#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

config ARCH_HAVE_SPI_CRCGENERATION
	bool
	default n

config ARCH_HAVE_SPI_CS_CONTROL
	bool
	default n

config ARCH_HAVE_SPI_BITORDER
	bool
	default n

config ARCH_HAVE_QSPI_BITORDER
	bool
	default n

config ARCH_HAVE_QSPI_WORD_REVERSE
	bool
	default n

menuconfig SPI
	bool "SPI Driver Support"
	default n
	---help---
		This selection enables selection of common SPI options.  This option
		should be enabled by all platforms that support SPI interfaces.
		See include/nuttx/spi/spi.h for further SPI driver information.

if SPI

config SPI_SLAVE
	bool "SPI Slave"
	default n
	---help---
		Enable support for SPI Slave features

if SPI_SLAVE

config SPI_SLAVE_DRIVER
	bool "SPI Slave character driver"
	default n
	---help---
		Built-in support for a character driver at /dev/spislv[N] that may be
		used to perform SPI bus transfers from applications.
		The intent of this driver is to support SPI Slave testing.

if SPI_SLAVE_DRIVER

config SPI_SLAVE_DRIVER_MODE
	int "SPI Slave character driver default mode"
	default 0
	---help---
		Default SPI Slave character driver mode, where:
		0 = CPOL=0, CPHA=0
		1 = CPOL=0, CPHA=1
		2 = CPOL=1, CPHA=0
		3 = CPOL=1, CPHA=1

config SPI_SLAVE_DRIVER_WIDTH
	int "SPI Slave character driver default bit width"
	default 8
	---help---
		Number of bits per SPI Slave transfer (default 8).

config SPI_SLAVE_DRIVER_BUFFER_SIZE
	int "SPI Slave character driver TX and RX buffer sizes"
	default 128
	---help---
		Size of the internal TX and RX buffers of the SPI Slave
		character driver.

config SPI_SLAVE_DRIVER_COLORIZE_TX_BUFFER
	bool "SPI Slave character driver colorize TX buffer"
	default n
	---help---
		Initialize entries of the TX buffer with a given pattern.
		If the SPI Slave controller performs a call to "getdata" API during
		the "bind" operation, the colorized buffer may be sent as part of the
		first TX transfer of the SPI Slave controller.
		This feature might be useful for a quick communication test between
		Master and Slave.

config SPI_SLAVE_DRIVER_COLORIZE_PATTERN
	hex "SPI Slave character driver colorize pattern"
	default 0xa5
	depends on SPI_SLAVE_DRIVER_COLORIZE_TX_BUFFER
	---help---
		Pattern to be used as the coloration of the TX buffer.

config SPI_SLAVE_DRIVER_COLORIZE_NUM_BYTES
	int "SPI Slave character driver colorize number of bytes"
	default 4
	depends on SPI_SLAVE_DRIVER_COLORIZE_TX_BUFFER
	---help---
		Number of bytes of the TX buffer to be colorized.

endif # SPI_SLAVE_DRIVER

config SPI_SLAVE_DMA
	bool "SPI Slave DMA"
	default n
	depends on ARCH_DMA && EXPERIMENTAL
	---help---
		Enable support for DMA data transfers (not yet implemented).

endif # SPI_SLAVE

config SPI_EXCHANGE
	bool "SPI exchange"
	default y
	---help---
		Driver supports a single exchange method (vs a recvblock() and
		sndblock() methods).

config SPI_CMDDATA
	bool "SPI CMD/DATA"
	default n
	---help---
		Devices on the SPI bus require out-of-band support to distinguish
		command transfers from data transfers.  Such devices will often support
		either 9-bit SPI (yech) or 8-bit SPI and a GPIO output that selects
		between command and data.

config SPI_CALLBACK
	bool "Media change callbacks"
	default y if MMCSD_SPI
	default n if !MMCSD_SPI
	---help---
		Support the callback method in the SPI interface.  This will allow
		the SPI-based MMC/SD driver to get a notification of changes in the
		card status when an SD card is inserted or removed.

config SPI_HWFEATURES
	bool
	default n
	---help---
		Selected only if a specific H/W feature is selected.  This is
		basically the OR of any specific hardware feature and enables
		the SPI hwfeatures() interface method.

