############################################################################ # configs/hymini-stm32v/nx/defconfig # # Copyright (C) 2011-2012 Gregory Nutt. All rights reserved. # Author: Gregory Nutt # # Redistribution and use in source and binary forms, with or without # modification, are permitted provided that the following conditions # are met: # # 1. Redistributions of source code must retain the above copyright # notice, this list of conditions and the following disclaimer. # 2. Redistributions in binary form must reproduce the above copyright # notice, this list of conditions and the following disclaimer in # the documentation and/or other materials provided with the # distribution. # 3. Neither the name NuttX nor the names of its contributors may be # used to endorse or promote products derived from this software # without specific prior written permission. # # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS # "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT # LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS # FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE # COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, # INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, # BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS # OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED # AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT # LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN # ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE # POSSIBILITY OF SUCH DAMAGE. # ############################################################################ # # Architecture Selection # CONFIG_ARCH="arm" CONFIG_ARCH_ARM=y CONFIG_ARCH_CORTEXM3=y CONFIG_ARCH_CHIP="stm32" CONFIG_ARCH_CHIP_STM32F103VCT6=y CONFIG_ARCH_BOARD="hymini-stm32v" CONFIG_ARCH_BOARD_HYMINI_STM32V=y CONFIG_BOARD_LOOPSPERMSEC=5483 CONFIG_DRAM_SIZE=49152 CONFIG_DRAM_START=0x20000000 CONFIG_ARCH_IRQPRIO=y CONFIG_ARCH_INTERRUPTSTACK=0 CONFIG_ARCH_STACKDUMP=y CONFIG_ARCH_BOOTLOADER=n CONFIG_ARCH_LEDS=y CONFIG_ARCH_BUTTONS=n CONFIG_ARCH_CALIBRATION=n CONFIG_ARCH_DMA=y # # Identify toolchain and linker options # CONFIG_STM32_CODESOURCERYW=n CONFIG_STM32_CODESOURCERYL=y CONFIG_STM32_DEVKITARM=n CONFIG_STM32_RAISONANCE=n CONFIG_STM32_BUILDROOT=n CONFIG_STM32_DFU=n # # Individual subsystems can be enabled: # AHB: CONFIG_STM32_DMA1=n CONFIG_STM32_DMA2=y CONFIG_STM32_CRC=n CONFIG_STM32_FSMC=y CONFIG_STM32_SDIO=y # APB1: CONFIG_STM32_TIM2=n CONFIG_STM32_TIM3=n CONFIG_STM32_TIM4=n CONFIG_STM32_TIM5=n CONFIG_STM32_TIM6=n CONFIG_STM32_TIM7=n CONFIG_STM32_WWDG=n CONFIG_STM32_IWDG=n CONFIG_STM32_SPI2=n CONFIG_STM32_SPI4=n