#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

menu "LCD Driver Support"

menuconfig LCD
	bool "Graphic LCD Driver Support"
	default n
	---help---
		Drivers for parallel and serial LCD and OLED type devices.  These
		drivers support interfaces as defined in include/nuttx/lcd/lcd.h

		This selection is necessary to enable support for LCD drivers in
		drivers/lcd as well as for board-specific LCD drivers in the boards/
		subdirectories.

if LCD

config LCD_PACKEDMSFIRST
	bool
	default n

comment "Common Graphic LCD Settings"

config LCD_FRAMEBUFFER
	bool "LCD framebuffer front end"
	default n
	select FB_UPDATE
	---help---
		Enable a "front end" that converts an sequential LCD driver into a
		standard, NuttX frame buffer driver.

		NOTE: Some LCD drivers implement an internal framebuffer for
		efficiency reasons but do not export a framebuffer interface.  So
		those LCD cannot be used as framebuffer drivers.  If the option is
		available, then such internal framebuffer support should be
		disabled because this external common framebuffer interface will
		provide the necessary buffering.

config LCD_EXTERNINIT
	bool "External LCD Initialization"
	default n
	depends on LCD_FRAMEBUFFER
	---help---
		Define to support external LCD initialization by platform-specific
		code.  If this option is defined, then the LCD framebuffer
		emulation will call board_graphics_setup() to initialize the
		graphics device.  This option is necessary if display is used that
		cannot be initialized using the standard LCD interfaces.

menu "LCD driver selection"

config LCD_NOGETRUN
	bool "Write-only LCD"
	default n
	---help---
		Many LCD hardware interfaces provide only minimal graphics capability.  In
		particularly, many simple LCD interfaces are write only.  That is we, can
		write graphics data to the LCD device memory, but we cannot read it back.
		If the LCD hardware does not support reading the graphics memory, then
		this option should be defined so that the NX layer can taking alternative
		measures when the LCD is not readable.  For example, if the LCD is not
		readable, then NX will not attempt to support transparency.

		See also NX_WRITEONLY in the graphics support menu.

config LCD_MAXCONTRAST
	int "LCD maximum contrast"
	default 31 if AQM_1248A
	default 63 if LCD_SHARP_MEMLCD
	default 255 if LCD_P14201 || LCD_LCD1602
	default 63
	range 1 255
	---help---
		must be 63 with the Epson controller and 127 with
		the Phillips controller.

config LCD_MAXPOWER
	int "LCD maximum power"
	default 255 if LCD_LCD1602
	default 1
	range 1 255
	---help---
		Maximum value of LCD power setting.  This normally equates to brightness:
		The brighter the screen, the high the power usage.

		On LCDs that have a backlight, this value corresponds directly to that
		backlight setting.  Board-specific logic may place restrictions on this
		value.

comment "Graphic LCD Devices"

config LCD_P14201
	bool "Rit P1402 series display"
	default n
	---help---
		p14201.c.  Driver for RiT P14201 series display with SD1329 IC
		controller.  This OLED is used with older versions of the
		TI/Luminary LM3S8962 Evaluation Kit.

if LCD_P14201
config P14201_NINTERFACES
	int "Number of physical P14201 devices"
	default 1
	range 1 1
	---help---
		Specifies the number of physical P14201
		devices that will be supported.

config P14201_SPIMODE
	int "SPI mode"
	default 2
	range 0 3
	---help---
		Controls the SPI mode

config P14201_FREQUENCY
	int "SPI frequency"
	default 1000000
	---help---
		Define to use a different bus frequency,FIXME DEFAULT VALUE OK?

config P14201_FRAMEBUFFER
	bool "Enable P14201 GDDRAM cache"
	default y
	---help---
		If defined, accesses will be performed
		using an in-memory copy of the OLEDs GDDRAM.  This cost of this
		buffer is 128 * 96 / 2 = 6Kb.  If this is defined, then the driver
		will be fully functional. If not, then it will have the following
		limitations:

		Reading graphics memory cannot be supported, and

		All pixel writes must be aligned to byte boundaries.
		The latter limitation effectively reduces the 128x96 display to 64x96.

