================== Espressif ESP32-S3 ================== The ESP32-S3 is a series of single and dual-core SoCs from Espressif based on Harvard architecture Xtensa LX7 CPUs and with on-chip support for Bluetooth and Wi-Fi. All embedded memory, external memory and peripherals are located on the data bus and/or the instruction bus of these CPUs. With some minor exceptions, the address mapping of two CPUs is symmetric, meaning they use the same addresses to access the same memory. Multiple peripherals in the system can access embedded memory via DMA. On dual-core SoCs, the two CPUs are typically named "PRO_CPU" and "APP_CPU" (for "protocol" and "application"), however for most purposes the two CPUs are interchangeable. ESP32-S3 Toolchain ================== The toolchain used to build ESP32-S3 firmware can be either downloaded or built from the sources. It is **highly** recommended to use (download or build) the same toolchain version that is being used by the NuttX CI. Please refer to the Docker `container `_ and check for the current compiler version being used. For instance: .. code-block:: ############################################################################### # Build image for tool required by ESP32 builds ############################################################################### FROM nuttx-toolchain-base AS nuttx-toolchain-esp32 # Download the latest ESP32 GCC toolchain prebuilt by Espressif RUN mkdir -p xtensa-esp32-elf-gcc && \ curl -s -L "https://github.com/espressif/crosstool-NG/releases/download/esp-12.2.0_20230208/xtensa-esp32-elf-12.2.0_20230208-x86_64-linux-gnu.tar.xz" \ | tar -C xtensa-esp32-elf-gcc --strip-components 1 -xJ RUN mkdir -p xtensa-esp32s2-elf-gcc && \ curl -s -L "https://github.com/espressif/crosstool-NG/releases/download/esp-12.2.0_20230208/xtensa-esp32s2-elf-12.2.0_20230208-x86_64-linux-gnu.tar.xz" \ | tar -C xtensa-esp32s2-elf-gcc --strip-components 1 -xJ RUN mkdir -p xtensa-esp32s3-elf-gcc && \ curl -s -L "https://github.com/espressif/crosstool-NG/releases/download/esp-12.2.0_20230208/xtensa-esp32s3-elf-12.2.0_20230208-x86_64-linux-gnu.tar.xz" \ | tar -C xtensa-esp32s3-elf-gcc --strip-components 1 -xJ For ESP32-S3, the toolchain version is based on GGC 12.2.0 (``xtensa-esp32s3-elf-12.2.0_20230208``) The prebuilt Toolchain (Recommended) ------------------------------------ First, create a directory to hold the toolchain: .. code-block:: console $ mkdir -p /path/to/your/toolchain/xtensa-esp32s3-elf-gcc Download and extract toolchain: .. code-block:: console $ curl -s -L "https://github.com/espressif/crosstool-NG/releases/download/esp-12.2.0_20230208/xtensa-esp32s3-elf-12.2.0_20230208-x86_64-linux-gnu.tar.xz" \ | tar -C xtensa-esp32s3-elf-gcc --strip-components 1 -xJ Add the toolchain to your `PATH`: .. code-block:: console $ echo "export PATH=/path/to/your/toolchain/xtensa-esp32s3-elf-gcc/bin:$PATH" >> ~/.bashrc You can edit your shell's rc files if you don't use bash. Building from source -------------------- You can also build the toolchain yourself. The steps to build the toolchain with crosstool-NG on Linux are as follows .. code-block:: console $ git clone https://github.com/espressif/crosstool-NG.git $ cd crosstool-NG $ git submodule update --init $ ./bootstrap && ./configure --enable-local && make $ ./ct-ng xtensa-esp32s3-elf $ ./ct-ng build $ chmod -R u+w builds/xtensa-esp32s3-elf $ export PATH="crosstool-NG/builds/xtensa-esp32-elf/bin:$PATH" These steps are given in the setup guide in `ESP-IDF documentation `_. Building and flashing NuttX =========================== Bootloader and partitions ------------------------- Nuttx can boot the ESP32-S3 directly using the so-called "Simple Boot". An externally-built 2nd stage bootloader is not required in this case as all functions required to boot the device are built within Nuttx. Simple boot does not require any