/**************************************************************************** * configs/lpcxpresso-lpc54628/include/board.h * * Copyright (C) 2017 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ #ifndef _CONFIGS_LPCXPRESSO_LPC54628_INCLUDE_BOARD_H #define _CONFIGS_LPCXPRESSO_LPC54628_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Clocking ****************************************************************/ #undef BOARD_180MHz #define BOARD_220MHz 1 /* System PLL * * Notation: * Fin = the input to the PLL. * Fout = the output of the PLL. * Fref = the PLL reference frequency, the input to the phase frequency * detector. * N = optional pre-divider value. * M = feedback divider value, which represents the multiplier for the * PLL. * P = optional post-divider value. An additional divide-by-2 is * included in the post-divider path. * * In all variations of normal mode, the following requirements must be met: * * -275 MHz ≤ Fcco ≤ 550 MHz. * 4 kHz ≤ Fin / N ≤ 25 MHz. * * Normal mode with optional pre-divide. In the equations, use N = 1 when * the pre-divider is not used. The extra divide by 2 is in the feedback * divider path: * * Fout = Fcco = 2 x M x Fin / N * * Normal mode with post-divide and optional pre-divide. In the equations, * use N = 1 when the pre-divider is not used: * * Fout = Fcco / (2 x P) = M x Fin / (N x P) */ #define BOARD_PLL_SOURCE /* Select source FR0 12MHz */ #define BOARD_PLL_FIN LPC54_FRO_12MHZ /* PLL input frequency */ #ifdef BOARD_180MHz /* PLL Clock Source: CLKIN * Main Clock Source: PLL * Fout: 220000000 */ # define BOARD_PLL_CLKSEL SYSCON_SYSPLLCLKSEL_CLKIN # define BOARD_PLL_SELI 32 /* Bandwidth select I value */ # define BOARD_PLL_SELP 16 /* Bandwidth select P value */ # define BOARD_PLL_SELR 0 /* Bandwidth select R value */ # define BOARD_PLL_MDEC 8191 /* Encoded M-divider coefficient */ # define BOARD_PLL_NDEC 770 /* Encoded N-divider coefficient */ # define BOARD_PLL_PDEC 98 /* Encoded P-divider coefficient */ # define BOARD_PLL_FOUT 180000000U /* Pll output frequency */ #else /* BOARD_220MHz */ /* PLL Clock Source: FRO 12MHz * Main Clock Source: PLL * Fout: 220000000 */ # define BOARD_PLL_CLKSEL SYSCON_SYSPLLCLKSEL_FFRO # define BOARD_PLL_SELI 34 /* Bandwidth select I value */ # define BOARD_PLL_SELP 31 /* Bandwidth select P value */ # define BOARD_PLL_SELR 0 /* Bandwidth select R value */ # define BOARD_PLL_MDEC 13243 /* Encoded M-divider coefficient */ # define BOARD_PLL_NDEC 1 /* Encoded N-divider coefficient */ # define BOARD_PLL_PDEC 98 /* Encoded P-divider coefficient */ # define BOARD_PLL_FOUT 220000000 /* Pll output frequency */ #endif #define BOARD_MAIN_CLK BOARD_PLL_FOUT /* Main clock frequency */ /* CPU Clock: * * AHB Clock Divider: 1 * AHB Clock Frequency: 180,000,000 or 220,000,000 */ #define BOARD_AHBCLKDIV 1 /* (un-decremented) */ #define BOARD_AHB_FREQUENCY (BOARD_MAIN_CLK / BOARD_AHBCLKDIV) #define BOARD_CPU_FREQUENCY BOARD_AHB_FREQUENCY /* Fraction Rate Generator (FRG) Clock (Optional Flexcomm0 function clock) * * To use the fractional divider, the DIV value must be programmed with the * fixed value of 256. Then: * * Ffrg = (Finput) / (1 + (MULT / DIV)) * * Mainclock is used as the FRG clock source. Divider must be such that the * FRG output frequency is less than equal to 48MHz * * MUL = (Finput - Ffrg) * 256) / Ffrg */ /* Revisit: FRGCLK <= 48MHz cannot be realized with the MainClk source */ #define BOARD FRGCLK_CLKSEL SYSCON_FRGCLKSEL_MAINCLK #define BOARD_FRGCLK_INPUT BOARD_MAIN_CLK /* FRG input frequency */ #define BOARD_FRGCLK 48000000 /* May not be exact */ /* SysTick: The SysTick clock may be clocked internally either by the by the * system clock (CLKSOURCE==1) or by the SysTick function clock (CLKSOURCE==0). * The SysTick Function clock is equal to: * * Fsystick = Fmainclk / SYSTICKCLKDIV * * Tips for selecting BOARD_SYSTICKCLKDIV: The resulting SysTick reload value * should be as large as possible, but must be less than 2^24: * * SYSTICKDIV > Fmainclk / CLK_TCK / 2^24 * * The logic in lpc54_timerisr.c will always select the SysTick function clock * as the source (CLKSOURCE==0). NOTE: When the system tick clock divider is * selected as the clock source, the CPU clock must be at least 2.5 times * faster than the divider output. * * SysTick Divider: (SYSTICKCLKDIV) */ #ifndef CONFIG_SCHED_TICKLESS # if CONFIG_USEC_PER_TICK == 10000 # define BOARD_SYSTICKCLKDIV 1 # else # error Missing SYSTICK divider # endif # define BOARD_SYSTICK_CLOCK (BOARD_AHB_FREQUENCY / BOARD_SYSTICKCLKDIV) #endif /* Flexcomm0: USART0 (REVIST) */ #define BOARD_FLEXCOMM0_CLKSEL SYSCON_FCLKSEL_FRO12M #define BOARD_FLEXCOMM0_FCLK LPC54_FRO_12MHZ /* Flexcomm2: I2C2 (REVIST) */ #define BOARD_FLEXCOMM2_CLKSEL SYSCON_FCLKSEL_FRO12M #define BOARD_FLEXCOMM2_FCLK LPC54_FRO_12MHZ /* EMC */ #ifdef BOARD_220MHz #define BOARD_EMC_CLKDIV 3 /* EMC Clock = CPU FREQ/3 */ #else /* if BOARD_180MHz */ #define BOARD_EMC_CLKDIV 2 /* EMC Clock = CPU FREQ/2 */ #endif #define BOARD_EMC_FREQUENCY (BOARD_CPU_FREQUENCY / BOARD_EMC_CLKDIV) /* SD/MMC or SDIO interface/ /* SD/MMC function clock * * NOTE: The SDIO function clock to the interface can be up to 50 MHZ. * Example: BOARD_MAIN_CLK=220MHz, CLKDIV=5, Finput=44MHz. */ #define BOARD_SDMMC_MAXFREQ 50000000 #define BOARD_SDMMC_CEIL(a,b) (((a) + (b) - 1) / (b)) #define BOARD_SDMMC_CLKSRC SYSCON_SDIOCLKSEL_MAINCLK #define BOARD_SDMMC_CLKDIV BOARD_SDMMC_CEIL(BOARD_MAIN_CLK, BOARD_SDMMC_MAXFREQ) #define BOARD_SDMMC_FREQUENCY (BOARD_MAIN_CLK / BOARD_SDMMC_CLKDIV) /* Mode-dependent function clock division * * Example: BOARD_SDMMC_FREQUENCY=44MHz * BOARD_CLKDIV_INIT=110, Fsdmmc=400KHz (400KHz max) * BOARD_CLKDIV_MMCXFR=4[3], Fsdmmc=11Mhz (20MHz max) See NOTE: * BOARD_CLKDIV_SDWIDEXFR=2, Fsdmmc=22MHz (25MHz max) * BOARD_CLKDIV_SDXFR=2, Fsdmmc=22MHz (25MHz max) * * NOTE: Clock division is 2*n. For example, value of 0 means divide by * 2 * 0 = 0 (no division, bypass), value of 1 means divide by 2 * 1 = 2, value * of 255 means divide by 2 * 255 = 510, and so on. * * SD/MMC logic will write the value ((clkdiv + 1) >> 1) as the divisor. So an * odd value calculated below will be moved up to next higher divider value. So * the value 3 will cause 2 to be written as the divider value and the effective * divider will be 4. */ #define BOARD_CLKDIV_INIT BOARD_SDMMC_CEIL(BOARD_SDMMC_FREQUENCY, 400000) #define BOARD_CLKDIV_MMCXFR BOARD_SDMMC_CEIL(BOARD_SDMMC_FREQUENCY, 20000000) #define BOARD_CLKDIV_SDWIDEXFR BOARD_SDMMC_CEIL(BOARD_SDMMC_FREQUENCY, 25000000) #define BOARD_CLKDIV_SDXFR BOARD_SDMMC_CEIL(BOARD_SDMMC_FREQUENCY, 25000000) /* LED definitions *********************************************************/ /* The LPCXpress-LPC54628 has three user LEDs: D9, D11, and D12. These * LEDs are for application use. They are illuminated when the driving * signal from the LPC546xx is low. The LEDs are driven by ports P2-2 (D9), * P3-3 (D11) and P3-14 (D12). */ /* LED index values for use with board_userled() */ #define BOARD_D9 0 #define BOARD_D11 1 #ifndef CONFIG_ARCH_LEDS # define BOARD_D12 2 # define BOARD_NLEDS 3 #else # define BOARD_NLEDS 2 #endif /* LED bits for use with board_userled_all() */ #define BOARD_D9_BIT (1 << BOARD_D9) #define BOARD_D11_BIT (1 << BOARD_D11) #ifndef CONFIG_ARCH_LEDS # define BOARD_D12_BIT (1 << BOARD_D12) #endif /* These LEDs are not used by the NuttX port unless CONFIG_ARCH_LEDS is * defined. In that case, the usage by the board port is defined in * include/board.h and src/lpc54_autoleds.c. The LEDs are used to encode * OS-related events as follows: */ /* D9 D11 D12 */ #define LED_STARTED 0 /* OFF OFF OFF */ #define LED_HEAPALLOCATE 1 /* ON OFF OFF */ #define LED_IRQSENABLED 2 /* OFF ON OFF */ #define LED_STACKCREATED 3 /* OFF OFF OFF */ #define LED_INIRQ 4 /* NC NC ON (momentary) */ #define LED_SIGNAL 4 /* NC NC ON (momentary) */ #define LED_ASSERTION 4 /* NC NC ON (momentary) */ #define LED_PANIC 4 /* NC NC ON (2Hz flashing) */ #undef LED_IDLE /* Sleep mode indication not supported */ /* After booting, LEDs D9 and D11 are avaible for use by the user. If the * system booted properly, D9 and D11 should be OFF and D12 should be glowing * to indicate that interrupts are occurring. If D12 is flash at 2Hz, then * the system has crashed. */ /* Button definitions *******************************************************/ /* The LPCXpresso has four switches: * * SW2 ISP2 P0.6 * SW3 ISP1 P0.5 * SW4 ISP0 P0.4 * SW5 User Button P1.1 * * In all cased, the signal is low when the button is pressed. * * SW2, SW3, SW4 can be used to force the LPC546xx in to ISP boot modes. * After boot these buttons could be used as user buttons. However, they are * not available when the on-board SRDRAM is used because P0.4, P0.5, and * P0.6 are also used as EMC_D2, EMC_D3, and EMC_D4, respectively. * * So SW5 is really the only button