/**************************************************************************** * arch/x86/include/i486/arch.h * * Copyright (C) 2011, 2015 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ /* This file should never be included directed but, rather, * only indirectly through nuttx/arch.h */ #ifndef __ARCH_X86_INCLUDE_I486_ARCH_H #define __ARCH_X86_INCLUDE_I486_ARCH_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include # include #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* FLAGS bits */ #define X86_FLAGS_CF (1 << 0) /* Bit 0: Carry Flag */ /* Bit 1: Reserved */ #define X86_FLAGS_PF (1 << 2) /* Bit 2: Parity Flag */ /* Bit 3: Reserved */ #define X86_FLAGS_AF (1 << 4) /* Bit 4: Auxillary carry Flag */ /* Bit 5: Reserved */ #define X86_FLAGS_ZF (1 << 6) /* Bit 6: Zero Flag */ #define X86_FLAGS_SF (1 << 7) /* Bit 7: Sign Flag */ #define X86_FLAGS_TF (1 << 8) /* Bit 8: Trap Flag */ #define X86_FLAGS_IF (1 << 9) /* Bit 9: Interrupt Flag */ #define X86_FLAGS_DF (1 << 10) /* Bit 10: Direction Flag */ #define X86_FLAGS_OF (1 << 11) /* Bit 11: Overflow Flag */ #define X86_FLAGS_IOPL_SHIFT (12) /* Bits 12-13: IOPL mask (286+ only)*/ #define X86_FLAGS_IOPL_MASK (3 << X86_FLAGS_IOPL_SHIFT) #define X86_FLAGS_NT (1 << 14) /* Bit 14: Nested Task */ /* Bit 15: Reserved */ /* EFLAGS bits (Extend the basic FLAGS bit definitions) */ #define X86_EFLAGS_RF (1 << 16) /* Bit 16: Resume Flag (386+ only) */ #define X86_EFLAGS_VM (1 << 17) /* Bit 17: Virtual Mode (386+ only) */ #define X86_EFLAGS_AC (1 << 18) /* Bit 18: Alignment Check (486SX+ only) */ #define X86_EFLAGS_VIF (1 << 19) /* Bit 19: Virtual Interrupt Flag (Pentium+) */ #define X86_EFLAGS_VIP (1 << 20) /* Bit 20: Virtual Interrupt Pending (Pentium+) */ #define X86_EFLAGS_ID (1 << 21) /* Bit 21: CPUID detection flag (Pentium+) */ /* Programmable Interrupt Controller (PIC) */ /* Operational Control Words * * The first instruction the Operation Control Word 1 (OCW1) to set which * IRQ's to mask and which IRQ's not to. */ #define PIC1_OCW1 0x20 #define PIC2_OCW1 0xa0 # define PIC1_OCW1_IRQ0 (1 << 0) /* IRQ0 System Timer */ # define PIC1_OCW1_IRQ1 (1 << 1) /* IRQ1 Keyboard */ # define PIC1_OCW1_IRQ2 (1 << 2) /* IRQ2 PIC2 */ # define PIC1_OCW1_IRQ3 (1 << 3) /* IRQ3 Serial Port */ # define PIC1_OCW1_IRQ4 (1 << 4) /* IRQ4 Serial Port */ # define PIC1_OCW1_IRQ5 (1 << 5) /* IRQ5 Reserved/Sound Card */ # define PIC1_OCW1_IRQ6 (1 << 6) /* IRQ6 Floppy Disk Controller */ # define PIC1_OCW1_IRQ7 (1 << 7) /* IRQ7 Parallel Port */ # define PIC1_OCW1_ALL # define PIC2_OCW1_IRQ8 (1 << 0) /* IRQ8 Real Time Clock */ # define PIC2_OCW1_IRQ9 (1 << 1) /* IRQ9 Redirected IRQ2 */ # define PIC2_OCW1_IRQ10 (1 << 2) /* IRQ10 Reserved */ # define PIC2_OCW1_IRQ11 (1 << 3) /* IRQ11 Reserved */ # define PIC2_OCW1_IRQ12 (1 << 4) /* IRQ12 PS/2 Mouse */ # define PIC2_OCW1_IRQ13 (1 << 5) /* IRQ13 Maths Co-Processor */ # define PIC2_OCW1_IRQ14 (1 << 6) /* IRQ14 Hard Disk Drive */ # define PIC2_OCW1_IRQ15 (1 << 7) /* IRQ15 Reserved */ # define PIC2_OCW1_ALL /* Operation Control Word 2 selects how the End of Interrupt (EOI) procedure * works. The only thing of interest to us in this register is the non- * specific EOI command, which we must send at the end of our ISR's. */ #define PIC1_OCW2 0x20 #define PIC2_OCW2 0xa0 # define PIC_OCW2_ACT_SHIFT (0) # define PIC_OCW2_ACT_MASK (7 << PIC_OCW2_ACT_SHIFT) # define PIC1_OCW2_ACT_IRQ0 (0 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 0 */ # define PIC1_OCW2_ACT_IRQ1 (1 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 1 */ # define PIC1_OCW2_ACT_IRQ2 (2 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 2 */ # define PIC1_OCW2_ACT_IRQ3 (3 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 3 */ # define PIC1_OCW2_ACT_IRQ4 (4 