		NOTE: This option should not be used if CONFIG_LCD_FRAMBEBUFFER is
		enabled.  That options provides for a more generalized, external
		LCD framebuffer.  This internal framebuffer support should not be
		enabled with CONFIG_LCD_FRAMBEBUFFER because this external common
		framebuffer interface will provide the necessary buffering.
endif

config LCD_MAX7219
	bool "Matrix of 8x8 LEDs controlled by MAX7219"
	default n
	---help---
		Matrix of LEDs (8x8) controlled by MAX7219.
		You can use cluster of 8x8 chained together.

if LCD_MAX7219

config MAX7219_NHORIZONTALBLKS
	int "Number of 8x8 LEDs matrices in the horizontal (width)!"
	default 1
	---help---
		Specifies the number of physical 8x8 LED matrices that are
		connected together in the horizontal. In fact we have only
		a single strip, but it can be arranged in blocks creating
		physically horizontal/vertical columns/rows.

config MAX7219_NVERTICALBLKS
	int "Number of 8x8 LEDs matrices in the vertical (height)!"
	default 1
	---help---
		Specifies the number of physical 8x8 LED matrices that are
		connected together in the vertical. In fact we have only
		a single strip, but it can be arranged in blocks creating
		physically horizontal/vertical columns/rows.

config MAX7219_INTENSITY
	int "Default LED Matrix bright intensity"
	default 10
	range 0 15
	---help---
		Specifies the default LEDs bright intensity to use.

endif # LCD_MAX7219

config LCD_MIO283QT2
	bool "MIO283QT-2 TFT LCD Display Module"
	default n
	---help---
		OLED Display Module, MIO283QT-2, Multi-Inno Technology, Co.
		based on the Himax HX8347-D LCD controller.

config LCD_MIO283QT9A
	bool "MIO283QT-9A TFT LCD Display Module"
	default n
	---help---
		Selects the driver for the MI0283QT-9A LCD from Multi-Inno
		Technology Co., Ltd.  This LCD is based on the Ilitek ILI9341
		LCD controller.

config LCD_UG9664HSWAG01
	bool "UG-9664HSWAG01 OLED Display Module"
	default n
	depends on SPI
	---help---
		OLED Display Module, UG-9664HSWAG01, Univision Technology Inc.  Used
		with the LPCXpresso and Embedded Artists base board.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

		Required SPI driver settings:
		SPI_CMDDATA - Include support for cmd/data selection.

if LCD_UG9664HSWAG01

config UG9664HSWAG01_SPIMODE
	int "UG-9664HSWAG01 SPI Mode"
	default 0
	range 0 3
	---help---
		Controls the SPI mode

config UG9664HSWAG01_FREQUENCY
	int "UG-9664HSWAG01 SPI Frequency"
	default 3500000
	---help---
		Define to use a different bus frequency

config UG9664HSWAG01_NINTERFACES
	int "Number of UG-9664HSWAG01 Devices"
	default 1
	---help---
		Specifies the number of physical UG-9664HSWAG01 devices that will be
		supported.  NOTE:  At present, this must be undefined or defined to be 1.

config UG9664HSWAG01_POWER
	bool "Power control"
	default n
	---help---
		If the hardware supports a controllable OLED a power supply, this
		configuration should be defined.  In this case the system must
		provide an interface ug_power().

endif

config LCD_SH1106_OLED_132
	bool "Generic 0.96'' OLED Display Module (SH1106/SSD1306)"
	default n
	select LCD_SSD1306
	---help---
		0.96'' OLED Display Module, featuring an SH1106, typically advertised as
		SSD1306. Mostly similar to "UG2864HSWEG01" although it uses the full
		132x28 pixels.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

config LCD_UG2864HSWEG01
	bool "UG-2864HSWEG01 OLED Display Module (SSD1306)"
	default n
	select LCD_SSD1306
	---help---
		OLED Display Module, UG-2864HSWEG01, Univision Technology Inc based
		on the Solomon Tech SSD1306 LCD controller.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

		Required SPI driver settings:
		SPI_CMDDATA - Include support for cmd/data selection.

config LCD_UG2832HSWEG04
	bool "UG-2832HSWEG04 OLED Display Module (SSD1306)"
	default n
	select LCD_SSD1306
	---help---
		OLED Display Module, UG-UG2832HSWEG04, Univision Technology Inc
		based on the Solomon Tech SSD1306 LCD controller.  Used with the
		Atmel SAM4L Xplained Pro board on the OLED1 module.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

		Required SPI driver settings:
		SPI_CMDDATA - Include support for cmd/data selection.

config LCD_DD12864WO4A
	bool "DD-12864WO-4A OLED Display Module"
	default n
	select LCD_SSD1306
	select SPI_CMDDATA
	---help---
		OLED Display Module, DD-12864WO-4A, Densitron Technologies
		based on the Solomon Tech SSD1309 LCD controller.  Used with the
		ThingseeOne board.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

		Required SPI driver settings:
		SPI_CMDDATA - Include support for cmd/data selection.

config LCD_HILETGO
	bool "HiletGO 128x64 OLED"
	default n
	select LCD_SSD1306
	select SPI_CMDDATA
	---help---
		HiletGo 129x64 OLED Display Module, featuring an SSD1306.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

config LCD_SSD1306
	bool

if LCD_SSD1306

choice
	prompt "SSD1306 Interface"
	default LCD_SSD1306_SPI

config LCD_SSD1306_SPI
	bool "SSD1306 on SPI Interface"
	select SPI
	---help---
		Enables support for the SPI interface.

