README ====== This is the README file for the port of NuttX to the Mikroe Clicker2 STM32 board based on the STMicro STM32F407VGT6 MCU. Reference: https://shop.mikroe.com/development-boards/starter/clicker-2/stm32f4 Contents ======== o Serial Console o LEDs o Buttons o Using JTAG o Configurations Serial Console ============== The are no RS-232 drivers on-board. An RS-232 Click board is available: https://shop.mikroe.com/click/interface/rs232 or you can cannot an off- board TTL-to-RS-232 converter as follows: USART2: mikroBUS1 PD6/RX and PD5/TX USART3: mikroBUS2 PD9/RX and PD8TX GND, 3.3V, and 5V. Are also available By default, USART3 on mikroBUS2 is used as the serial console in each configuration unless stated otherwise in the description of the configuration. LEDs ==== The Mikroe Clicker2 STM32 has two user controllable LEDs: LD1/PE12, Active high output illuminates LD2/PE15, Active high output illuminates If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way. If CONFIG_ARCH_LEDs is defined, then NuttX will control the 2 LEDs on board the Clicker2 for STM32. The following definitions describe how NuttX controls the LEDs: SYMBOL Meaning LED state LD1 LD2 ------------------- ----------------------- -------- -------- LED_STARTED NuttX has been started OFF OFF LED_HEAPALLOCATE Heap has been allocated OFF OFF LED_IRQSENABLED Interrupts enabled OFF OFF LED_STACKCREATED Idle stack created ON OFF LED_INIRQ In an interrupt N/C ON LED_SIGNAL In a signal handler No change LED_ASSERTION An assertion failed No change LED_PANIC The system has crashed OFF Blinking LED_IDLE STM32 is is sleep mode Not used Thus is LD1 is illuminated, the Clicker2 has completed boot-up. IF LD2 is glowly softly, then interrupts are being taken; the level of illumination depends amount of time processing interupts. If LD1 is off and LD2 is blinking at about 2Hz, then the system has crashed. Buttons ======= The Mikroe Clicker2 STM32 has two buttons available to software: T2/E0, Low sensed when pressed T3/PA10, Low sensed when pressed Using JTAG ========== The Clicker2 comes with the mikroBootloader installed. That bootloader has not been used and is possibly incompatible with the Clicker2-STM32 linker script at configs/clicker2-stm32/scripts/flash.ld. Often code must be built to execute at an offset in to FLASH when a bootloader is used. Certainly that is the case for the ST-Micro DFU bootloader but I am not aware of the requirements for use with the mikroBootloader. JTAG has been used in the development of this board support. The Clicker2-STM32 board offers a 2x5 JTAG connector. You may use Dupont jumpers to connect this port to JTAG as described here: https://www.mikroe.com/how-to-use-st-link-v2-with-clicker-2-for-stm32-a-detailed-walkthrough/ http://www.playembedded.org/blog/en/2016/02/06/mikroe-clicker-2-for-stm32-and-stlink-v2/ NOTE that the FLASH probably has read protection enabled locked. You may need to follow the instructions at the second link to unlock it. You can also use the STM32 ST-Link CLI tool on Windows to remove the read protection using the -OB command: $ ./ST-LINK_CLI.exe -c SN=53FF6F064966545035320387 SWD LPM STM32 ST-LINK CLI v2.3.0 STM32 ST-LINK Command Line Interface ST-LINK SN : 53FF6F064966545035320387 ST-LINK Firmware version : V2J24S4 Connected via SWD. SWD Frequency = 4000K. Target voltage = 3.2 V. Connection mode : Normal. Debug in Low Power mode enabled. Device ID:0x413 Device family :STM32F40xx/F41xx $ ./ST-LINK_CLI.exe -OB RDP=0 STM32 ST-LINK CLI v2.3.0 STM32 ST-LINK Command Line Interface ST-LINK SN : 53FF6F064966545035320387 ST-LINK Firmware version : V2J24S4 Connected via SWD. SWD Frequency = 4000K. Target voltage = 3.2 V. Connection mode : Normal. Device ID:0x413 Device family :STM32F40xx/F41xx Updating option bytes... Option bytes updated successfully. NOTE: 1. You can get the ST-Link Utilies here: http://www.st.com/en/embedded-software/stsw-link004.html 2. The ST-LINK Utility command line interface is located at: [Install_Directory]\STM32 ST-LINK Utility\ST-LINK Utility\ST-LINK_CLI.exe 3. You can get a summary of all of the command options by running ST-LINK_CLI.exe with no arguments. 