/**************************************************************************** * drivers/serial/uart_16550.c * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /* Serial driver for 16550 UART */ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #if defined(CONFIG_16550_UART0_DMA) || defined(CONFIG_16550_UART1_DMA) \ || defined(CONFIG_16550_UART2_DMA) || defined(CONFIG_16550_UART3_DMA) # define HAVE_16550_UART_DMA 1 #endif #ifdef CONFIG_16550_UART /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Timeout for UART Busy Wait, in milliseconds */ #define UART_TIMEOUT_MS 100 /**************************************************************************** * Private Types ****************************************************************************/ struct u16550_s { uart_addrwidth_t uartbase; /* Base address of UART registers */ #ifdef HAVE_16550_UART_DMA int32_t dmatx; FAR struct dma_chan_s *chantx; int32_t dmarx; FAR struct dma_chan_s *chanrx; FAR char *dmarxbuf; size_t dmarxsize; volatile size_t dmarxhead; volatile size_t dmarxtail; int32_t dmarxtimeout; #endif #if !defined(CONFIG_16550_SUPRESS_CONFIG) || defined(HAVE_16550_UART_DMA) uint32_t baud; /* Configured baud */ uint32_t uartclk; /* UART clock frequency */ #endif #ifdef CONFIG_CLK FAR const char *clk_name; /* UART clock name */ FAR struct clk_s *mclk; /* UART clock descriptor */ #endif uart_datawidth_t ier; /* Saved IER value */ uint8_t irq; /* IRQ associated with this UART */ #ifndef CONFIG_16550_SUPRESS_CONFIG uint8_t parity; /* 0=none, 1=odd, 2=even */ uint8_t bits; /* Number of bits (7 or 8) */ bool stopbits2; /* true: Configure with 2 stop bits instead of 1 */ #if defined(CONFIG_SERIAL_IFLOWCONTROL) || defined(CONFIG_SERIAL_OFLOWCONTROL) bool flow; /* flow control (RTS/CTS) enabled */ #endif #endif uart_datawidth_t rxtrigger; /* RX trigger level */ }; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ static int u16550_setup(FAR struct uart_dev_s *dev); static void u16550_shutdown(FAR struct uart_dev_s *dev); static int u16550_attach(FAR struct uart_dev_s *dev); static void u16550_detach(FAR struct uart_dev_s *dev); static int u16550_interrupt(int irq, FAR void *context, FAR void *arg); static int u16550_ioctl(FAR struct file *filep, int cmd, unsigned long arg); static int u16550_receive(FAR struct uart_dev_s *dev, unsigned int *status); static void u16550_rxint(FAR struct uart_dev_s *dev, bool enable); static bool u16550_rxavailable(FAR struct uart_dev_s *dev); #ifdef CONFIG_SERIAL_IFLOWCONTROL static bool u16550_rxflowcontrol(struct uart_dev_s *dev, unsigned int nbuffered, bool upper); #endif #ifdef HAVE_16550_UART_DMA static void u16550_dmasend(FAR struct uart_dev_s *dev); static void u16550_dmatxavail(FAR struct uart_dev_s *dev); static void u16550_dmatxconfig(FAR struct uart_dev_s *dev); static void u16550_dmareceive(FAR struct uart_dev_s *dev); static void u16550_dmarxfree(FAR struct uart_dev_s *dev); static void u16550_dmarxconfig(FAR struct uart_dev_s *dev); #endif static void u16550_send(FAR struct uart_dev_s *dev, int ch); static void u16550_txint(FAR struct uart_dev_s *dev, bool enable); static bool u16550_txready(FAR struct uart_dev_s *dev); static bool u16550_txempty(FAR struct uart_dev_s *dev); /**************************************************************************** * Private Data ****************************************************************************/ static const struct uart_ops_s g_uart_ops = { .setup = u16550_setup, .shutdown = u16550_shutdown, .attach = u16550_attach, .detach = u16550_detach, .ioctl = u16550_ioctl, .receive = u16550_receive, .rxint = u16550_rxint, .rxavailable = u16550_rxavailable, #ifdef CONFIG_SERIAL_IFLOWCONTROL .rxflowcontrol = u16550_rxflowcontrol, #endif #ifdef HAVE_16550_UART_DMA .dmasend = u16550_dmasend, .dmareceive = u16550_dmareceive, .dmarxfree = u16550_dmarxfree, .dmatxavail = u16550_dmatxavail, #endif .send = u16550_send, .txint = u16550_txint, .txready = u16550_txready, .txempty = u16550_txempty, }; /* I/O buffers */ #ifdef CONFIG_16550_UART0 static char g_uart0rxbuffer[CONFIG_16550_UART0_RXBUFSIZE]; static char g_uart0txbuffer[CONFIG_16550_UART0_TXBUFSIZE]; #endif #ifdef CONFIG_16550_UART1 static char g_uart1rxbuffer[CONFIG_16550_UART1_RXBUFSIZE]; static char g_uart1txbuffer[CONFIG_16550_UART1_TXBUFSIZE]; #endif #ifdef CONFIG_16550_UART2 static char g_uart2rxbuffer[CONFIG_16550_UART2_RXBUFSIZE]; static char g_uart2txbuffer[CONFIG_16550_UART2_TXBUFSIZE]; #endif #ifdef CONFIG_16550_UART3 static char g_uart3rxbuffer[CONFIG_16550_UART3_RXBUFSIZE]; static char g_uart3txbuffer[CONFIG_16550_UART3_TXBUFSIZE]; #endif /* DMA receive buffers */ #ifdef CONFIG_16550_UART0_DMA_RXBUFSIZE static char g_uart0dmarxbuf[CONFIG_16550_UART0_DMA_RXBUFSIZE]; #endif #ifdef CONFIG_16550_UART1_DMA_RXBUFSIZE static char g_uart1dmarxbuf[CONFIG_16550_UART1_DMA_RXBUFSIZE]; #endif #ifdef CONFIG_16550_UART2_DMA_RXBUFSIZE static char g_uart2dmarxbuf[CONFIG_16550_UART2_DMA_RXBUFSIZE]; #endif #ifdef CONFIG_16550_UART3_DMA_RXBUFSIZE static char g_uart3dmarxbuf[CONFIG_16550_UART3_DMA_RXBUFSIZE]; #endif /* This describes the state of the 16550 uart0 port. */ #ifdef CONFIG_16550_UART0 static struct u16550_s g_uart0priv = { .uartbase = CONFIG_16550_UART0_BASE, #ifdef CONFIG_16550_UART0_DMA .dmatx = CONFIG_16550_UART0_DMA_TX, .dmarx = CONFIG_16550_UART0_DMA_RX, # if CONFIG_16550_UART0_DMA_RX != -1 .dmarxbuf = g_uart0dmarxbuf, .dmarxsize = CONFIG_16550_UART0_DMA_RXBUFSIZE, .dmarxtimeout = CONFIG_16550_UART0_DMA_RXTIMEOUT, # endif #elif defined(HAVE_16550_UART_DMA) .dmatx = -1, .dmarx = -1, #endif #if !defined(CONFIG_16550_SUPRESS_CONFIG) || defined(CONFIG_16550_UART0_DMA) .baud = CONFIG_16550_UART0_BAUD, .uartclk = CONFIG_16550_UART0_CLOCK, #endif #ifdef CONFIG_CLK .clk_name = CONFIG_16550_UART0_CLOCK_NAME, #endif .irq = CONFIG_16550_UART0_IRQ, #ifndef CONFIG_16550_SUPRESS_CONFIG .parity = CONFIG_16550_UART0_PARITY, .bits = CONFIG_16550_UART0_BITS, .stopbits2 = CONFIG_16550_UART0_2STOP, #if defined(CONFIG_16550_UART0_IFLOWCONTROL) || defined(CONFIG_16550_UART0_OFLOWCONTROL) .flow = true, #endif #endif .rxtrigger = CONFIG_16550_UART0_RX_TRIGGER, }; static uart_dev_t g_uart0port = { .recv = { .size = CONFIG_16550_UART0_RXBUFSIZE, .buffer = g_uart0rxbuffer, }, .xmit = { .size = CONFIG_16550_UART0_TXBUFSIZE, .buffer = g_uart0txbuffer, }, .ops = &g_uart_ops, .priv = &g_uart0priv, }; #endif /* This describes the state of the 16550 uart1 port. */ #ifdef CONFIG_16550_UART1 static struct u16550_s g_uart1priv = { .uartbase = CONFIG_16550_UART1_BASE, #ifdef CONFIG_16550_UART1_DMA .dmatx = CONFIG_16550_UART1_DMA_TX, .dmarx = CONFIG_16550_UART1_DMA_RX, # if CONFIG_16550_UART1_DMA_RX != -1 .dmarxbuf = g_uart1dmarxbuf, .dmarxsize = CONFIG_16550_UART1_DMA_RXBUFSIZE, .dmarxtimeout = CONFIG_16550_UART1_DMA_RXTIMEOUT, # endif #elif defined(HAVE_16550_UART_DMA) .dmatx = -1, .dmarx = -1, #endif #if !defined(CONFIG_16550_SUPRESS_CONFIG) || defined(CONFIG_16550_UART1_DMA) .baud = CONFIG_16550_UART1_BAUD, .uartclk = CONFIG_16550_UART1_CLOCK, #endif #ifdef CONFIG_CLK .clk_name = CONFIG_16550_UART1_CLOCK_NAME, #endif .irq = CONFIG_16550_UART1_IRQ, #ifndef CONFIG_16550_SUPRESS_CONFIG .parity = CONFIG_16550_UART1_PARITY, .bits = CONFIG_16550_UART1_BITS, .stopbits2 = CONFIG_16550_UART1_2STOP, #if defined(CONFIG_16550_UART1_IFLOWCONTROL) || defined(CONFIG_16550_UART1_OFLOWCONTROL) .flow = true, #endif #endif .rxtrigger = CONFIG_16550_UART1_RX_TRIGGER, }; static uart_dev_t g_uart1port = { .recv = { .size = CONFIG_16550_UART1_RXBUFSIZE, .buffer = g_uart1rxbuffer, }, .xmit = { .size = CONFIG_16550_UART1_TXBUFSIZE, .buffer = g_uart1txbuffer, }, .ops = &g_uart_ops, .priv = &g_uart1priv, }; #endif /* This describes the state of the 16550 uart1 port. */ #ifdef CONFIG_16550_UART2 static struct u16550_s g_uart2priv = { .uartbase = CONFIG_16550_UART2_BASE, #ifdef CONFIG_16550_UART2_DMA .dmatx = CONFIG_16550_UART2_DMA_TX, .dmarx = CONFIG_16550_UART2_DMA_RX, # if CONFIG_16550_UART2_DMA_RX != -1 .dmarxbuf = g_uart2dmarxbuf, .dmarxsize = CONFIG_16550_UART2_DMA_RXBUFSIZE, .dmarxtimeout = CONFIG_16550_UART2_DMA_RXTIMEOUT, # endif #elif defined(HAVE_16550_UART_DMA) .dmatx = -1, .dmarx = -1, #endif #if !defined(CONFIG_16550_SUPRESS_CONFIG) || defined(CONFIG_16550_UART2_DMA) .baud = CONFIG_16550_UART2_BAUD, .uartclk = CONFIG_16550_UART2_CLOCK, #endif #ifdef CONFIG_CLK .clk_name = CONFIG_16550_UART2_CLOCK_NAME, #endif .irq = CONFIG_16550_UART2_IRQ, #ifndef CONFIG_16550_SUPRESS_CONFIG .parity = CONFIG_16550_UART2_PARITY, .bits = CONFIG_16550_UART2_BITS, .stopbits2 = CONFIG_16550_UART2_2STOP, #if defined(CONFIG_16550_UART2_IFLOWCONTROL) || defined(CONFIG_16550_UART2_OFLOWCONTROL) .flow = true, #endif #endif .rxtrigger = CONFIG_16550_UART2_RX_TRIGGER, }; static uart_dev_t g_uart2port = { .recv = { .size = CONFIG_16550_UART2_RXBUFSIZE, .buffer = g_uart2rxbuffer, }, .xmit = { .size = CONFIG_16550_UART2_TXBUFSIZE, .buffer = g_uart2txbuffer, }, .ops = &g_uart_ops, .priv = &g_uart2priv, }; #endif /* This describes the state of the 16550 uart1 port. */ #ifdef CONFIG_16550_UART3 static struct u16550_s g_uart3priv = { .uartbase = CONFIG_16550_UART3_BASE, #ifdef CONFIG_16550_UART3_DMA .dmatx = CONFIG_16550_UART3_DMA_TX, .dmarx = CONFIG_16550_UART3_DMA_RX, # if CONFIG_16550_UART3_DMA_RX != -1 .dmarxbuf = g_uart3dmarxbuf, .dmarxsize = CONFIG_16550_UART3_DMA_RXBUFSIZE, .dmarxtimeout = CONFIG_16550_UART3_DMA_RXTIMEOUT, # endif #elif defined(HAVE_16550_UART_DMA) .dmatx = -1, .dmarx = -1, #endif #if !defined(CONFIG_16550_SUPRESS_CONFIG) || defined(CONFIG_16550_UART3_DMA) .baud = CONFIG_16550_UART3_BAUD, .uartclk = CONFIG_16550_UART3_CLOCK, #endif #ifdef CONFIG_CLK .clk_name = CONFIG_16550_UART3_CLOCK_NAME, #endif .irq = CONFIG_16550_UART3_IRQ, #ifndef CONFIG_16550_SUPRESS_CONFIG .parity = CONFIG_16550_UART3_PARITY, .bits = CONFIG_16550_UART3_BITS, .stopbits2 = CONFIG_16550_UART3_2STOP, #if defined(CONFIG_16550_UART3_IFLOWCONTROL) || defined(CONFIG_16550_UART3_OFLOWCONTROL) .flow = true, #endif #endif .rxtrigger = CONFIG_16550_UART3_RX_TRIGGER, }; static uart_dev_t g_uart3port = { .recv = { .size = CONFIG_16550_UART3_RXBUFSIZE, .buffer = g_uart3rxbuffer, }, .xmit = { .size = CONFIG_16550_UART3_TXBUFSIZE, .buffer = g_uart3txbuffer, }, .ops = &g_uart_ops, .priv = &g_uart3priv, }; #endif /* Which UART with be tty0/console and which tty1? tty2? tty3? */ #ifdef CONFIG_16550_SERIAL_DISABLE_REORDERING # if defined(CONFIG_16550_UART0_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart0port /* UART0=console */ # elif defined(CONFIG_16550_UART1_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart1port /* UART1=console */ # elif defined(CONFIG_16550_UART2_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart2port /* UART2=console */ # elif defined(CONFIG_16550_UART3_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart3port /* UART3=console */ # endif # ifdef CONFIG_16550_UART0 # define TTYS0_DEV g_uart0port # endif # ifdef CONFIG_16550_UART1 # define TTYS1_DEV g_uart1port # endif # ifdef CONFIG_16550_UART2 # define TTYS2_DEV g_uart2port # endif # ifdef CONFIG_16550_UART3 # define TTYS3_DEV g_uart3port # endif #else /* CONFIG_16550_SERIAL_DISABLE_REORDERING */ /* Which UART with be tty0/console and which tty1? tty2? tty3? */ # if defined(CONFIG_16550_UART0_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart0port /* UART0=console */ # define TTYS0_DEV g_uart0port /* UART0=ttyS0 */ # ifdef CONFIG_16550_UART1 # define TTYS1_DEV g_uart1port /* UART0=ttyS0;UART1=ttyS1 */ # ifdef CONFIG_16550_UART2 # define TTYS2_DEV g_uart2port /* UART0=ttyS0;UART1=ttyS1;UART2=ttyS2 */ # ifdef CONFIG_16550_UART3 # define TTYS3_DEV g_uart3port /* UART0=ttyS0;UART1=ttyS1;UART2=ttyS2;UART3=ttyS3 */ # else # undef TTYS3_DEV /* UART0=ttyS0;UART1=ttyS1;UART2=ttyS;No ttyS3 */ # endif # else # ifdef CONFIG_16550_UART3 # define TTYS2_DEV g_uart3port /* UART0=ttyS0;UART1=ttyS1;UART3=ttys2;No ttyS3 */ # else # undef TTYS2_DEV /* UART0=ttyS0;UART1=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # endif # else # ifdef CONFIG_16550_UART2 # define TTYS1_DEV g_uart2port /* UART0=ttyS0;UART2=ttyS1;No ttyS3 */ # ifdef CONFIG_16550_UART3 # define TTYS2_DEV g_uart3port /* UART0=ttyS0;UART2=ttyS1;UART3=ttyS2;No ttyS3 */ # else # undef TTYS2_DEV /* UART0=ttyS0;UART2=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # else # ifdef CONFIG_16550_UART3 # define TTYS1_DEV g_uart3port /* UART0=ttyS0;UART3=ttyS1;No ttyS2;No ttyS3 */ # else # undef TTYS1_DEV /* UART0=ttyS0;No ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS2_DEV /* No ttyS2 */ # undef TTYS3_DEV /* No ttyS3 */ # endif # endif # elif defined(CONFIG_16550_UART1_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart1port /* UART1=console */ # define TTYS0_DEV g_uart1port /* UART1=ttyS0 */ # ifdef CONFIG_16550_UART0 # define TTYS1_DEV g_uart0port /* UART1=ttyS0;UART0=ttyS1 */ # ifdef CONFIG_16550_UART2 # define TTYS2_DEV g_uart2port /* UART1=ttyS0;UART0=ttyS1;UART2=ttyS2 */ # ifdef CONFIG_16550_UART3 # define TTYS3_DEV g_uart3port /* UART1=ttyS0;UART0=ttyS1;UART2=ttyS2;UART3=ttyS3 */ # else # undef TTYS3_DEV /* UART1=ttyS0;UART0=ttyS1;UART2=ttyS;No ttyS3 */ # endif # else # ifdef CONFIG_16550_UART3 # define TTYS2_DEV g_uart3port /* UART1=ttyS0;UART0=ttyS1;UART3=ttys2;No ttyS3 */ # else # undef TTYS2_DEV /* UART1=ttyS0;UART0=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # endif # else # ifdef CONFIG_16550_UART2 # define TTYS1_DEV g_uart2port /* UART1=ttyS0;UART2=ttyS1 */ # ifdef CONFIG_16550_UART3 # define TTYS2_DEV g_uart3port /* UART1=ttyS0;UART2=ttyS1;UART3=ttyS2;No ttyS3 */ # else # undef TTYS2_DEV /* UART1=ttyS0;UART2=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # else # ifdef CONFIG_16550_UART3 # define TTYS1_DEV g_uart3port /* UART1=ttyS0;UART3=ttyS1;No ttyS2;No ttyS3 */ # else # undef TTYS1_DEV /* UART1=ttyS0;No ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS2_DEV /* No ttyS2 */ # undef TTYS3_DEV /* No ttyS3 */ # endif # endif # elif defined(CONFIG_16550_UART2_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart2port /* UART2=console */ # define TTYS0_DEV g_uart2port /* UART2=ttyS0 */ # ifdef CONFIG_16550_UART0 # define TTYS1_DEV g_uart0port /* UART2=ttyS0;UART0=ttyS1 */ # ifdef CONFIG_16550_UART1 # define TTYS2_DEV g_uart1port /* UART2=ttyS0;UART0=ttyS1;UART1=ttyS2 */ # ifdef CONFIG_16550_UART3 # define TTYS3_DEV g_uart3port /* UART2=ttyS0;UART0=ttyS1;UART1=ttyS2;UART3=ttyS3 */ # else # undef TTYS3_DEV /* UART2=ttyS0;UART0=ttyS1;UART1=ttyS;No ttyS3 */ # endif # else # ifdef CONFIG_16550_UART3 # define TTYS2_DEV g_uart3port /* UART2=ttyS0;UART0=ttyS1;UART3=ttys2;No ttyS3 */ # else # undef TTYS2_DEV /* UART2=ttyS0;UART0=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # endif # else # ifdef CONFIG_16550_UART1 # define TTYS1_DEV g_uart1port /* UART2=ttyS0;UART1=ttyS1 */ # ifdef CONFIG_16550_UART3 # define TTYS2_DEV g_uart3port /* UART2=ttyS0;UART1=ttyS1;UART3=ttyS2 */ # else # undef TTYS2_DEV /* UART2=ttyS0;UART1=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # else # ifdef CONFIG_16550_UART3 # define TTYS1_DEV g_uart3port /* UART2=ttyS0;UART3=ttyS1;No ttyS3 */ # else # undef TTYS1_DEV /* UART2=ttyS0;No ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS2_DEV /* No ttyS2 */ # undef TTYS3_DEV /* No ttyS3 */ # endif # endif # elif defined(CONFIG_16550_UART3_SERIAL_CONSOLE) # define CONSOLE_DEV g_uart3port /* UART3=console */ # define TTYS0_DEV g_uart3port /* UART3=ttyS0 */ # ifdef CONFIG_16550_UART0 # define TTYS1_DEV g_uart0port /* UART3=ttyS0;UART0=ttyS1 */ # ifdef CONFIG_16550_UART1 # define TTYS2_DEV g_uart1port /* UART3=ttyS0;UART0=ttyS1;UART1=ttyS2 */ # ifdef CONFIG_16550_UART2 # define TTYS3_DEV