config LCD_SSD1306_I2C
	bool "SSD1306 on I2C Interface"
	select I2C
	---help---
		Enables support for the I2C interface

endchoice # SSD1306 Interface
endif # LCD_SSD1306

if LCD_SSD1306_SPI

config SSD1306_SPIMODE
	int "SSD1306 SPI Mode"
	default 0 if !LCD_DD12864WO4A
	default 3 if LCD_DD12864WO4A
	range 0 3
	---help---
		Selects the SPI mode used with the SSD1306 device

config SSD1306_FREQUENCY
	int "SSD1306 SPI Frequency"
	default 3500000 if !LCD_DD12864WO4A
	default 10000000 if LCD_DD12864WO4A
	---help---
		Selects the SPI bus frequency used with the SSD1306 device

#config SSD1306_NINTERFACES
#	int "Number of SSD1306 Devices"
#	default 1
#	---help---
#		Specifies the number of physical SSD1306 devices that will be
#		supported.  NOTE:  At present, this must be undefined or defined to
#		be 1.

endif # LCD_SSD1306_SPI

if LCD_SSD1306_I2C

config SSD1306_I2CADDR
	int "SSD1306 I2C Address"
	default 60
	---help---
		7-bit I2C Address of SSD1306.  Typical addresses are 0x3c (60) or
		0x3d (61).  NOTE that these correspond to the 8-bit addresses
		0x78 or 0x7a that you may see in documentation.

config SSD1306_I2CFREQ
	int "SSD1306 I2C Frequency"
	default 400000
	---help---
		I2C Frequency to communicate with SSD1306

endif # LCD_SSD1306_I2C

config LCD_SSD1351
	bool "SSD1351 OLED Display Module"
	default n
	---help---
		OLED Display Module, SSD1351, Solomon Systech.

if LCD_SSD1351

choice
	prompt "Interface"
	default SSD1351_SPI4WIRE

config SSD1351_PARALLEL8BIT
	bool "8-bit Parallel Interface"
	---help---
		Enables support for the 8-bit parallel interface.

config SSD1351_SPI3WIRE
	bool "3-wire SPI Interface"
	select SPI
	---help---
		Enables support for the 3-wire SPI interface.

config SSD1351_SPI4WIRE
	bool "4-wire SPI Interface"
	select SPI
	select SPI_CMDDATA
	---help---
		Enables support for the 4-wire SPI interface.

endchoice

if SSD1351_SPI3WIRE || SSD1351_SPI4WIRE

config SSD1351_SPIMODE
	int "SPI Mode"
	default 0
	range 0 3
	---help---
		Specifies the SPI mode.

config SSD1351_SPIFREQ
	int "SPI Frequency"
	default 1000000
	---help---
		Specifies the SPI frequency.

endif

config SSD1351_NINTERFACES
	int "Number of SSD1351 Devices"
	default 1
	range 1 1
	---help---
		Specifies the number of physical SSD1351 devices that will
		be supported.

config SSD1351_XRES
	int "X Resolution"
	default 128
	range 1 128
	---help---
		Specifies the X resolution of the display.

config SSD1351_YRES
	int "Y Resolution"
	default 128
	range 1 128
	---help---
		Specifies the Y resolution of the display.

config SSD1351_MIRRORX
	bool "Mirror X"
	default n
	---help---
		Mirrors the display along the X axis.

config SSD1351_MIRRORY
	bool "Mirror Y"
	default n
	---help---
		Mirrors the display along the Y axis.

config SSD1351_INVERT
	bool "Invert Display"
	default n
	---help---
		Inverts the display.

config SSD1351_VDDEXT
	bool "External VDD"
	default n
	---help---
		Specifies that VDD is external.

config SSD1351_TRST
	int "Reset Period"
	default 5
	range 5 31
	---help---
		Specifies the reset period in DCLKs.

config SSD1351_TPRECHG1
	int "First Pre-charge Period"
	default 8
	range 3 15
	---help---
		Specifies the first pre-charge period in DCLKs.

config SSD1351_PERFENHANCE
	bool "Enhance Display Performance"
	default n
	---help---
		Enhances the display performance.

config SSD1351_CLKDIV
	int "Clock Divider"
	default 0
	range 0 10
	---help---
		Specifies the clock divider.

config SSD1351_OSCFREQ
	int "Oscillator Frequency"
	default 15
	range 0 15
	---help---
		Specifies the oscillator frequency.

