/************************************************************************************ * configs/sam4l-xplained/include/board.h * * Copyright (C) 2013 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ************************************************************************************/ #ifndef __CONFIGS_SAM4L_XPLAINED_INCLUDE_BOARD_H #define __CONFIGS_SAM4L_XPLAINED_INCLUDE_BOARD_H /************************************************************************************ * Included Files ************************************************************************************/ #include #ifndef __ASSEMBLY__ # include # ifdef CONFIG_GPIO_IRQ # include # endif #endif /************************************************************************************ * Definitions ************************************************************************************/ /* Clocking *************************************************************************/ /* Select the DFLL as the source of the system clock. * * Options (define one): * BOARD_SYSCLK_SOURCE_RCSYS - System RC oscillator * BOARD_SYSCLK_SOURCE_OSC0 - Oscillator 0 * BOARD_SYSCLK_SOURCE_PLL0 - Phase Locked Loop 0 * BOARD_SYSCLK_SOURCE_DFLL0 - Digital Frequency Locked Loop * BOARD_SYSCLK_SOURCE_RC80M - 80 MHz RC oscillator * BOARD_SYSCLK_SOURCE_FCFAST12M - 12 MHz RC oscillator * BOARD_SYSCLK_SOURCE_FCFAST8M - 8 MHz RC oscillator * BOARD_SYSCLK_SOURCE_FCFAST4M - 4 MHz RC oscillator * BOARD_SYSCLK_SOURCE_RC1M - 1 MHz RC oscillator */ #define BOARD_SYSCLK_SOURCE_DFLL0 1 /* Nominal frequencies in on-chip RC oscillators. These are *not* configurable * but appear here for use in frequency calculations. NOTE: These may frequencies * may vary with temperature changes. */ #define BOARD_RCSYS_FREQUENCY 115000 /* Nominal frequency of RCSYS (Hz) */ #define BOARD_RC32K_FREQUENCY 32768 /* Nominal frequency of RC32K (Hz) */ #define BOARD_RC80M_FREQUENCY 80000000 /* Nominal frequency of RC80M (Hz) */ #define BOARD_RCFAST4M_FREQUENCY 4000000 /* Nominal frequency of RCFAST4M (Hz) */ #define BOARD_RCFAST8M_FREQUENCY 8000000 /* Nominal frequency of RCFAST8M (Hz) */ #define BOARD_RCFAST12M_FREQUENCY 12000000 /* Nominal frequency of RCFAST12M (Hz) */ #define BOARD_RC1M_FREQUENCY 1000000 /* Nominal frequency of RC1M (Hz) */ /* The SAM4L Xplained Pro has two on-board crystals: * XC100 12MHz OSC0 * XC101 32.768KHz OSC32 */ /* OSC0 Configuration */ #define BOARD_OSC0_FREQUENCY 12000000 /* 12MHz XTAL */ /* OSC32 Configuration */ #define BOARD_OSC32_FREQUENCY 32768 /* 32.768KHz XTAL */ #define BOARD_OSC32_STARTUP_US 6100 #define BOARD_OSC32_SELCURR BSCIF_OSCCTRL32_SELCURR_300 #define BOARD_OSC32_ISXTAL 1 /* OSC32 is a crystal */ /* Digital Frequency Locked Loop configuration * Fdfll = (Fclk * DFLLmul) / DFLLdiv * = 32768 * (48000000/32768) / 1 = 48MHz * * The actual frequency is 47.97MHz due to truncation of the multiplier. * The 48MHz target value is treated as "not-to-exceed" value). Use OSC0 * if you need more accuracy (12MHz with a multiplier of 4). * * DFLL0 source options (select one): * BOARD_DFLL0_SOURCE_RCSYS - System RC oscillator * BOARD_DFLL0_SOURCE_OSC32K - 32.768KHz oscillator * BOARD_DFLL0_SOURCE_OSC0 - Oscillator 0 * BOARD_DFLL0_SOURCE_RC80M - 80 MHz RC oscillator * BOARD_DFLL0_SOURCE_RC32K - 32 kHz RC oscillator * * NOTE: Nothing must be defined if the DFPLL is not used */ #define BOARD_DFLL0_SOURCE_OSC32K 1 #define BOARD_DFLL0_TARGET 48000000 #define BOARD_DFLL0_MUL (BOARD_DFLL0_TARGET / BOARD_OSC32_FREQUENCY) #define BOARD_DFLL0_DIV 1 #define BOARD_DFLL0_FREQUENCY (BOARD_OSC32_FREQUENCY * BOARD_DFLL0_MUL / BOARD_DFLL0_DIV) /* Phase Locked Loop configuration * Fdfll = (Fclk * PLLmul) / PLLdiv * * PLL0 source options (select one): * BOARD_PLL0_SOURCE_OSC0 - Oscillator 0 * BOARD_PLL0_SOURCE_GCLK9 - General clock 9 * * BOARD_GLCK9_SOURCE_RCSYS - System RC oscillator * BOARD_GLCK9_SOURCE_OSC32K - Output from OSC32K * BOARD_GLCK9_SOURCE_DFLL0 - Output from DFLL0 * BOARD_GLCK9_SOURCE_OSC0 - Output from Oscillator0 * BOARD_GLCK9_SOURCE_RC80M - Output from 80MHz RCOSC * BOARD_GLCK9_SOURCE_RCFAST - Output from 4,8,12MHz RCFAST * BOARD_GLCK9_SOURCE_RC1M - Output from 1MHz RC1M * BOARD_GLCK9_SOURCE_CPUCLK - The CPU clock * BOARD_GLCK9_SOURCE_HSBCLK - High Speed Bus clock * BOARD_GLCK9_SOURCE_PBACLK - Peripheral Bus A clock * BOARD_GLCK9_SOURCE_PBBCLK - Peripheral Bus B clock * BOARD_GLCK9_SOURCE_PBCCLK - Peripheral Bus C clock * BOARD_GLCK9_SOURCE_PBDCLK - Peripheral Bus D clock * BOARD_GLCK9_SOURCE_RC32K - Output from 32kHz RCOSC * * NOTE: Nothing must be defined if the PLL0 is not used */ /* System clock dividers: Fbus = Fmck >> BUSshift */ #define BOARD_CPU_SHIFT 0 /* Fcpu = Fmck = 48MHz */ #define BOARD_PBA_SHIFT 0 /* Fpba = Fmck = 48MHz */ #define BOARD_PBB_SHIFT 0 /* Fpbb = Fmck = 48MHz */ #define BOARD_PBC_SHIFT 0 /* Fpbc = Fmck = 48MHz */ #define BOARD_PBD_SHIFT 0 /* Fpbd = Fmck = 48MHz */ /* Resulting frequencies */ #define BOARD_MCK_FREQUENCY (BOARD_DFLL0_FREQUENCY) #define BOARD_CPU_FREQUENCY (BOARD_MCK_FREQUENCY >> BOARD_CPU_SHIFT) #define BOARD_PBA_FREQUENCY (BOARD_MCK_FREQUENCY >> BOARD_PBA_SHIFT) #define BOARD_PBB_FREQUENCY (BOARD_MCK_FREQUENCY >> BOARD_PBB_SHIFT) #define BOARD_PBC_FREQUENCY (BOARD_MCK_FREQUENCY >> BOARD_PBC_SHIFT) #define BOARD_PBD_FREQUENCY (BOARD_MCK_FREQUENCY >> BOARD_PBD_SHIFT) /* USBC. * * "The USBC has two bus clocks connected: One High Speed Bus clock * (CLK_USBC_AHB) and one Peripheral Bus clock (CLK_USBC_APB). These clocks * are generated by the Power Manager. Both clocks are enabled at reset * and can be disabled by the Power Manager. It is recommended to disable * the USBC before disabling the clocks, to avoid freezing the USBC in * an undefined state. * * "To follow the usb data rate at 12Mbit/s in full-speed mode, the * CLK_USBC_AHB clock should be at minimum 12MHz. * * "The 48MHz USB clock is generated by a dedicated generic clock from * the SCIF module. Before using the USB, the user must ensure that the * USB generic clock (GCLK_USBC) is enabled at 48MHz in the SCIF module." * * USB Generic Clock 7 (GCLK_USBC) source selection (one only) * * BOARD_USBC_SRC_OSC0 * BOARD_USBC_SRC_PLL0 * BOARD_USBC_SRC_DFLL * BOARD_USBC_SRC_GCLKIN0 */ #define BOARD_USBC_SRC_DFLL 1 /* Source DFLL0 at 48MHz */ #define BOARD_USBC_GCLK_DIV 1 /* Fusb = Fdfll / 1 = 48MHz */ /* LED definitions ******************************************************************/ /* There are three LEDs on board the SAM4L Xplained Pro board: The EDBG * controls two of the LEDs, a power LED and a status LED. There is only * one user controllable LED, a yellow LED labeled LED0 near the SAM4L USB * connector. * * This LED is controlled by PC07 and LED0 can be activated by driving the * PC07 to GND. */ /* LED index values for use with sam_setled() */ #define BOARD_LED0 0 #define BOARD_NLEDS 1 /* LED bits for use with sam_setleds() */ #define BOARD_LED0_BIT (1 << BOARD_LED0) /* When CONFIG_ARCH_LEDS is defined in the NuttX configuration, NuttX will * control LED0 as defined below. Thus if LED0 is statically on, NuttX has * successfully booted and is, apparently, running normmally. If LED0 is * flashing at approximately 2Hz, then a fatal error has been detected and the * system has halted. */ #define LED_STARTED 0 /* LED0=OFF */ #define LED_HEAPALLOCATE 0 /* LED0=OFF */ #define LED_IRQSENABLED 0 /* LED0=OFF */ #define LED_STACKCREATED 1 /* LED0=ON */ #define LED_INIRQ 2 /* LED0=no change */ #define LED_SIGNAL 2 /* LED0=no change */ #define LED_ASSERTION 2 /* LED0=no change */ #define LED_PANIC 3 /* LED0=flashing */ /* Button definitions ***************************************************************/ /* QTouch button: The SAM4L Xplained Pro kit has one QTouch button. The connection * to the SAM4L is: * * PC13 CATB_SENSE15 * PC14 CATB_DIS */ /* Mechanical buttons: * * The SAM4L Xplained Pro contains two mechanical buttons. One button is the * RESET button connected to the SAM4L reset line and the other is a generic user * configurable button. When a button is pressed it will drive the I/O line to GND. * * PC24 SW0 */ /* The STM32F4 Discovery supports one button: */ #define BUTTON_SW0 0 #define NUM_BUTTONS 1 #define BUTTON_SW0_BIT (1 << BUTTON_SW0) /* Alternate Function Disambiguation ************************************************/ /* USART0 is also available on connectors EXT1 and EXT4: * * EXT1 TXT4 GPIO Function * ---- ---- ------ ----------- * 13 13 PB00 USART0_RXD * 14 14 PB01 USART0_TXD */ #define GPIO_USART0_RXD GPIO_USART0_RXD_4 #define GPIO_USART0_TXD GPIO_USART0_TXD_4 /* The SAM4L Xplained Pro contains an Embedded Debugger (EDBG) that can be used to * program and debug the ATSAM4LC4C using Serial Wire Debug (SWD). The Embedded * debugger also include a Virtual Com port interface over USART1. Virtual COM * port connections: * * PC26 USART1 RXD * PC27 USART1 TXD */ #define GPIO_USART1_RXD GPIO_USART1_RXD_2 #define GPIO_USART1_TXD GPIO_USART1_TXD_2 /* SPI pins are brought out on EXT1 and EXT2 as: * * PA22 SPI/MOSI * PA21 SPI/MISO * PC30 SPI/SCK */ #define GPIO_SPI0_MISO GPIO_SPI0_MISO_1 #define GPIO_SPI0_MOSI GPIO_SPI0_MOSI_1 #define GPIO_SPI0_SPCK GPIO_SPI0_SPCK_4 /************************************************************************************ * Public Data ************************************************************************************/ #ifndef __ASSEMBLY__ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /************************************************************************************ * Public Function Prototypes ************************************************************************************/ /************************************************************************************ * Name: sam_boardinitialize * * Description: * All SAM3U architectures must provide the following entry point. This entry point * is called early in the intitialization -- after all memory has been configured * and mapped but before any devices have been initialized. * ************************************************************************************/ void sam_boardinitialize(void); /************************************************************************************ * Name: sam_ledinit, sam_setled, and sam_setleds * * Description: * If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board LEDs. If * CONFIG_ARCH_LEDS is not defined, then the following interfaces are available to * control the LEDs from user applications. * ************************************************************************************/ #ifndef CONFIG_ARCH_LEDS void sam_ledinit(void); void sam_setled(int led, bool ledon); void sam_setleds(uint8_t ledset); #endif /************************************************************************************ * Name: up_buttoninit * * Description: * up_buttoninit() must be called to initialize button resources. After that, * up_buttons() may be called to collect the current state of all buttons or * up_irqbutton() may be called to register button interrupt handlers. * ************************************************************************************/ #ifdef CONFIG_ARCH_BUTTONS void up_buttoninit(void); /************************************************************************************ * Name: up_buttons * * Description: * After up_buttoninit() has been called, up_buttons() may be called to collect * the state of all buttons. up_buttons() returns an 8-bit bit set with each bit * associated with a button. See the BUTTON* definitions above for the meaning of * each bit in the returned value. * ************************************************************************************/ uint8_t up_buttons(void); /************************************************************************************ * Name: up_irqbutton * * Description: * This function may be called to register an interrupt handler that will be * called when a button is depressed or released. The ID value is one of the * BUTTON* definitions provided above. The previous interrupt handler address is * returned (so that it may restored, if so desired). * ************************************************************************************/ #ifdef CONFIG_GPIOA_IRQ xcpt_t up_irqbutton(int id, xcpt_t irqhandler); #endif #endif /* CONFIG_ARCH_BUTTONS */ #undef EXTERN #if defined(__cplusplus) } #endif #endif /* __ASSEMBLY__ */ #endif /* __CONFIGS_SAM4L_XPLAINED_INCLUDE_BOARD_H */