/**************************************************************************** * boards/arm/kinetis/kwikstik-k40/include/board.h * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ #ifndef __BOARDS_ARM_KINETIS_KWIKSTIK-K40_INCLUDE_BOARD_H #define __BOARDS_ARM_KINETIS_KWIKSTIK-K40_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Clocking *****************************************************************/ /* The Kwikstik-K40 has a 4MHz crystal on board */ #undef BOARD_EXTCLOCK /* Crystal */ #define BOARD_EXTAL_FREQ 4000000 /* 4MHz crystal frequency (REFCLK) */ #define BOARD_XTAL32_FREQ 32768 /* 32KHz RTC Oscillator */ /* PLL Configuration. NOTE: Only even frequency crystals are supported that * will produce a 2MHz reference clock to the PLL. * * PLL Input frequency: PLLIN = REFCLK/PRDIV = 4MHz/2 = 2MHz * PLL Output frequency: PLLOUT = PLLIN*VDIV = 2Mhz*48 = 96MHz * MCG Frequency: PLLOUT = 96MHz */ #define BOARD_PRDIV 2 /* PLL External Reference Divider */ #define BOARD_VDIV 48 /* PLL VCO Divider (frequency multiplier) */ #define BOARD_PLLIN_FREQ (BOARD_EXTAL_FREQ / BOARD_PRDIV) #define BOARD_PLLOUT_FREQ (BOARD_PLLIN_FREQ * BOARD_VDIV) #define BOARD_MCG_FREQ BOARD_PLLOUT_FREQ /* SIM CLKDIV1 dividers */ #define BOARD_OUTDIV1 1 /* Core = MCG, 96MHz */ #define BOARD_OUTDIV2 2 /* Bus = MCG/2, 48MHz */ #define BOARD_OUTDIV3 2 /* FlexBus = MCG/2, 48MHz */ #define BOARD_OUTDIV4 4 /* Flash clock = MCG/4, 24MHz */ #define BOARD_CORECLK_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV1) #define BOARD_BUS_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV2) #define BOARD_FLEXBUS_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV3) #define BOARD_FLASHCLK_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV4) /* SDHC clocking ************************************************************/ /* SDCLK configurations corresponding to various modes of operation. * Formula is: * * SDCLK frequency = (base clock) / (prescaler * divisor) * * The SDHC module is always configure configured so that the core clock is * the base clock. */ /* Identification mode: 400KHz = 96MHz / ( 16 * 15) */ #define BOARD_SDHC_IDMODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV16 #define BOARD_SDHC_IDMODE_DIVISOR SDHC_SYSCTL_DVS_DIV(15) /* MMC normal mode: 16MHz = 96MHz / (2 * 3) */ #define BOARD_SDHC_MMCMODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2 #define BOARD_SDHC_MMCMODE_DIVISOR SDHC_SYSCTL_DVS_DIV(3) /* SD normal mode (1-bit): 16MHz = 96MHz / (2 * 3) */ #define BOARD_SDHC_SD1MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2 #define BOARD_SDHC_SD1MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(3) /* SD normal mode (4-bit): 24MHz = 96MHz / (2 * 2) (with DMA) * SD normal mode (4-bit): 16MHz = 96MHz / (2 * 3) (no DMA) */ #ifdef CONFIG_SDIO_DMA # define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2 # define BOARD_SDHC_SD4MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(2) #else /* # define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2 */ /* # define BOARD_SDHC_SD4MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(3) */ # define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV16 # define BOARD_SDHC_SD4MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(15) #endif /* LED definitions **********************************************************/ /* The KwikStik-K40 board has no MCU driven, GPIO-based LEDs */ #define LED_STARTED 0 #define LED_HEAPALLOCATE 1 #define LED_IRQSENABLED 2 #define LED_STACKCREATED 3 #define LED_INIRQ 4 #define LED_SIGNAL 5 #define LED_ASSERTION 6 #define LED_PANIC 7 /* Button definitions *******************************************************/ /* The KwikStik-K40 board has no standard GPIO contact buttons */ /* Alternative pin resolution ***********************************************/ /* If there are alternative configurations for various pins in the * kinetis_k40pinmux.h header file, those alternative pins will be labeled * with a suffix like _1, _2, etc. * The logic in this file must select the correct pin configuration for the * board by defining a pin configuration (with no suffix) that maps to the * correct alternative. */ /* On-Board Connections * * ------------------- -------------------------- -------- ------------------ * FEATURE CONNECTION PORT/PIN PIN FUNCTION * ------------------- -------------------------- -------- ------------------ * Audio Jack Output Audio Amp On PTE28 PTE28 * Audio Output DAC1_OUT DAC1_OUT * Volume Up PTD10 PTD10 * Volume Down PTD11 PTD11 * Buzzer Audio Out PTA8 FTM1_CH0 * Microphone Microphone input PTA7 ADC0_SE10 * SD Card Slot SD Clock PTE2 SDHC0_DCLK * SD Command PTE3 SDHC0_CMD * SD Data0 PTD12 SDHC0_D4 * SD Data1 PTD13 SDHC0_D5 * SD Data2 PTD14 SDHC0_D6 * SD Data3 PTD15 SDHC0_D7 * SD Card Detect PTE27 PTE27 * SD Card On PTE6 PTE6 * Infrared Port IR Transmit PTE4 IR_TX * IR Receive PTA13 CMP2_IN0 * Touch Pads E1 / Touch PTB0 TSI0_CH0 * E2 / Touch PTA4 TSI0_CH5 * E3 / Touch PTA24 PTA24 * E4 / Touch PTA25 PTA25 * E5 / Touch PTA26 PTA26 * E6 / Touch PTA27 PTA27 */ #define PIN_FTM1_CH0 PIN_FTM1_CH0_1 /* Connections via the General Purpose Tower Plug-in (TWRPI) Socket * ------------------- -------------------------- -------- ------------------ * FEATURE CONNECTION PORT/PIN PIN FUNCTION * ------------------- -------------------------- -------- ------------------ * General Purpose TWRPI AN0 (J8 Pin 8) ? ADC0_DP0/ADC1_DP3 * TWRPI Socket TWRPI AN1 (J8 Pin 9) ? ADC0_DM0/ADC1_DM3 * TWRPI AN2 (J8 Pin 12) ? ADC1_DP0/ADC0_DP3 * TWRPI ID0 (J8 Pin 17) ? ADC0_DP1 * TWRPI ID1 (J8 Pin 18) ? ADC0_DM1 * TWRPI I2C SCL (J9 Pin 3) PTC10 I2C1_SCL * TWRPI I2C SDA (J9 Pin 4) PTC11 I2C1_SDA * TWRPI SPI MISO (J9 Pin 9) PTB23 SPI2_SIN * TWRPI SPI MOSI (J9 Pin 10) PTB22 SPI2_SOUT * TWRPI SPI SS (J9 Pin 11) PTB20 SPI2_PCS0 * TWRPI SPI CLK (J9 Pin 12) PTB21 SPI2_SCK * TWRPI GPIO0 (J9 Pin 15) PTC12 PTC12 * TWRPI GPIO1 (J9 Pin 16) PTB9 PTB9 * TWRPI GPIO2 (J9 Pin 17) PTB10 PTB10 * TWRPI GPIO3 (J9 Pin 18) PTC5 PTC5 * TWRPI GPIO4 (J9 Pin 19) PTA5 PTA5 */ #define PIN_I2C1_SCL PIN_I2C1_SCL_1 #define PIN_I2C1_SDA PIN_I2C1_SDA_1 #define PIN_SPI2_SIN PIN_SPI2_SIN_1 #define PIN_SPI2_SOUT PIN_SPI2_SOUT_1 #define PIN_SPI2_PCS0 PIN_SPI2_PCS0_1 #define PIN_SPI2_SCK PIN_SPI2_SCK_1 /* Connections via the Tower Primary Connector Side A * --- -------------------- -------------------------------- * PIN NAME USAGE * --- -------------------- -------------------------------- * A9 GPIO9 / CTS1 PTE10/UART_CTS * A43 RXD1 PTE9/UART_RX * A44 TXD1 PTE8/UART_TX * A63 RSTOUT_b PTA9/FTM1_CH1 */ #define PIN_UART5_CTS PIN_UART5_CTS_2 #define PIN_FTM1_CH1 PIN_FTM1_CH1_1 /* Connections via the Tower Primary Connector Side B * --- -------------------- -------------------------------- * PIN NAME USAGE * --- -------------------- -------------------------------- * B21 GPIO1 / RTS1 PTE7/UART_RTS * B37 PWM7 PTA8/FTM1_CH0 * B38 PWM6 PTA9/FTM1_CH1 * B41 CANRX0 PTE25/CAN1_RX * B42 CANTX0 PTE24/CAN1_TX * B44 SPI0_MISO PTA17/SPI0_SIN * B45 SPI0_MOSI PTA16/SPI0_SOUT * B46 SPI0_CS0_b PTA14/SPI0_PCS0 * B48 SPI0_CLK PTA15/SPI0_SCK * B50 SCL1 PTE1/I2C1_SCL * B51 SDA1 PTE0/I2C1_SDA * B52 GPIO5 / SD_CARD_DET PTA16 */ #define PIN_UART3_RTS PIN_UART3_RTS_3 #define PIN_CAN1_RX PIN_CAN1_RX_2 #define PIN_CAN1_TX PIN_CAN1_TX_2 #define PIN_SPI0_SIN PIN_SPI0_SIN_1 #define PIN_SPI0_SOUT PIN_SPI0_SOUT_1 #define PIN_SPI0_SCK PIN_SPI0_SCK_1 #define PIN_SPI0_PCS0 PIN_SPI0_PCS0_1 #define PIN_I2C1_SCL PIN_I2C1_SCL_2 #define PIN_I2C1_SDA PIN_I2C1_SDA_2 #endif /* __BOARDS_ARM_KINETIS_KWIKSTIK-K40_INCLUDE_BOARD_H */