config SSD1351_TPRECHG2
	int "Second Pre-charge Period"
	default 8
	range 1 15
	---help---
		Specifies the second pre-charge period in DCLKs.

config SSD1351_VPRECHG
	int "Voltage Pre-charge Level"
	default 50
	range 20 60
	---help---
		Specifies the pre-charge voltage level as a percentage of VCC.

config SSD1351_VCOMH
	int "COM Deselect Voltage Level"
	default 82
	range 72 86
	---help---
		Specifies the COM deselect voltage level as a percentage of VCC.

config SSD1351_CONTRASTA
	int "Color A Contrast"
	default 138
	range 0 255
	---help---
		Specifies the contrast of color A.

config SSD1351_CONTRASTB
	int "Color B Contrast"
	default 81
	range 0 255
	---help---
		Specifies the contrast of color B.

config SSD1351_CONTRASTC
	int "Color C Contrast"
	default 138
	range 0 255
	---help---
		Specifies the contrast of color C.

config SSD1351_MSTRCONTRAST
	int "Master Contrast Ratio"
	default 16
	range 1 16
	---help---
		Specifies the master contrast ratio in sixteenths.

endif

config LCD_ST7735
	bool "Sitronix ST7735 TFT Controller"
	default n

if LCD_ST7735
	config LCD_ST7735_GM00
		bool "132x162 Display Resolution"
		default n
		---help---
			Two resolutions are availabe, either the 132x162 or
			the 128x160

	config LCD_ST7735_BPP
		int "Bit Per Pixel (12, 16 or 18)"
		default 16

	config LCD_ST7735_SPIMODE
		int "SPI Mode"
		default 0

	config LCD_ST7735_FREQUENCY
		int "SPI Frequency"
		default 3000000

endif # LCD_ST7735

config LCD_PCD8544
	bool "Nokia 5110 LCD Display (Philips PCD8544)"
	default n
	---help---
		LCD Display Module, PCD8544, Philips

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.

if LCD_PCD8544

config PCD8544_NINTERFACES
	int "Number of PCD8544 Devices"
	default 1
	---help---
		Specifies the number of physical PCD8544 devices that will be
		supported.  NOTE:  At present, this must be undefined or defined to be 1.

config PCD8544_XRES
	int "PCD8544 X Resolution"
	default 84
	---help---
		Specifies the X resolution of the LCD.

config PCD8544_YRES
	int "PCD8544 Y Resolution"
	default 48
	---help---
		Specifies the Y resolution of the LCD.

config PCD8544_INVERSE_VIDEO
	bool "PCD8544 Inverse video"
	default n
	---help---
		Inverse video on LCD.

endif # LCD_PCD8544

config LCD_ST7565
	bool "ST7565 LCD Display Module"
	default n
	---help---
		LCD Display Module, ST7565, Univision Technology Inc.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.

if LCD_ST7565

choice
	prompt "LCD Display Module initialization sequence"
	default NHD_C12864KGZ

config NHD_C12864KGZ
	bool "like NHD C12864KGZ"

config ERC_12864_3
	bool "like ERC12864-3"

config AQM_1248A
	bool "like AQM1248A"

endchoice

config ST7565_NINTERFACES
	int "Number of ST7565 Devices"
	default 1
	---help---
		Specifies the number of physical ST7565 devices that will be
		supported.  NOTE:  At present, this must be undefined or defined to be 1.

config ST7565_XRES
	int "ST7565 X Resolution"
	default 128
	---help---
		Specifies the X resolution of the LCD.

config ST7565_YRES
	int "ST7565 Y Resolution"
	default 48 if AQM_1248A
	default 64
	---help---
		Specifies the Y resolution of the LCD.

config ST7565_MIRROR_X
	bool "ST7565 apply mirror on X"
	default n
	---help---
		Mirror X on LCD.

config ST7565_MIRROR_Y
	bool "ST7565 apply mirror on Y"
	default y if AQM_1248A
	default n
	---help---
		Mirror Y on LCD.

config ST7565_INVERSE_VIDEO
	bool "ST7565 Inverse video"
	default n
	---help---
		Inverse video on LCD.

endif # LCD_ST7565

config LCD_ST7567
	bool "ST7567 LCD Display Module"
	default n
	---help---
		LCD Display Module, ST7567, Univision Technology Inc.  Used
		with the LPCXpresso and Embedded Artists base board.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

		Required SPI driver settings:
		SPI_CMDDATA - Include support for cmd/data selection.

if LCD_ST7567

config ST7567_SPIMODE
	int "ST7567 SPI Mode"
	default 0
	range 0 3
	---help---
		Controls the SPI mode

config ST7567_FREQUENCY
	int "ST7567 SPI Frequency"
	default 3500000
	---help---
		Define to use a different bus frequency

config ST7567_NINTERFACES
	int "Number of ST7567 Devices"
	default 1
	---help---
		Specifies the number of physical ST7567 devices that will be
		supported.  NOTE:  At present, this must be undefined or defined to be 1.