CONFIG_STM32_USART2=y CONFIG_STM32_USART3=n CONFIG_STM32_UART4=n CONFIG_STM32_UART5=n CONFIG_STM32_I2C1=y CONFIG_STM32_I2C2=n CONFIG_STM32_USB=y CONFIG_STM32_CAN1=n CONFIG_STM32_BKP=n CONFIG_STM32_PWR=n CONFIG_STM32_DAC=n # APB2: CONFIG_STM32_ADC1=n CONFIG_STM32_ADC2=n CONFIG_STM32_TIM1=n CONFIG_STM32_SPI1=n CONFIG_STM32_TIM8=n CONFIG_STM32_USART1=y CONFIG_STM32_ADC3=n # # Timer and I2C devices may need to the following to force power to be applied: # #CONFIG_STM32_FORCEPOWER=y # # STM32F103V specific serial device driver settings # CONFIG_USART1_SERIAL_CONSOLE=y CONFIG_USART2_SERIAL_CONSOLE=n CONFIG_USART3_SERIAL_CONSOLE=n CONFIG_UART4_SERIAL_CONSOLE=n CONFIG_UART5_SERIAL_CONSOLE=n CONFIG_USART1_TXBUFSIZE=256 CONFIG_USART2_TXBUFSIZE=256 CONFIG_USART3_TXBUFSIZE=256 CONFIG_UART4_TXBUFSIZE=256 CONFIG_UART5_TXBUFSIZE=256 CONFIG_USART1_RXBUFSIZE=256 CONFIG_USART2_RXBUFSIZE=256 CONFIG_USART3_RXBUFSIZE=256 CONFIG_UART4_RXBUFSIZE=256 CONFIG_UART5_RXBUFSIZE=256 CONFIG_USART1_BAUD=115200 CONFIG_USART2_BAUD=115200 CONFIG_USART3_BAUD=115200 CONFIG_UART4_BAUD=115200 CONFIG_UART5_BAUD=115200 CONFIG_USART1_BITS=8 CONFIG_USART2_BITS=8 CONFIG_USART3_BITS=8 CONFIG_UART4_BITS=8 CONFIG_UART5_BITS=8 CONFIG_USART1_PARITY=0 CONFIG_USART2_PARITY=0 CONFIG_USART3_PARITY=0 CONFIG_UART4_PARITY=0 CONFIG_UART5_PARITY=0 CONFIG_USART1_2STOP=0 CONFIG_USART2_2STOP=0 CONFIG_USART3_2STOP=0 CONFIG_UART4_2STOP=0 CONFIG_UART5_2STOP=0 # # General build options # CONFIG_RRLOAD_BINARY=n CONFIG_INTELHEX_BINARY=y CONFIG_MOTOROLA_SREC=n CONFIG_RAW_BINARY=n CONFIG_HAVE_LIBM=n # # General OS setup # CONFIG_USER_ENTRYPOINT="nx_main" CONFIG_DEBUG=n CONFIG_DEBUG_VERBOSE=n CONFIG_DEBUG_GRAPHICS=n CONFIG_DEBUG_LCD=n CONFIG_DEBUG_SYMBOLS=n CONFIG_MM_REGIONS=1 CONFIG_ARCH_LOWPUTC=y CONFIG_RR_INTERVAL=200 CONFIG_SCHED_INSTRUMENTATION=n CONFIG_TASK_NAME_SIZE=0 CONFIG_START_YEAR=2011 CONFIG_START_MONTH=7 CONFIG_START_DAY=5 CONFIG_GREGORIAN_TIME=n CONFIG_JULIAN_TIME=n CONFIG_DEV_CONSOLE=y CONFIG_DEV_LOWCONSOLE=n CONFIG_MUTEX_TYPES=n CONFIG_PRIORITY_INHERITANCE=n CONFIG_SEM_PREALLOCHOLDERS=0 CONFIG_SEM_NNESTPRIO=0 CONFIG_FDCLONE_DISABLE=n CONFIG_FDCLONE_STDIO=n CONFIG_SDCLONE_DISABLE=y CONFIG_SCHED_WORKQUEUE=y CONFIG_SCHED_WORKPRIORITY=192 CONFIG_SCHED_WORKPERIOD=50000 CONFIG_SCHED_WORKSTACKSIZE=1024 CONFIG_SIG_SIGWORK=4 # # Settings for NXFLAT # CONFIG_NXFLAT=n CONFIG_NXFLAT_DUMPBUFFER=n CONFIG_SYMTAB_ORDEREDBYNAME=y # # The following can be used to disable categories of # APIs supported by the OS. If the compiler supports # weak functions, then it should not be necessary to # disable functions unless you want to restrict usage # of those APIs. # # There are certain