config SPI_CRCGENERATION
	bool
	default n
	select SPI_HWFEATURES
	depends on ARCH_HAVE_SPI_CRCGENERATION
	---help---
		Selected by MCU Kconfig logic if implementation supports automatic
		generation of SPI CRCs.  Enables the HWFEAT_CRCGENERATION option
		as well as the hwfeartures() interface method.

config SPI_CS_CONTROL
	bool "SPI CS Behavior Control"
	default n
	select SPI_HWFEATURES
	depends on ARCH_HAVE_SPI_CS_CONTROL
	---help---
		Enables possibilities to define the behavior of CS.
		Also enables the hwfeatures() interface method.

config SPI_BITORDER
	bool "SPI Bit Order Control"
	default n
	select SPI_HWFEATURES
	depends on ARCH_HAVE_SPI_BITORDER
	---help---
		Enables capability to select MSB- or LSB-first hardware feature for
		data transfers.

config QSPI_HWFEATURES
	bool
	default n
	---help---
		Selected only if a specific H/W feature is selected.  This is
		basically the OR of any specific hardware feature and enables
		the QSPI hwfeatures() interface method.

config QSPI_BITORDER
	bool "QSPI Bit Order Control"
	default n
	select QSPI_HWFEATURES
	depends on ARCH_HAVE_QSPI_BITORDER
	---help---
		Enables capability to select MSB- or LSB-first hardware feature for
		data transfers.

config QSPI_WORD_REVERSE
	bool "QSPI word reverse Control"
	default n
	select QSPI_HWFEATURES
	depends on ARCH_HAVE_QSPI_WORD_REVERSE
	---help---
		Enables capability to word reverse hardware feature for
		data transfers.

config SPI_DELAY_CONTROL
	bool "SPI Delay Control"
	default n
	---help---
		Enables possibilities to define the SPI Delays such as
		SPI-ChipSelect-Delays and inter frame delays.

		SPI-ChipSelect-Delays: are the delay between ChipSelect assertion
		and first Data-Bit, the delay between the last Data-Bit and the
		de-assertion and the minimum delay between two ChipSelects.

		The inter-frame delays also know as Inter-Data Idleness, controls the
		delay between frames. (one transaction of nbits as configured with
		SPI_SETBITS).

		This option enables the setdelay() interface method.

config SPI_TRIGGER
	bool "SPI DMA trigger"
	default n
	select SPI_HWFEATURES
	depends on SPI_EXCHANGE
	---help---
		Some architectures benefit from delaying the start of DMA from the
		DMA setup.  If this option is selected, then an SPI_TRIGGER() method
		is supported:  The DMA is setup with in in SPI_EXCHANGE() but does
		not actually begin until SPI_TRIGGER() is called.

config SPI_DRIVER
	bool "SPI character driver"
	default n
	depends on SPI_EXCHANGE
	---help---
		Build in support for a character driver at /dev/spi[N] that may be
		used to perform SPI bus transfers from applications.  The intent of
		this driver is to support SPI testing.  It is not suitable for use
		in any real driver application.

config SPI_BITBANG
	bool "SPI bit-bang device"
	default n
	---help---
		Enable support for a generic SPI bit-bang device.
		See include/nuttx/spi/spi_bitbang.h for further information.

if SPI_BITBANG

config SPI_BITBANG_VARWIDTH
	bool "SPI bit-bang variable width transfers"
	default n
	---help---
		Enable support for a variable data width transfers.  Default: 8-bit
		only.

endif # SPI_BITBANG

config SPI_FLASH
	bool "Simulated SPI FLASH with SMARTFS"
	default n
	---help---
		Adds a simulated SPI FLASH that responds to standard M25 style
		commands on the SPI bus.

if SPI_FLASH

choice
	prompt "Simulated SPI FLASH Size"
	default SPI_FLASH_1M

config SPI_FLASH_1M
	bool "1 MBit (128K Byte)"

config SPI_FLASH_8M
	bool "8 MBit (1M Byte)"

config SPI_FLASH_32M
	bool "32 MBit (4M Byte)"

config SPI_FLASH_64M
	bool "64 MBit (8M Byte)"

config SPI_FLASH_128M
	bool "128 MBit (16M Byte)"

endchoice

config SPI_FLASH_SECTORSIZE
	int "FLASH Sector Erase Size"
	default 65536
	---help---
		Sets the large sector erase size that the part simulates.
		This driver simulates SPI devices that have both a large
		sector erase as well as a "sub-sector" (per the datasheet)
		erase size (typically 4K bytes).