4. You can get the serial number of the ST-Link when from the information window if you connect via the ST-Link Utility: 11:04:28 : ST-LINK SN : 53FF6F064966545035320387 11:04:28 : ST-LINK Firmware version : V2J24S4 11:04:28 : Connected via SWD. 11:04:28 : SWD Frequency = 100 KHz. 11:04:28 : Connection mode : Normal. 11:04:28 : Debug in Low Power mode enabled. 11:04:30 : Device ID:0x413 11:04:30 : Device family :STM32F40xx/F41xx 11:04:30 : Can not read memory! Disable Read Out Protection and retry. You can avoid the mess of jumpers using the mikroProg to ST-Link v2 adapter along with a 2x5, 10-wire ribbon cable connector: https://shop.mikroe.com/add-on-boards/adapter/mikroprog-st-link-v2-adapter Then you can use the ST-Link Utility or other debugger software to write the NuttX binary to FLASH. OpenOCD can be used with the ST-Link to provide a debug environment. The debug adaptor is NOT compatible with other JTAG debuggers such as the Segger J-Link. Configurations ============== Information Common to All Configurations ---------------------------------------- Each Clicker2 configuration is maintained in a sub-directory and can be selected as follow: cd tools ./configure.sh clicker2-stm32/ cd - . ./setenv.sh Before sourcing the setenv.sh file above, you should examine it and perform edits as necessary so that TOOLCHAIN_BIN is the correct path to the directory than holds your toolchain binaries. And then build NuttX by simply typing the following. At the conclusion of the make, the nuttx binary will reside in an ELF file called, simply, nuttx. make oldconfig make The that is provided above as an argument to the tools/configure.sh must be is one of the following. NOTES: 1. These configurations use the mconf-based configuration tool. To change any of these configurations using that tool, you should: a. Build and install the kconfig-mconf tool. See nuttx/README.txt see additional README.txt files in the NuttX tools repository. b. Execute 'make menuconfig' in nuttx/ in order to start the reconfiguration process. 2. Unless stated otherwise, all configurations generate console output on USART3, channel 0) as described above under "Serial Console". The relevant configuration settings are listed below: CONFIG_STM32_USART3=y CONFIG_STM32_USART3_SERIALDRIVER=y CONFIG_STM32_USART=y CONFIG_USART3_SERIALDRIVER=y CONFIG_USART3_SERIAL_CONSOLE=y CONFIG_USART3_RXBUFSIZE=256 CONFIG_USART3_TXBUFSIZE=256 CONFIG_USART3_BAUD=115200 CONFIG_USART3_BITS=8 CONFIG_USART3_PARITY=0 CONFIG_USART3_2STOP=0 3. All of these configurations are set up to build under Linux using the "GNU Tools for ARM Embedded Processors" that is maintained by ARM (unless stated otherwise in the description of the configuration). https://launchpad.net/gcc-arm-embedded That toolchain selection can easily be reconfigured using 'make menuconfig'. Here are the relevant current settings: Build Setup: CONFIG_HOST_LINUX =y : Linux environment System Type -> Toolchain: CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIL=y : GNU ARM EABI toolchain Configuration sub-directories ----------------------------- nsh: Configures the NuttShell (nsh) located at examples/nsh. This configuration is focused on low level, command-line driver testing. It has no network. NOTES: 1. Support for NSH built-in applications is provided: Binary Formats: CONFIG_BUILTIN=y : Enable support for built-in programs Application Configuration: CONFIG_NSH_BUILTIN_APPS=y : Enable starting apps from NSH command line No built applications are enabled in the base configuration, however. 2. C++ support for applications is enabled: CONFIG_HAVE_CXX=y CONFIG_HAVE_CXXINITIALIZE=y CONFIG_EXAMPLES_NSH_CXXINITIALIZE=y