======================== Adafruit KB2040 Key Boar ======================== The KB2040 Key Boar is a general purpose RP2040 board supplied by Adafruit. .. figure:: KB2040.png :align: center Features ======== * RP2040 microcontroller chip * Dual-core ARM Cortex M0+ processor, flexible clock running up to 133 MHz * 264kB of SRAM, and 8MB of on-board Flash memory * Castellated module allows soldering direct to carrier boards * USB Host and Device support via type C connector. * Low-power sleep and dormant modes * Drag & drop programming using mass storage over USB * 18 multi-function GPIO pins * 2× SPI, 2× I2C, 2× UART, 3× 12-bit ADC, 16× controllable PWM channels * Accurate clock and timer on-chip * Temperature sensor * Accelerated floating point libraries on-chip * 8 × Programmable IO (PIO) state machines for custom peripheral support * On-board STEMMA QT connector for quick I2C connection. Serial Console ============== By default a serial console appears on pins 1 (TX GPIO0) and pin 2 (RX GPIO1). This console runs a 115200-8N1. The board can be configured to use the USB connection as the serial console. Buttons and LEDs ================ There is a BOOT button which if held down when power is first applied or the RESET button is pressed will cause the RP2040 to boot into program mode and appear as a storage device to a USB connecte . Saving a .UF2 file to this device will replace the Flash ROM contents on the RP2040. A RESET button that allows rebooting the board without disconnecting the power. A ws2812 (NeoPixel) smart RGB LED controlled by GPIO17. Pin Mapping =========== Pads numbered anticlockwise from USB connector. ===== ========== ========== Pad Signal Notes ===== ========== ========== 1 D+ Alternate USB data connection. 2 GPIO0 Default TX for UART0 serial console 3 GPIO1 Default RX for UART1 serial console 4 Ground 5 Ground 6 GPIO2 7 GPIO3 8 GPIO4 9 GPIO5 10 GPIO6 11 GPIO7 12 GPIO8 13 GPIO9 14 GPIO10 15 GPIO19 16 GPIO20 17 GPIO18 18 GPIO26 ADC0 19 GPIO27 ADC1 20 GPIO28 ADC2 21 GPIO29 ADC3 22 Ground 23 Raw Connected to USB +5V line 24 D- Alternate USB data connection. ===== ========== ========== The board has a STEMMA QT connector that is also connected to pins GPI12 (I2C1 SDA) and GPI13 (I2C1 SDA). Power Supply ============ The Raspberry Pi Pico can be powered via the USB connector, or by supplying +5V to pin 23. The Raspberry Pi Pico chip run on 3.3 volts. This is supplied by an onboard voltage regulator. Configurations ============== audiopack --------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for NSPlayer audio player. composite --------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for CDC/ACM with MSC USB composite driver. displaypack ----------- NuttShell configuration (console enabled in USB Port, at 115200 bps) supporting ST7789 video display. enc28j60 -------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for NC28J60. lcd1602 ------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for LCD1602. nsh --- Basic NuttShell configuration (console enabled in UART0, at 115200 bps). nshsram ------- NuttShell configuration (console enabled in UART0, at 115200 bps) with interrupt vectors in RAM. smp --- Basic NuttShell configuration (console enabled in UART0, at 115200 bps) with both ARM cores enabled. spisd ----- NuttShell configuration (console enabled in UART0, at 115200 bps) with SPI configured. ssd1306 ------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for ssd1306. st7735 ------ NuttShell configuration (console enabled in UART0, at 115200 bps) with support for st7735. usbmsc ------ NuttShell configuration (console enabled in UART0, at 115200 bps) with support for usbmsc. usbnsh ------ Basic NuttShell configuration (console enabled in USB Port, at 115200 bps). waveshare-lcd-1.14 ------------------ NuttShell configuration (console enabled in UART0, at 115200 bps) with support for st7789. waveshare-lcd-1.3 ----------------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for usbmsc.