/************************************************************************************
 * configs/vsn/src/boot.c
 * arch/arm/src/board/boot.c
 *
 *   Copyright (C) 2009 Gregory Nutt. All rights reserved.
 *   Copyright (c) 2011 Uros Platise. All rights reserved.
 *
 *   Authors: Gregory Nutt <spudmonkey@racsa.co.cr>
 *            Uros Platise <uros.platise@isotel.eu>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ************************************************************************************/

/************************************************************************************
 * Included Files
 ************************************************************************************/

#include <nuttx/config.h>

#include <debug.h>

#include <arch/board/board.h>

#include "stm32_gpio.h"
#include "up_arch.h"
#include "vsn.h"

/************************************************************************************
 * Definitions
 ************************************************************************************/

/************************************************************************************
 * Private Functions
 ************************************************************************************/

/************************************************************************************
 * Public Functions
 ************************************************************************************/

/************************************************************************************
 * Name: stm32_boardinitialize
 *
 * Description:
 *   All STM32 architectures must provide the following entry point.  This entry point
 *   is called early in the intitialization -- after all memory has been configured
 *   and mapped but before any devices have been initialized.
 *
 ************************************************************************************/

void stm32_boardinitialize(void)
{
#ifdef CONFIG_STM32_SPI3
#warning JTAG Port Disabled as SPI3 NVRAM/FRAM support is enabled
  
  uint32_t val = getreg32(STM32_AFIO_MAPR);
  val &= 0x00FFFFFF;		// clear undefined readings ... 
  val |= AFIO_MAPR_DISAB;	// set JTAG-DP and SW-DP Disabled
  putreg32(val, STM32_AFIO_MAPR);
#endif

   // Set Board Voltage to 3.3 V
   board_power_setbootvoltage();

  /* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function
   * stm32_spiinitialize() has been brought into the link.
   */

#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2) || defined(CONFIG_STM32_SPI3)
  if (stm32_spiinitialize) stm32_spiinitialize();
#endif

   /* Initialize USB is 1) USBDEV is selected, 2) the USB controller is not
    * disabled, and 3) the weak function stm32_usbinitialize() has been brought
    * into the build.
    */

#if defined(CONFIG_USBDEV) && defined(CONFIG_STM32_USB)
  if (stm32_usbinitialize) stm32_usbinitialize();
#endif

  /* Configure on-board LEDs if LED support has been selected. */

#ifdef CONFIG_ARCH_LEDS
  up_ledinit();
#endif
}