specific configuration (it is selectable by default if no other 2nd stage bootloader is used). If other features are required, an externally-built 2nd stage bootloader is needed. The bootloader is built using the ``make bootloader`` command. This command generates the firmware in the ``nuttx`` folder. The ``ESPTOOL_BINDIR`` is used in the ``make flash`` command to specify the path to the bootloader. For compatibility among other SoCs and future options of 2nd stage bootloaders, the commands ``make bootloader`` and the ``ESPTOOL_BINDIR`` option (for the ``make flash``) can be used even if no externally-built 2nd stage bootloader is being built (they will be ignored if Simple Boot is used, for instance):: $ make bootloader .. note:: It is recommended that if this is the first time you are using the board with NuttX to perform a complete SPI FLASH erase. .. code-block:: console $ esptool.py erase_flash Building and Flashing --------------------- First, make sure that ``esptool.py`` is installed. This tool is used to convert the ELF to a compatible ESP32-S3 image and to flash the image into the board. It can be installed with: ``pip install esptool==4.8.dev4``. It's a two-step process where the first converts the ELF file into an ESP32-S3 compatible binary and the second flashes it to the board. These steps are included in the build system and it is possible to build and flash the NuttX firmware simply by running:: $ make flash ESPTOOL_PORT= ESPTOOL_BINDIR=./ where ```` is typically ``/dev/ttyUSB0`` or similar. ``ESPTOOL_BINDIR=./`` is the path of the externally-built 2nd stage bootloader and the partition table (if applicable): when built using the ``make bootloader``, these files are placed into ``nuttx`` folder. ``ESPTOOL_BAUD`` is able to change the flash baudrate if desired. Peripheral Support ================== The following list indicates the state of peripherals' support in NuttX: ========== ======= ===== Peripheral Support NOTES ========== ======= ===== ADC YES AES YES Bluetooth No CAMERA No CAN/TWAI Yes DMA Yes eFuse No GPIO Yes I2C No I2S Yes LCD No LED_PWM No MCPWM No Pulse_CNT No RMT No RNG No RSA No RTC Yes SD/MMC No SDIO No SHA No SPI Yes SPIFLASH Yes SPIRAM Yes Timers Yes Touch Yes UART Yes USB OTG No USB SERIAL Yes Watchdog Yes Wi-Fi Yes WPA3-SAE supported ========== ======= ===== .. _esp32s3_peripheral_support: Wi-Fi ----- .. tip:: Boards usually expose a ``wifi`` defconfig which enables Wi-Fi. On ESP32-S3, SMP is enabled to enhance Wi-Fi performance. A standard network interface will be configured and can be initialized such as:: nsh> ifup wlan0 nsh> wapi psk wlan0 mypasswd 3 nsh> wapi essid wlan0 myssid 1 nsh> renew wlan0 In this case a connection to AP with SSID ``myssid`` is done, using ``mypasswd`` as password. IP address is obtained via DHCP using ``renew`` command. You can check the result by running ``ifconfig`` afterwards. .. tip:: Please refer to :ref:`ESP32 Wi-Fi Station Mode ` for more information. Wi-Fi SoftAP ------------ It is possible to use ESP32-S3 as an Access Point (SoftAP). .. tip:: Boards usually expose a ``sta_softap`` defconfig which enables Wi-Fi (STA + SoftAP). On ESP32-S3, SMP is enabled to enhance Wi-Fi performance. If you are using this board config profile you can run these commands to be able to connect your smartphone or laptop to your board:: nsh> ifup wlan1 nsh> dhcpd_start wlan1 nsh> wapi psk wlan1 mypasswd 3 nsh> wapi essid wlan1 nuttxap 1 In this case, you are creating the access point ``nuttxapp`` in your board and to connect to it on your smartphone you will be required to type the password ``mypasswd`` using WPA2. .. tip:: Please refer to :ref:`ESP32 Wi-Fi SoftAP Mode ` for more information. The ``dhcpd_start`` is necessary to let your board to associate an IP to your smartphone. Supported Boards ================ .. toctree:: :glob: :maxdepth: 1 boards/*/*