/**************************************************************************** * boards/arm/stm32/mikroe-stm32f4/include/board.h * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ #ifndef __BOARDS_ARM_STM32_MIKROE_STM32F4_INCLUDE_BOARD_H #define __BOARDS_ARM_STM32_MIKROE_STM32F4_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Clocking *****************************************************************/ /* The Mikroe STM32F4 Mikromedia board features a single 32kHz crystal. * The main clock uses the internal 16Mhz RC oscillator. * * This is the canonical configuration: * System Clock source :PLL (HSE) * SYSCLK(Hz) :168000000 Determined by PLL configuration * HCLK(Hz) :168000000 (STM32_RCC_CFGR_HPRE) * AHB Prescaler :1 (STM32_RCC_CFGR_HPRE) * APB1 Prescaler :4 (STM32_RCC_CFGR_PPRE1) * APB2 Prescaler :2 (STM32_RCC_CFGR_PPRE2) * HSI Frequency(Hz) :16000000 (STM32_HSI_FREQUENCY) * PLLM :16 (STM32_PLLCFG_PLLM) * PLLN :36 (STM32_PLLCFG_PLLN) * PLLP :2 (STM32_PLLCFG_PLLP) * PLLQ :7 (STM32_PLLCFG_PLLQ) * Main regulator output voltage :Scale1 mode Needed for high speed SYSCLK * Flash Latency(WS) :5 * Prefetch Buffer :OFF * Instruction cache :ON * Data cache :ON * Require 48MHz for USB OTG FS, :Enabled * SDIO and RNG clock */ /* HSI - 16 MHz RC factory-trimmed * LSI - 32 KHz RC * HSE - On-board crystal frequency is 8MHz * LSE - 32.768 kHz */ #define STM32_BOARD_XTAL 8000000ul #define STM32_HSI_FREQUENCY 16000000ul #define STM32_LSI_FREQUENCY 32000 #define STM32_HSE_FREQUENCY STM32_BOARD_XTAL #define STM32_LSE_FREQUENCY 32768 /* Main PLL Configuration. * * PLL source is HSI * PLL_VCO = (STM32_HSI_FREQUENCY / PLLM) * PLLN * = (16,000,000 / 16) * 336 * = 336,000,000 * SYSCLK = PLL_VCO / PLLP * = 336,000,000 / 2 = 168,000,000 * USB OTG FS, SDIO and RNG Clock * = PLL_VCO / PLLQ * = 48,000,000 */ #define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(16) #define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336) #define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2 #define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7) #define STM32_SYSCLK_FREQUENCY 168000000ul /* AHB clock (HCLK) is SYSCLK (168MHz) */ #define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */ #define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY /* APB1 clock (PCLK1) is HCLK/4 (42MHz) */ #define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */ #define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4) /* Timers driven from APB1 will be twice PCLK1 */ #define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY) /* APB2 clock (PCLK2) is HCLK/2 (84MHz) */ #define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */ #define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2) /* Timers driven from APB2 will be twice PCLK2 */ #define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK2_FREQUENCY) /* Timer Frequencies, if APBx is set to 1, frequency is same to APBx * otherwise frequency is 2xAPBx. * Note: TIM1,8 are on APB2, others on APB1 */ #define BOARD_TIM1_FREQUENCY STM32_HCLK_FREQUENCY #define BOARD_TIM2_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM3_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM4_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM5_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM6_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM7_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM8_FREQUENCY STM32_HCLK_FREQUENCY /* LED definitions **********************************************************/ /* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in * any way. The following definitions are used to access individual LEDs. */ /* LED index values for use with board_userled() */ #if 0 #define BOARD_LED1 0 #define BOARD_LED2 1 #define BOARD_LED3 2 #define BOARD_LED4 3 #endif #define BOARD_NLEDS 0 #if 0 #define BOARD_LED_GREEN BOARD_LED1 #define BOARD_LED_ORANGE BOARD_LED2 #define BOARD_LED_RED BOARD_LED3 #define BOARD_LED_BLUE BOARD_LED4 /* LED bits for use with board_userled_all() */ #define BOARD_LED1_BIT (1 << BOARD_LED1) #define BOARD_LED2_BIT (1 << BOARD_LED2) #define BOARD_LED3_BIT (1 << BOARD_LED3) #define BOARD_LED4_BIT (1 << BOARD_LED4) /* If CONFIG_ARCH_LEDs is defined, * then NuttX will control the 4 LEDs on board the stm32f4discovery. * The following definitions describe how NuttX controls the LEDs: */ #define LED_STARTED 0 /* LED1 */ #define LED_HEAPALLOCATE 1 /* LED2 */ #define LED_IRQSENABLED 2 /* LED1 + LED2 */ #define LED_STACKCREATED 3 /* LED3 */ #define LED_INIRQ 4 /* LED1 + LED3 */ #define LED_SIGNAL 5 /* LED2 + LED3 */ #define LED_ASSERTION 6 /* LED1 + LED2 + LED3 */ #define LED_PANIC 7 /* N/C + N/C + N/C + LED4 */ /* Button definitions *******************************************************/ /* The STM32F4 Discovery supports one button: */ #define BUTTON_USER 0 #define NUM_BUTTONS 0 #define BUTTON_USER_BIT (1 << BUTTON_USER) #endif /* 0 */ /* Alternate function pin selections ****************************************/ /* UART2: * * The Mikroe-STM32F4 board has no on-board serial devices, but it brings out * UART2 to the expansion header. * (See the README.txt file for other options) */ #define GPIO_USART2_RX GPIO_USART2_RX_2 #define GPIO_USART2_TX GPIO_USART2_TX_2 /* PWM * * The STM32F4 Discovery has no real on-board PWM devices, but the board can * be configured to output a pulse train using TIM4 CH2 on PD13. */ #define GPIO_TIM4_CH2OUT GPIO_TIM4_CH2OUT_2 /* SPI - Onboard devices use SPI3, plus SPI2 routes to the I/O header */ #define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 #define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 #define GPIO_SPI2_SCK GPIO_SPI2_SCK_2 #define DMACHAN_SPI2_RX DMAMAP_SPI2_RX #define DMACHAN_SPI2_TX DMAMAP_SPI2_TX #define GPIO_SPI3_MISO GPIO_SPI3_MISO_2 #define GPIO_SPI3_MOSI GPIO_SPI3_MOSI_2 #define GPIO_SPI3_SCK GPIO_SPI3_SCK_2 #define DMACHAN_SPI3_RX DMAMAP_SPI3_RX_2 #define DMACHAN_SPI3_TX DMAMAP_SPI3_TX_2 /* Timer Inputs/Outputs (see the README.txt file for options) */ #define GPIO_TIM2_CH1IN GPIO_TIM2_CH1IN_2 #define GPIO_TIM2_CH2IN GPIO_TIM2_CH2IN_1 #define GPIO_TIM8_CH1IN GPIO_TIM8_CH1IN_1 #define GPIO_TIM8_CH2IN GPIO_TIM8_CH2IN_1 #endif /* __BOARDS_ARM_STM32_MIKROE_STM32F4_INCLUDE_BOARD_H */