/**************************************************************************** * drivers/audio/cs43l22.c * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "cs43l22.h" /**************************************************************************** * Private Function Prototypes ****************************************************************************/ #if !defined(CONFIG_CS43L22_REGDUMP) && !defined(CONFIG_CS43L22_CLKDEBUG) static #endif uint8_t cs43l22_readreg(FAR struct cs43l22_dev_s *priv, uint8_t regaddr); static void cs43l22_writereg(FAR struct cs43l22_dev_s *priv, uint8_t regaddr, uint8_t regval); #ifndef CONFIG_AUDIO_EXCLUDE_VOLUME static void cs43l22_setvolume(FAR struct cs43l22_dev_s *priv, uint16_t volume, bool mute); #endif #ifndef CONFIG_AUDIO_EXCLUDE_TONE static void cs43l22_setbass(FAR struct cs43l22_dev_s *priv, uint8_t bass); static void cs43l22_settreble(FAR struct cs43l22_dev_s *priv, uint8_t treble); #endif static void cs43l22_setdatawidth(FAR struct cs43l22_dev_s *priv); static void cs43l22_setbitrate(FAR struct cs43l22_dev_s *priv); /* Audio lower half methods (and close friends) */ static int cs43l22_getcaps(FAR struct audio_lowerhalf_s *dev, int type, FAR struct audio_caps_s *caps); #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_configure(FAR struct audio_lowerhalf_s *dev, FAR void *session, FAR const struct audio_caps_s *caps); #else static int cs43l22_configure(FAR struct audio_lowerhalf_s *dev, FAR const struct audio_caps_s *caps); #endif static int cs43l22_shutdown(FAR struct audio_lowerhalf_s *dev); static void cs43l22_senddone(FAR struct i2s_dev_s *i2s, FAR struct ap_buffer_s *apb, FAR void *arg, int result); static void cs43l22_returnbuffers(FAR struct cs43l22_dev_s *priv); static int cs43l22_sendbuffer(FAR struct cs43l22_dev_s *priv); #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_start(FAR struct audio_lowerhalf_s *dev, FAR void *session); #else static int cs43l22_start(FAR struct audio_lowerhalf_s *dev); #endif #ifndef CONFIG_AUDIO_EXCLUDE_STOP #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_stop(FAR struct audio_lowerhalf_s *dev, FAR void *session); #else static int cs43l22_stop(FAR struct audio_lowerhalf_s *dev); #endif #endif #ifndef CONFIG_AUDIO_EXCLUDE_PAUSE_RESUME #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_pause(FAR struct audio_lowerhalf_s *dev, FAR void *session); static int cs43l22_resume(FAR struct audio_lowerhalf_s *dev, FAR void *session); #else static int cs43l22_pause(FAR struct audio_lowerhalf_s *dev); static int cs43l22_resume(FAR struct audio_lowerhalf_s *dev); #endif #endif static int cs43l22_enqueuebuffer(FAR struct audio_lowerhalf_s *dev, FAR struct ap_buffer_s *apb); static int cs43l22_cancelbuffer(FAR struct audio_lowerhalf_s *dev, FAR struct ap_buffer_s *apb); static int cs43l22_ioctl(FAR struct audio_lowerhalf_s *dev, int cmd, unsigned long arg); #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_reserve(FAR struct audio_lowerhalf_s *dev, FAR void **session); #else static int cs43l22_reserve(FAR struct audio_lowerhalf_s *dev); #endif #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_release(FAR struct audio_lowerhalf_s *dev, FAR void *session); #else static int cs43l22_release(FAR struct audio_lowerhalf_s *dev); #endif /* Interrupt handling an worker thread */ #ifdef CS43L22_USE_FFLOCK_INT static void cs43l22_interrupt_work(FAR void *arg); static int cs43l22_interrupt(FAR const struct cs43l22_lower_s *lower, FAR void *arg); #endif static void *cs43l22_workerthread(pthread_addr_t pvarg); /* Initialization */ static void cs43l22_audio_output(FAR struct cs43l22_dev_s *priv); #if 0 /* Not used */ static void cs43l22_audio_input(FAR struct cs43l22_dev_s *priv); #endif #ifdef CS43L22_USE_FFLOCK_INT static void cs43l22_configure_ints(FAR struct cs43l22_dev_s *priv); #else # define cs43l22_configure_ints(p) #endif static void cs43l22_reset(FAR struct cs43l22_dev_s *priv); /**************************************************************************** * Private Data ****************************************************************************/ static const struct audio_ops_s g_audioops = { cs43l22_getcaps, /* getcaps */ cs43l22_configure, /* configure */ cs43l22_shutdown, /* shutdown */ cs43l22_start, /* start */ #ifndef CONFIG_AUDIO_EXCLUDE_STOP cs43l22_stop, /* stop */ #endif #ifndef CONFIG_AUDIO_EXCLUDE_PAUSE_RESUME cs43l22_pause, /* pause */ cs43l22_resume, /* resume */ #endif NULL, /* allocbuffer */ NULL, /* freebuffer */ cs43l22_enqueuebuffer, /* enqueue_buffer */ cs43l22_cancelbuffer, /* cancel_buffer */ cs43l22_ioctl, /* ioctl */ NULL, /* read */ NULL, /* write */ cs43l22_reserve, /* reserve */ cs43l22_release /* release */ }; /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: cs43l22_readreg * * Description: * Read the specified 16-bit register from the CS43L22 device. * ****************************************************************************/ #if !defined(CONFIG_CS43L22_REGDUMP) && !defined(CONFIG_CS43L22_CLKDEBUG) static #endif uint8_t cs43l22_readreg(FAR struct cs43l22_dev_s *priv, uint8_t regaddr) { int retries; /* Try up to three times to read the register */ for (retries = 1; retries <= 3; retries++) { struct i2c_msg_s msg[2]; uint8_t data; int ret; /* Set up to write the address */ msg[0].frequency = priv->lower->frequency; msg[0].addr = priv->lower->address; msg[0].flags = 0; msg[0].buffer = ®addr; msg[0].length = 1; /* Followed by the read data */ msg[1].frequency = priv->lower->frequency; msg[1].addr = priv->lower->address; msg[1].flags = I2C_M_READ; msg[1].buffer = &data; msg[1].length = 12; /* Read the register data. The returned value is the number messages * completed. */ ret = I2C_TRANSFER(priv->i2c, msg, 2); if (ret < 0) { #ifdef CONFIG_I2C_RESET /* Perhaps the I2C bus is locked up? Try to shake the bus free */ audwarn("WARNING: I2C_TRANSFER failed: %d ... Resetting\n", ret); ret = I2C_RESET(priv->i2c); if (ret < 0) { auderr("ERROR: I2C_RESET failed: %d\n", ret); break; } #else auderr("ERROR: I2C_TRANSFER failed: %d\n", ret); #endif } else { /* The I2C transfer was successful... break out of the loop and * return the value read. */ audinfo("Read: %02x -> %02x\n", regaddr, data); return data; } audinfo("retries=%d regaddr=%02x\n", retries, regaddr); } /* No error indication is returned on a failure... just return zero */ return 0; } /**************************************************************************** * Name: cs43l22_writereg * * Description: * Write the specified 16-bit register to the CS43L22 device. * ****************************************************************************/ static void cs43l22_writereg(FAR struct cs43l22_dev_s *priv, uint8_t regaddr, uint8_t regval) { struct i2c_config_s config; int retries; /* Setup up the I2C configuration */ config.frequency = priv->lower->frequency; config.address = priv->lower->address; config.addrlen = 7; /* Try up to three times to read the register */ for (retries = 1; retries <= 3; retries++) { uint8_t data[2]; int ret; /* Set up the data to write */ data[0] = regaddr; data[1] = regval; /* Read the register data. The returned value is the number messages * completed. */ ret = i2c_write(priv->i2c, &config, data, 2); if (ret < 0) { #ifdef CONFIG_I2C_RESET /* Perhaps the I2C bus is locked up? Try to shake the bus free */ audwarn("WARNING: i2c_write failed: %d ... Resetting\n", ret); ret = I2C_RESET(priv->i2c); if (ret < 0) { auderr("ERROR: I2C_RESET failed: %d\n", ret); break; } #else auderr("ERROR: I2C_TRANSFER failed: %d\n", ret); #endif } else { /* The I2C transfer was successful... break out of the loop and * return the value read. */ audinfo("Write: %02x <- %02x\n", regaddr, regval); return; } audinfo("retries=%d regaddr=%02x\n", retries, regaddr); } } /**************************************************************************** * Name: cs43l22_setvolume * * Description: * Set the right and left volume values in the CS43L22 device based on the * current volume and balance settings. * ****************************************************************************/ #ifndef CONFIG_AUDIO_EXCLUDE_VOLUME static void cs43l22_setvolume(FAR struct cs43l22_dev_s *priv, uint16_t volume, bool mute) { uint32_t leftlevel; uint32_t rightlevel; uint8_t regval; audinfo("volume=%u mute=%u\n", volume, mute); #ifndef CONFIG_AUDIO_EXCLUDE_BALANCE /* Calculate the left channel volume level {0..1000} */ if (priv->balance <= 500) { leftlevel = volume; } else if (priv->balance == 1000) { leftlevel = 0; } else { leftlevel = ((((1000 - priv->balance) * 100) / 500) * volume) / 100; } /* Calculate the right channel volume level {0..1000} */ if (priv->balance >= 500) { rightlevel = volume; } else if (priv->balance == 0) { rightlevel = 0; } else { rightlevel = (((priv->balance * 100) / 500) * volume) / 100; } # else leftlevel = priv->volume; rightlevel = priv->volume; # endif /* Set the volume */ regval = (rightlevel + 0x19) & 0xff; cs43l22_writereg(priv, CS43L22_MS_VOL_CTRL_A, regval); regval = ((leftlevel + 0x19) & 0xff); cs43l22_writereg(priv, CS43L22_MS_VOL_CTRL_B, regval); #if 0 regval = (rightlevel + 0x01) & 0xff; cs43l22_writereg(priv, CS43L22_HP_VOL_CTRL_A, regval); regval = (leftlevel + 0x01) & 0xff; cs43l22_writereg(priv, CS43L22_HP_VOL_CTRL_B, regval); #endif regval = cs43l22_readreg(priv, CS43L22_PLAYBACK_CTRL2); if (mute) { regval |= (CS43L22_HPAMUTE | CS43L22_HPBMUTE); } else { regval &= ~(CS43L22_HPAMUTE | CS43L22_HPBMUTE); } cs43l22_writereg(priv, CS43L22_PLAYBACK_CTRL2, regval); /* Remember the volume level and mute settings */ priv->volume = volume; priv->mute = mute; } #endif /* CONFIG_AUDIO_EXCLUDE_VOLUME */ /**************************************************************************** * Name: cs43l22_setbass * * Description: * Set the bass level. * * The level and range are in whole percentage levels (0-100). * ****************************************************************************/ #ifndef CONFIG_AUDIO_EXCLUDE_TONE static void cs43l22_setbass(FAR struct cs43l22_dev_s *priv, uint8_t bass) { audinfo("bass=%u\n", bass); #warning Missing logic } #endif /* CONFIG_AUDIO_EXCLUDE_TONE */ /**************************************************************************** * Name: cs43l22_settreble * * Description: * Set the treble level . * * The level and range are in whole percentage levels (0-100). * ****************************************************************************/ #ifndef CONFIG_AUDIO_EXCLUDE_TONE static void cs43l22_settreble(FAR struct cs43l22_dev_s *priv, uint8_t treble) { audinfo("treble=%u\n", treble); #warning Missing logic } #endif /* CONFIG_AUDIO_EXCLUDE_TONE */ /**************************************************************************** * Name: cs43l22_setdatawidth * * Description: * Set the 8- or 16-bit data modes * ****************************************************************************/ static void cs43l22_setdatawidth(FAR struct cs43l22_dev_s *priv) { if (priv->bpsamp == 16) { /* Reset default default setting */ priv->i2s->ops->i2s_txdatawidth(priv->i2s, 16); } else { /* This should select 8-bit with no companding */ priv->i2s->ops->i2s_txdatawidth(priv->i2s, 8); } } /**************************************************************************** * Name: cs43l22_setbitrate * ****************************************************************************/ static void cs43l22_setbitrate(FAR struct cs43l22_dev_s *priv) { DEBUGASSERT(priv && priv->lower); priv->i2s->ops->i2s_txsamplerate(priv->i2s, priv->samprate); audinfo("sample rate=%u nchannels=%u bpsamp=%u\n", priv->samprate, priv->nchannels, priv->bpsamp); } /**************************************************************************** * Name: cs43l22_getcaps * * Description: * Get the audio device capabilities * ****************************************************************************/ static int cs43l22_getcaps(FAR struct audio_lowerhalf_s *dev, int type, FAR struct audio_caps_s *caps) { /* Validate the structure */ DEBUGASSERT(caps && caps->ac_len >= sizeof(struct audio_caps_s)); audinfo("type=%d ac_type=%d\n", type, caps->ac_type); /* Fill in the caller's structure based on requested info */ caps->ac_format.hw = 0; caps->ac_controls.w = 0; switch (caps->ac_type) { /* Caller is querying for the types of units we support */ case AUDIO_TYPE_QUERY: /* Provide our overall capabilities. The interfacing software * must then call us back for specific info for each capability. */ caps->ac_channels = 2; /* Stereo output */ switch (caps->ac_subtype) { case AUDIO_TYPE_QUERY: /* We don't decode any formats! Only something above us in * the audio stream can perform decoding on our behalf. */ /* The types of audio units we implement */ caps->ac_controls.b[0] = AUDIO_TYPE_OUTPUT | AUDIO_TYPE_FEATURE | AUDIO_TYPE_PROCESSING; break; case AUDIO_FMT_MIDI: /* We only support Format 0 */ caps->ac_controls.b[0] = AUDIO_SUBFMT_END; break; default: caps->ac_controls.b[0] = AUDIO_SUBFMT_END; break; } break; /* Provide capabilities of our OUTPUT unit */ case AUDIO_TYPE_OUTPUT: caps->ac_channels = 2; switch (caps->ac_subtype) { case AUDIO_TYPE_QUERY: /* Report the Sample rates we support */ caps->ac_controls.b[0] = AUDIO_SAMP_RATE_8K | AUDIO_SAMP_RATE_11K | AUDIO_SAMP_RATE_16K | AUDIO_SAMP_RATE_22K | AUDIO_SAMP_RATE_32K | AUDIO_SAMP_RATE_44K | AUDIO_SAMP_RATE_48K; break; case AUDIO_FMT_MP3: case AUDIO_FMT_WMA: case AUDIO_FMT_PCM: break; default: break; } break; /* Provide capabilities of our FEATURE units */ case AUDIO_TYPE_FEATURE: /* If the sub-type is UNDEF, then report the Feature Units we * support. */ if (caps->ac_subtype == AUDIO_FU_UNDEF) { /* Fill in the ac_controls section with the Feature Units we * have. */ caps->ac_controls.b[0] = AUDIO_FU_VOLUME | AUDIO_FU_BASS | AUDIO_FU_TREBLE; caps->ac_controls.b[1] = AUDIO_FU_BALANCE >> 8; } else { /* TODO: Do we need to provide specific info for the Feature * Units, such as volume setting ranges, etc.? */ } break; /* Provide capabilities of our PROCESSING unit */ case AUDIO_TYPE_PROCESSING: switch (caps->ac_subtype) { case AUDIO_PU_UNDEF: /* Provide the type of Processing Units we support */ caps->ac_controls.b[0] = AUDIO_PU_STEREO_EXTENDER; break; case AUDIO_PU_STEREO_EXTENDER: /* Provide capabilities of our Stereo Extender */ caps->ac_controls.b[0] = AUDIO_STEXT_ENABLE | AUDIO_STEXT_WIDTH; break; default: /* Other types of processing uint we don't support */ break; } break; /* All others we don't support */ default: /* Zero out the fields to indicate no support */ caps->ac_subtype = 0; caps->ac_channels = 0; break; } /* Return the length of the audio_caps_s struct for validation of * proper Audio device type. */ return caps->ac_len; } /**************************************************************************** * Name: cs43l22_configure * * Description: * Configure the audio device for the specified mode of operation. * ****************************************************************************/ #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_configure(FAR struct audio_lowerhalf_s *dev, FAR void *session, FAR const struct audio_caps_s *caps) #else static int cs43l22_configure(FAR struct audio_lowerhalf_s *dev, FAR const struct audio_caps_s *caps) #endif { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; int ret = OK; DEBUGASSERT(priv != NULL && caps != NULL); audinfo("ac_type: %d\n", caps->ac_type); /* Process the configure operation */ switch (caps->ac_type) { case AUDIO_TYPE_FEATURE: audinfo(" AUDIO_TYPE_FEATURE\n"); /* Process based on Feature Unit */ switch (caps->ac_format.hw) { #ifndef CONFIG_AUDIO_EXCLUDE_VOLUME case AUDIO_FU_VOLUME: { /* Set the volume */ uint16_t volume = caps->ac_controls.hw[0]; audinfo(" Volume: %d\n", volume); if (volume >= 0 && volume <= 1000) { /* Scale the volume setting to the range {76..255} */ cs43l22_setvolume(priv, (179 * volume / 1000) + 76, priv->mute); } else { ret = -EDOM; } } break; #endif /* CONFIG_AUDIO_EXCLUDE_VOLUME */ #ifndef CONFIG_AUDIO_EXCLUDE_BALANCE case AUDIO_FU_BALANCE: { /* Set the Balance */ uint16_t balance = caps->ac_controls.hw[0]; audinfo(" Balance: %d\n", balance); if (balance >= 0 && balance <= 1000) { /* Scale the volume setting to the range {76..255} */ cs43l22_setvolume(priv, (179 * priv->volume / 1000) + 76, priv->mute); } else { ret = -EDOM; } } break; #endif /* CONFIG_AUDIO_EXCLUDE_VOLUME */ #ifndef CONFIG_AUDIO_EXCLUDE_TONE case AUDIO_FU_BASS: { /* Set the bass. The percentage level (0-100) is in the * ac_controls.b[0] parameter. */ uint8_t bass = caps->ac_controls.b[0]; audinfo(" Bass: %d\n", bass); if (bass <= 100) { cs43l22_setbass(priv, bass); } else { ret = -EDOM; } } break; case AUDIO_FU_TREBLE: { /* Set the treble. The percentage level (0-100) is in the * ac_controls.b[0] parameter. */ uint8_t treble = caps->ac_controls.b[0]; audinfo(" Treble: %d\n", treble); if (treble <= 100) { cs43l22_settreble(priv, treble); } else { ret = -EDOM; } } break; #endif /* CONFIG_AUDIO_EXCLUDE_TONE */ default: auderr(" ERROR: Unrecognized feature unit\n"); ret = -ENOTTY; break; } break; case AUDIO_TYPE_OUTPUT: { audinfo(" AUDIO_TYPE_OUTPUT:\n"); audinfo(" Number of channels: %u\n", caps->ac_channels); audinfo(" Sample rate: %u\n", caps->ac_controls.hw[0]); audinfo(" Sample width: %u\n", caps->ac_controls.b[2]); /* Verify that all of the requested values are supported */ ret = -ERANGE; if (caps->ac_channels != 1 && caps->ac_channels != 2) { auderr("ERROR: Unsupported number of channels: %d\n", caps->ac_channels); break; } if (caps->ac_controls.b[2] != 8 && caps->ac_controls.b[2] != 16) { auderr("ERROR: Unsupported bits per sample: %d\n", caps->ac_controls.b[2]); break; } /* Save the current stream configuration */ priv->samprate = caps->ac_controls.hw[0]; priv->nchannels = caps->ac_channels; priv->bpsamp = caps->ac_controls.b[2]; /* Reconfigure the FLL to support the resulting number or channels, * bits per sample, and bitrate. */ cs43l22_setdatawidth(priv); cs43l22_setbitrate(priv); cs43l22_clock_analysis(&priv->dev, "AUDIO_TYPE_OUTPUT"); ret = OK; } break; case AUDIO_TYPE_PROCESSING: break; } return ret; } /**************************************************************************** * Name: cs43l22_shutdown * * Description: * Shutdown the CS43L22 chip and put it in the lowest power state possible. * ****************************************************************************/ static int cs43l22_shutdown(FAR struct audio_lowerhalf_s *dev) { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; DEBUGASSERT(priv); /* First disable interrupts */ CS43L22_DISABLE(priv->lower); /* Now issue a software reset. This puts all CS43L22 registers back in * their default state. */ cs43l22_reset(priv); return OK; } /**************************************************************************** * Name: cs43l22_senddone * * Description: * This is the I2S callback function that is invoked when the transfer * completes. * ****************************************************************************/ static void cs43l22_senddone(FAR struct i2s_dev_s *i2s, FAR struct ap_buffer_s *apb, FAR void *arg, int result) { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)arg; struct audio_msg_s msg; irqstate_t flags; int ret; DEBUGASSERT(i2s && priv && priv->running && apb); audinfo("apb=%p inflight=%d result=%d\n", apb, priv->inflight, result); /* We do not place any restriction on the context in which this function * is called. It may be called from an interrupt handler. Therefore, the * doneq and in-flight values might be accessed from the interrupt level. * Not the best design. But we will use interrupt controls to protect * against that possibility. */ flags = enter_critical_section(); /* Add the completed buffer to the end of our doneq. We do not yet * decrement the reference count. */ dq_addlast((FAR dq_entry_t *)apb, &priv->doneq); /* And decrement the number of buffers in-flight */ DEBUGASSERT(priv->inflight > 0); priv->inflight--; /* Save the result of the transfer */ /* REVISIT: This can be overwritten */ priv->result = result; leave_critical_section(flags); /* Now send a message to the worker thread, informing it that there are * buffers in the done queue that need to be cleaned up. */ msg.msg_id = AUDIO_MSG_COMPLETE; ret = file_mq_send(&priv->mq, (FAR const char *)&msg, sizeof(msg), CONFIG_CS43L22_MSG_PRIO); if (ret < 0) { auderr("ERROR: file_mq_send failed: %d\n", ret); } } /**************************************************************************** * Name: cs43l22_returnbuffers * * Description: * This function is called after the complete of one or more data * transfers. This function will empty the done queue and release our * reference to each buffer. * ****************************************************************************/ static void cs43l22_returnbuffers(FAR struct cs43l22_dev_s *priv) { FAR struct ap_buffer_s *apb; irqstate_t flags; /* The doneq and in-flight values might be accessed from the interrupt * level in some implementations. Not the best design. But we will * use interrupt controls to protect against that possibility. */ flags = enter_critical_section(); while (dq_peek(&priv->doneq) != NULL) { /* Take the next buffer from the queue of completed transfers */ apb = (FAR struct ap_buffer_s *)dq_remfirst(&priv->doneq); leave_critical_section(flags); audinfo("Returning: apb=%p curbyte=%d nbytes=%d flags=%04x\n", apb, apb->curbyte, apb->nbytes, apb->flags); /* Are we returning the final buffer in the stream? */ if ((apb->flags & AUDIO_APB_FINAL) != 0) { /* Both the pending and the done queues should be empty and there * should be no buffers in-flight. */ DEBUGASSERT(dq_empty(&priv->doneq) && dq_empty(&priv->pendq) && priv->inflight == 0); /* Set the terminating flag. This will, eventually, cause the * worker thread to exit (if it is not already terminating). */ audinfo("Terminating\n"); priv->terminating = true; } /* Release our reference to the audio buffer */ apb_free(apb); /* Send the buffer back up to the previous level. */ #ifdef CONFIG_AUDIO_MULTI_SESSION priv->dev.upper(priv->dev.priv, AUDIO_CALLBACK_DEQUEUE, apb, OK, NULL); #else priv->dev.upper(priv->dev.priv, AUDIO_CALLBACK_DEQUEUE, apb, OK); #endif flags = enter_critical_section(); } leave_critical_section(flags); } /**************************************************************************** * Name: cs43l22_sendbuffer * * Description: * Start the transfer an audio buffer to the CS43L22 via I2S. This * will not wait for the transfer to complete but will return immediately. * the wmd8904_senddone called will be invoked when the transfer * completes, stimulating the worker thread to call this function again. * ****************************************************************************/ static int cs43l22_sendbuffer(FAR struct cs43l22_dev_s *priv) { FAR struct ap_buffer_s *apb; irqstate_t flags; uint32_t timeout; int shift; int ret; /* Loop while there are audio buffers to be sent and we have few than * CONFIG_CS43L22_INFLIGHT then "in-flight" * * The 'inflight' value might be modified from the interrupt level in some * implementations. We will use interrupt controls to protect against * that possibility. * * The 'pendq', on the other hand, is protected via a semaphore. Let's * hold the semaphore while we are busy here and disable the interrupts * only while accessing 'inflight'. */ ret = nxmutex_lock(&priv->pendlock); if (ret < 0) { return ret; } while (priv->inflight < CONFIG_CS43L22_INFLIGHT && dq_peek(&priv->pendq) != NULL && !priv->paused) { /* Take next buffer from the queue of pending transfers */ apb = (FAR struct ap_buffer_s *)dq_remfirst(&priv->pendq); audinfo("Sending apb=%p, size=%d inflight=%d\n", apb, apb->nbytes, priv->inflight); /* Increment the number of buffers in-flight before sending in order * to avoid a possible race condition. */ flags = enter_critical_section(); priv->inflight++; leave_critical_section(flags); /* Send the entire audio buffer via I2S. What is a reasonable timeout * to use? This would depend on the bit rate and size of the buffer. * * Samples in the buffer (samples): * = buffer_size * 8 / bpsamp samples * Sample rate (samples/second): * = samplerate * nchannels * Expected transfer time (seconds): * = (buffer_size * 8) / bpsamp / samplerate / nchannels * * We will set the timeout about twice that. * * NOTES: * - The multiplier of 8 becomes 16000 for 2x and units of * milliseconds. * - 16000 is a approximately 16384 (1 << 14), bpsamp is either * (1 << 3) or (1 << 4), and nchannels is either (1 << 0) or * (1 << 1). So this can be simplifies to (milliseconds): * * = (buffer_size << shift) / samplerate */ shift = (priv->bpsamp == 8) ? 14 - 3 : 14 - 4; shift -= (priv->nchannels > 1) ? 1 : 0; timeout = MSEC2TICK(((uint32_t)(apb->nbytes - apb->curbyte) << shift) / (uint32_t)priv->samprate); ret = I2S_SEND(priv->i2s, apb, cs43l22_senddone, priv, timeout); if (ret < 0) { auderr("ERROR: I2S_SEND failed: %d\n", ret); break; } } nxmutex_unlock(&priv->pendlock); return ret; } /**************************************************************************** * Name: cs43l22_start * * Description: * Start the configured operation (audio streaming, volume enabled, etc.). * ****************************************************************************/ #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_start(FAR struct audio_lowerhalf_s *dev, FAR void *session) #else static int cs43l22_start(FAR struct audio_lowerhalf_s *dev) #endif { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; struct sched_param sparam; struct mq_attr attr; pthread_attr_t tattr; FAR void *value; int ret; audinfo("Entry\n"); /* Exit reduced power modes of operation */ /* REVISIT */ /* Create a message queue for the worker thread */ snprintf(priv->mqname, sizeof(priv->mqname), "/tmp/%" PRIXPTR, (uintptr_t)priv); attr.mq_maxmsg = 16; attr.mq_msgsize = sizeof(struct audio_msg_s); attr.mq_curmsgs = 0; attr.mq_flags = 0; ret = file_mq_open(&priv->mq, priv->mqname, O_RDWR | O_CREAT, 0644, &attr); if (ret < 0) { /* Error creating message queue! */ auderr("ERROR: Couldn't allocate message queue\n"); return ret; } /* Join any old worker thread we had created to prevent a memory leak */ if (priv->threadid != 0) { audinfo("Joining old thread\n"); pthread_join(priv->threadid, &value); } /* Start our thread for sending data to the device */ pthread_attr_init(&tattr); sparam.sched_priority = sched_get_priority_max(SCHED_FIFO) - 3; pthread_attr_setschedparam(&tattr, &sparam); pthread_attr_setstacksize(&tattr, CONFIG_CS43L22_WORKER_STACKSIZE); audinfo("Starting worker thread\n"); ret = pthread_create(&priv->threadid, &tattr, cs43l22_workerthread, (pthread_addr_t)priv); if (ret != OK) { auderr("ERROR: pthread_create failed: %d\n", ret); } else { pthread_setname_np(priv->threadid, "cs43l22"); audinfo("Created worker thread\n"); } return ret; } /**************************************************************************** * Name: cs43l22_stop * * Description: * Stop the configured operation (audio streaming, volume disabled, etc.). * ****************************************************************************/ #ifndef CONFIG_AUDIO_EXCLUDE_STOP # ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_stop(FAR struct audio_lowerhalf_s *dev, FAR void *session) # else static int cs43l22_stop(FAR struct audio_lowerhalf_s *dev) # endif { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; struct audio_msg_s term_msg; FAR void *value; /* Send a message to stop all audio streaming */ term_msg.msg_id = AUDIO_MSG_STOP; term_msg.u.data = 0; file_mq_send(&priv->mq, (FAR const char *)&term_msg, sizeof(term_msg), CONFIG_CS43L22_MSG_PRIO); /* Join the worker thread */ pthread_join(priv->threadid, &value); priv->threadid = 0; /* Enter into a reduced power usage mode */ /* REVISIT: */ return OK; } #endif /**************************************************************************** * Name: cs43l22_pause * * Description: * Pauses the playback. * ****************************************************************************/ #ifndef CONFIG_AUDIO_EXCLUDE_PAUSE_RESUME # ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_pause(FAR struct audio_lowerhalf_s *dev, FAR void *session) # else static int cs43l22_pause(FAR struct audio_lowerhalf_s *dev) # endif { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; if (priv->running && !priv->paused) { /* Disable interrupts to prevent us from suppling any more data */ priv->paused = true; cs43l22_setvolume(priv, priv->volume, true); CS43L22_DISABLE(priv->lower); } return OK; } #endif /* CONFIG_AUDIO_EXCLUDE_PAUSE_RESUME */ /**************************************************************************** * Name: cs43l22_resume * * Description: * Resumes the playback. * ****************************************************************************/ #ifndef CONFIG_AUDIO_EXCLUDE_PAUSE_RESUME # ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_resume(FAR struct audio_lowerhalf_s *dev, FAR void *session) # else static int cs43l22_resume(FAR struct audio_lowerhalf_s *dev) # endif { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; if (priv->running && priv->paused) { priv->paused = false; cs43l22_setvolume(priv, priv->volume, false); /* Enable interrupts to allow sampling data */ cs43l22_sendbuffer(priv); #ifdef CS43L22_USE_FFLOCK_INT CS43L22_ENABLE(priv->lower); #endif } return OK; } #endif /* CONFIG_AUDIO_EXCLUDE_PAUSE_RESUME */ /**************************************************************************** * Name: cs43l22_enqueuebuffer * * Description: * Enqueue an Audio Pipeline Buffer for playback/ processing. * ****************************************************************************/ static int cs43l22_enqueuebuffer(FAR struct audio_lowerhalf_s *dev, FAR struct ap_buffer_s *apb) { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; struct audio_msg_s term_msg; int ret; audinfo("Enqueueing: apb=%p curbyte=%d nbytes=%d flags=%04x\n", apb, apb->curbyte, apb->nbytes, apb->flags); ret = nxmutex_lock(&priv->pendlock); if (ret < 0) { return ret; } /* Take a reference on the new audio buffer */ apb_reference(apb); /* Add the new buffer to the tail of pending audio buffers */ apb->flags |= AUDIO_APB_OUTPUT_ENQUEUED; dq_addlast(&apb->dq_entry, &priv->pendq); nxmutex_unlock(&priv->pendlock); /* Send a message to the worker thread indicating that a new buffer has * been enqueued. If mq is NULL, then the playing has not yet started. * In that case we are just "priming the pump" and we don't need to send * any message. */ ret = OK; if (priv->mq.f_inode != NULL) { term_msg.msg_id = AUDIO_MSG_ENQUEUE; term_msg.u.data = 0; ret = file_mq_send(&priv->mq, (FAR const char *)&term_msg, sizeof(term_msg), CONFIG_CS43L22_MSG_PRIO); if (ret < 0) { auderr("ERROR: file_mq_send failed: %d\n", ret); } } return ret; } /**************************************************************************** * Name: cs43l22_cancelbuffer * * Description: * Called when an enqueued buffer is being cancelled. * ****************************************************************************/ static int cs43l22_cancelbuffer(FAR struct audio_lowerhalf_s *dev, FAR struct ap_buffer_s *apb) { audinfo("apb=%p\n", apb); return OK; } /**************************************************************************** * Name: cs43l22_ioctl * * Description: * Perform a device ioctl * ****************************************************************************/ static int cs43l22_ioctl(FAR struct audio_lowerhalf_s *dev, int cmd, unsigned long arg) { int ret = OK; #ifdef CONFIG_AUDIO_DRIVER_SPECIFIC_BUFFERS FAR struct ap_buffer_info_s *bufinfo; #endif /* Deal with ioctls passed from the upper-half driver */ switch (cmd) { /* Check for AUDIOIOC_HWRESET ioctl. This ioctl is passed straight * through from the upper-half audio driver. */ case AUDIOIOC_HWRESET: { /* REVISIT: Should we completely re-initialize the chip? We * can't just issue a software reset; that would puts all WM8904 * registers back in their default state. */ audinfo("AUDIOIOC_HWRESET:\n"); } break; /* Report our preferred buffer size and quantity */ #ifdef CONFIG_AUDIO_DRIVER_SPECIFIC_BUFFERS case AUDIOIOC_GETBUFFERINFO: { audinfo("AUDIOIOC_GETBUFFERINFO:\n"); bufinfo = (FAR struct ap_buffer_info_s *)arg; bufinfo->buffer_size = CONFIG_CS43L22_BUFFER_SIZE; bufinfo->nbuffers = CONFIG_CS43L22_NUM_BUFFERS; } break; #endif default: ret = -ENOTTY; audinfo("Ignored\n"); break; } return ret; } /**************************************************************************** * Name: cs43l22_reserve * * Description: * Reserves a session (the only one we have). * ****************************************************************************/ #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_reserve(FAR struct audio_lowerhalf_s *dev, FAR void **session) #else static int cs43l22_reserve(FAR struct audio_lowerhalf_s *dev) #endif { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; int ret = OK; /* Borrow the APBQ mutex for thread sync */ ret = nxmutex_lock(&priv->pendlock); if (ret < 0) { return ret; } if (priv->reserved) { ret = -EBUSY; } else { /* Initialize the session context */ #ifdef CONFIG_AUDIO_MULTI_SESSION *session = NULL; #endif priv->inflight = 0; priv->running = false; priv->paused = false; #ifndef CONFIG_AUDIO_EXCLUDE_STOP priv->terminating = false; #endif priv->reserved = true; } nxmutex_unlock(&priv->pendlock); return ret; } /**************************************************************************** * Name: cs43l22_release * * Description: * Releases the session (the only one we have). * ****************************************************************************/ #ifdef CONFIG_AUDIO_MULTI_SESSION static