config ST7567_POWER
	bool "Power control"
	default n
	---help---
		If the hardware supports a controllable LCD a power supply, this
		configuration should be defined.  In this case the system must
		provide an interface ug_power().

config ST7567_XRES
	int "ST7567 X Resolution"
	default 128
	---help---
		Specifies the X resolution of the LCD.

config ST7567_YRES
	int "ST7567 Y Resolution"
	default 64
	---help---
		Specifies the Y resolution of the LCD.

endif # LCD_ST7567

config LCD_UG2864AMBAG01
	bool "UG-2864AMBAG01 OLED Display Module"
	default n
	---help---
		OLED Display Module, UG-2864AMBAG01, Univision Technology Inc.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

		Required SPI driver settings:
		SPI_CMDDATA - Include support for cmd/data selection.

if LCD_UG2864AMBAG01

config UG2864AMBAG01_SPIMODE
	int "UG-2864AMBAG01 SPI Mode"
	default 3
	range 0 3
	---help---
		Controls the SPI mode

config UG2864AMBAG01_FREQUENCY
	int "UG-2864AMBAG01 SPI Frequency"
	default 3500000
	---help---
		Define to use a different bus frequency

config UG2864AMBAG01_NINTERFACES
	int "Number of UG-2864AMBAG01 Devices"
	default 1
	---help---
		Specifies the number of physical UG-9664HSWAG01 devices that will be
		supported.  NOTE:  At present, this must be undefined or defined to be 1.

endif

config LCD_SSD1289
	bool "LCD Based on SSD1289 Controller"
	default n
	---help---
		Enables generic support for any LCD based on the Solomon Systech,
		Ltd, SSD1289 Controller.  Use of this driver will usually require so
		detailed customization of the LCD initialization code as necessary
		for the specific LCD driven by the SSD1289 controller.

if LCD_SSD1289

choice
	prompt "SSD1289 Initialization Profile"
	default SSD1289_PROFILE1

config SSD1289_PROFILE1
	bool "Profile 1"

config SSD1289_PROFILE2
	bool "Profile 2"

config SSD1289_PROFILE3
	bool "Profile 3"

endchoice
endif

config LCD_SHARP_MEMLCD
	bool "Sharp Memory LCD Suite"
	default n
	---help---
		memlcd.c. Driver for Sharp Memory LCD Suite.

if LCD_SHARP_MEMLCD

choice
	prompt "Memory LCD Model"
	default MEMLCD_LS013B7DH03

config MEMLCD_LS013B7DH01
	bool "LS013B7DH01"
	---help---
		Selects the LS013B7DH01 model

config MEMLCD_LS013B7DH03
	bool "LS013B7DH03"
	---help---
		Selects the LS013B7DH03 model

endchoice

config MEMLCD_NINTERFACES
	int "Number of physical Memory LCD devices"
	default 1
	range 1 1
	---help---
		Specifies the number of physical Memory LCD devices that will
		be supported.

config MEMLCD_EXTCOMIN_MODE_HW
	bool "Use hardware mode for EXTCOMIN"
	default n
	---help---
		If use hardware mode to toggle VCOM, we need to send specific
		command at a constant frequency to trigger the LCD internal
		hardware logic.  While use software mode, we set up a timer to
		toggle EXTCOMIN connected IO, basically, it is a hardware
		timer to ensure a constant frequency.

config MEMLCD_SPI_FREQUENCY
	int "SPI frequency"
	default 3500000
	---help---
		Define to use a different bus frequency, FIXME DEFAULT VALUE OK?

endif

choice
	prompt "LCD Orientation"
	default LCD_LANDSCAPE
	depends on LCD
	---help---
		Some LCD drivers may support displays in different orientations.
		If the LCD driver supports this capability, than these are configuration
		options to select that display orientation.

config LCD_LANDSCAPE
	bool "Landscape orientation"
	---help---
		Define for "landscape" orientation support.  Landscape mode refers one
		of two orientations where the display is wider than it is tall
		(LCD_RLANDSCAPE is the other).  This is the default orientation.

config LCD_PORTRAIT
	bool "Portrait orientation"
	---help---
		Define for "portrait" orientation support.  Portrait mode refers one
		of two orientations where the display is taller than it is wide
		(LCD_RPORTAIT is the other).

config LCD_RPORTRAIT
	bool "Reverse portrait display"
	---help---
		Define for "reverse portrait" orientation support.  Reverse portrait mode
		refers one of two orientations where the display is taller than it is
		wide (LCD_PORTAIT is the other).

