/****************************************************************************
 * boards/xtensa/esp32s2/common/scripts/esp32s2_memory.ld
 * ESP32-S2 Linker Script Memory Layout
 *
 * This file describes the memory layout (memory blocks) as virtual
 * memory addresses.
 *
 * esp32s2_sections.ld contains output sections to link compiler output
 * into these memory blocks.
 *
 ****************************************************************************/

#include <nuttx/config.h>

#define RAM_IRAM_START    0x40020000
#define RAM_DRAM_START    0x3ffb0000

#define DATA_RAM_END      0x3ffe0000  /* 2nd stage bootloader iram_loader_seg
                                       * starts at SRAM block 14 (reclaimed
                                       * after app boots)
                                       */

#define IRAM_ORG    (RAM_IRAM_START + CONFIG_ESP32S2_INSTRUCTION_CACHE_SIZE \
                                    + CONFIG_ESP32S2_DATA_CACHE_SIZE)

#define DRAM_ORG    (RAM_DRAM_START + CONFIG_ESP32S2_INSTRUCTION_CACHE_SIZE \
                                    + CONFIG_ESP32S2_DATA_CACHE_SIZE)

#define I_D_RAM_SIZE   DATA_RAM_END - DRAM_ORG

#ifdef CONFIG_ESP32S2_FLASH_2M
#  define FLASH_SIZE        0x200000
#elif defined (CONFIG_ESP32S2_FLASH_4M)
#  define FLASH_SIZE        0x400000
#elif defined (CONFIG_ESP32S2_FLASH_8M)
#  define FLASH_SIZE        0x800000
#elif defined (CONFIG_ESP32S2_FLASH_16M)
#  define FLASH_SIZE        0x1000000
#endif

MEMORY
{
#ifdef CONFIG_ESP32S2_APP_FORMAT_MCUBOOT
  /* The origin values for "metadata" and "ROM" memory regions are the actual
   * load addresses.
   *
   * NOTE: The memory region starting from 0x0 with length represented by
   * CONFIG_ESP32S2_APP_MCUBOOT_HEADER_SIZE is reserved for the MCUboot header,
   * which will be prepended to the binary file by the "imgtool" during the
   * signing of firmware image.
   */

  metadata (RX) :        org = CONFIG_ESP32S2_APP_MCUBOOT_HEADER_SIZE, len = 0x20
  ROM (RX) :             org = CONFIG_ESP32S2_APP_MCUBOOT_HEADER_SIZE + 0x20,
                         len = FLASH_SIZE - (CONFIG_ESP32S2_APP_MCUBOOT_HEADER_SIZE + 0x20)
#endif

  /* Below values assume the flash cache is on, and have the blocks this
   * uses subtracted from the length of the various regions. The 'data access
   * port' dram/drom regions map to the same iram/irom regions but are
   * connected to the data port of the CPU and eg allow bytewise access.
   */

  /* IRAM for CPU */

  iram0_0_seg (RX) :                 org = IRAM_ORG, len = I_D_RAM_SIZE

  /* Flash mapped instruction data. */

#ifdef CONFIG_ESP32S2_APP_FORMAT_MCUBOOT
  irom0_0_seg (RX) :                 org = 0x40080020, len = FLASH_SIZE
#else
  /* The 0x20 offset is a convenience for the app binary image generation.
   * Flash cache has 64KB pages. The .bin file which is flashed to the chip
   * has a 0x18 byte file header, and each segment has a 0x08 byte segment
   * header. Setting this offset makes it simple to meet the flash cache MMU's
   * constraint that (paddr % 64KB == vaddr % 64KB).
   */

  irom0_0_seg (RX) :                 org = 0x40080020, len = FLASH_SIZE - 0x20
#endif

  /* Shared data RAM, excluding memory reserved for bootloader and ROM
   * bss/data/stack.
   */

  dram0_0_seg (RW) :                 org = DRAM_ORG, len = I_D_RAM_SIZE

  /* Flash mapped constant data */

#ifdef CONFIG_ESP32S2_APP_FORMAT_MCUBOOT
  /* The DROM segment origin is offset by 0x40 for mirroring the actual ROM
   * image layout:
   *    0x0  - 0x1F : MCUboot header
   *    0x20 - 0x3F : Application image metadata section
   *    0x40 onwards: ROM code and data
   * This is required to meet the following constraint from the external
   * flash MMU:
   *    VMA % 64KB == LMA % 64KB
   * i.e. the lower 16 bits of both the virtual address (address seen by the
   * CPU) and the load address (physical address of the external flash) must
   * be equal.
   */

  drom0_0_seg (R) :      org = 0x3f000000 + (CONFIG_ESP32S2_APP_MCUBOOT_HEADER_SIZE + 0x20),
                         len = FLASH_SIZE - (CONFIG_ESP32S2_APP_MCUBOOT_HEADER_SIZE + 0x20)
#else
  /* The 0x20 offset is a convenience for the app binary image generation.
   * Flash cache has 64KB pages. The .bin file which is flashed to the chip
   * has a 0x18 byte file header, and each segment has a 0x08 byte segment
   * header. Setting this offset makes it simple to meet the flash cache MMU's
   * constraint that (paddr % 64KB == vaddr % 64KB).
   */

  drom0_0_seg (R) :                  org = 0x3f000020, len = FLASH_SIZE - 0x20
#endif

  /* RTC fast memory (executable). Persists over deep sleep. */

  rtc_iram_seg(RWX) :                org = 0x40070000, len = 0x2000

  /* RTC slow memory (data accessible). Persists over deep sleep.
   * Start of RTC slow memory is reserved for ULP co-processor code + data,
   * if enabled.
   */

  rtc_slow_seg(RW)  :    org = 0x50000000 + CONFIG_ESP32S2_ULP_COPROC_RESERVE_MEM,
                         len = 0x2000 - CONFIG_ESP32S2_ULP_COPROC_RESERVE_MEM

  /* RTC fast memory (same block as above), viewed from data bus */
  rtc_data_seg(RW)  :                 org = 0x3ff9e000, len = 0x2000
}

#if CONFIG_ESP32S2_RUN_IRAM
  REGION_ALIAS("default_rodata_seg", dram0_0_seg);
  REGION_ALIAS("default_code_seg", iram0_0_seg);
#else
  REGION_ALIAS("default_rodata_seg", drom0_0_seg);
  REGION_ALIAS("default_code_seg", irom0_0_seg);
#endif /* CONFIG_ESP32S2_RUN_IRAM */