int cs43l22_release(FAR struct audio_lowerhalf_s *dev, FAR void *session) #else static int cs43l22_release(FAR struct audio_lowerhalf_s *dev) #endif { FAR struct cs43l22_dev_s *priv = (FAR struct cs43l22_dev_s *)dev; FAR void *value; int ret; /* Join any old worker thread we had created to prevent a memory leak */ if (priv->threadid != 0) { pthread_join(priv->threadid, &value); priv->threadid = 0; } /* Borrow the APBQ mutex for thread sync */ ret = nxmutex_lock(&priv->pendlock); /* Really we should free any queued buffers here */ priv->reserved = false; nxmutex_unlock(&priv->pendlock); return ret; } /**************************************************************************** * Name: cs43l22_interrupt_work * * Description: * CS43L22 interrupt actions cannot be performed in the interrupt handler * because I2C access is not possible in that context. Instead, all I2C * operations are deferred to the work queue. * * Assumptions: * CS43L22 interrupts were disabled in the interrupt handler. * ****************************************************************************/ #ifdef CS43L22_USE_FFLOCK_INT static void cs43l22_interrupt_work(FAR void *arg) { /* TODO */ #warning Missing logic } #endif /**************************************************************************** * Name: cs43l22_interrupt * * Description: * This is the ISR that services the GPIO1/IRQ pin from the CS43L22. It * signals CS43L22 events such FLL lock. * ****************************************************************************/ #ifdef CS43L22_USE_FFLOCK_INT static int cs43l22_interrupt(FAR const struct cs43l22_lower_s *lower, FAR void *arg) { /* TODO */ #warning Missing logic } #endif /**************************************************************************** * Name: cs43l22_workerthread * * This is the thread that feeds data to the chip and keeps the audio * stream going. * ****************************************************************************/ static void *cs43l22_workerthread(pthread_addr_t pvarg) { FAR struct cs43l22_dev_s *priv = (struct cs43l22_dev_s *)pvarg; struct audio_msg_s msg; FAR struct ap_buffer_s *apb; int msglen; unsigned int prio; audinfo("Entry\n"); #ifndef CONFIG_AUDIO_EXCLUDE_STOP priv->terminating = false; #endif /* Mark ourself as running and make sure that CS43L22 interrupts are * enabled. */ priv->running = true; #ifdef CS43L22_USE_FFLOCK_INT CS43L22_ENABLE(priv->lower); #endif cs43l22_setvolume(priv, priv->volume, false); /* Loop as long as we are supposed to be running and as long as we have * buffers in-flight. */ while (priv->running || priv->inflight > 0) { /* Check if we have been asked to terminate. We have to check if we * still have buffers in-flight. If we do, then we can't stop until * birds come back to roost. */ if (priv->terminating && priv->inflight <= 0) { /* We are IDLE. Break out of the loop and exit. */ break; } else { /* Check if we can send more audio buffers to the CS43L22 */ cs43l22_sendbuffer(priv); } /* Wait for messages from our message queue */ msglen = file_mq_receive(&priv->mq, (FAR char *)&msg, sizeof(msg), &prio); /* Handle the case when we return with no message */ if (msglen < sizeof(struct audio_msg_s)) { auderr("ERROR: Message too small: %d\n", msglen); continue; } /* Process the message */ switch (msg.msg_id) { /* The ISR has requested more data. We will catch this case at * the top of the loop. */ case AUDIO_MSG_DATA_REQUEST: audinfo("AUDIO_MSG_DATA_REQUEST\n"); break; /* Stop the playback */ #ifndef CONFIG_AUDIO_EXCLUDE_STOP case AUDIO_MSG_STOP: /* Indicate that we are terminating */ audinfo("AUDIO_MSG_STOP: Terminating\n"); priv->terminating = true; break; #endif /* We have a new buffer to send. We will catch this case at * the top of the loop. */ case AUDIO_MSG_ENQUEUE: audinfo("AUDIO_MSG_ENQUEUE\n"); break; /* We will wake up from the I2S callback with this message */ case AUDIO_MSG_COMPLETE: audinfo("AUDIO_MSG_COMPLETE\n"); cs43l22_returnbuffers(priv); break; default: auderr("ERROR: Ignoring message ID %d\n", msg.msg_id); break; } } /* Reset the CS43L22 hardware */ cs43l22_reset(priv); /* Return any pending buffers in our pending queue */ nxmutex_lock(&priv->pendlock); while ((apb = (FAR struct ap_buffer_s *)dq_remfirst(&priv->pendq)) != NULL) { /* Release our reference to the buffer */ apb_free(apb); /* Send the buffer back up to the previous level. */ #ifdef CONFIG_AUDIO_MULTI_SESSION priv->dev.upper(priv->dev.priv, AUDIO_CALLBACK_DEQUEUE, apb, OK, NULL); #else priv->dev.upper(priv->dev.priv, AUDIO_CALLBACK_DEQUEUE, apb, OK); #endif } nxmutex_unlock(&priv->pendlock); /* Return any pending buffers in our done queue */ cs43l22_returnbuffers(priv); /* Close the message queue */ file_mq_close(&priv->mq); file_mq_unlink(priv->mqname); /* Send an AUDIO_MSG_COMPLETE message to the client */ #ifdef CONFIG_AUDIO_MULTI_SESSION priv->dev.upper(priv->dev.priv, AUDIO_CALLBACK_COMPLETE, NULL, OK, NULL); #else priv->dev.upper(priv->dev.priv, AUDIO_CALLBACK_COMPLETE, NULL, OK); #endif audinfo("Exit\n"); return NULL; } /**************************************************************************** * Name: cs43l22_audio_output * * Description: * Initialize and configure the CS43L22 device as an audio output device. * * Input Parameters: * priv - A reference to the driver state structure * * Returned Value: * None. No failures are detected. * ****************************************************************************/ static void cs43l22_audio_output(FAR struct cs43l22_dev_s *priv) { uint8_t regval; /* Keep codec powered off */ regval = CS43L22_POWER_DOWN; cs43l22_writereg(priv, CS43L22_POWER_CTRL1, regval); /* SPK