/************************************************************************************ * configs/stm32f746g-disco/include/board.h * * Copyright (C) 2015 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ************************************************************************************/ #ifndef __CONFIG_STM32F746G_DISCO_INCLUDE_BOARD_H #define __CONFIG_STM32F746G_DISCO_INCLUDE_BOARD_H /************************************************************************************ * Included Files ************************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif #include "stm32_rcc.h" #ifdef CONFIG_STM32F7_SDMMC1 # include "stm32_sdmmc.h" #endif /************************************************************************************ * Pre-processor Definitions ************************************************************************************/ /* Clocking *************************************************************************/ /* The STM32F7 Discovery board features a single 8MHz crystal. Space is provided * for a 32kHz RTC backup crystal, but it is not stuffed. * * This is the canonical configuration: * System Clock source : PLL (HSE) * SYSCLK(Hz) : 180000000 Determined by PLL configuration * HCLK(Hz) : 180000000 (STM32_RCC_CFGR_HPRE) * AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE) * APB1 Prescaler : 4 (STM32_RCC_CFGR_PPRE1) * APB2 Prescaler : 2 (STM32_RCC_CFGR_PPRE2) * HSE Frequency(Hz) : 8000000 (STM32_BOARD_XTAL) * PLLM : 8 (STM32_PLLCFG_PLLM) * PLLN : 336 (STM32_PLLCFG_PLLN) * PLLP : 2 (STM32_PLLCFG_PLLP) * PLLQ : 7 (STM32_PLLCFG_PLLQ) * Main regulator output voltage : Scale1 mode Needed for high speed SYSCLK * Flash Latency(WS) : 5 * Prefetch Buffer : OFF * Instruction cache : ON * Data cache : ON * Require 48MHz for USB OTG FS, : Enabled * SDIO and RNG clock */ /* HSI - 16 MHz RC factory-trimmed * LSI - 32 KHz RC * HSE - On-board crystal frequency is 8MHz * LSE - 32.768 kHz */ #define STM32_BOARD_XTAL 8000000ul #define STM32_HSI_FREQUENCY 16000000ul #define STM32_LSI_FREQUENCY 32000 #define STM32_HSE_FREQUENCY STM32_BOARD_XTAL #define STM32_LSE_FREQUENCY 32768 /* Main PLL Configuration. * * PLL source is HSE * PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN * = (8,000,000 / 8) * 336 * = 336,000,000 * SYSCLK = PLL_VCO / PLLP * = 336,000,000 / 2 = 168,000,000 * USB OTG FS, SDIO and RNG Clock * = PLL_VCO / PLLQ * = 48,000,000 */ #define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(8) #define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336) #define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2 #define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7) #define STM32_SYSCLK_FREQUENCY 168000000ul /* AHB clock (HCLK) is SYSCLK (168MHz) */ #define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */ #define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY #define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */ /* APB1 clock (PCLK1) is HCLK/4 (42MHz) */ #define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */ #define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4) /* Timers driven from APB1 will be twice PCLK1 */ #define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY) /* APB2 clock (PCLK2) is HCLK/2 (84MHz) */ #define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */ #define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2) /* Timers driven from APB2 will be twice PCLK2 */ #define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK2_FREQUENCY) /* Timer Frequencies, if APBx is set to 1, frequency is same to APBx * otherwise frequency is 2xAPBx. * Note: TIM1,8 are on APB2, others on APB1 */ #define STM32_TIM18_FREQUENCY STM32_HCLK_FREQUENCY #define STM32_TIM27_FREQUENCY (STM32_HCLK_FREQUENCY/2) /* LED definitions ******************************************************************/ /* The STM32F746G-DISCO board has numerous LEDs but only one, LD1 located near the * reset button, that can be controlled by software (LD2 is a power indicator, LD3-6 * indicate USB status, LD7 is controlled by the ST-Link). * * LD1 is controlled by PI1 which is also the SPI2_SCK at the Arduino interface. * One end of LD1 is grounded so a high output on PI1 willilluminate the LED. * * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way. * The following definitions are used to access individual LEDs. */ /* LED index values for use with stm32_setled() */ #define BOARD_LED1 0 #define BOARD_NLEDS 1 #define BOARD_LD1 BOARD_LED1 /* LED bits for use with stm32_setleds() */ #define BOARD_LED1_BIT (1 << BOARD_LED1) /* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in * include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related * events as follows: * * SYMBOL Meaning LD1 * ------------------- ----------------------- ------ * LED_STARTED NuttX has been started OFF * LED_HEAPALLOCATE Heap has been allocated OFF * LED_IRQSENABLED Interrupts enabled OFF * LED_STACKCREATED Idle stack created ON * LED_INIRQ In an interrupt N/C * LED_SIGNAL In a signal handler N/C * LED_ASSERTION An assertion failed N/C * LED_PANIC The system has crashed FLASH * * Thus is LD1 is statically on, NuttX has successfully booted and is, * apparently, running normally. If LD1 is flashing at approximately * 2Hz, then a fatal error has been detected and the system has halted. */ #define LED_STARTED 0 /* LD1=OFF */ #define LED_HEAPALLOCATE 0 /* LD1=OFF */ #define LED_IRQSENABLED 0 /* LD1=OFF */ #define LED_STACKCREATED 1 /* LD1=ON */ #define LED_INIRQ 2 /* LD1=no change */ #define LED_SIGNAL 2 /* LD1=no change */ #define LED_ASSERTION 2 /* LD1=no change */ #define LED_PANIC 3 /* LD1=flashing */ /* Button definitions ***************************************************************/ /* Pushbutton B1, labelled "User", is connected to GPIO PI11. A high value will be sensed when the button is depressed. /* The STM32F7 Discovery supports one button: */ #define BUTTON_USER 0 #define NUM_BUTTONS 1 #define BUTTON_USER_BIT (1 << BUTTON_USER) /* Alternate function pin selections ************************************************/ /* USART6: * * These configurations assume that you are using a standard Arduio RS-232 shield * with the serial interface with RX on pin D0 and TX on pin D1: * * -------- --------------- * STM32F7 * ARDUIONO FUNCTION GPIO * -- ----- --------- ----- * DO RX USART6_RX PC7 * D1 TX USART6_TX PC6 * -- ----- --------- ----- */ #warning Missing logic #define GPIO_USART6_RX ??? #define GPIO_USART6_TX ??? /************************************************************************************ * Public Data ************************************************************************************/ #ifndef __ASSEMBLY__ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /************************************************************************************ * Public Function Prototypes ************************************************************************************/ /************************************************************************************ * Name: stm32_boardinitialize * * Description: * All STM32 architectures must provide the following entry point. This entry point * is called early in the initialization -- after all memory has been configured * and mapped but before any devices have been initialized. * ************************************************************************************/ void stm32_boardinitialize(void); /************************************************************************************ * Name: stm32_ledinit, stm32_setled, and stm32_setleds * * Description: * If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board LEDs. If * CONFIG_ARCH_LEDS is not defined, then the following interfaces are available to * control the LEDs from user applications. * ************************************************************************************/ #ifndef CONFIG_ARCH_LEDS void stm32_ledinit(void); void stm32_setled(int led, bool ledon); void stm32_setleds(uint8_t ledset); #endif #undef EXTERN #if defined(__cplusplus) } #endif #endif /* __ASSEMBLY__ */ #endif /* __CONFIG_STM32F746G_DISCO_INCLUDE_BOARD_H */