that that is generally available for * software usage. */ #define BUTTON_USER 0 #define NUM_BUTTONS 1 #define BUTTON_USER_BIT (1 << BUTTON_USER) /* Pin Disambiguation *******************************************************/ /* Flexcomm0/USART0 * * USART0 connects to the serial bridge on LPC4322JET100 and is typically used * for the serial console. * * BRIDGE_UART_RXD -> P0_29-ISP_FC0_RXD -> P0.29 GPIO_FC0_RXD_SDA_MOSI_2 * BRIDGE_UART_TXD <- P0_30-ISP_FC0_TXD <- P0.30 GPIO_FC0_TXD_SCL_MISO_2 */ #define GPIO_USART0_RXD (GPIO_FC0_RXD_SDA_MOSI_2 | GPIO_FILTER_OFF) #define GPIO_USART0_TXD (GPIO_FC0_TXD_SCL_MISO_2 | GPIO_FILTER_OFF) /* An alternative for the serial console is a Arduino Uno compatible serial * shield: * * Arduino Uno J13 Board Signal * ----------- ------ ---------------- * D0 RX Pin 15 P3_26-FC4_RXD * D1 TX Pin 13 P3_27-FC4_TXD */ #define GPIO_USART4_RXD (GPIO_FC4_RXD_SDA_MOSI_2 | GPIO_FILTER_OFF) #define GPIO_USART4_TXD (GPIO_FC4_TXD_SCL_MISO_2 | GPIO_FILTER_OFF) /* Flexcomm2/I2C * * For I2C: * Type A & D pins need: * GPIO_OPENDRAIN + GPIO_FILTER_OFF * Type I pins need for Standard mode I2C need: * GPIO_FILTER_OFF + GPIO_I2C_FILTER_ON + GPIO_I2CDRIVE_LOW * Type I pins need for fast speed I2C need: * GPIO_FILTER_OFF + GPIO_I2C_FILTER_ON or OFF + * GPIO_I2CDRIVE_LOW or HIGH * Type I pins need for high speed I2C need: * GPIO_FILTER_OFF + GPIO_I2C_FILTER_OFF + GPIO_I2CDRIVE_HIGH * * There are several on-board devices using I2C2: * * Codec I2C address: 0x1a * Accel I2C address: 0x1d * Touch panel I2C address: 0x38 * * In addition, these same I2C2 pins are brought out through D14 and D15 of * the Arduino Uno connector. */ #if defined(CONFIG_LPC54_I2C_FAST) # define _I2CFILTER GPIO_I2C_FILTER_OFF # define _I2CDRIVE GPIO_I2CDRIVE_HIGH #elif defined(CONFIG_LPC54_I2C_HIGH) # define _I2CFILTER GPIO_I2C_FILTER_OFF # define _I2CDRIVE GPIO_I2CDRIVE_HIGH #else # define _I2CFILTER GPIO_I2C_FILTER_ON # define _I2CDRIVE GPIO_I2CDRIVE_LOW #endif #define GPIO_I2C2_SCL (GPIO_FC2_RTS_SCL_SSEL1_2 | \ GPIO_FILTER_OFF | _I2CFILTER | \ _I2CDRIVE) #define GPIO_I2C2_SDA (GPIO_FC2_CTS_SDA_SSEL0_2 | \ GPIO_FILTER_OFF | _I2CFILTER | \ _I2CDRIVE) /* Flexcomm2/SPI * * There are no SPI devices on board the LPCXpresso-LPC54628. SPI is * available on the Arduino Uno compatible connector, however: * * Arduino Uno J9 Board Signal Pin Type * ----------- ------ ---------------- --------- * D10 SSEL Pin 15 P3_20-FC9_SCK Type D * D11 MOSI Pin 13 P3_21-FC9_MOSI Type A * D12 MISO Pin 11 P3_22-FC9_MISO Type A * D13 SCK Pin 9 P3_30-FC9_SSELn0 Type D * * For SPI: * Type A & D pins need: * GPIO_PUSHPULL (on outputs) + GPIO_SLEW_STANDARD (Type D) + * GPIO_FILTER_OFF * GPIO_SLEW_FAST is optional for high data rates (Type D). * Type I need: * GPIO_I2C_FILTER_OFF + GPIO_I2CDRIVE_LOW + GPIO_FILTER_OFF + * GPIO_I2CSLEW_GPIO */ #define GPIO_FC9_RXD_SDA_MOSI (GPIO_FC9_RXD_SDA_MOSI_1 | \ GPIO_PUSHPULL | GPIO_FILTER_OFF) #define GPIO_FC9_TXD_SCL_MISO (GPIO_FC9_TXD_SCL_MISO_1 | \ GPIO_FILTER_OFF) #define GPIO_FC9_SCK (GPIO_FC9_SCK_1 | GPIO_PUSHPULL | \ GPIO_SLEW_STANDARD | GPIO_FILTER_OFF) /* SD/MMC * * P2_10-SD_CDn * P2_6-SD_D0 * P2_7-SD_D1 * P2_8-SD_D2 * P2_9-SD_D3 * P2_3-SD_CLK * P2_4-SD_CMD * P2_5-SD_POW_EN * P3_15-SD_WPn */ #define GPIO_SD_CARD_DET_N GPIO_SD_CARD_DET_N_2 /* P2.10 */ #define GPIO_SD_D0 GPIO_SD_D0_3 /* P2.6 */ #define GPIO_SD_D1 GPIO_SD_D1_3 /* P2.7 */ #define GPIO_SD_D2 GPIO_SD_D2_3 /* P2.8 */ #define GPIO_SD_D3 GPIO_SD_D3_3 /* P2.9 */ #define GPIO_SD_CLK GPIO_SD_CLK_3 /* P2.3 */ #define GPIO_SD_CMD GPIO_SD_CMD_3 /* P2.4 */ #define GPIO_SD_POW_EN GPIO_SD_POW_EN_2 /* P2.5 */ #define GPIO_SD_WR_PRT GPIO_SD_WR_PRT_2 /* P2.15 */ /* LCD * * There are no alternatives for LCD pins except for the VD0-VD3 pins. * VD0-VD2 are not used in this hardware configuration. VD3 is on * P2.21. */ #define GPIO_LCD_VD3 GPIO_LCD_VD3_1 /* Ethernet Clock * * The Lpcxpresso-LPC546258 uses a LAN8720A PHY in RMII mode. Clocking is * provided via a 25MHz crystal (Y1). CLKOUT on P3.12 is an option if JS4 * is reversed. */ #define BOARD_PHY_CLOCK 25000000 /* 25MHz crystal */ /* Ethernet RMII mode pins: * * P4_16-ENET_MDIO Ethernet MIIM data input and output * P4_15-ENET_MDC Ethernet MIIM clock * * P4_11-ENET_RXD0 Ethernet receive data 0-1 * P4_12-ENET_RXD1 * P4_8-ENET_TXD0 Ethernet transmit data 0-1 * P0_17-ENET_TXD1 * P4_10-ENET_CRS_DV Ethernet receive data valid * P4_13-ENET_TX_EN Ethernet transmit data enable * * P4_14-ENET_RX_CLK REF_CLK, Reference clock * P2_26-ENET_PHY_RSTn nRST (Controlled by board logic) * * NOTE: You must set JP11 and JP12 to close 1-2 to enable Ethernet * port functionality. Some pins are shared with USB0 overcurrent * feature. */ #define GPIO_ENET_MDIO GPIO_ENET_MDIO_2 /* P4.16 */ #define GPIO_ENET_MDC GPIO_ENET_MDC_2 /* P4.15 */ #define GPIO_ENET_RXD0 GPIO_ENET_RXD0_2 /* P4.11 */ #define GPIO_ENET_RXD1 GPIO_ENET_RXD1_2 /* P4.12 */ #define GPIO_ENET_TXD0 GPIO_ENET_TXD0_3 /* P4.8 */ #define GPIO_ENET_TXD1 GPIO_ENET_TXD1_4 /* P0.17 */ #define GPIO_ENET_RX_DV GPIO_ENET_RX_DV_2 /* P4.10 */ #define GPIO_ENET_TX_EN GPIO_ENET_TX_EN_2 /* P4.13 */ #define GPIO_ENET_REF_CLK GPIO_ENET_RX_CLK_2 /* P4.14 */ /**************************************************************************** * Public Types ****************************************************************************/ #ifndef __ASSEMBLY__ /**************************************************************************** * Public Data ****************************************************************************/ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /**************************************************************************** * Public Function Prototypes ****************************************************************************/ #undef EXTERN #if defined(__cplusplus) } #endif #endif /* __ASSEMBLY__ */ #endif /* _CONFIGS_LPCXPRESSO_LPC54628_INCLUDE_BOARD_H */