always off and HP always on */ regval = CS43L22_PDN_HPB_ON | CS43L22_PDN_HPA_ON | CS43L22_PDN_SPKB_OFF | CS43L22_PDN_SPKA_OFF; cs43l22_writereg(priv, CS43L22_POWER_CTRL2, regval); /* Clock configuration: Auto detection */ regval = CS43L22_AUTO_DETECT_ENABLE | CS43L22_CLKDIV2_ENABLE; cs43l22_writereg(priv, CS43L22_CLOCK_CTRL, regval); /* Set slave mode and Philips audio standard */ regval = CS43L22_DAC_IF_I2S; cs43l22_writereg(priv, CS43L22_INTERFACE_CTRL1, regval); /* Power on the codec */ regval = CS43L22_POWER_UP; cs43l22_writereg(priv, CS43L22_POWER_CTRL1, regval); /* Disable the analog soft ramp */ regval = 0x00; cs43l22_writereg(priv, CS43L22_ANLG_ZC_SR_SEL, regval); /* Disable the digital soft ramp */ regval = CS43L22_DEEMPHASIS_ENABLE; cs43l22_writereg(priv, CS43L22_MISCLLNS_CTRL, regval); /* Disable the limiter attack level */ regval = 0x00; cs43l22_writereg(priv, CS43L22_LIM_CTRL1, regval); /* Adjust bass and treble levels */ regval = CS43L22_BASS_GAIN(0x0f); cs43l22_writereg(priv, CS43L22_TONE_CTRL, regval); /* Adjust PCM volume level */ regval = 0x0a; cs43l22_writereg(priv, CS43L22_PCM_VOL_A, regval); cs43l22_writereg(priv, CS43L22_PCM_VOL_B, regval); cs43l22_setdatawidth(priv); cs43l22_setvolume(priv, CONFIG_CS43L22_INITVOLUME, false); } /**************************************************************************** * Name: cs43l22_audio_input * * Description: * Initialize and configure the CS43L22 device as an audio output device * (Right input only). cs43l22_audio_output() must be called first, this * function then modifies the configuration to support audio input. * * Input Parameters: * priv - A reference to the driver state structure * * Returned Value: * None. No failures are detected. * ****************************************************************************/ #if 0 /* Not used */ static void cs43l22_audio_input(FAR struct cs43l22_dev_s *priv) { /* TODO */ #warning Missing logic } #endif /**************************************************************************** * Name: cs43l22_configure_ints * * Description: * Configure the GPIO/IRQ interrupt * * Input Parameters: * priv - A reference to the driver state structure * * Returned Value: * None * ****************************************************************************/ #ifdef CS43L22_USE_FFLOCK_INT static void cs43l22_configure_ints(FAR struct cs43l22_dev_s *priv) { /* TODO */ #warning Missing logic } #endif /**************************************************************************** * Name: cs43l22_reset * * Description: * Reset and re-initialize the CS43L22 * * Input Parameters: * priv - A reference to the driver state structure * * Returned Value: * None * ****************************************************************************/ static void cs43l22_reset(FAR struct cs43l22_dev_s *priv) { /* Put audio output back to its initial configuration */ /* Put audio output back to its initial configuration */ priv->samprate = CS43L22_DEFAULT_SAMPRATE; priv->nchannels = CS43L22_DEFAULT_NCHANNELS; priv->bpsamp = CS43L22_DEFAULT_BPSAMP; #if !defined(CONFIG_AUDIO_EXCLUDE_VOLUME) && !defined(CONFIG_AUDIO_EXCLUDE_BALANCE) priv->balance = 500; /* b16HALF = Center balance */ #endif /* Software reset. This puts all CS43L22 registers back in their * default state. */ /* cs43l22_writereg(priv, CS43L22_SWRST, 0); */ /* Configure the CS43L22 hardware as an audio input device */ cs43l22_audio_output(priv); /* Configure interrupts */ /* cs43l22_configure_ints(priv); */ /* Configure the FLL and the LRCLK */ cs43l22_setbitrate(priv); /* Dump some information and return the device instance */ cs43l22_dump_registers(&priv->dev, "After configuration"); cs43l22_clock_analysis(&priv->dev, "After configuration"); } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: cs43l22_initialize * * Description: * Initialize the CS43L22 device. * * Input Parameters: * i2c - An I2C driver instance * i2s - An I2S driver instance * lower - Persistent board configuration data * * Returned Value: * A new lower half audio interface for the CS43L22 device is returned on * success; NULL is returned on failure. * ****************************************************************************/ FAR struct audio_lowerhalf_s * cs43l22_initialize(FAR struct i2c_master_s *i2c, FAR struct i2s_dev_s *i2s, FAR const struct cs43l22_lower_s *lower) { FAR struct cs43l22_dev_s *priv; uint16_t regval; /* Sanity check */ DEBUGASSERT(i2c && i2s && lower); /* Allocate a CS43L22 device structure */ priv = (FAR struct cs43l22_dev_s *) kmm_zalloc(sizeof(struct cs43l22_dev_s)); if (priv) { /* Initialize the CS43L22 device structure. Since we used kmm_zalloc, * only the non-zero elements of the structure need to be initialized. */ priv->dev.ops = &g_audioops; priv->lower = lower; priv->i2c = i2c; priv->i2s = i2s; nxmutex_init(&priv->pendlock); dq_init(&priv->pendq); dq_init(&priv->doneq); /* Initialize I2C */ audinfo("address=%02x frequency=%" PRId32 "\n", lower->address, lower->frequency); /* Software reset. This puts all CS43L22 registers back in their * default state. */ CS43L22_HW_RESET(priv->lower); cs43l22_dump_registers(&priv->dev, "After reset"); /* Verify that CS43L22 is present and available on this I2C */ regval = cs43l22_readreg(priv, CS43L22_ID_REV); if ((regval & 0xff) != CS43L22_DEV_ID_REV) { auderr("ERROR: CS43L22 not found: ID=%02x\n", regval); goto errout_with_dev; } /* Reset and reconfigure the CS43L22 hardware */ cs43l22_reset(priv); return &priv->dev; } return NULL; errout_with_dev: nxmutex_destroy(&priv->pendlock); kmm_free(priv); return NULL; }