/**************************************************************************** * boards/arm/stm32/shenzhou/include/board.h * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ #ifndef __BOARDS_ARM_STM32_SHENZHOU_INCLUDE_BOARD_H #define __BOARDS_ARM_STM32_SHENZHOU_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif #include "stm32_rcc.h" #include "stm32_sdio.h" #include "stm32.h" #include /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Clocking *****************************************************************/ /* HSI - 8 MHz RC factory-trimmed * LSI - 40 KHz RC (30-60KHz, uncalibrated) * HSE - On-board crystal frequency is 25MHz * LSE - 32.768 kHz */ #define STM32_BOARD_XTAL 25000000ul #define STM32_HSI_FREQUENCY 8000000ul #define STM32_LSI_FREQUENCY 40000 #define STM32_HSE_FREQUENCY STM32_BOARD_XTAL #define STM32_LSE_FREQUENCY 32768 /* PLL output is 72MHz */ #define STM32_PLL_PREDIV2 RCC_CFGR2_PREDIV2d5 /* 25MHz / 5 => 5MHz */ #define STM32_PLL_PLL2MUL RCC_CFGR2_PLL2MULx8 /* 5MHz * 8 => 40MHz */ #define STM32_PLL_PREDIV1 RCC_CFGR2_PREDIV1d5 /* 40MHz / 5 => 8MHz */ #define STM32_PLL_PLLMUL RCC_CFGR_PLLMUL_CLKx9 /* 8MHz * 9 => 72Mhz */ #define STM32_PLL_FREQUENCY (72000000) /* SYCLLK and HCLK are the PLL frequency */ #define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY #define STM32_HCLK_FREQUENCY STM32_PLL_FREQUENCY #define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */ /* APB2 clock (PCLK2) is HCLK (72MHz) */ #define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK #define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY #define STM32_APB2_CLKIN (STM32_PCLK2_FREQUENCY) /* Timers 2-7, 12-14 */ /* APB2 timers 1 and 8 will receive PCLK2. */ #define STM32_APB2_TIM1_CLKIN (STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM8_CLKIN (STM32_PCLK2_FREQUENCY) /* APB1 clock (PCLK1) is HCLK/2 (36MHz) */ #define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2 #define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2) /* APB1 timers 2-7 will be twice PCLK1 */ #define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY) /* MCO output driven by PLL3. * From above, we already have PLL3 input frequency as: * * STM32_PLL_PREDIV2 = 5, 25MHz / 5 => 5MHz */ #if defined(CONFIG_STM32_MII_MCO) || defined(CONFIG_STM32_RMII_MCO) # define BOARD_CFGR_MCO_SOURCE RCC_CFGR_PLL3CLK /* Source: PLL3 */ # define STM32_PLL_PLL3MUL RCC_CFGR2_PLL3MULx10 /* MCO 5MHz * 10 = 50MHz */ #endif /* LED definitions **********************************************************/ /* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in * any way. The following definitions are used to access individual LEDs. */ /* LED index values for use with board_userled() */ #define BOARD_LED1 0 #define BOARD_LED2 1 #define BOARD_LED3 2 #define BOARD_LED4 3 #define BOARD_NLEDS 4 /* LED bits for use with board_userled_all() */ #define BOARD_LED1_BIT (1 << BOARD_LED1) #define BOARD_LED2_BIT (1 << BOARD_LED2) #define BOARD_LED3_BIT (1 << BOARD_LED3) #define BOARD_LED4_BIT (1 << BOARD_LED4) /* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 4 LEDs on * board the STM3240G-EVAL. * The following definitions describe how NuttX controls the LEDs: */ #define LED_STARTED 0 /* LED1 */ #define LED_HEAPALLOCATE 1 /* LED2 */ #define LED_IRQSENABLED 2 /* LED1 + LED2 */ #define LED_STACKCREATED 3 /* LED3 */ #define LED_INIRQ 4 /* LED1 + LED3 */ #define LED_SIGNAL 5 /* LED2 + LED3 */ #define LED_ASSERTION 6 /* LED1 + LED2 + LED3 */ #define LED_PANIC 7 /* N/C + N/C + N/C + LED4 */ /* Button definitions *******************************************************/ /* The STM3240G-EVAL supports three buttons: */ #define BUTTON_KEY1 0 /* Name printed on board */ #define BUTTON_KEY2 1 #define BUTTON_KEY3 2 #define