#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

if ARCH_BOARD_SAMA5D4_EK

choice
	prompt "SAMA5D4-EK Board Version"
	default SAMA5D4_MB_REVC

config SAMA5D4_MB_REVC
	bool "SAMA5D44-MB Rev. C"

config SAMA5D4_MB_REVE
	bool "SAMA5D44-MB Rev. E"

endchoice # SAMA5D4-EK Board Version

choice
	prompt "CPU Frequency"
	default SAMA5D4EK_396MHZ

config SAMA5D4EK_384MHZ
	bool "384 MHz"

config SAMA5D4EK_396MHZ
	bool "396 MHz"

config SAMA5D4EK_528MHZ
	bool "528 MHz"

endchoice # CPU Frequency

choice
	prompt "SAMA4D4-EK DRAM Type"
	default SAMA5D4EK_MT47H128M16RT
	depends on SAMA5_DDRCS

config SAMA5D4EK_MT47H128M16RT
	bool "MT47H128M16RT"
	---help---
		Micron 2Gbit x16 DDR2-1066 128Mb

config SAMA5D4EK_MT47H64M16HR
	bool "MT47H64M16HR"
	---help---
		Micron 1Gbit x16 DDR2-800 64Mb

endchoice # SAMA4D4-EK DRAM Type

config SAMA5D4EK_DRAM_MAIN
	bool "Build dram_main"
	default n
	depends on SAMA5_BOOT_ISRAM
	---help---
		dram_main is a tiny program that runs in ISRAM.  dram_main will
		enable SDRAM and load an Intel HEX program into SDRAM over the
		serial console. Then it will either (1) jump to the program in
		DRAM at address 0x2000:0000 (2) wait for you to break in with GDB to
		debug the SDRAM program.  These different behaviors are controlled
		by SAMA5D4EK_DRAM_START.

		NOTE: If you use this boot loader, then your program must be built at
		origin 0x2000:0000, not at 0x2000:8000 as is customary with U-Boot.

config SAMA5D4EK_DRAM_START
	bool "Start DRAM program"
	default n
	depends on SAMA5D4EK_DRAM_MAIN
	---help---
		The default behavior of the DRAM boot program is to initialize the
		DRAM, then patiently wait for you to break into the program with GDB.
		An alternative behavior is enabled with this option:  If
		SAMA5D4EK_DRAM_START is defined, then it will not wait but will,
		instead, immediately start the program in DRAM.

config SAMA5D4EK_AT25_MAIN
	bool "Build at25_main"
	default n
	depends on SAMA5_BOOT_ISRAM
	---help---
		at25_main is a tiny program that runs in ISRAM.  at25_main will
		enable SDRAM and configure the AT25 Serial FLASH.  It will prompt
		and then load an Intel HEX program into SDRAM over the serial
		console. If the program is successfully loaded in SDRAM, at25_main
		will copy the program at the beginning of the AT26 Serial FLASH.
		If the jumpering is set correctly, the SAMA5D4 RomBOOT loader will
		then boot the program from the serial FLASH the next time that it
		reset.

config SAMA5D4EK_AT25_PROGSIZE
	int "AT25 partition size"
	default 131072
	depends on SAMA5D4EK_AT25_MAIN
	---help---
		This is the size of the partition at the beginning to the AT25
		serial FLASH that will be used to hold the boot program.  Since
		this program must run from SRAM, there would be no purpose int
		making this size any larger than the size of the internal SRAM.

config SAMA5D4EK_DRAM_BOOT
	bool "Using DRAM boot loader"
	default y
	depends on SAMA5_BOOT_SDRAM && !SAMA5D4EK_DRAM_MAIN && !SAMA5D4EK_AT25_MAIN
	---help---
		Select this option if you are going to boot using the sdram_main
		bootloader (created with SAMA5D4EK_DRAM_MAIN=y).  This selection
		will simply origin your program at 0x2000:0000 as required by the
		sdram_main bootloader (vs. 0x2000:8000 as required by U-Boot).

config SAMA5D4EK_NAND_BLOCKMOUNT
	bool "NAND FLASH auto-mount"
	default n
	depends on NSH_ARCHINIT && SAMA5_EBICS3_NAND
	---help---
		Automatically initialize the NAND FLASH driver when NSH starts.

choice
	prompt "NAND FLASH configuration"
	default SAMA5D4EK_NAND_NXFFS
	depends on SAMA5D4EK_NAND_BLOCKMOUNT

config SAMA5D4EK_NAND_FTL
	bool "Create NAND FLASH block driver"
	depends on MTD && MTD_NAND
	---help---
		Create the MTD driver for the NAND and "wrap" the NAND as a standard
		block driver that could then, for example, be mounted using FAT or
		any other file system.  Any file system may be used, but there will
		be no wear-leveling.