dependency relationships in these # features. # # o mq_notify logic depends on signals to awaken tasks # waiting for queues to become full or empty. # o pthread_condtimedwait() depends on signals to wake # up waiting tasks. # CONFIG_DISABLE_CLOCK=n CONFIG_DISABLE_POSIX_TIMERS=y CONFIG_DISABLE_PTHREAD=n CONFIG_DISABLE_SIGNALS=n CONFIG_DISABLE_MQUEUE=n CONFIG_DISABLE_MOUNTPOINT=y CONFIG_DISABLE_ENVIRON=y CONFIG_DISABLE_POLL=y # # Misc libc settings # CONFIG_NOPRINTF_FIELDWIDTH=n # # Allow for architecture optimized implementations # # The architecture can provide optimized versions of the # following to improve system performance # CONFIG_ARCH_MEMCPY=n CONFIG_ARCH_MEMCMP=n CONFIG_ARCH_MEMMOVE=n CONFIG_ARCH_MEMSET=n CONFIG_ARCH_STRCMP=n CONFIG_ARCH_STRCPY=n CONFIG_ARCH_STRNCPY=n CONFIG_ARCH_STRLEN=n CONFIG_ARCH_STRNLEN=n CONFIG_ARCH_BZERO=n # # Sizes of configurable things (0 disables) # CONFIG_MAX_TASKS=16 CONFIG_MAX_TASK_ARGS=4 CONFIG_NPTHREAD_KEYS=4 CONFIG_NFILE_DESCRIPTORS=8 CONFIG_NFILE_STREAMS=8 CONFIG_NAME_MAX=32 CONFIG_STDIO_BUFFER_SIZE=256 CONFIG_NUNGET_CHARS=2 CONFIG_PREALLOC_MQ_MSGS=4 CONFIG_MQ_MAXMSGSIZE=32 CONFIG_MAX_WDOGPARMS=2 CONFIG_PREALLOC_WDOGS=4 CONFIG_PREALLOC_TIMERS=4 # # Framebuffer driver options # CONFIG_FB_CMAP=n CONFIG_FB_HWCURSOR=n CONFIG_FB_HWCURSORIMAGE=n #CONFIG_FB_HWCURSORSIZE #CONFIG_FB_TRANSPARENCY # # Filesystem configuration # CONFIG_FS_FAT=n CONFIG_FAT_LCNAMES=n CONFIG_FAT_LFN=n CONFIG_FAT_MAXFNAME=32 CONFIG_FS_NXFFS=n CONFIG_FS_ROMFS=n # # SPI-based MMC/SD driver # CONFIG_MMCSD_NSLOTS=1 CONFIG_MMCSD_READONLY=n CONFIG_MMCSD_SPICLOCK=12500000 # # Block driver buffering # CONFIG_FS_READAHEAD=n CONFIG_FS_WRITEBUFFER=n # # SDIO-based MMC/SD driver # CONFIG_SDIO_DMA=y CONFIG_MMCSD_MMCSUPPORT=n CONFIG_MMCSD_HAVECARDDETECT=n # # TCP/IP and UDP support via uIP # CONFIG_NET=n CONFIG_NET_IPv6=n CONFIG_NSOCKET_DESCRIPTORS=0 CONFIG_NET_SOCKOPTS=y CONFIG_NET_BUFSIZE=420 CONFIG_NET_TCP=n CONFIG_NET_TCP_CONNS=40 CONFIG_NET_MAX_LISTENPORTS=40 CONFIG_NET_UDP=n CONFIG_NET_UDP_CHECKSUMS=y #CONFIG_NET_UDP_CONNS=10 CONFIG_NET_ICMP=n CONFIG_NET_ICMP_PING=n #CONFIG_NET_PINGADDRCONF=0 CONFIG_NET_STATISTICS=y #CONFIG_NET_RECEIVE_WINDOW= #CONFIG_NET_ARPTAB_SIZE=8 CONFIG_NET_BROADCAST=n # # UIP Network Utilities # CONFIG_NET_DHCP_LIGHT=n CONFIG_NET_RESOLV_ENTRIES=4 # # USB Device Configuration # CONFIG_USBDEV=n CONFIG_USBDEV_ISOCHRONOUS=n CONFIG_USBDEV_DUALSPEED=n CONFIG_USBDEV_SELFPOWERED=y CONFIG_USBDEV_REMOTEWAKEUP=n CONFIG_USBDEV_MAXPOWER=100 CONFIG_USBDEV_TRACE=n CONFIG_USBDEV_TRACE_NRECORDS=128 # # USB Serial Device Configuration # CONFIG_PL2303=n CONFIG_PL2303_EPINTIN=1 CONFIG_PL2303_EPBULKOUT=2 