MHz internal RC. * These definitions will configure clocking * * MAINOSC: Frequency = 12MHz (crystal) * PLLA: PLL Divider = 1, Multiplier = 14 to generate PLLACK = 168MHz * Master Clock (MCK): Source = PLLACK, Prescalar = 1 to generate MCK = 84MHz * CPU clock: 84MHz */ #define BOARD_32KOSC_FREQUENCY (32768) #define BOARD_SCLK_FREQUENCY (BOARD_32KOSC_FREQUENCY) #define BOARD_MAINOSC_FREQUENCY (12000000) /* MAINOSC: 12MHz crystal on-board */ /* Main oscillator register settings. * * The start up time should be should be: * Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles. */ #define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */ /* PLLA configuration. * * Divider = 1 * Multiplier = 14 */ #define BOARD_CKGR_PLLAR_MUL (13 << PMC_CKGR_PLLAR_MUL_SHIFT) #define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT) #define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS /* PMC master clock register settings. * * Source = PLLA * Divider = 2 */ #define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA #define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV2 /* USB UTMI PLL start-up time */ #define BOARD_CKGR_UCKR_UPLLCOUNT (3 << PMC_CKGR_UCKR_UPLLCOUNT_SHIFT) /* Resulting frequencies */ #define BOARD_PLLA_FREQUENCY (168000000) /* PLLACK: 14 * 12Mhz / 1 */ #define BOARD_MCK_FREQUENCY (84000000) /* MCK: PLLACK / 2 */ #define BOARD_CPU_FREQUENCY (84000000) /* CPU: MCK */ /* HSMCI clocking * * Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK) * divided by (2*(CLKDIV+1)). * * MCI_SPEED = MCCK / (2*(CLKDIV+1)) * CLKDIV = MCCK / MCI_SPEED / 2 - 1 * * Where CLKDIV has a range of 0-255. */ /* MCK = 84MHz, CLKDIV = 104, MCI_SPEED = 84MHz / 2 * (104+1) = 400 KHz */ #define HSMCI_INIT_CLKDIV (104 << HSMCI_MR_CLKDIV_SHIFT) /* MCK = 84MHz, CLKDIV = 2, MCI_SPEED = 84MHz / 2 * (2+1) = 14 MHz */ #define HSMCI_MMCXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT) /* MCK = 84MHz, CLKDIV = 1, MCI_SPEED = 84MHz / 2 * (1+1) = 21 MHz */ #define HSMCI_SDXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT) #define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV /* FLASH wait states * * FWS MAX FREQUENCY * 1.62V 1.8V * --- ----- ------ * 0 17MHz 19MHz * 1 45MHz 50MHz * 2 58MHz 64MHz * 3 70MHz 80MHz * 4 78MHz 90MHz */ #define BOARD_FWS 4 /* LED definitions **********************************************************/ /* There are four LEDs on the top, blue side of the board. Only one can be * controlled by software: * * LED L - PB27 (PWM13) * * There are also four LEDs on the back, white side of the board: * * LED A - PC6 * LED B - PC5 * LED C - PC7 * LED D - PC8 * * A high output value illuminates the LEDs. */ #ifdef CONFIG_ARCH_LEDS /* LED index values for use with board_userled(): */ # define BOARD_LED_A 0 # define BOARD_LED_B 1 # define BOARD_LED_C 2 # define BOARD_LED_D 3 # define BOARD_NLEDS 4 /* LED bits for use with board_userled_all() */ # define BOARD_LED_A_BIT (1 << BOARD_LED_A) # define BOARD_LED_B_BIT (1 << BOARD_LED_B) # define BOARD_LED_C_BIT (1 << BOARD_LED_C) # define BOARD_LED_D_BIT (1 << BOARD_LED_D) #else /* LED index values for use with board_userled(): */ # define BOARD_LED_L 0 # define BOARD_LED_A 1 # define BOARD_LED_B 2 # define BOARD_LED_C 3 # define BOARD_LED_D 4 # define BOARD_NLEDS 5 /* LED bits for use with board_userled_all() */ # define BOARD_LED_L_BIT (1 << BOARD_LED_L) # define BOARD_LED_A_BIT (1 << BOARD_LED_A) # define BOARD_LED_B_BIT (1 << BOARD_LED_B) # define BOARD_LED_C_BIT (1 << BOARD_LED_C) # define BOARD_LED_D_BIT (1 << BOARD_LED_D) #endif /* These LEDs are available to the application and are all available to the * application unless CONFIG_ARCH_LEDS is defined. * In that case, the usage by the board port is defined in include/board.h * and src/sam_autoleds.c. * The LEDs are used to encode OS-related events as follows: * * SYMBOL MEANING LED STATE * L A B C D * ---------------- ----------------------- --- --- --- --- --- */ #define LED_STARTED 0 /* NuttX has been started OFF ON OFF OFF OFF */ #define LED_HEAPALLOCATE 1 /* Heap has been allocated OFF OFF ON OFF OFF */ #define LED_IRQSENABLED 2 /* Interrupts enabled OFF OFF OFF ON OFF */ #define LED_STACKCREATED 3 /* Idle stack created OFF OFF OFF OFF ON */ #define LED_INIRQ 4 /* In an interrupt GLO N/C N/C N/C N/C */ #define LED_SIGNAL 4 /* In a signal handler GLO N/C N/C N/C N/C */ #define LED_ASSERTION 4 /* An assertion failed GLO N/C N/C N/C N/C */ #define LED_PANIC 4 /* The system has crashed 2Hz N/C N/C N/C N/C */ #undef LED_IDLE /* MCU is is sleep mode ---- Not used ----- */ /* Thus if LED L is faintly glowing and all other LEDs are off * (except LED D which was left on but is no longer controlled by NuttX and * so may be in any state), * NuttX has successfully booted and is, apparently, running normally and * taking interrupts. * If any of LEDs A-D are statically set, then NuttX failed to boot and the * LED indicates the initialization phase where the failure occurred. * If LED L is flashing at approximately 2Hz, then a fatal error has been * detected and the system has halted. * * NOTE: After booting, LEDs A-D are no longer used by the system and may be * controlled the application. */ /* Button definitions *******************************************************/ /* There are no buttons on the Arduino Due board. */ /* GPIO pin configurations **************************************************/ /* Universal Asynchronous Receiver Transceiver (UART) * * The SAM3X has a UART and 4 USARTS. The Programming port uses a USB-to- * serial chip connected to the first of the MCU (RX0 and TX0 on PA8 and * PA9, respectively). * The output from that port is visible using the Arduino tool. * * Any of UART and USART0-3 may be used as a serial console. * By default, UART0 is used as the serial console in all configurations. * * There are no alternatives for these pins. */ /* Universal Synchronous Asynchronous Receiver Transmitter (USART) * * The RX and TX pins are available on the Arduino connector D0 and D1 * pins, respectively. * These are connected to USART0, RXD0 and TXD0 which are PA10 and PA11, * respectively. * * There are four Click bus connectors with serial ports available as * follows: * * Click A: USART0 RXD0 and TXD0 which are, again, PA10 and PA11. * Click B: USART1 RXD1 and TXD1 which are PA12 and PA13, respectively. * Click C: USART3 RXD3 and TXD3 which are PD5 and PD4, respectively. * Click D: USART3 RXD3 and TXD3 which are, again, PD5 and PD4. * * There are no alternatives for these pins. */ /* SPI: * * SPI0 is available on the Arduino compatible SPI connector (but no SPI is * available on pins D10-D13 of the main Arduino Shield connectors where * you might expect then). The SPI connector is configured as follows: * * Pin Board Signal SAM3X Pin Board Signal SAM3X * --- ------------ ----- --- ------------ ----- * 1 SPI0_MISO PA25 2 VCC-5V N/A * 3 SPI0_SCK PA27 4 SPI0_MOSI PA26 * 5 MRST NRSTB 6 GND N/A * * SPI0 is also available on each of the mikroBUS Click connectors (in * addition to 5V and GND). The connectivity differs only in the chip * select pin: * * MikroBUS A: MikroBUS B: * Pin Board Signal SAM3X Pin Board Signal SAM3X * ---- ------------ ----- ---- ------------ ----- * CS SPI0_CS0 PA28 CS PA29 PA29 * SCK SPI0_SCK PA27 SCK SPI0_SCK PA27 * MISO SPI0_MISO PA25 MISO SPI0_MISO PA25 * MOSI SPI0_MOSI PA26 MOSI SPI0_MOSI PA26 * * MikroBUS C: MikroBUS D: * Pin Board Signal SAM3X Pin Board Signal SAM3X * ---- ------------ ----- ---- ------------ ----- * CS SPI0_CS2 PB21 CS SPI0_CS3 PB23 * SCK SPI0_SCK PA27 SCK SPI0_SCK PA27 * MISO SPI0_MISO PA25 MISO SPI0_MISO PA25 * MOSI SPI0_MOSI PA26 MOSI SPI0_MOSI PA26 * * Chip select pin definitions are provided in * boards/arm/sam34/flipnclick-sam3x/src/flipnclick-3x.h. * * There are no alternative pin selections for SPI0_MISO and SPIO_MOSI. */ #define GPIO_SPI0_SPCK GPIO_SPI0_SPCK_1 /* I2C (aka TWI): * * I2C0 is available on pins D16-D17 of the Arduino Shield connectors where * you would expect then. The SPI connector is configured as follows: * * Pin Label J1 Board Signal SAM3X * --- ----- -- ------------ ----- * D16 SCL1 8 I2C0_SCL PA17 * D17 SDA1 7 I2C0_SDA PA18 * * I2C0 and I2C1 are also available on the mikroBUS Click connectors (in * addition to 5V and GND). The connectors A and B share I2C0 with the * Arduino shield connector. Connectors C and D both connect to I2C1: * * MikroBUS A: MikroBUS B: * Pin Board Signal SAM3X Pin Board Signal SAM3X * ---- ------------ ----- ---- ------------ ------- * SCL I2C0_SCL PA18 SCL I2C0_SCL PA18 * SDA I2C0_SDA PA17 SDA I2C0_SDA PA17 * * MikroBUS C: MikroBUS D: * Pin Board Signal SAM3X Pin Board Signal SAM3X * ---- ------------ ----- ---- ------------ ------- * SCL I2C1_SCL PB13 SCL I2C1_SCL PB13 * SDA I2C1_SDA PB12 SDA I2C1_SDA PB12 * * There are no alternative pin selections for TWI0 and TWI1. */ #endif /* __BOARDS_ARM_SAM34_FLIPNCLICK_SAM3X_INCLUDE_BOARD_H */