g_uart2port /* UART3=ttyS0;UART0=ttyS1;UART1=ttyS2;UART2=ttyS3 */ # else # undef TTYS3_DEV /* UART3=ttyS0;UART0=ttyS1;UART1=ttyS;No ttyS3 */ # endif # else # ifdef CONFIG_16550_UART2 # define TTYS2_DEV g_uart2port /* UART3=ttyS0;UART0=ttyS1;UART2=ttys2;No ttyS3 */ # else # undef TTYS2_DEV /* UART3=ttyS0;UART0=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # endif # else # ifdef CONFIG_16550_UART1 # define TTYS1_DEV g_uart1port /* UART3=ttyS0;UART1=ttyS1 */ # ifdef CONFIG_16550_UART2 # define TTYS2_DEV g_uart2port /* UART3=ttyS0;UART1=ttyS1;UART2=ttyS2;No ttyS3 */ # else # undef TTYS2_DEV /* UART3=ttyS0;UART1=ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS3_DEV /* No ttyS3 */ # else # ifdef CONFIG_16550_UART2 # define TTYS1_DEV g_uart2port /* UART3=ttyS0;UART2=ttyS1;No ttyS3;No ttyS3 */ # undef TTYS3_DEV /* UART3=ttyS0;UART2=ttyS1;No ttyS2;No ttyS3 */ # else # undef TTYS1_DEV /* UART3=ttyS0;No ttyS1;No ttyS2;No ttyS3 */ # endif # undef TTYS2_DEV /* No ttyS2 */ # undef TTYS3_DEV /* No ttyS3 */ # endif # endif # endif #endif /* CONFIG_16550_SERIAL_DISABLE_REORDERING */ /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: u16550_serialin ****************************************************************************/ static inline uart_datawidth_t u16550_serialin(FAR struct u16550_s *priv, int offset) { #ifdef CONFIG_SERIAL_UART_ARCH_MMIO return *((FAR volatile uart_datawidth_t *)priv->uartbase + offset); #else return uart_getreg(priv->uartbase, offset); #endif } /**************************************************************************** * Name: u16550_serialout ****************************************************************************/ static inline void u16550_serialout(FAR struct u16550_s *priv, int offset, uart_datawidth_t value) { #ifdef CONFIG_SERIAL_UART_ARCH_MMIO *((FAR volatile uart_datawidth_t *)priv->uartbase + offset) = value; #else uart_putreg(priv->uartbase, offset, value); #endif } #ifdef CONFIG_16550_WAIT_LCR /**************************************************************************** * Name: u16550_wait * * Description: * Wait until UART is not busy. This is needed before writing to LCR. * Otherwise we will get spurious interrupts on Synopsys DesignWare 8250. * * Input Parameters: * priv: UART Struct * * Returned Value: * Zero (OK) on success; ERROR if timeout. * ****************************************************************************/ static int u16550_wait(FAR struct u16550_s *priv) { int i; for (i = 0; i < UART_TIMEOUT_MS; i++) { uint32_t status = u16550_serialin(priv, UART_USR_OFFSET); if ((status & UART_USR_BUSY) == 0) { return OK; } up_mdelay(1); } _err("UART timeout\n"); return ERROR; } #endif /* CONFIG_16550_WAIT_LCR */ /**************************************************************************** * Name: u16550_disableuartint ****************************************************************************/ static inline void u16550_disableuartint(FAR struct u16550_s *priv, FAR uart_datawidth_t *ier) { if (ier) { *ier = priv->ier & UART_IER_ALLIE; } priv->ier &= ~UART_IER_ALLIE; u16550_serialout(priv, UART_IER_OFFSET, priv->ier); } /**************************************************************************** * Name: u16550_enablebreaks ****************************************************************************/ static inline void u16550_enablebreaks(FAR struct u16550_s *priv, bool enable) { uint32_t lcr = u16550_serialin(priv, UART_LCR_OFFSET); if (enable) { lcr |= UART_LCR_BRK; } else { lcr &= ~UART_LCR_BRK; } #ifdef CONFIG_16550_WAIT_LCR /* Wait till UART is not busy before setting LCR */ if (u16550_wait(priv) < 0) { _err("UART wait failed\n"); } #endif /* CONFIG_16550_WAIT_LCR */ u16550_serialout(priv, UART_LCR_OFFSET, lcr); } /**************************************************************************** * Name: u16550_divisor * * Description: * Select a divider to produce the BAUD from the UART_CLK. * * BAUD = UART_CLK / (16 * DL), or * DIV = UART_CLK / BAUD / 16 * * Ignoring the fractional divider for now. * ****************************************************************************/ #ifndef CONFIG_16550_SUPRESS_CONFIG static inline uint32_t u16550_divisor(FAR struct u16550_s *priv) { return (priv->uartclk + (priv->baud << 3)) / (priv->baud << 4); } #endif /**************************************************************************** * Name: u16550_setup * * Description: * Configure the UART baud, bits, parity, fifos, etc. This * method is called the first time that the serial port is * opened. * ****************************************************************************/ static int u16550_setup(FAR struct uart_dev_s *dev) { #ifndef CONFIG_16550_SUPRESS_CONFIG FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; uint16_t div; uint32_t lcr; #if defined(CONFIG_SERIAL_IFLOWCONTROL) || defined(CONFIG_SERIAL_OFLOWCONTROL) uint32_t mcr; #endif /* Clear fifos */ u16550_serialout(priv, UART_FCR_OFFSET, (UART_FCR_RXRST | UART_FCR_TXRST)); /* Set up the IER */ priv->ier = u16550_serialin(priv, UART_IER_OFFSET); /* Set up the LCR */ lcr = 0; switch (priv->bits) { case 5 : lcr |= UART_LCR_WLS_5BIT; break; case 6 : lcr |= UART_LCR_WLS_6BIT; break; case 7 : lcr |= UART_LCR_WLS_7BIT; break; default: case 8 : lcr |= UART_LCR_WLS_8BIT; break; } if (priv->stopbits2) { lcr |= UART_LCR_STB; } if (priv->parity == 1) { lcr |= UART_LCR_PEN; } else if (priv->parity == 2) { lcr |= (UART_LCR_PEN | UART_LCR_EPS); } #ifdef CONFIG_16550_WAIT_LCR /* Wait till UART is not busy before setting LCR */ if (u16550_wait(priv) < 0) { _err("UART wait failed\n"); return ERROR; } #endif /* CONFIG_16550_WAIT_LCR */ /* Enter DLAB=1 */ u16550_serialout(priv, UART_LCR_OFFSET, (lcr | UART_LCR_DLAB)); /* Set the BAUD divisor */ div = u16550_divisor(priv); u16550_serialout(priv, UART_DLM_OFFSET, div >> 8); u16550_serialout(priv, UART_DLL_OFFSET, div & 0xff); #ifdef CONFIG_16550_WAIT_LCR /* Wait till UART is not busy before setting LCR */ if (u16550_wait(priv) < 0) { _err("UART wait failed\n"); return ERROR; } #endif /* CONFIG_16550_WAIT_LCR */ /* Clear DLAB */ u16550_serialout(priv, UART_LCR_OFFSET, lcr); /* Configure the FIFOs */ u16550_serialout(priv, UART_FCR_OFFSET, (priv->rxtrigger << UART_FCR_RXTRIGGER_SHIFT | UART_FCR_TXRST | UART_FCR_RXRST | UART_FCR_FIFOEN)); /* Set up the auto flow control */ #if defined(CONFIG_SERIAL_IFLOWCONTROL) || defined(CONFIG_SERIAL_OFLOWCONTROL) mcr = u16550_serialin(priv, UART_MCR_OFFSET); if (priv->flow) { mcr |= UART_MCR_AFCE; } else { mcr &= ~UART_MCR_AFCE; } mcr |= UART_MCR_RTS; u16550_serialout(priv, UART_MCR_OFFSET, mcr); #endif /* defined(CONFIG_SERIAL_IFLOWCONTROL) || defined(CONFIG_SERIAL_OFLOWCONTROL) */ /* Reconfigure DMA Rx timeout value */ #ifdef HAVE_16550_UART_DMA u16550_dmarxconfig(dev); #endif #endif return OK; } /**************************************************************************** * Name: u16550_shutdown * * Description: * Disable the UART. This method is called when the serial * port is closed * ****************************************************************************/ static void u16550_shutdown(struct uart_dev_s *dev) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; u16550_disableuartint(priv, NULL); } /**************************************************************************** * Name: u16550_attach * * Description: * Configure the UART to operation in interrupt driven mode. This method * is called when the serial port is opened. Normally, this is just after * the setup() method is called, however, the serial console may operate in * a non-interrupt driven mode during the boot phase. * * RX and TX interrupts are not enabled when by the attach method (unless * the hardware supports multiple levels of interrupt enabling). The RX * and TX interrupts are not enabled until the txint() and rxint() methods * are called. * ****************************************************************************/ static int u16550_attach(struct uart_dev_s *dev) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; int ret; #ifdef CONFIG_CLK /* Clk enable */ priv->mclk = clk_get(priv->clk_name); if (priv->mclk) { clk_set_rate(priv->mclk, priv->uartclk); clk_enable(priv->mclk); } #endif /* Attach and enable the IRQ */ ret = irq_attach(priv->irq, u16550_interrupt, dev); #ifndef CONFIG_ARCH_NOINTC if (ret == OK) { /* Enable the interrupt (RX and TX interrupts are still disabled * in the UART */ up_enable_irq(priv->irq); #ifdef HAVE_16550_UART_DMA if (priv->chanrx) { DMA_RESUME(priv->chanrx); } #endif } #endif return ret; } /**************************************************************************** * Name: u16550_detach * * Description: * Detach UART interrupts. This method is called when the serial port is * closed normally just before the shutdown method is called. * The exception is the serial console which is never shutdown. * ****************************************************************************/ static void u16550_detach(FAR struct uart_dev_s *dev) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; #ifdef HAVE_16550_UART_DMA if (priv->chanrx) { DMA_PAUSE(priv->chanrx); } #endif up_disable_irq(priv->irq); irq_detach(priv->irq); #ifdef CONFIG_CLK /* Clk disaable */ if (priv->mclk) { clk_disable(priv->mclk); } #endif } /**************************************************************************** * Name: u16550_interrupt * * Description: * This is the UART interrupt handler. It will be invoked when an * interrupt is received on the 'irq'. It should call uart_xmitchars or * uart_recvchars to perform the appropriate data transfers. The * interrupt handling logic must be able to map the 'arg' to the * appropriate uart_dev_s structure in order to call these functions. * ****************************************************************************/ static int u16550_interrupt(int irq, FAR void *context, FAR void *arg) { FAR struct uart_dev_s *dev = (struct uart_dev_s *)arg; FAR struct u16550_s *priv; uint32_t status; int passes; DEBUGASSERT(dev != NULL && dev->priv != NULL); priv = (FAR struct u16550_s *)dev->priv; /* Loop until there are no characters to be transferred or, * until we have been looping for a long time. */ for (passes = 0; passes < 256; passes++) { /* Get the current UART status and check for loop * termination conditions */ status = u16550_serialin(priv, UART_IIR_OFFSET); /* The UART_IIR_INTSTATUS bit should be zero if there are pending * interrupts */ if ((status & UART_IIR_INTSTATUS) != 