		NOTE: This options is not currently recommended.  There is not now
		NuttX file system that can handle the NAND back blocks or performs
		wear-leveling other than NXFFS and NXFFS does not use a block driver
		but, rather, operates directly upon the NAND MTD device.

config SAMA5D4EK_NAND_NXFFS
	bool "Create NAND FLASH NXFFS file system"
	depends on MTD && MTD_NAND && FS_NXFFS && NXFFS_NAND
	---help---
		Create the MTD driver for the NAND and mount the NAND device as
		a wear-leveling, NuttX FLASH file system (NXFFS).  The downside of
		NXFFS is that it can be very slow.

		NOTE: NXFFS is recommended because (1) it can handle the NAND back
		blocks and (1) performs wear-leveling.

endchoice # NAND FLASH configuration

config SAMA5D4EK_AT25_BLOCKMOUNT
	bool "AT25 serial FLASH auto-mount"
	default n
	depends on (NSH_ARCHINIT || SAMA5D4EK_AT25_MAIN) && SAMA5_SPI0 && MTD_AT25
	---help---
		Automatically initialize the AT25 SPI FLASH driver when NSH starts.

choice
	prompt "AT25 serial FLASH configuration"
	default SAMA5D4EK_AT25_FTL
	depends on SAMA5D4EK_AT25_BLOCKMOUNT

config SAMA5D4EK_AT25_FTL
	bool "Create AT25 Serial FLASH block driver"
	---help---
		Create the MTD driver for the AT25 and "wrap" the AT25 as a standard
		block driver that could then, for example, be mounted using FAT or
		any other file system.  Any file system may be used, but there will
		be no wear-leveling.

config SAMA5D4EK_AT25_CHARDEV
	bool "Create AT25 Serial FLASH character driver"
	---help---
		Create the MTD driver for the AT25 and "wrap" the AT25 as a standard
		character driver that could then, for example, via simple open, close,
		read, write file system operations.  There will be no wear-leveling
		in this configuration.

config SAMA5D4EK_AT25_NXFFS
	bool "Create AT25 serial FLASH NXFFS file system"
	depends on FS_NXFFS
	---help---
		Create the MTD driver for the AT25 and mount the AT25 device as
		a wear-leveling, NuttX FLASH file system (NXFFS).  The downside of
		NXFFS is that it can be very slow.

endchoice # AT25 serial FLASH configuration

if FS_AUTOMOUNTER

config SAMA5D4EK_HSMCI0_AUTOMOUNT
	bool "HSMCI0 automounter"
	default n
	depends on SAMA5_HSMCI0

if SAMA5D4EK_HSMCI0_AUTOMOUNT

config SAMA5D4EK_HSMCI0_AUTOMOUNT_FSTYPE
	string "HSMCI0 file system type"
	default "vfat"

config SAMA5D4EK_HSMCI0_AUTOMOUNT_BLKDEV
	string "HSMCI0 block device"
	default "/dev/mmcsd0"

config SAMA5D4EK_HSMCI0_AUTOMOUNT_MOUNTPOINT
	string "HSMCI0 mount point"
	default "/mnt/sdcard0"

config SAMA5D4EK_HSMCI0_AUTOMOUNT_DDELAY
	int "HSMCI0 debounce delay (milliseconds)"
	default 1000

config SAMA5D4EK_HSMCI0_AUTOMOUNT_UDELAY
	int "HSMCI0 unmount retry delay (milliseconds)"
	default 2000

endif # SAMA5D4EK_HSMCI0_AUTOMOUNT

config SAMA5D4EK_HSMCI1_AUTOMOUNT
	bool "HSMCI1 automounter"
	default n
	depends on SAMA5_HSMCI1

if SAMA5D4EK_HSMCI1_AUTOMOUNT

config SAMA5D4EK_HSMCI1_AUTOMOUNT_FSTYPE
	string "HSMCI1 file system type"
	default "vfat"

config SAMA5D4EK_HSMCI1_AUTOMOUNT_BLKDEV
	string "HSMCI1 block device"
	default "/dev/mmcsd1"

config SAMA5D4EK_HSMCI1_AUTOMOUNT_MOUNTPOINT
	string "HSMCI1 mount point"
	default "/mnt/sdcard1"

config SAMA5D4EK_HSMCI1_AUTOMOUNT_DDELAY
	int "HSMCI1 debounce delay (milliseconds)"
	default 1000

config SAMA5D4EK_HSMCI1_AUTOMOUNT_UDELAY
	int "HSMCI1 unmount retry delay (milliseconds)"
	default 2000

endif # SAMA5D4EK_HSMCI1_AUTOMOUNT
endif # FS_AUTOMOUNTER

config SAMA5D4EK_HSMCI0_MOUNT
	bool "HSMCI0 boot mount"
	default n
	depends on SAMA5_HSMCI0 && !SAMA5D4EK_HSMCI0_AUTOMOUNT

