README ====== This directory contains the port of NuttX to the pcDuino v1 board See http://www.pcduino.com/ for information about pcDuino Lite, v1, and v2. These boards are based around the Allwinner A10 Cortex-A8 CPU. I have not compared these boards in detail, but I believe that the differences are cosmetic. This port was developed on the v1 board, but the others may be compatible: pcDuino Lite (See http://www.pcduino.com/?page_id=1707) ITEMS DETAILS -------------------- --------------------------------------------------- CPU 1GHz ARM Cortex A8 GPU OpenGL ES2.0, OpenVG 1.1 Mali 400 core DRAM 512B Onboard Storage NO Flash, microSD card (TF) slot for up to 32GB Video Output HDMI Extension Interface 2.54mm Headers Network interface 10/100Mbps RJ45 and USB WiFi extension (not included) Power 5V, 2000mA Overall Size 125mm X 52mm pcDuino v1 (http://www.pcduino.com/?page_id=12) ITEMS DETAILS -------------------- --------------------------------------------------- Items Details CPU 1GHz ARM Cortex A8 GPU OpenGL ES2.0, OpenVG 1.1 Mali 400 core * DRAM 1GB * Onboard Storage 2GB Flash, microSD card (TF) slot for up to 32GB Video Output HDMI Extension Interface 2.54mm Headers Network interface 10/100Mbps RJ45 and USB WiFi extension (not included) Power 5V, 2000mA Overall Size 125mm X 52mm pcDuino v2 (http://www.pcduino.com/?page_id=1618) ITEMS DETAILS -------------------- --------------------------------------------------- Items Details CPU 1GHz ARM Cortex A8 GPU OpenGL ES2.0, OpenVG 1.1 Mali 400 core DRAM 1GB Onboard Storage 2GB Flash, microSD card (TF) slot for up to 32GB Video Output HDMI * Extension Interface Arduino Headers * Network interface 10/100Mbps RJ45 and on-board WiFi module Power 5V, 2000mA Overall Size 125mm X 52mm Main features of the Allwinner A10 (See http://www.allwinnertech.com/en/product/a10.html): CPU - ARM Cortex™-A8 - 32KB I-Cache - 32KB D-Cache - 256KB L2 Cache GPU - ARM Mali-400 Video - UHD 2160P video decoding - 3D video decoding - Support various video decoding formats, including VP8, AVS, H. 264 MVC, VC-1, MPEG-1,2,4, etc - H.264 HP video encoding up to 1080p @ 30 fps or dual-channel 720p @ 30 fps Display - Multi-channel HD display - Integrated HDMI 1.4 - YPbPr, CVBS, VGA - Multiple LCD interfaces, including CPU, RGB, LVDS up to Full HD Memory - 32-bit DDR2/DDR3 - Memory capacity up to 16G bits - SLC/MLC/TLC/DDR NAND - 8 flash chips, 64-bit ECC Memory capacity up to 64GB Support NAND of 5xnm, 4xnm, 3xnm, 2xnm, etc Support NAND of Samsung, Toshiba, Hynix, etc Boot Devices - NAND Flash - SPI NOR Flash - SD Card - USB Contents ======== - pcDuino v1 Connectors - Serial Console - LEDs - Buttons - Booting NuttX from an SD card pcDuino v1 Connectors ===================== TOP --- - HDMI - RJ45 - USB Host (2) - J11 1. UART-Rx / GPIO0 UART2_RX 2. UART-Tx / GPIO1 UART2_TX 3. GPIO3 / GPIO2 GPIO2 4. PWM0 / GPIO3 PWM0 5. GPIO4 GPIO3 6. PWM1 / GPIO5 PWM1 7. PWM2 /GPIO6 PWM2 8. GPIO7 GPIO4 - J8 1. GPIO8 GPIO5 2. PWM3 / GPIO9 PWM3 3. SPI_CS / GPIO10 / PWM4 SPI0_CS 4. SPI_MOSI / GPIO11 / PWM5 SPI0_MOSI 5. SPI_MISO / GPIO12 SPI0_MISO 6. SPI_CLK / GPIO13 SPI0_CLK 7. Gnd 8. ARef 9. I2C-SDA TWI2_SDA 10. I2C-SCK TWI2_SCK - J12 1. ADC0 2. ADC1 3. ADC2 4. ADC3 5. ADC4 6. ADC5 - J9 1. 