config LCD_RLANDSCAPE
	bool "Reverse landscape orientation"
	---help---
		Define for "reverse landscape" orientation support.  Reverse landscape mode
		refers one of two orientations where the display is wider than it is
		tall (LCD_LANDSCAPE is the other).

endchoice

config LCD_LPM013M091A
	bool "JDI LPM013M091A LCD Driver"
	default n
	---help---
		JDI LPM013M091A LCD Driver.
		This driver doesn't support reading data.
		Recommended to use DMA to transfer data or displayed image would be
		broken.

config LCD_ILI9340
	bool "ILI9340 LCD Single Chip Driver"
	default n
	---help---
		LCD Single Chip Driver, ILI9340, ILI Technology Corp.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

config LCD_ILI9340_NINTERFACES
	int "Number of supported display driver"
	range 1 2
	default 1
	depends on LCD_ILI9340
	---help---
		Define the number of supported  displays driven by a ili9340 LCD Single
		Chip Driver.

config LCD_ILI9340_IFACE0
	bool "(1) LCD Display"
	depends on LCD_ILI9340_NINTERFACES = 1 || LCD_ILI9340_NINTERFACES = 2
	---help---
		Configure first LCD Display.

if LCD_ILI9340_IFACE0
choice
	prompt "LCD Orientation"
	default LCD_ILI9340_IFACE0_LANDSCAPE
	---help---
		Configure display orientation.

config LCD_ILI9340_IFACE0_LANDSCAPE
	bool "Landscape orientation"
	---help---
		Define for "landscape" orientation support.

config LCD_ILI9340_IFACE0_PORTRAIT
	bool "Portrait orientation"
	---help---
		Define for "portrait" orientation support.

config LCD_ILI9340_IFACE0_RLANDSCAPE
	bool "Reverse landscape orientation"
	---help---
		Define for "reverse landscape" orientation support.

config LCD_ILI9340_IFACE0_RPORTRAIT
	bool "Reverse portrait display"
	---help---
		Define for "reverse portrait" orientation support.

endchoice

choice
	prompt "Color format"
	default LCD_ILI9340_IFACE0_RGB565
	---help---
		LCD color format.

config LCD_ILI9340_IFACE0_RGB565
	bool "16 bpp RGB565 color format"
	---help---
	16 bpp RGB565 color format

endchoice
endif

config LCD_ILI9340_IFACE1
	bool "(2) LCD Display"
	depends on LCD_ILI9340_NINTERFACES = 2
	---help---
		Configure second LCD Display.

if LCD_ILI9340_IFACE1
choice
	prompt "LCD Orientation"
	default LCD_ILI9340_IFACE1_LANDSCAPE
	---help---
		Configure display orientation.

config LCD_ILI9340_IFACE1_LANDSCAPE
	bool "Landscape orientation"
	---help---
		Define for "landscape" orientation support.

config LCD_ILI9340_IFACE1_PORTRAIT
	bool "Portrait orientation"
	---help---
		Define for "portrait" orientation support.

config LCD_ILI9340_IFACE1_RLANDSCAPE
	bool "Reverse landscape orientation"
	---help---
		Define for "reverse landscape" orientation support.

config LCD_ILI9340_IFACE1_RPORTRAIT
	bool "Reverse portrait display"
	---help---
		Define for "reverse portrait" orientation support.

endchoice

choice
	prompt "Color format"
	default LCD_ILI9340_IFACE1_RGB565
	---help---
		LCD color format.

config LCD_ILI9340_IFACE1_RGB565
	bool "16 bpp RGB565 color format"
	---help---
		16 bpp RGB565 color format

endchoice
endif

config LCD_ILI9341
	bool "ILI9341 LCD Single Chip Driver"
	default n
	---help---
		LCD Single Chip Driver, ILI9341, ILI Technology Corp. Used
		with the STM32F429i Discovery Board.

		Required LCD driver settings:
		LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
		LCD_MAXPOWER should be 1:  0=off, 1=on

config LCD_ILI9341_NINTERFACES
	int "Number of supported display driver"
	range 1 2
	default 1
	depends on LCD_ILI9341
	---help---
		Define the number of supported  displays driven by a ili9341 LCD Single
		Chip Driver.

config LCD_ILI9341_IFACE0
	bool "(1) LCD Display"
	depends on LCD_ILI9341_NINTERFACES = 1 || LCD_ILI9341_NINTERFACES = 2
	---help---
		Configure first LCD Display.

if LCD_ILI9341_IFACE0
choice
	prompt "LCD Orientation"
	default LCD_ILI9341_IFACE0_LANDSCAPE
	---help---
		Configure display orientation.

config LCD_ILI9341_IFACE0_LANDSCAPE
	bool "Landscape orientation"
	---help---
		Define for "landscape" orientation support.

