/************************************************************************************ * configs/stm32l476-mdk/include/board.h * * Copyright (C) 2016 Gregory Nutt. All rights reserved. * Copyright (C) 2016 Motorola Mobility, LLC. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ************************************************************************************/ #ifndef __CONFIGS_STM32L476_MDK_INCLUDE_BOARD_H #define __CONFIGS_STM32L476_MDK_INCLUDE_BOARD_H /************************************************************************************ * Included Files ************************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif /************************************************************************************ * Pre-processor Definitions ************************************************************************************/ /* Clocking *************************************************************************/ #include /* DMA Channel/Stream Selections ****************************************************/ /* Stream selections are arbitrary for now but might become important in the future * is we set aside more DMA channels/streams. */ /* Alternate function pin selections ************************************************/ /* USART1: * RXD: PB7 * TXD: PA6 * * these pins are shared with the I2C1, which is used for some onboard * devices, so I am disabling USART1, however I'm leaving the declarations * here for documentation for anyone who might want to use it instead of * those onboard devices. */ /* USART */ #define GPIO_USART1_CTS GPIO_USART1_CTS_3 /* PG11 */ #define GPIO_USART1_RTS GPIO_USART1_RTS_DE_2 /* PB3 */ #define GPIO_USART1_RX GPIO_USART1_RX_2 /* PB7 */ #define GPIO_USART1_TX GPIO_USART1_TX_2 /* PB6 */ #define GPIO_USART2_CTS GPIO_USART2_CTS_1 /* PA0 */ #define GPIO_USART2_RTS GPIO_USART2_RTS_DE_1 /* PA1 */ #define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */ #define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */ #define GPIO_USART3_RX GPIO_USART3_RX_3 /* PC11 */ #define GPIO_USART3_TX GPIO_USART3_TX_3 /* PC10 */ /* I2C */ #define GPIO_I2C2_SCL GPIO_I2C2_SCL_1 /* PB10 */ #define GPIO_I2C2_SDA GPIO_I2C2_SDA_1 /* PB11 */ #define GPIO_I2C3_SCL GPIO_I2C3_SCL_1 /* PC0 */ #define GPIO_I2C3_SDA GPIO_I2C3_SDA_1 /* PC1 */ /* SPI */ #define GPIO_SPI1_MISO GPIO_SPI1_MISO_1 /* PA6 */ #define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1 /* PA7 */ #define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 /* PA5 */ #define GPIO_SPI1_NSS GPIO_SPI1_NSS_1 /* PA4 */ #define DMACHAN_SPI1_RX DMACHAN_SPI1_RX_1 #define DMACHAN_SPI1_TX DMACHAN_SPI1_TX_1 #define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 /* PB14 */ #define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 /* PB15 */ #define GPIO_SPI2_SCK GPIO_SPI2_SCK_2 /* PB13 */ #define GPIO_SPI2_NSS GPIO_SPI2_NSS_2 /* PB12 */ /* LED definitions ******************************************************************/ /* The Reference Moto Mod contains three LEDs. Two LEDs, are by convention, used to * indicate the Reference Moto Mod battery state of charge, and the other is * available for you to use in your applications. * * 1. The red LED on PD7. Part of the (rear-firing) red/green LED. * 2. The green LED on PE7. Part of the (rear-firing) red/green LED. * 3. The white (top-firing) LED on PE8 * * When the I/O is HIGH value, the LED is OFF. * When the I/O is LOW, the LED is ON. * * Following this convention, only the white LED is made available even though they * all could be user-application controlled if desired. */ /* LED index values for use with board_userled() */ #define BOARD_RED_LED 0 #define BOARD_GREEN_LED 1 #ifndef CONFIG_ARCH_LEDS # define BOARD_WHITE_LED 2 # define BOARD_NLEDS 3 #else # define BOARD_NLEDS 2 #endif /* LED bits for use with board_userled_all() */ #define BOARD_RED_LED_BIT (1 << BOARD_RED_LED) #define BOARD_GREEN_LED_BIT (1 << BOARD_GREEN_LED) #ifndef CONFIG_ARCH_LEDS # define BOARD_WHITE_LED_BIT (1 << BOARD_WHITE_LED) #endif /* None of the LEDs are used by the board port unless CONFIG_ARCH_LEDS is defined. * In that case, the white LED (only) will be controlled. Usage by the board port * is defined in include/board.h and src/stm32_autoleds.c. The white LED will be * used to encode OS-related events as follows: * * ------------------- ---------------------------- ------ * SYMBOL Meaning LED * ------------------- ---------------------------- ------ */ #define LED_STARTED 0 /* NuttX has been started OFF */ #define LED_HEAPALLOCATE 0 /* Heap has been allocated OFF */ #define LED_IRQSENABLED 0 /* Interrupts enabled OFF */ #define LED_STACKCREATED 1 /* Idle stack created ON */ #define LED_INIRQ 2 /* In an interrupt N/C */ #define LED_SIGNAL 2 /* In a signal handler N/C */ #define LED_ASSERTION 2 /* An assertion failed N/C */ #define LED_PANIC 3 /* The system has crashed FLASH */ #undef LED_IDLE /* MCU is is sleep mode Not used */ /* Thus if the white LED is statically on, NuttX has successfully booted and is, * apparently, running normally. If white LED is flashing at approximately 2Hz, * then a fatal error has been detected and the system has halted. */ /* Buttons **************************************************************************/ /* The board only has one button */ #define BUTTON_POWER 0 #define NUM_BUTTONS 1 #define BUTTON_POWER_BIT (1 << BUTTON_POWER) /************************************************************************************ * Public Data ************************************************************************************/ #ifndef __ASSEMBLY__ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /************************************************************************************ * Public Function Prototypes ************************************************************************************/ /************************************************************************************ * Name: stm32l4_board_initialize * * Description: * All STM32L4 architectures must provide the following entry point. This entry * point is called early in the initialization -- after all memory has been * configured and mapped but before any devices have been initialized. * ************************************************************************************/ void stm32l4_board_initialize(void); #undef EXTERN #if defined(__cplusplus) } #endif #endif /* __ASSEMBLY__ */ #endif /* __CONFIGS_STM32L476_MDK_INCLUDE_BOARD_H */