5V 2. Gnd 3. Gnd 4. 5V 5. 3.3V 6. Reset 7. 5V 8. NC - J5 Debug Port 1. Rx UART0-RX 2. Gnd GND 3. Tx UART0-TX - J6 SPI2 1. SPI2_MISO 2. DC_5V 3. SPI2_CLK 4. SPI2_MOSI 5. RESET# 6. GND - J7 SPI0 1. SPI0_MISO 2. DC_5V 3. SPI0_CLK 4. SPI0_MOSI 5. RESET# 6. GND - J10 1. GPIO6 2. GPIO8 3. GPIO7 4. GPIO9 Bottom ------ - USB OTG - DC Power IN (USB) - microSD card slot Serial Console ============== 1. UART0 is available on J5 Debug Port. J15 Pin 1 Rx UART0-RX UART0_RX/IR1_RX/PB23 J15 Pin 3 Tx UART0-TX UART0_TX/IR1_TX/PB22 2. UART2 is available on J11 J11 Pin1 UART-Rx / GPIO0 UART2_RX EINT31/SPI1_MISO/UART2_RX/PI19 J11 Pin2 UART-Tx / GPIO1 UART2_TX EINT30/SPI1_MOSI/UART2_TX/PI18 By default, the serial console will be provided on UART0 in all of these configurations. LEDs ==== The pcDuino v1 has four green LEDs; three can be controlled from software. Two are tied to ground and, hence, illuminated by driving the output pins to a high value: 1. LED1 SPI0_CLK SPI0_CLK/UART5_RX/EINT23/PI11 2. LED5 IPSOUT From the PMU (not controllable by software) And two are pull high and, hence, illuminated by grounding the output: 3. LED3 RX_LED LCD1_D16/ATAD12/KP_IN6/SMC_DET/EINT16/CSI1_D16/PH16 4. LED4 TX_LED LCD1_D15/ATAD11/KP_IN5/SMC_VPPPP/EINT15/CSI1_D15/PH15 These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is defined. In that case, the usage by the board port is defined in include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related events as follows: SYMBOL Meaning LED state LED1 LED3 LED4 ----------------- ----------------------- ---- ---- ------------ LED_STARTED NuttX has been started ON OFF OFF LED_HEAPALLOCATE Heap has been allocated OFF ON OFF LED_IRQSENABLED Interrupts enabled ON ON OFF LED_STACKCREATED Idle stack created ON ON OFF LED_INIRQ In an interrupt N/C N/C Soft glow LED_SIGNAL In a signal handler N/C N/C Soft glow LED_ASSERTION An assertion failed N/C N/C Soft glow LED_PANIC The system has crashed N/C N/C 2Hz Flashing LED_IDLE MCU is is sleep mode Not used After booting, LED1 and 3 are not longer used by the system and can be used for other purposes by the application (Of course, all LEDs are available to the application if CONFIG_ARCH_LEDS is not defined. Buttons ======= There are a total of five switches on-board. All pulled high and, hence, will be sensed as low when closed. SW1 Reset (not available to software) SW2 UBOOT UBOOT_SEL (?) SW3 Key_Back LCD1_D17/ATAD13/KP_IN7/SMC_VCCEN/EINT17/CSI1_D17/PH17 SW4 Key_Home LCD1_D18/ATAD14/KP_OUT0/SMC_SLK/EINT18/CSI1_D18/PH18 SW5 Key_Menu LCD1_D19/ATAD15/KP_OUT1/SMC_SDA/EINT19/CSI1_D19/PH19 Booting NuttX from an SD card ============================= These are the steps to get U-Boot booting from SD Card: $ git clone https://github.com/yuq/u-boot-sunxi.git $ cd u-boot-sunxi $ make pcduino CROSS_COMPILE=arm-none-eabi- $ sudo dd if=./spl/sunxi-spl.bin of=/dev/sdb bs=1024 seek=8 $ sudo dd if=nuttx.bin of=/dev/sdb bs=1024 seek=32 Reference: https://www.olimex.com/wiki/Bare_Metal_programming_A13#Stand_alone_program_running_with_uboot