0) { /* Break out of the loop when there is no longer a * pending interrupt */ break; } /* Handle the interrupt by its interrupt ID field */ switch (status & UART_IIR_INTID_MASK) { /* Handle incoming, receive bytes (with or without timeout) */ case UART_IIR_INTID_RDA: case UART_IIR_INTID_CTI: { uart_recvchars(dev); break; } /* Handle outgoing, transmit bytes */ case UART_IIR_INTID_THRE: { uart_xmitchars(dev); break; } /* Just clear modem status interrupts (UART1 only) */ case UART_IIR_INTID_MSI: { /* Read the modem status register (MSR) to clear */ status = u16550_serialin(priv, UART_MSR_OFFSET); sinfo("MSR: %02"PRIx32"\n", status); break; } /* Just clear any line status interrupts */ case UART_IIR_INTID_RLS: { /* Read the line status register (LSR) to clear */ status = u16550_serialin(priv, UART_LSR_OFFSET); sinfo("LSR: %02"PRIx32"\n", status); break; } /* There should be no other values */ default: { serr("ERROR: Unexpected IIR: %02"PRIx32"\n", status); break; } } } return OK; } /**************************************************************************** * Name: u16550_ioctl * * Description: * All ioctl calls will be routed through this method * ****************************************************************************/ static int u16550_ioctl(struct file *filep, int cmd, unsigned long arg) { FAR struct inode *inode = filep->f_inode; FAR struct uart_dev_s *dev = inode->i_private; FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; int ret; #ifdef CONFIG_SERIAL_UART_ARCH_IOCTL ret = uart_ioctl(filep, cmd, arg); if (ret != -ENOTTY) { return ret; } #else ret = OK; #endif switch (cmd) { #ifdef CONFIG_SERIAL_TIOCSERGSTRUCT case TIOCSERGSTRUCT: { FAR struct u16550_s *user = (FAR struct u16550_s *)arg; if (!user) { ret = -EINVAL; } else { memcpy(user, dev, sizeof(struct u16550_s)); } } break; #endif case TIOCSBRK: /* BSD compatibility: Turn break on, unconditionally */ { irqstate_t flags = enter_critical_section(); u16550_enablebreaks(priv, true); leave_critical_section(flags); } break; case TIOCCBRK: /* BSD compatibility: Turn break off, unconditionally */ { irqstate_t flags; flags = enter_critical_section(); u16550_enablebreaks(priv, false); leave_critical_section(flags); } break; #if defined(CONFIG_SERIAL_TERMIOS) && !defined(CONFIG_16550_SUPRESS_CONFIG) case TCGETS: { FAR struct termios *termiosp = (FAR struct termios *)arg; irqstate_t flags; if (!termiosp) { ret = -EINVAL; break; } flags = enter_critical_section(); cfsetispeed(termiosp, priv->baud); termiosp->c_cflag = ((priv->parity != 0) ? PARENB : 0) | ((priv->parity == 1) ? PARODD : 0); termiosp->c_cflag |= (priv->stopbits2) ? CSTOPB : 0; #if defined(CONFIG_SERIAL_IFLOWCONTROL) || defined(CONFIG_SERIAL_OFLOWCONTROL) termiosp->c_cflag |= priv->flow ? CRTSCTS : 0; #endif switch (priv->bits) { case 5: termiosp->c_cflag |= CS5; break; case 6: termiosp->c_cflag |= CS6; break; case 7: termiosp->c_cflag |= CS7; break; case 8: default: termiosp->c_cflag |= CS8; break; } leave_critical_section(flags); } break; case TCSETS: { FAR struct termios *termiosp = (FAR struct termios *)arg; irqstate_t flags; if (!termiosp) { ret = -EINVAL; break; } flags = enter_critical_section(); switch (termiosp->c_cflag & CSIZE) { case CS5: priv->bits = 5; break; case CS6: priv->bits = 6; break; case CS7: priv->bits = 7; break; case CS8: default: priv->bits = 8; break; } if ((termiosp->c_cflag & PARENB) != 0) { priv->parity = (termiosp->c_cflag & PARODD) ? 1 : 2; } else { priv->parity = 0; } priv->baud = cfgetispeed(termiosp); priv->stopbits2 = (termiosp->c_cflag & CSTOPB) != 0; #if defined(CONFIG_SERIAL_IFLOWCONTROL) || defined(CONFIG_SERIAL_OFLOWCONTROL) priv->flow = (termiosp->c_cflag & CRTSCTS) != 0; #endif u16550_setup(dev); leave_critical_section(flags); #ifdef CONFIG_CLK /* Clk enable */ priv->mclk = clk_get(priv->clk_name); if (priv->mclk) { clk_set_rate(priv->mclk, priv->uartclk); } #endif } break; #endif default: ret = -ENOTTY; break; } return ret; } /**************************************************************************** * Name: u16550_receive * * Description: * Called (usually) from the interrupt level to receive one * character from the UART. Error bits associated with the * receipt are provided in the return 'status'. * ****************************************************************************/ static int u16550_receive(struct uart_dev_s *dev, unsigned int *status) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; uint32_t rbr; *status = u16550_serialin(priv, UART_LSR_OFFSET); rbr = u16550_serialin(priv, UART_RBR_OFFSET); return rbr; } /**************************************************************************** * Name: u16550_rxint * * Description: * Call to enable or disable RX interrupts * ****************************************************************************/ static void u16550_rxint(struct uart_dev_s *dev, bool enable) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; #ifdef HAVE_16550_UART_DMA if (priv->chanrx) { return; /* Monitor DMA interrupt instead */ } #endif if (enable) { priv->ier |= UART_IER_ERBFI; } else { priv->ier &= ~UART_IER_ERBFI; } u16550_serialout(priv, UART_IER_OFFSET, priv->ier); } /**************************************************************************** * Name: u16550_rxavailable * * Description: * Return true if the receive fifo is not empty * ****************************************************************************/ static bool u16550_rxavailable(struct uart_dev_s *dev) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; return ((u16550_serialin(priv, UART_LSR_OFFSET) & UART_LSR_DR) != 0); } /**************************************************************************** * Name: u16550_dma* * * Description: * Stubbed out DMA-related methods * ****************************************************************************/ #ifdef CONFIG_SERIAL_IFLOWCONTROL static bool u16550_rxflowcontrol(struct uart_dev_s *dev, unsigned int nbuffered, bool upper) { #ifndef CONFIG_16550_SUPRESS_CONFIG FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; if (priv->flow) { #ifdef HAVE_16550_UART_DMA if (priv->chanrx) { /* Pause Rx DMA receive to prevent more data being from * peripheral if the RX buffer is near full. When hardware * RTS is enabled, this will prevent more data from coming * in. Otherwise, Resume Rx DMA to make sure that more * input is received. */ if (upper) { DMA_PAUSE(priv->chanrx); } else { DMA_RESUME(priv->chanrx); } } else #endif { /* Disable Rx interrupt to prevent more data being from * peripheral if the RX buffer is near full. When hardware * RTS is enabled, this will prevent more data from coming * in. Otherwise, enable Rx interrupt to make sure that more * input is received. */ u16550_rxint(dev, !upper); } return true; } #endif return false; } #endif /**************************************************************************** * Name: u16550_dma* * * Description: * Stub functions used when serial DMA is enabled. * ****************************************************************************/ #ifdef HAVE_16550_UART_DMA static void u16550_dmasend_done(FAR struct dma_chan_s *chan, FAR void *arg, ssize_t len) { FAR struct uart_dev_s *dev = arg; if (len > 0) { dev->dmatx.nbytes = len; uart_xmitchars_done(dev); uart_xmitchars_dma(dev); } else /* Fail, resend */ { u16550_dmasend(dev); } } static void u16550_dmasend(FAR struct uart_dev_s *dev) { FAR struct u16550_s *priv = dev->priv; FAR void *buffer = dev->dmatx.buffer; size_t length = dev->dmatx.length; up_clean_dcache((uintptr_t)buffer, (uintptr_t)buffer + length); DMA_START(priv->chantx, u16550_dmasend_done, dev, up_addrenv_va_to_pa((FAR void *)priv->uartbase), up_addrenv_va_to_pa(buffer), length); } static void u16550_dmareceive_done(FAR struct dma_chan_s *chan, FAR void *arg, ssize_t len) { FAR struct uart_dev_s *dev = arg; FAR struct u16550_s *priv = dev->priv; if (len >= 0) { size_t slot = priv->dmarxhead / priv->dmarxsize; size_t offset = priv->dmarxhead - slot * priv->dmarxsize; if (len >= priv->dmarxsize) { len = 0; } if (len < offset) { slot++; /* Wrap, move to the next slot */ } priv->dmarxhead = slot * priv->dmarxsize + len; if (priv->dmarxhead - priv->dmarxtail >= priv->dmarxsize) { serr("The receive dma buffer is overrun\n"); priv->dmarxtail = priv->dmarxhead - priv->dmarxsize / 2; } /* The receive isn't in the process? */ if (dev->dmarx.length == 0) { /* Trigger the receive process */ uart_recvchars_dma(dev); } else { /* Copy the received data */ u16550_dmareceive(dev); } } } static void u16550_dmareceive(FAR struct uart_dev_s *dev) { FAR struct u16550_s *priv = dev->priv; if (priv->dmarxhead != priv->dmarxtail) { size_t length = priv->dmarxhead - priv->dmarxtail; size_t offset = priv->dmarxtail % priv->dmarxsize; FAR char *buffer = priv->dmarxbuf + offset; if (offset + length > priv->dmarxsize) { length = priv->dmarxsize - offset; } if (length > dev->dmarx.length) { length = dev->dmarx.length; } up_invalidate_dcache((uintptr_t)buffer, (uintptr_t)buffer + length); memcpy(dev->dmarx.buffer, buffer, length); dev->dmarx.nbytes = length; priv->dmarxtail += length; uart_recvchars_done(dev); if (priv->dmarxhead != priv->dmarxtail) { /* Trigger the receive process again */ uart_recvchars_dma(dev); } } } static void u16550_dmarxconfig(FAR struct uart_dev_s *dev) { FAR struct u16550_s *priv = dev->priv; struct dma_config_s config; if (priv->chanrx != NULL) { memset(&config, 0, sizeof(config)); config.direction = DMA_DEV_TO_MEM; /* 12bit = 1bit start + 8bit data + 1bit parity + 2bit stop */ config.timeout = 12 * 1000000ull * priv->dmarxtimeout / priv->baud; config.src_width = 1; DMA_CONFIG(priv->chanrx, &config); } } static void u16550_dmarxfree(FAR struct uart_dev_s *dev) { FAR struct u16550_s *priv = dev->priv; if (priv->dmarx == -1) { return; /* Can't receive by DMA */ } if (priv->chanrx == NULL) { priv->chanrx = uart_dmachan(priv->uartbase, priv->dmarx); if (priv->chanrx == NULL) { return; /* Fail to get DMA channel */ } u16550_dmarxconfig(dev); /* Start a never stop DMA cyclic transfer in the background */ DMA_START_CYCLIC(priv->chanrx, u16550_dmareceive_done, dev, up_addrenv_va_to_pa(priv->dmarxbuf), up_addrenv_va_to_pa((FAR void *)priv->uartbase), priv->dmarxsize, priv->dmarxsize / 4); } /* The receive isn't in the process? */ if (dev->dmarx.length == 0) { /* Trigger the receive process */ uart_recvchars_dma(dev); } } static void u16550_dmatxconfig(FAR struct uart_dev_s *dev) { FAR struct u16550_s *priv = dev->priv; struct dma_config_s config; if (priv->chantx != NULL) { memset(&config, 0, sizeof(config)); config.direction = DMA_MEM_TO_DEV; config.dst_width = 1; DMA_CONFIG(priv->chantx, &config); } } static void u16550_dmatxavail(FAR struct uart_dev_s *dev) { FAR struct u16550_s *priv = dev->priv; if (priv->dmatx == -1) { return; /* Can't send by DMA */ } if (priv->chantx == NULL) { priv->chantx = uart_dmachan(priv->uartbase, priv->dmatx); if (priv->chantx == NULL) { return; /* Fail to get DMA channel */ } u16550_dmatxconfig(dev); } /* DMA isn't busy for sending? */ if (dev->dmatx.length == 0) { /* Start DMA for sending */ uart_xmitchars_dma(dev); } } #endif /**************************************************************************** * Name: u16550_send * * Description: * This method will send one byte on the UART * ****************************************************************************/ static void u16550_send(struct uart_dev_s *dev, int ch) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; u16550_serialout(priv, UART_THR_OFFSET, (uart_datawidth_t)ch); } /**************************************************************************** * Name: u16550_txint * * Description: * Call to enable or disable TX interrupts * ****************************************************************************/ static void u16550_txint(struct uart_dev_s *dev, bool enable) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; irqstate_t flags; #ifdef HAVE_16550_UART_DMA if (priv->chantx) { return; /* Monitor DMA interrupt instead */ } #endif flags = enter_critical_section(); if (enable) { priv->ier |= UART_IER_ETBEI; u16550_serialout(priv, UART_IER_OFFSET, priv->ier); /* Fake a TX interrupt here by just calling uart_xmitchars() with * interrupts disabled (note this may recurse). */ uart_xmitchars(dev); } else { priv->ier &= ~UART_IER_ETBEI; u16550_serialout(priv, UART_IER_OFFSET, priv->ier); } leave_critical_section(flags); } /**************************************************************************** * Name: u16550_txready * * Description: * Return true if the tranmsit fifo is not full * ****************************************************************************/ static bool u16550_txready(struct uart_dev_s *dev) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; return ((u16550_serialin(priv, UART_LSR_OFFSET) & UART_LSR_THRE) != 0); } /**************************************************************************** * Name: u16550_txempty * * Description: * Return true if the transmit fifo is empty * ****************************************************************************/ static bool u16550_txempty(struct uart_dev_s *dev) { FAR struct u16550_s *priv = (FAR struct u16550_s *)dev->priv; return ((u16550_serialin(priv, UART_LSR_OFFSET) & UART_LSR_TEMT) != 0); } /**************************************************************************** * Name: u16550_putc * * Description: * Write one character to the UART (polled) * ****************************************************************************/ #ifdef HAVE_16550_CONSOLE static void u16550_putc(FAR struct u16550_s *priv, int ch) { irqstate_t flags; flags = spin_lock_irqsave(NULL); while ((u16550_serialin(priv, UART_LSR_OFFSET) & UART_LSR_THRE) == 0); u16550_serialout(priv, UART_THR_OFFSET, (uart_datawidth_t)ch); spin_unlock_irqrestore(NULL, flags); } #endif /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: u16550_earlyserialinit * * Description: * Performs the low level UART initialization early in debug so that the * serial console will be available during bootup. This must be called * before uart_serialinit. * * NOTE: Configuration of the CONSOLE UART was performed by uart_lowsetup() * very early in the boot sequence. * ****************************************************************************/ void u16550_earlyserialinit(void) { /* Configuration whichever one is the console */ #ifdef CONSOLE_DEV CONSOLE_DEV.isconsole = true; #ifndef CONFIG_16550_SUPRESS_INITIAL_CONFIG u16550_setup(&CONSOLE_DEV); #endif #endif } /**************************************************************************** * Name: u16550_serialinit * * Description: * Register serial console and serial ports. This assumes that * u16550_earlyserialinit was called previously. * ****************************************************************************/ void u16550_serialinit(void) { #ifdef CONSOLE_DEV uart_register("/dev/console", &CONSOLE_DEV); #endif #ifdef TTYS0_DEV uart_register("/dev/ttyS0", &TTYS0_DEV); #endif #ifdef TTYS1_DEV uart_register("/dev/ttyS1", &TTYS1_DEV); #endif #ifdef TTYS2_DEV uart_register("/dev/ttyS2", &TTYS2_DEV); #endif #ifdef TTYS3_DEV uart_register("/dev/ttyS3", &TTYS3_DEV); #endif } /**************************************************************************** * Name: up_putc * * Description: * Provide priority, low-level access to support OS debug writes * ****************************************************************************/ #ifdef HAVE_16550_CONSOLE int up_putc(int ch) { FAR struct u16550_s *priv = (FAR struct u16550_s *)CONSOLE_DEV.priv; /* Check for LF */ if (ch == '\n') { /* Add CR */ u16550_putc(priv, '\r'); } u16550_putc(priv, ch); return ch; } #endif #endif /* CONFIG_16550_UART */