config LCD_ILI9341_IFACE0_PORTRAIT
	bool "Portrait orientation"
	---help---
		Define for "portrait" orientation support.

config LCD_ILI9341_IFACE0_RLANDSCAPE
	bool "Reverse landscape orientation"
	---help---
		Define for "reverse landscape" orientation support.

config LCD_ILI9341_IFACE0_RPORTRAIT
	bool "Reverse portrait display"
	---help---
		Define for "reverse portrait" orientation support.

endchoice

choice
	prompt "Color format"
	default LCD_ILI9341_IFACE0_RGB565
	---help---
		LCD color format.

config LCD_ILI9341_IFACE0_RGB565
	bool "16 bpp RGB565 color format"
	---help---
		16 bpp RGB565 color format

endchoice
endif

config LCD_ILI9341_IFACE1
	bool "(2) LCD Display"
	depends on LCD_ILI9341_NINTERFACES = 2
	---help---
		Configure second LCD Display.

if LCD_ILI9341_IFACE1
choice
	prompt "LCD Orientation"
	default LCD_ILI9341_IFACE1_LANDSCAPE
	---help---
		Configure display orientation.

config LCD_ILI9341_IFACE1_LANDSCAPE
	bool "Landscape orientation"
	---help---
		Define for "landscape" orientation support.

config LCD_ILI9341_IFACE1_PORTRAIT
	bool "Portrait orientation"
	---help---
		Define for "portrait" orientation support.

config LCD_ILI9341_IFACE1_RLANDSCAPE
	bool "Reverse landscape orientation"
	---help---
		Define for "reverse landscape" orientation support.

config LCD_ILI9341_IFACE1_RPORTRAIT
	bool "Reverse portrait display"
	---help---
		Define for "reverse portrait" orientation support.

endchoice

choice
	prompt "Color format"
	default LCD_ILI9341_IFACE1_RGB565
	---help---
		LCD color format.

config LCD_ILI9341_IFACE1_RGB565
	bool "16 bpp RGB565 color format"
	---help---
		16 bpp RGB565 color format

endchoice
endif

config LCD_LCDDRV_SPIIF
	bool "Generic SPI Interface Driver (for ILI9341 or others)"
	default n
	depends on LCD_ILI9341
	---help---
		SPI Interface shim to allow LCD and ePaper to be bound to
		a normal SPI port.

config LCD_LCDDRV_SPEED
        int "Generic SPI Interface speed"
	default 10000000
	depends on LCD_LCDDRV_SPIIF
	---help---
		SPI Interface speed. According to the specification this is generally
		quite limited, but people have had success with much faster
		speeds than the spec sheets say. YMMV.

config LCD_RA8875
	bool "RA8875 LCD Display Controller"
	default n
	---help---
		LCD controller driver for RA8875 by RAiO Technologies Inc.

if LCD_RA8875

choice
	prompt "MCU Interface width"
	default LCD_RA8875_8BIT
	---help---
		Bit-width of MCU interface (8 or 16)

config LCD_RA8875_8BIT
	bool "8 bit"

config LCD_RA8875_16BIT
	bool "16 bit"

endchoice # MCU Interface width

choice
	prompt "Colors"
	default LCD_RA8875_65K
	---help---
		Number of colors/color depth

config LCD_RA8875_256
	bool "256 / 8 bit"

config LCD_RA8875_65K
	bool "65k / 16 bit"

endchoice # Colors

config LCD_RA8875_EXTENDED
	bool "Extended drawing interfaces"
	default n
	depends on BUILD_FLAT
	---help---
		Build in some non-standard, custom drawing interfaces for the RA8875
		including the following: ra8875_drawrectangle(), ra8875_drawline(),
		ra8875_drawtriangle(), and ra8875_drawcircle().  NOTE that these
		will not be accessible by applications in protected or kernel build
		configurations.

		NOTE: The non-standard ra8875_clear(), ra8875_drawrectangle(),
		ra8875_drawline() interfaces are always built and available for use
		because within the OS because these are used internally by the
		driver anyway.

endif # LCD_RA8875

config LCD_FT80X
	bool "FTDI FT80x GUI Controller"
	default n
	select SCHED_HPWORK
	---help---
		Integrated LCD, Audio, Touchscreen controller driver for the FTDI
		FT80x "EVE" series.