CONFIG_PL2303_EPBULKIN=3 CONFIG_PL2303_NWRREQS=4 CONFIG_PL2303_NRDREQS=4 CONFIG_PL2303_VENDORID=0x067b CONFIG_PL2303_PRODUCTID=0x2303 CONFIG_PL2303_VENDORSTR="Nuttx" CONFIG_PL2303_PRODUCTSTR="USBdev Serial" CONFIG_PL2303_RXBUFSIZE=512 CONFIG_PL2303_TXBUFSIZE=512 # # USB Storage Device Configuration # CONFIG_USBMSC=n CONFIG_USBMSC_EP0MAXPACKET=64 CONFIG_USBMSC_EPBULKOUT=2 CONFIG_USBMSC_EPBULKIN=5 CONFIG_USBMSC_NRDREQS=2 CONFIG_USBMSC_NWRREQS=2 CONFIG_USBMSC_BULKINREQLEN=256 CONFIG_USBMSC_BULKOUTREQLEN=256 CONFIG_USBMSC_VENDORID=0x584e CONFIG_USBMSC_VENDORSTR="NuttX" CONFIG_USBMSC_PRODUCTID=0x5342 CONFIG_USBMSC_PRODUCTSTR="USBdev Storage" CONFIG_USBMSC_VERSIONNO=0x0399 CONFIG_USBMSC_REMOVABLE=y # # Watchdog timer configuration # CONFIG_WATCHDOG=n # # Graphics related configuration settings # CONFIG_NX=y CONFIG_NX_MULTIUSER=n CONFIG_NX_NPLANES=1 CONFIG_NX_DISABLE_1BPP=y CONFIG_NX_DISABLE_2BPP=y CONFIG_NX_DISABLE_4BPP=y CONFIG_NX_DISABLE_8BPP=y CONFIG_NX_DISABLE_16BPP=n CONFIG_NX_DISABLE_24BPP=y CONFIG_NX_DISABLE_32BPP=y CONFIG_NX_PACKEDMSFIRST=n CONFIG_NX_LCDDRIVER=y CONFIG_LCD_MAXPOWER=1 CONFIG_LCD_MAXCONTRAST=1 CONFIG_NX_MOUSE=y CONFIG_NX_KBD=y #CONFIG_NXTK_BORDERWIDTH=4 CONFIG_NXTK_BORDERCOLOR1=0xd69a CONFIG_NXTK_BORDERCOLOR2=0xad55 CONFIG_NXTK_AUTORAISE=n CONFIG_NXFONT_SANS22X29=n CONFIG_NXFONT_SANS23X27=y CONFIG_NXFONT_SANS28X37=n CONFIG_NXFONT_SANS22X29B=n CONFIG_NXFONT_SANS28X37B=n CONFIG_NXFONT_SANS40X49B=n CONFIG_NXFONT_SERIF22X29=n CONFIG_NXFONT_SERIF29X37=n CONFIG_NXFONT_SERIF38X48=n CONFIG_NXFONT_SERIF22X28B=n CONFIG_NXFONT_SERIF27X38B=n CONFIG_NXFONT_SERIF38X49B=n CONFIG_NXFONTS_CHARBITS=7 CONFIG_NX_BLOCKING=y CONFIG_NX_MXSERVERMSGS=32 CONFIG_NX_MXCLIENTMSGS=16 # # LCD Hardware Configuration # CONFIG_LCD_LANDSCAPE=n CONFIG_LCD_PORTRAIT=n CONFIG_LCD_RPORTRAIT=y CONFIG_LCD_BACKLIGHT=n # # Settings for examples/uip # CONFIG_EXAMPLES_UIP_IPADDR=0x0a000002 CONFIG_EXAMPLES_UIP_DRIPADDR=0x0a000001 CONFIG_EXAMPLES_UIP_NETMASK=0xffffff00 CONFIG_EXAMPLES_UIP_DHCPC=n # # Settings for examples/nettest CONFIG_EXAMPLES_NETTEST_SERVER=n CONFIG_EXAMPLES_NETTEST_PERFORMANCE=n CONFIG_EXAMPLES_NETTEST_NOMAC=n CONFIG_EXAMPLES_NETTEST_IPADDR=0x0a000002 CONFIG_EXAMPLES_NETTEST_DRIPADDR=0x0a000001 CONFIG_EXAMPLES_NETTEST_NETMASK=0xffffff00 CONFIG_EXAMPLES_NETTEST_CLIENTIP=0x0a000001 # # Settings for examples/ostest # CONFIG_EXAMPLES_OSTEST_LOOPS=1 CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048 CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3 # # Settings for apps/nshlib # CONFIG_NSH_FILEIOSIZE=512 CONFIG_NSH_STRERROR=n CONFIG_NSH_LINELEN=64 CONFIG_NSH_NESTDEPTH=3 CONFIG_NSH_DISABLESCRIPT=n CONFIG_NSH_DISABLEBG=n