/************************************************************************************
* configs/sama5d3x-ek/include/board_528mhz.h
*
* Copyright (C) 2014 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_528MHZ_H
#define __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_528MHZ_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* After power-on reset, the SAMA5 device is running on a 12MHz internal RC. These
* definitions will configure operational clocking.
*
* This is the configuration results in a CPU clock of 528MHz:
*
* MAINOSC: Frequency = 12MHz (crystal)
* PLLA: PLL Divider = 1, Multiplier = 43+1 to generate PLLACK = 528MHz
* Master Clock (MCK): Source = PLLACK/1, Prescalar = 1, MDIV = 4 to generate
* MCK = 132MHz
* CPU clock = 528MHz
*/
/* Main oscillator register settings.
*
* The start up time should be should be:
* Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles.
*/
#define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */
/* PLLA configuration.
*
* Divider = 1
* Multipler = 43+1
*/
#define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT)
#define BOARD_CKGR_PLLAR_OUT (0)
#define BOARD_CKGR_PLLAR_MUL (43 << PMC_CKGR_PLLAR_MUL_SHIFT)
#define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS
/* PMC master clock register settings.
*
* Master/Processor Clock Source Selection = PLLA
* Master/Processor Clock Prescaler = 1
* PLLA Divider = 1
* Master Clock Division (MDIV) = 4
*
* NOTE: Bit PLLADIV2 must always be set to 1 when MDIV is set to 3.
*
* Prescaler input = 528MHz / 1 = 528MHz
* Prescaler output = 528MHz / 1 = 528MHz
* Processor Clock (PCK) = 528MHz
* Master clock (MCK) = 528MHz / 4 = 132MHz
*/
#define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA
#define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV1
#define BOARD_PMC_MCKR_PLLADIV PMC_MCKR_PLLADIV1
#define BOARD_PMC_MCKR_MDIV PMC_MCKR_MDIV_PCKDIV4
/* ADC Configuration
*
* ADCClock = MCK / ((PRESCAL+1) * 2)
*
* Given:
* MCK = 132MHz
* ADCClock = 8MHz
* Then:
* PRESCAL = 7.25
*
* PRESCAL=7 and MCK=132MHz yields ADC clock of 8.25MHz
*/
#define BOARD_ADC_PRESCAL (7)
#define BOARD_TSD_STARTUP (40) /* 40 nanoseconds */
#define BOARD_TSD_TRACKTIM (2000) /* Min 1�s at 8MHz */
#define BOARD_TSD_DEBOUNCE (10000000) /* 10 milliseconds (units nanoseconds) */
/* Resulting frequencies */
#define BOARD_MAINCK_FREQUENCY BOARD_MAINOSC_FREQUENCY
#define BOARD_PLLA_FREQUENCY (528000000) /* PLLACK: 44 * 12Mhz / 1 */
#define BOARD_PCK_FREQUENCY (528000000) /* CPU: PLLACK / 1 / 1 */
#define BOARD_MCK_FREQUENCY (132000000) /* MCK: PLLACK / 1 / 1 / 4 */
#define BOARD_ADCCLK_FREQUENCY (8250000) /* ADCCLK: MCK / ((7+1)*2) */
/* On some SAMA5's, the clocking to peripherals may be divided down from MCK,
* but not for the SAMA5D3.
*/
#define BOARD_PIT_FREQUENCY BOARD_MCK_FREQUENCY
#define BOARD_USART_FREQUENCY BOARD_MCK_FREQUENCY
#if defined(CONFIG_SAMA5_EHCI) || defined(CONFIG_SAMA5_OHCI) || \
defined(CONFIG_SAMA5_UDPHS)
/* The USB Host High Speed requires a 480 MHz clock (UPLLCK) for the embedded
* High-speed transceivers. UPLLCK is the output of the 480 MHz UTMI PLL
* (UPLL). The source clock of the UTMI PLL is the Main OSC output: Either
* the 12MHz internal RC oscillator on a an external 12MHz crystal. The
* Main OSC must be 12MHz because the UPLL has a built-in 40x multiplier.
*
* For High-speed operations, the user has to perform the following:
*
* 1) Enable UHP peripheral clock, bit (1 << AT91C_ID_UHPHS) in
* PMC_PCER register.
* 2) Write CKGR_PLLCOUNT field in PMC_UCKR register.
* 3) Enable UPLL, bit AT91C_CKGR_UPLLEN in PMC_UCKR register.
* 4) Wait until UTMI_PLL is locked. LOCKU bit in PMC_SR register
* 5) Enable BIAS, bit AT91C_CKGR_BIASEN in PMC_UCKR register.
* 6) Select UPLLCK as Input clock of OHCI part, USBS bit in PMC_USB
* register.
* 7) Program the OHCI clocks (UHP48M and UHP12M) with USBDIV field in
* PMC_USB register. USBDIV must be 9 (division by 10) if UPLLCK is
* selected.
* 8) Enable OHCI clocks, UHP bit in PMC_SCER register.
*
* Steps 2 through 7 performed here. 1 and 8 are performed in the EHCI
* driver is initialized.
*/
# define BOARD_USE_UPLL 1 /* Use UPLL for clock source */
# define BOARD_CKGR_UCKR_UPLLCOUNT (15) /* Maximum value */
# define BOARD_CKGR_UCKR_BIASCOUNT (15) /* Maximum value */
/* REVISIT: The divisor of 10 produces a rate that is too high. Division
* by 5, however, seems to work just fine. No idea why?
*/
# define BOARD_UPLL_OHCI_DIV (5) /* Divide by 5 */
#endif
/* HSMCI clocking
*
* Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK)
* divided by (2*(CLKDIV) + CLOCKODD + 2).
*
* MCI_SPEED = MCK / (2*CLKDIV + CLOCKODD + 2)
*
* Where CLKDIV has a range of 0-255.
*/
/* MCK = 132MHz, CLKDIV = 164, MCI_SPEED = 132MHz / (2*164 + 0 + 2) = 400 KHz */
#define HSMCI_INIT_CLKDIV (164 << HSMCI_MR_CLKDIV_SHIFT)
/* MCK = 132MHz, CLKDIV = 2 w/CLOCKODD, MCI_SPEED = 132MHz /(2*2 + 1 + 2) = 18.9 MHz */
#define HSMCI_MMCXFR_CLKDIV ((2 << HSMCI_MR_CLKDIV_SHIFT) | HSMCI_MR_CLKODD)
/* MCK = 132MHz, CLKDIV = 2, MCI_SPEED = 132MHz /(2*2 + 0 + 2) = 22 MHz */
#define HSMCI_SDXFR_CLKDIV (2 << HSMCI_MR_CLKDIV_SHIFT)
#define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* !__ASSEMBLY__ */
#endif /* __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_528MHZ_H */