config SPI_FLASH_SUBSECTORSIZE
	int "FLASH Sub-Sector Erase Size"
	default 4096
	---help---
		Sets the smaller sub-sector erase size supported by the
		FLASH emulation

config SPI_FLASH_M25P
	bool "Enable M25Pxx FLASH"
	---help---
		Enables simulation of an M25P type FLASH

config SPI_FLASH_SST26
	bool "Enable SST26 FLASH"
	---help---
		Enables simulation of an SST26 type FLASH

config SPI_FLASH_W25
	bool "Enable W25 FLASH"
	---help---
		Enables simulation of a W25 type FLASH

config SPI_FLASH_CUSTOM
	bool "Enable Emulation of a Custom Manufacturer / ID FLASH"
	---help---
		Enables simulation of FLASH with a custom Manufacturer, ID and Capacity

config SPI_FLASH_MANUFACTURER
	hex "Hex ID of the FLASH manufacturer code"
	default 0x20
	depends on SPI_FLASH_CUSTOM
	---help---
		Allows the simulated FLASH Manufacturer ID to be set.

config SPI_FLASH_MEMORY_TYPE
	hex "Hex ID of the FLASH Memory Type code"
	default 0x20
	depends on SPI_FLASH_CUSTOM
	---help---
		Allows the simulated FLASH Memory Type code to be set.

config SPI_FLASH_CAPACITY
	hex "Hex ID of the FLASH capacity code"
	default 0x14
	depends on SPI_FLASH_CUSTOM
	---help---
		Allows the simulated FLASH Memory Capacity code to be set.

config SPI_FLASH_PAGESIZE
	int "FLASH Write / Program Page Size"
	default 256
	---help---
		Sets the size of a page program operation.  The page size
		represents the maximum number of bytes that can be sent
		for a program operation.  If more bytes than this are
		sent on a single Page Program, then the address will
		"wrap" causing the initial data sent to be overwritten.
		This is consistent with standard SPI FLASH operation.

endif # SPI_FLASH

config QSPI_FLASH
	bool "Simulated QSPI FLASH with SMARTFS"
	default n
	---help---
		Adds a simulated QSPI FLASH that responds to N25QXXX style
		commands on the QSPI bus.

if QSPI_FLASH

choice
	prompt "Simulated QSPI FLASH Size"
	default QSPI_FLASH_1M

config QSPI_FLASH_1M
	bool "1 MBit (128K Byte)"

config QSPI_FLASH_8M
	bool "8 MBit (1M Byte)"

config QSPI_FLASH_32M
	bool "32 MBit (4M Byte)"

config QSPI_FLASH_64M
	bool "64 MBit (8M Byte)"

config QSPI_FLASH_128M
	bool "128 MBit (16M Byte)"

endchoice

config QSPI_FLASH_MANUFACTURER
	hex "Hex ID of the FLASH manufacturer code"
	default 0x20
	---help---
		Allows the simulated FLASH Manufacturer ID to be set.

config QSPI_FLASH_MEMORY_TYPE
	hex "Hex ID of the FLASH Memory Type code"
	default 0xba
	---help---
		Allows the simulated FLASH Memory Type code to be set.

config QSPI_FLASH_SECTORSIZE
	int "FLASH Sector Erase Size"
	default 65536
	---help---
		Sets the large sector erase size that the part simulates.
		This driver simulates QSPI devices that have both a large
		sector erase as well as a "sub-sector" (per the datasheet)
		erase size (typically 4K bytes).

config QSPI_FLASH_SUBSECTORSIZE
	int "FLASH Sub-Sector Erase Size"
	default 4096
	---help---
		Sets the smaller sub-sector erase size supported by the
		FLASH emulation

config QSPI_FLASH_PAGESIZE
	int "FLASH Write / Program Page Size"
	default 256
	---help---
		Sets the size of a page program operation.  The page size
		represents the maximum number of bytes that can be sent
		for a program operation.  If more bytes than this are
		sent on a single Page Program, then the address will
		"wrap" causing the initial data sent to be overwritten.
		This is consistent with standard SPI FLASH operation.

endif # QSPI_FLASH

endif # SPI