/**************************************************************************** * boards/arm/sam34/sam3u-ek/include/board.h * * Copyright (C) 2009-2011, 2013 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ #ifndef __BOARDS_ARM_SAM34_SAM3U_EK_INCLUDE_BOARD_H #define __BOARDS_ARM_SAM34_SAM3U_EK_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include # ifdef CONFIG_SAM34_GPIO_IRQ # include # endif #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Clocking *****************************************************************/ /* After power-on reset, the sam3u device is running on a 4MHz internal RC. * These definitions will configure clocking * * MAINOSC: Frequency = 12MHz (crysta) * PLLA: PLL Divider = 1, Multiplier = 16 to generate PLLACK = 192MHz * Master Clock (MCK): Source = PLLACK, Prescalar = 1 to generate MCK = 96MHz * CPU clock: 96MHz */ /* Main oscillator register settings. * * The start up time should be should be: * Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles. */ #define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */ /* PLLA configuration. * * Divider = 1 * Multipler = 16 */ #define BOARD_CKGR_PLLAR_MUL (15 << PMC_CKGR_PLLAR_MUL_SHIFT) #define BOARD_CKGR_PLLAR_STMODE PMC_CKGR_PLLAR_STMODE_FAST #define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT) #define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS /* PMC master clock register settings. * * Source = PLLA * Divider = 2 */ #define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA #define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV2 /* USB UTMI PLL start-up time */ #define BOARD_CKGR_UCKR_UPLLCOUNT (3 << PMC_CKGR_UCKR_UPLLCOUNT_SHIFT) /* Resulting frequencies */ #define BOARD_MAINOSC_FREQUENCY (12000000) /* MAINOSC: 12MHz crystal on-board */ #define BOARD_PLLA_FREQUENCY (192000000) /* PLLACK: 16 * 12Mhz / 1 */ #define BOARD_MCK_FREQUENCY (96000000) /* MCK: PLLACK / 2 */ #define BOARD_CPU_FREQUENCY (96000000) /* CPU: MCK */ /* HSMCI clocking * * Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock (MCK) * divided by (2*(CLKDIV+1)). * * MCI_SPEED = MCK / (2*(CLKDIV+1)) * CLKDIV = MCI / MCI_SPEED / 2 - 1 * * Where CLKDIV has a range of 0-255. */ /* MCK = 96MHz, CLKDIV = 119, MCI_SPEED = 96MHz / 2 * (119+1) = 400 KHz */ #define HSMCI_INIT_CLKDIV (119 << HSMCI_MR_CLKDIV_SHIFT) /* MCK = 96MHz, CLKDIV = 3, MCI_SPEED = 96MHz / 2 * (3+1) = 12 MHz */ #define HSMCI_MMCXFR_CLKDIV (3 << HSMCI_MR_CLKDIV_SHIFT) /* MCK = 96MHz, CLKDIV = 1, MCI_SPEED = 96MHz / 2 * (1+1) = 24 MHz */ #define HSMCI_SDXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT) #define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV /* FLASH wait states * * FWS Max frequency * 1.62V 1.8V * --- ----- ------ * 0 24MHz 27MHz * 1 40MHz 47MHz * 2 72MHz 84MHz * 3 84MHz 96MHz */ #define BOARD_FWS 3 /* LED definitions **********************************************************/ #define LED_STARTED 0 /* LED0=OFF LED1=OFF LED2=OFF */ #define LED_HEAPALLOCATE 1 /* LED0=OFF LED1=OFF LED2=ON */ #define LED_IRQSENABLED 2 /* LED0=OFF LED1=ON LED2=OFF */ #define LED_STACKCREATED 3 /* LED0=OFF LED1=ON LED2=ON */ #define LED_INIRQ 4 /* LED0=XXX LED1=TOG LED2=XXX */ #define LED_SIGNAL 5 /* LED0=XXX LED1=XXX LED2=TOG */ #define LED_ASSERTION 6 /* LED0=TOG LED1=XXX LED2=XXX */ #define LED_PANIC 7 /* LED0=TOG LED1=XXX LED2=XXX */ /* Button definitions *******************************************************/ #define BUTTON1 1 /* Bit 0: Button 1 */ #define BUTTON2 2 /* Bit 1: Button 2 */ #endif /* __BOARDS_ARM_SAM34_SAM3U_EK_INCLUDE_BOARD_H */