BUTTON_KEY4 3 #define NUM_BUTTONS 4 #define BUTTON_USERKEY2 BUTTON_KEY1 /* Names in schematic */ #define BUTTON_USERKEY BUTTON_KEY2 #define BUTTON_TAMPER BUTTON_KEY3 #define BUTTON_WAKEUP BUTTON_KEY4 #define BUTTON_KEY1_BIT (1 << BUTTON_KEY1) #define BUTTON_KEY2_BIT (1 << BUTTON_KEY2) #define BUTTON_KEY3_BIT (1 << BUTTON_KEY3) #define BUTTON_KEY4_BIT (1 << BUTTON_KEY4) #define BUTTON_USERKEY2_BIT BUTTON_KEY1_BIT #define BUTTON_USERKEY_BIT BUTTON_KEY2_BIT #define BUTTON_TAMPER_BIT BUTTON_KEY3_BIT #define BUTTON_WAKEUP_BIT BUTTON_KEY4_BIT /* Relays */ #define NUM_RELAYS 2 /* Pin selections ***********************************************************/ /* Ethernet * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 24 PA1 MII_RX_CLK Ethernet PHY NOTE: Despite the MII labeling of * RMII_REF_CLK Ethernet PHY these signals, the DM916AEP is * 25 PA2 MII_MDIO Ethernet PHY actually configured to work in RMII * 48 PB11 MII_TX_EN Ethernet PHY mode. * 51 PB12 MII_TXD0 Ethernet PHY * 52 PB13 MII_TXD1 Ethernet PHY * 16 PC1 MII_MDC Ethernet PHY * 34 PC5 MII_INT Ethernet PHY * 55 PD8 MII_RX_DV Ethernet PHY. Requires CONFIG_STM32_ETH_REMAP * 55 PD8 RMII_CRSDV Ethernet PHY. Requires CONFIG_STM32_ETH_REMAP * 56 PD9 MII_RXD0 Ethernet PHY. Requires CONFIG_STM32_ETH_REMAP * 57 PD10 MII_RXD1 Ethernet PHY. Requires CONFIG_STM32_ETH_REMAP * * The board desdign can support a 50MHz external clock to drive the PHY * (U9). However, on my board, U9 is not present. * * 67 PA8 MCO DM9161AEP */ #ifdef CONFIG_STM32_ETHMAC # ifndef CONFIG_STM32_ETH_REMAP # error "STM32 Ethernet requires CONFIG_STM32_ETH_REMAP" # endif # ifndef CONFIG_STM32_RMII # error "STM32 Ethernet requires CONFIG_STM32_RMII" # endif # ifndef CONFIG_STM32_RMII_MCO # error "STM32 Ethernet requires CONFIG_STM32_RMII_MCO" # endif #endif /* USB * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 68 PA9 USB_VBUS MINI-USB-AB. JP3 * 69 PA10 USB_ID MINI-USB-AB. JP5 * 70 PA11 USB_DM MINI-USB-AB * 71 PA12 USB_DP MINI-USB-AB * 95 PB8 USB_PWR Drives USB VBUS */ /* UARTS/USARTS * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 68 PA9 USART1_TX MAX3232 to CN5. Requires CONFIG_STM32_USART1_REMAP * 69 PA10 USART1_RX MAX3232 to CN5. Requires CONFIG_STM32_USART1_REMAP * 86 PD5 USART2_TX MAX3232 to CN6. Requires CONFIG_STM32_USART2_REMAP * 87 PD6 USART2_RX MAX3232 to CN6. Requires CONFIG_STM32_USART2_REMAP * 86 PD5 485_TX Same as USART2_TX but goes to SP3485 * 87 PD6 485_RX Save as USART2_RX but goes to SP3485 (see JP4) */ #if defined(CONFIG_STM32_USART1) && !defined(CONFIG_STM32_USART1_REMAP) # error "CONFIG_STM32_USART1 requires CONFIG_STM32_USART1_REMAP" #endif #if defined(CONFIG_STM32_USART2) && !defined(CONFIG_STM32_USART2_REMAP) # error "CONFIG_STM32_USART2 requires CONFIG_STM32_USART2_REMAP" #endif /* SPI * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 30 PA5 SPI1_SCK To the SD card, SPI FLASH. * Requires !CONFIG_STM32_SPI1_REMAP * 31 PA6 SPI1_MISO To the SD card, SPI FLASH. * Requires !CONFIG_STM32_SPI1_REMAP * 32 PA7 SPI1_MOSI To the SD card, SPI FLASH. * Requires !CONFIG_STM32_SPI1_REMAP * 78 PC10 SPI3_SCK To TFT LCD (CN13), * the NRF24L01 2.4G wireless module. * Requires CONFIG_STM32_SPI3_REMAP. * 79 PC11 SPI3_MISO To TFT LCD (CN13), * the NRF24L01 2.4G wireless module. * Requires CONFIG_STM32_SPI3_REMAP. * 80 PC12 SPI3_MOSI To TFT LCD (CN13), * the NRF24L01 2.4G wireless module. * Requires CONFIG_STM32_SPI3_REMAP. */ #if defined(CONFIG_STM32_SPI1) && defined(CONFIG_STM32_SPI1_REMAP) # error "CONFIG_STM32_SPI1 must not have CONFIG_STM32_SPI1_REMAP" #endif #if defined(CONFIG_STM32_SPI3) && !defined(CONFIG_STM32_SPI3_REMAP) # error "CONFIG_STM32_SPI3 requires CONFIG_STM32_SPI3_REMAP" #endif /* DAC * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 