if SAMA5D4EK_HSMCI0_MOUNT

config SAMA5D4EK_HSMCI0_MOUNT_FSTYPE
	string "HSMCI0 file system type"
	default "vfat"

config SAMA5D4EK_HSMCI0_MOUNT_BLKDEV
	string "HSMCI0 block device"
	default "/dev/mmcsd0"

config SAMA5D4EK_HSMCI0_MOUNT_MOUNTPOINT
	string "HSMCI0 mount point"
	default "/bin"

endif # SAMA5D4EK_HSMCI0_MOUNT

config SAMA5D4EK_HSMCI1_MOUNT
	bool "HSMCI1 boot mount"
	default n
	depends on SAMA5_HSMCI1 && !SAMA5D4EK_HSMCI1_AUTOMOUNT

if SAMA5D4EK_HSMCI1_MOUNT

config SAMA5D4EK_HSMCI1_MOUNT_FSTYPE
	string "HSMCI1 file system type"
	default "vfat"

config SAMA5D4EK_HSMCI1_MOUNT_BLKDEV
	string "HSMCI1 block device"
	default "/dev/mmcsd1"

config SAMA5D4EK_HSMCI1_MOUNT_MOUNTPOINT
	string "HSMCI1 mount point"
	default "/bin"

endif # SAMA5D4EK_HSMCI1_MOUNT

config SAMA5D4EK_ROMFS_MOUNT
	bool "ROMFS boot mount"
	default n
	depends on FS_ROMFS
	---help---
		By selecting this option, you an build mount a ROMFS file system as
		part of the system boot operation.  NOTE that the board logic
		contains no a priori ROMFS file system.  In order to use this option,
		you must provide the file nuttx/configs/sama5d4-ek/include/boot_romfsimg.h.
		You might use logic in the tool at apps/tools/mkromfsimg.sh to create
		this header file.

if SAMA5D4EK_ROMFS_MOUNT

config SAMA5D4EK_ROMFS_ROMDISK_MINOR
	int "ROM disk minor device number"
	default 0

config SAMA5D4EK_ROMFS_ROMDISK_DEVNAME
	string "ROM disk block device"
	default "/dev/ram0"

config SAMA5D4EK_ROMFS_ROMDISK_SECTSIZE
	int "ROM disk sector size"
	default 512

config SAMA5D4EK_ROMFS_MOUNT_MOUNTPOINT
	string "ROMFS mount point"
	default "/bin"

endif # SAMA5D4EK_ROMFS_MOUNT

config SAMA5D4EK_USBHOST_STACKSIZE
	int "USB host waiter stack size"
	default 1536 if USBHOST_HUB
	default 1024 if !USBHOST_HUB
	depends on USBHOST

config SAMA5D4EK_USBHOST_PRIO
	int "USB host waiter task priority"
	default 100
	depends on USBHOST

if INPUT_MXT

config SAMA5D4EK_MXT_I2CFREQUENCY
	int "maXTouch I2C frequency"
	default 400000

config SAMA5D4EK_MXT_DEVMINOR
	int "/dev/input minor number"
	default 0

endif # INPUT_MXT

config SAMA5D4EK_CHANNEL
	int "PWM channel number"
	default 0 if SAMA5_PWM_CHAN0
	default 1 if SAMA5_PWM_CHAN1
	default 2 if SAMA5_PWM_CHAN2
	default 3 if SAMA5_PWM_CHAN3
	range 0 3
	depends on PWM && SAMA5_PWM
	---help---
		Selects the PWM channel number that will be used to perform the PWM
		test.  See apps/examples/pwm.

config SAMA5D4EK_SLOWCLOCK
	bool
	default y if SCHED_TICKLESS
	default n if !SCHED_TICKLESS

if AUDIO_WM8904

config SAMA5D4EK_WM8904_I2CFREQUENCY
	int "WM8904 I2C Frequency"
	default 400000
	range 1 400000
	---help---
		This option selects the I2C frequency to use when communicating with
		the WM8904 device.  The default, 400KHz, is the maximum supported by
		the WM8904.  If you have problems communicating with the WM8904,
		then you might want to try lowering this rate.

choice
	prompt "WM8904 MCLK source"
	default SAMA5D4EK_WM8904_SRCMAIN

config SAMA5D4EK_WM8904_SRCMAIN
	bool "Main Clock (12MHz)"

config SAMA5D4EK_WM8904_SRCSCK
	bool "Slow XTAL (32.768KHz)"
	select SAMA5D4EK_SLOWCLOCK

endchoice # WM8904 MCLK source
endif # AUDIO_WM8904
endif # ARCH_BOARD_SAMA5D4_EK