/************************************************************************************ * configs/avr32dev1/include/board.h * include/arch/board/board.h * * Copyright (C) 2010 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ************************************************************************************/ #ifndef __ARCH_BOARD_BOARD_H #define __ARCH_BOARD_BOARD_H /************************************************************************************ * Included Files ************************************************************************************/ #include #include #include /************************************************************************************ * Definitions ************************************************************************************/ /* Clocking *************************************************************************/ /* Oscillator setup: RCOSC, OSC32, OSC0, OSC1. Only RCOSC, OSC0, or PLL0 can drive * the main clock. */ /* #define AVR32_FRCOSC 15200 RCOSC frequency in Hz */ #define AVR32_FOSC32 32768 /* OSC32 frequency in Hz */ #define AVR32_OSC32STARTUP 3 /* OSC32 startup time in RCOSC periods */ #define AVR32_FOSC0 12000000 /* OSC0 frequency in Hz */ #define AVR32_OSC0STARTUP 3 /* OSC0 startup time in RCOSC periods. /* #define AVR32_FOSC1 12000000 OSC1 frequency: Hz. * #define AVR32_OSC1STARTUP 3 OSC1 startup time in RCOSC periods. */ /* PLL setup * * FOSC0 MUL DIV PLL DIV2_EN CPU_CLOCK PBA_CLOCK COMMENT * (MHz) (MHz) (MHz) (MHz) * 12 15 1 192 1 12 12 * 12 9 3 40 1 20 20 PLL out of spec * 12 15 1 192 1 24 12 * 12 9 1 120 1 30 15 * 12 9 3 40 0 40 20 PLL out of spec * 12 15 1 192 1 48 12 * 12 15 1 192 1 48 24 * 12 8 1 108 1 54 27 * 12 9 1 120 1 60 15 * 12 9 1 120 1 60 30 * 12 10 1 132 1 66 16.5 */ #define AVR32_CLOCK_PLL0_OSC0 1 #undef AVR32_CLOCK_PLL0_OSC1 #define AVR32_PLL0_MUL 15 #define AVR32_PLL0_DIV 1 #define AVR32_PLL0_DIV2 1 #define AVR32_PLL0_WBWM 0 #define AVR32_PLL0_FREQ 192000000 /* Set PLL1 @ 96 MHz from OSC0: 12MHz*(7+1)/1 = 96MHz */ #define AVR32_CLOCK_PLL1_OSC0 1 #undef AVR32_CLOCK_PLL1_OSC1 #define AVR32_PLL1_MUL 7 #define AVR32_PLL1_DIV 1 #define AVR32_PLL1_DIV2 1 #define AVR32_PLL1_WBWM 0 #define AVR32_PLL1_FREQ 96000000 /* Clock divider setup */ #define AVR32_CKSEL_CPUDIV 0 #define AVR32_CKSEL_HSBDIV 0 #define AVR32_CKSEL_PBADIV 0 #define AVR32_CKSEL_PBBDIV 0 /* GCLK_USBB */ #undef AVR32_CLOCK_USB_PLL0 #define AVR32_CLOCK_USB_PLL1 1 #undef AVR32_CLOCK_USB_OSC0 #undef AVR32_CLOCK_USB_OSC1 #define AVR32_CLOCK_USB_DIV 0 /* Main Clock settup: Select OSC0 as the main clock */ #define AVR32_CLOCK_OSC0 1 #undef AVR32_CLOCK_OSC1 #undef AVR32_CLOCK_PLL0 #undef AVR32_CLOCK_PLL1 #define AVR32_CPU_CLOCK AVR32_FOSC0 #define AVR32_PBA_CLOCK AVR32_FOSC0 /* Pin muliplexing selecion *********************************************************/ #define PINMUX_USART1_RXD PINMUX_USART1_RXD_1 #define PINMUX_USART1_TXD PINMUX_USART1_TXD_1 /* LED definitions ******************************************************************/ /* The AVR32DEV1 board has 3 LEDs, two of which can be controlled through GPIO pins */ /* ON OFF */ /* LED1 LED2 LED1 LED2 */ #define LED_STARTED 0 /* OFF OFF OFF OFF */ #define LED_HEAPALLOCATE 0 /* OFF OFF OFF OFF */ #define LED_IRQSENABLED 0 /* OFF OFF OFF OFF */ #define LED_STACKCREATED 1 /* ON OFF OFF OFF */ #define LED_INIRQ 2 /* ON ON ON OFF */ #define LED_SIGNAL 2 /* ON ON ON OFF */ #define LED_ASSERTION 2 /* ON ON ON OFF */ #define LED_PANIC 2 /* ON ON ON OFF */ /* Button definitions ***************************************************************/ /* The AVR32DEV1 board has 3 BUTTONs, two of which can be sensed through GPIO pins. */ #define BUTTON1 1 /* Bit 0: Button 1 */ #define BUTTON2 2 /* Bit 1: Button 2 */ /************************************************************************************ * Public Types ************************************************************************************/ #ifndef __ASSEMBLY__ /************************************************************************************ * Public Data ************************************************************************************/ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /************************************************************************************ * Public Function Prototypes ************************************************************************************/ /************************************************************************************ * Name: avr32_boardinitialize * * Description: * All AVR32 architectures must provide the following entry point. This entry point * is called early in the intitialization -- after all memory has been configured * and mapped but before any devices have been initialized. * ************************************************************************************/ EXTERN void avr32_boardinitialize(void); /************************************************************************************ * Name: up_buttoninit * * Description: * up_buttoninit() must be called to initialize button resources. After that, * up_buttons() may be called to collect the state of all buttons. up_buttons() * returns an 8-bit bit set with each bit associated with a button. See the * BUTTON* definitions above for the meaning of each bit in the returned value. * * NOTE: Nothing in the "base" NuttX code calls up_buttoninit(). If you want button * support in an application, your application startup code must call up_buttoninit() * prior to calling any of the other button interfaces. * ************************************************************************************/ #ifdef CONFIG_ARCH_BUTTONS EXTERN void up_buttoninit(void); /************************************************************************************ * Name: up_buttons * * Description: * After up_buttoninit() has been called, up_buttons() may be called to collect * the state of all buttons. up_buttons() returns an 8-bit bit set with each bit * associated with a button. See the BUTTON* definitions above for the meaning of * each bit in the returned value. * ************************************************************************************/ EXTERN uint8_t up_buttons(void); /************************************************************************************ * Name: up_irqbutton1/2 * * Description: * These functions may be called to register an interrupt handler that will be * called when BUTTON1/2 is depressed. The previous interrupt handler value is * returned (so that it may restored, if so desired). * * Configuration Notes: * Configuration CONFIG_AVR32_GPIOIRQ must be selected to enable the overall GPIO * IRQ feature and CONFIG_AVR32_GPIOIRQSETA and/or CONFIG_AVR32_GPIOIRQSETB must * be enabled to select GPIOs to support interrupts on. For button support, bits * 2 and 3 must be set in CONFIG_AVR32_GPIOIRQSETB (PB2 and PB3). * ************************************************************************************/ #ifdef CONFIG_AVR32_GPIOIRQ EXTERN xcpt_t up_irqbutton1(xcpt_t irqhandler); EXTERN xcpt_t up_irqbutton2(xcpt_t irqhandler); #endif #endif /* CONFIG_ARCH_BUTTONS */ #undef EXTERN #if defined(__cplusplus) } #endif #endif /* __ASSEMBLY__ */ #endif /* __ARCH_BOARD_BOARD_H */