29 PA4 DAC_OUT1 To CON5(CN14) * 30 PA5 DAC_OUT2 To CON5(CN14). JP10 */ /* ADC * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 35 PB0 ADC_IN1 GPIO_ADC12_IN8. To CON5(CN14) * 36 PB1 ADC_IN2 GPIO_ADC12_IN9. To CON5(CN14) * 15 PC0 POTENTIO_METER GPIO_ADC12_IN10 */ /* CAN * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 91 PB5 CAN2_RX Requires CONFIG_STM32_CAN2_REMAP. * 92 PB6 CAN2_TX Requires CONFIG_STM32_CAN2_REMAP. See also JP11 * 81 PD0 CAN1_RX Requires CONFIG_STM32_CAN1_REMAP2. * 82 PD1 CAN1_TX Requires CONFIG_STM32_CAN1_REMAP2. */ #if defined(CONFIG_STM32_CAN1) && !defined(CONFIG_STM32_CAN1_REMAP2) # error "CONFIG_STM32_CAN1 requires CONFIG_STM32_CAN1_REMAP2" #endif #if defined(CONFIG_STM32_CAN2) && !defined(CONFIG_STM32_CAN2_REMAP) # error "CONFIG_STM32_CAN2 requires CONFIG_STM32_CAN2_REMAP" #endif /* I2C * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 92 PB6 I2C1_SCL Requires !CONFIG_STM32_I2C1_REMAP * 93 PB7 I2C1_SDA */ #if defined(CONFIG_STM32_I2C1) && defined(CONFIG_STM32_I2C1_REMAP) # error "CONFIG_STM32_I2C1 must not have CONFIG_STM32_I2C1_REMAP" #endif /* I2S * * -- ---- -------------- --------------------------------------------------- * PN NAME SIGNAL NOTES * -- ---- -------------- --------------------------------------------------- * 51 PB12 I2S_WS GPIO_I2S2_WS. Audio DAC * 52 PB13 I2S_CK GPIO_I2S2_CK. Audio DAC * 54 PB15 I2S_DIN ??? Audio DAC data in. * 63 PC6 I2S_MCK GPIO_I2S2_MCK. Audio DAC. Active low: Pulled high */ /**************************************************************************** * Public Data ****************************************************************************/ #ifndef __ASSEMBLY__ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /**************************************************************************** * Public Function Prototypes ****************************************************************************/ /**************************************************************************** * Name: stm32_lcdclear * * Description: * This is a non-standard LCD interface just for the Shenzhou board. * Because of the various rotations, clearing the display in the normal way * by writing a sequences of runs that covers the entire display can be * very slow. Here the display is cleared by simply setting all GRAM * memory to the specified color. * ****************************************************************************/ void stm32_lcdclear(uint16_t color); /**************************************************************************** * Relay control functions * * Description: * Non-standard functions for relay control from the Shenzhou board. * * NOTE: These must match the prototypes in include/nuttx/arch.h * ****************************************************************************/ #ifdef CONFIG_ARCH_RELAYS void up_relaysinit(void); void relays_setstat(int relays, bool stat); bool relays_getstat(int relays); void relays_setstats(uint32_t relays_stat); uint32_t relays_getstats(void); void relays_onoff(int relays, uint32_t mdelay); void relays_onoffs(uint32_t relays_stat, uint32_t mdelay); void relays_resetmode(int relays); void relays_powermode(int relays); void relays_resetmodes(uint32_t relays_stat); void relays_powermodes(uint32_t relays_stat); #endif /**************************************************************************** * Chip ID functions * * Description: * Non-standard functions to obtain chip ID information. * ****************************************************************************/ const char *stm32_getchipid(void); const char *stm32_getchipid_string(void); #undef EXTERN #if defined(__cplusplus) } #endif #endif /* __ASSEMBLY__ */ #endif /* __BOARDS_ARM_STM32_SHENZHOU_INCLUDE_BOARD_H */