CONFIG_NSH_ROMFSETC=n CONFIG_NSH_CONSOLE=y #CONFIG_NSH_CONDEV="/dev/ttyS1" CONFIG_NSH_TELNET=n CONFIG_NSH_ARCHINIT=y CONFIG_NSH_IOBUFFER_SIZE=512 CONFIG_NSH_DHCPC=n CONFIG_NSH_NOMAC=n CONFIG_NSH_IPADDR=0x0a000002 CONFIG_NSH_DRIPADDR=0x0a000001 CONFIG_NSH_NETMASK=0xffffff00 CONFIG_NSH_ROMFSMOUNTPT="/etc" CONFIG_NSH_INITSCRIPT="init.d/rcS" CONFIG_NSH_ROMFSDEVNO=0 CONFIG_NSH_ROMFSSECTSIZE=64 CONFIG_NSH_FATDEVNO=1 CONFIG_NSH_FATSECTSIZE=512 CONFIG_NSH_FATNSECTORS=1024 CONFIG_NSH_FATMOUNTPT="/tmp" # # Architecture-specific NSH options # CONFIG_NSH_MMCSDSPIPORTNO=0 CONFIG_NSH_MMCSDSLOTNO=0 CONFIG_NSH_MMCSDMINOR=0 # # Settings for examples/usbserial # CONFIG_EXAMPLES_USBSERIAL_INONLY=n CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n # # Settings for examples/nx # CONFIG_EXAMPLES_NX_BUILTIN=n CONFIG_EXAMPLES_NX_VPLANE=0 CONFIG_EXAMPLES_NX_DEVNO=0 CONFIG_EXAMPLES_NX_BGCOLOR=0x0011 CONFIG_EXAMPLES_NX_COLOR1=0xaedc CONFIG_EXAMPLES_NX_COLOR2=0xe7ff CONFIG_EXAMPLES_NX_TBCOLOR=0xd69a CONFIG_EXAMPLES_NX_FONTID=0 CONFIG_EXAMPLES_NX_FONTCOLOR=0x0000 CONFIG_EXAMPLES_NX_BPP=16 CONFIG_EXAMPLES_NX_RAWWINDOWS=n CONFIG_EXAMPLES_NX_STACKSIZE=2048 CONFIG_EXAMPLES_NX_CLIENTPRIO=80 CONFIG_EXAMPLES_NX_SERVERPRIO=120 CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4 CONFIG_EXAMPLES_NX_EXTERNINIT=n # # Settings for examples/nximage # CONFIG_EXAMPLES_NXIMAGE_BUILTIN=n CONFIG_EXAMPLES_NXIMAGE_VPLANE=0 CONFIG_EXAMPLES_NXIMAGE_DEVNO=0 CONFIG_EXAMPLES_NXIMAGE_BPP=16 CONFIG_EXAMPLES_NXIMAGE_XSCALEp5=n CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5=y CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0=n CONFIG_EXAMPLES_NXIMAGE_YSCALEp5=n CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5=y CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0=n CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT=n # # Settings for examples/nxlines # CONFIG_EXAMPLES_NXLINES_BUILTIN=n CONFIG_EXAMPLES_NXLINES_VPLANE=0 CONFIG_EXAMPLES_NXLINES_DEVNO=0 CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320 CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16 CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0 CONFIG_EXAMPLES_NXLINES_BPP=16 CONFIG_EXAMPLES_NXLINES_EXTERNINIT=n # # Settings for examples/watchdog # # This test depends on these specific Watchdog/NSH configurations settings (your # specific watchdog hardware settings might require additional settings). # # # Stack and heap information # CONFIG_BOOT_RUNFROMFLASH=n CONFIG_BOOT_COPYTORAM=n CONFIG_CUSTOM_STACK=n CONFIG_IDLETHREAD_STACKSIZE=1024 CONFIG_USERMAIN_STACKSIZE=2048 CONFIG_PTHREAD_STACK_MIN=256 CONFIG_PTHREAD_STACK_DEFAULT=2048 CONFIG_HEAP_BASE= CONFIG_HEAP_SIZE=