/**************************************************************************** * boards/arm/stm32f0l0g0/nucleo-l073rz/include/board.h * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ #ifndef __BOARDS_ARM_STM32F0L0G0_NUCLEO_L073RZ_INCLUDE_BOARD_H #define __BOARDS_ARM_STM32F0L0G0_NUCLEO_L073RZ_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include # include #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Clocking *****************************************************************/ /* HSI - Internal 8 MHz RC Oscillator * LSI - 32 KHz RC * HSE - 8 MHz from MCO output of ST-LINK * LSE - 32.768 kHz */ #define STM32_BOARD_XTAL 8000000ul #define STM32_HSEBYP_ENABLE #define STM32_HSI_FREQUENCY 8000000ul #define STM32_LSI_FREQUENCY 32000 /* Between 30kHz and 60kHz */ #define STM32_HSE_FREQUENCY STM32_BOARD_XTAL #define STM32_LSE_FREQUENCY 32768 /* X2 on board */ /* PLL source is HSE/1, PLL multipler is 8: * PLL frequency is 8MHz (XTAL) x 8 = 64MHz */ #define STM32_CFGR_PLLSRC RCC_CFGR_PLLSRC #define STM32_CFGR_PLLXTPRE 0 #define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx8 #define STM32_PLL_FREQUENCY (8*STM32_BOARD_XTAL) /* Use the PLL and set the SYSCLK source to be the PLL/2 (32MHz) */ #define STM32_SYSCLK_SW RCC_CFGR_SW_PLL #define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL #define STM32_CFGR_PLLDIV RCC_CFGR_PLLDIV_2 #define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY/2 /* AHB clock (HCLK) is SYSCLK (32MHz) */ #define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK #define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY /* APB2 clock (PCLK2) is HCLK (32MHz) */ #define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK #define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY #define STM32_APB2_CLKIN (STM32_PCLK2_FREQUENCY) /* APB1 clock (PCLK1) is HCLK/2 (16MHz) */ #define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2 #define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2) /* 48MHz clock configuration */ #if defined(CONFIG_STM32F0L0G0_USB) || defined(CONFIG_STM32F0L0G0_RNG) # define STM32_USE_CLK48 1 # define STM32_CLK48_SEL RCC_CCIPR_CLK48SEL_HSI48 # define STM32_HSI48_SYNCSRC SYNCSRC_NONE #endif /* TODO: timers */ /* LED definitions **********************************************************/ /* The Nucleo LO73RZ board has three LEDs. Two of these are controlled by * logic on the board and are not available for software control: * * LD1 COM: LD1 default status is red. LD1 turns to green to indicate that * communications are in progress between the PC and the * ST-LINK/V2-1. * LD3 PWR: red LED indicates that the board is powered. * * And one can be controlled by software: * * User LD2: green LED is a user LED connected to the I/O PA5 of the * STM32LO73RZ. * * If CONFIG_ARCH_LEDS is not defined, then the user can control the LED in * any way. The following definition is used to access the LED. */ /* LED index values for use with board_userled() */ #define BOARD_LED1 0 /* User LD2 */ #define BOARD_NLEDS 1 /* LED bits for use with board_userled_all() */ #define BOARD_LED1_BIT (1 << BOARD_LED1) /* If CONFIG_ARCH_LEDs is defined, then NuttX will control the LED on board * the Nucleo LO73RZ. The following definitions describe how NuttX controls * the LED: * * SYMBOL Meaning LED1 state * ------------------ ----------------------- ---------- * LED_STARTED NuttX has been started OFF * LED_HEAPALLOCATE Heap has been allocated OFF * LED_IRQSENABLED Interrupts enabled OFF * LED_STACKCREATED Idle stack created ON * LED_INIRQ In an interrupt No change * LED_SIGNAL In a signal handler No change * LED_ASSERTION An assertion failed No change * LED_PANIC The system has crashed Blinking * LED_IDLE STM32 is is sleep mode Not used */ #define LED_STARTED 0 #define LED_HEAPALLOCATE 0 #define LED_IRQSENABLED 0 #define LED_STACKCREATED 1 #define LED_INIRQ 2 #define LED_SIGNAL 2 #define LED_ASSERTION 2 #define LED_PANIC 1 /* Button definitions *******************************************************/ /* The Nucleo LO73RZ supports two buttons; only one button is controllable * by software: * * B1 USER: user button connected to the I/O PC13 of the STM32LO73RZ. * B2 RESET: push button connected to NRST is used to RESET the * STM32LO73RZ. */ #define BUTTON_USER 0 #define NUM_BUTTONS 1 #define BUTTON_USER_BIT (1 << BUTTON_USER) /* Alternate function pin selections ****************************************/ /* I2C */ #define GPIO_I2C1_SCL GPIO_I2C1_SCL_2 /* D15 - PB8 */ #define GPIO_I2C1_SDA GPIO_I2C1_SDA_2 /* D14 - PB9 */ /* SPI1 */ #define GPIO_SPI1_MISO GPIO_SPI1_MISO_2 /* D12 - PA6 */ #define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_2 /* D11 - PA7 */ #define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 /* D13 - PA5 */ /* SPI2 */ #define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 /* PB14 */ #define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 /* PB15 */ #define GPIO_SPI2_SCK GPIO_SPI2_SCK_1 /* PB10 */ /* USART */ /* By default the USART2 is connected to STLINK Virtual COM Port: * USART2_RX - PA3 * USART2_TX - PA2 */ #define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */ #define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */ /* DMA channels *************************************************************/ /* ADC */ #define ADC1_DMA_CHAN DMACHAN_ADC1 /* DMA1_CH1 */ #endif /* __BOARDS_ARM_STM32F0L0G0_NUCLEO_LO73RZ_INCLUDE_BOARD_H */