if LCD_FT80X

choice
	prompt "FTDI FT80x part"
	default LCD_FT800

config LCD_FT800
	bool "FT800"

config LCD_FT801
	bool "FT801"

endchoice # FTDI FT80x part

choice
	prompt "FTDI FT80x Interface"
	default LCD_FT80X_SPI

config LCD_FT80X_SPI
	bool "SPI"
	select SPI

config LCD_FT80X_I2C
	bool "I2C"
	select I2C

endchoice # FTDI FT80x Interface

config LCD_FT801_MULTITOUCH
	bool "FT801 Multi-touch"
	default n
	depends on LCD_FT801

choice
	prompt "Display size"
	default LCD_FT80X_WQVGA

config LCD_FT80X_WQVGA
	bool "WQVGA 480x272"

config LCD_FT80X_QVGA
	bool "QVGA 320x240"

endchoice # Display size

choice
	prompt "Audio Shutdown Options"
	default LCD_FT80X_AUDIO_NOSHUTDOWN

config LCD_FT80X_AUDIO_NOSHUTDOWN
	bool "No amplifier shutdown control"
	---help---
		There is no audio amplifier or the audio amplifier is not under
		software control.

config LCD_FT80X_AUDIO_MCUSHUTDOWN
	bool "MCU controls audio shutdown"
	---help---
		The audio amplifier is controlled via an MCU GPIO output pin.

config LCD_FT80X_AUDIO_GPIOSHUTDOWN
	bool "FT80X controls audio shutdown"
	---help---
		The audio amplifier is controlled via an FT80x GPIO output pin.

endchoice # Audio Shutdown Option

config LCD_FT80X_AUDIO_GPIO
	int "FT80x audio shutdown GPIO"
	default 0
	range 0 1
	depends on LCD_FT80X_AUDIO_GPIOSHUTDOWN
	---help---
		Identifies the GPIO pin used to control the amplifier shutdown
		output.

endif # LCD_FT80X

endmenu # LCD Driver selection
endif # LCD

comment "Character/Segment LCD Devices"

menuconfig SLCD
	bool "Alphanumeric/Segment LCD Devices"
	default n
	---help---
		Drivers for Alphanumeric and Segment LCDs (SLCDs).  These
		drivers support interfaces as defined in include/nuttx/lcd/slcd_ioctl.h
		amd slcd_codec.h

		This selection is necessary to enable support for SLCD drivers in
		drivers/lcd as well as for board-specific LCD drivers in the boards/
		subdirectories.

if SLCD

config SLCD_CONSOLE
	bool "SLCD console output"
	default n
	---help---
		It is possible to use an SLCD to provide console output.  This option
		enables that possibility.

		At present, only one architecture supports this option (M16C).
		However, this feature could be provided by other architectures in
		the future.

config LCD_LCD1602
	bool "LCD 1602"
	default n
	---help---
		Enable support for LCD1602 devices.  LCD1602 is based on the Hitachi
		HD44780U LCD controller.  See also include/nuttx/lcd/hd4478ou.h.

		NOTE:  There is no common implementation of the LCD1602 driver.
		Rather, there are board-by-board implementations.

config LCD_BACKPACK
	bool "PCF8574 LCD Backpack"
	default n
	depends on I2C
	select LIB_SLCDCODEC
	---help---
		Enable support for PCF8574 LCD Backpack driver. This driver supports
		an interface board that is based on the PCF8574 io expander and
		supports the HD44780-based (or compatible) LCD modules.  There are
		a myriad of different vendors of such, but they are principally the
		same, save wiring and minor features like jumpers for I2C addresses.
		This driver supports known and unknown variants.

		See pcf8574_lcd_backpack_readme.txt

config LCD_ST7032
	bool "ST7032 over I2C (i.e. JLX1602G-390)"
	default n
	depends on I2C
	---help---
		Enable support for ST7032i on I2C. This driver was tested with
		JLX1602G-390 that has 10 pins: CAP1N, CAP1P, VOUT, VCC, SHLS,
		SHLC, GND, SDA, SCL, XRESET. The XRESET pin is connected to a
		pull-up resistor, then the module automatically executes power-on
		reset when power is supplied to the module. The pin SHLS is also
		connected to a pull-up resistor and the pin SHLC is connected to
		the ground. So only I2C pins SDA and SCL are used by NuttX.

endif # SLCD

comment "Other LCD-related Devices"

config LCD_OTHER
	bool
	default n

config LCD_TDA19988
	bool "TDA19988 HDMI Encoder"
	default n
	select LCD_OTHER
	depends on I2C && EXPERIMENTAL
	---help---
		Enable support for the TI TDA19988 HDMI Encoder.  The TDA19988 is a
		very low power and very small size High-Definition Multimedia
		Interface (HDMI) 1.4a transmitter.  This device is primarily
		intended for mobile applications like Digital Video Camera (DVC),
		Digital Still Camera (DSC), Portable Multimedia Player (PMP), Mobile
		Phone and Ultra-Mobile Personal Computer (UM PC), new PC tablet and
		MID where size and power are key for battery autonomy.

endmenu # LCD Driver Support