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 4 */ # define PIC1_OCW2_ACT_IRQ5 (5 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 5 */ # define PIC1_OCW2_ACT_IRQ6 (6 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 6 */ # define PIC1_OCW2_ACT_IRQ7 (7 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 7 */ # define PIC2_OCW2_ACT_IRQ8 (0 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 8 */ # define PIC2_OCW2_ACT_IRQ9 (1 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 9 */ # define PIC2_OCW2_ACT_IRQ10 (2 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 10 */ # define PIC2_OCW2_ACT_IRQ11 (3 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 11 */ # define PIC2_OCW2_ACT_IRQ12 (4 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 12 */ # define PIC2_OCW2_ACT_IRQ13 (5 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 13 */ # define PIC2_OCW2_ACT_IRQ14 (6 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 14 */ # define PIC2_OCW2_ACT_IRQ15 (7 << PIC_OCW2_ACT_SHIFT) /* Act on IRQ 15 */ # define PIC_OCW2_EOI_SHIFT (5) # define PIC_OCW2_EOI_MASK (7 << PIC_OCW2_EOI_SHIFT) # define PIC_OCW2_EOI_AUTO (0 << PIC_OCW2_EOI_SHIFT) /* Rotate in Auto EOI Mode (Clear) */ # define PIC_OCW2_EOI_NONSPEC (1 << PIC_OCW2_EOI_SHIFT) /* Non Specific EOI */ # define PIC_OCW2_EOI_SPEC (3 << PIC_OCW2_EOI_SHIFT) /* Specific EOI */ # define PIC_OCW2_EOI_RAUTO (4 << PIC_OCW2_EOI_SHIFT) /* Rotate in Auto EOI Mode (Set) */ # define PIC_OCW2_EOI_RNSPEC (5 << PIC_OCW2_EOI_SHIFT) /* Rotate on Non-Specific EOI */ # define PIC_OCW2_EOI_PRIO (6 << PIC_OCW2_EOI_SHIFT) /* Set Priority Command (Use Bits 2:0) */ # define PIC_OCW2_EOI_RSPEC (7 << PIC_OCW2_EOI_SHIFT) /* Rotate on Specific EOI (Use Bits 2:0) */ /* Operation Control Word 3. Bits 0 and 1 bitsenable us to read the status * of the Interrupt Request Register (IRR) and the In-Service Register (ISR). * This is done by setting the appropriate bits correctly and reading the * register at the Base Address. * * For example if we wanted to read the In-Service Register (ISR), then we * would set both bits 1 and 0 to 1. The next read to the base register, * (0x20 for PIC1 or 0xa0 for PIC2) will return the status of the In-Service * Register. */ #define PIC1_OCW3 0x20 #define PIC2_OCW3 0xa0 # define PIC_OCW3_PCMD_SHIFT (0) /* Poll command */ # define PIC_OCW3_PCMD_MASK (3 << PIC_OCW3_PCMD_SHIFT) # define PIC_OCW3_PCMD_IRR (2 << PIC_OCW3_PCMD_SHIFT) /* Next Read Returns Interrupt Request Register */ # define PIC_OCW3_PCMD_ISR (3 << PIC_OCW3_PCMD_SHIFT) /* Next Read Returns In-Service Register */ # define PIC_OCW3_POLLCMD (1 << 2) /* Poll command */ # define PIC_OCW3_ONE (1 << 3) /* Must be set to 1 */ # define PIC_OCW3_SM_SHIFT (5) # define PIC_OCW3_SM_MASK (3 << PIC_OCW3_SM_SHIFT) # define PIC_OCW3_RSM (2 << PIC_OCW3_SM_SHIFT) /* Reset Special Mask */ # define PIC_OCW3_SSM (3 << PIC_OCW3_SM_SHIFT) /* Set Special Mask */ /* If the PIC has been reset, it must be initialized with 2 to 4 Initialization * Command Words (ICW) before it will accept and process Interrupt Requests. The * following outlines the four possible Initialization Command Words. */ #define PIC1_ICW1 0x20 #define PIC2_ICW1 0xa0 # define PIC_ICW1_ICW4 (1 << 0) /* Will be Sending ICW4 (no ICW4) */ # define PIC_ICW1_SINGLE (1 << 1) /* Single PIC (vs. Cascaded pics) */ # define PIC_ICW1_INTERVAL (1 << 2) /* Call Address Interval of 4 (vs 8) */ # define PIC_ICW1_LEVEL (1 << 3) /* Level Triggered Interrupts (vs Edge) */ # define PIC_ICW1_ICW1 (1 << 4) /* Must be set to 1 for ICW1 */ # define PIC_ICW1_VEC_SHIFT (5) /* Interrupt Vector Addresses for MCS-80/85 Mode */ # define PIC_ICW1_VEC_MASK (7 << PIC_ICW1_VEC_SHIFT) /* Initialization Command Word 2 (ICW2) selects which vector information is * released onto the bus, during the 2nd INTA Pulse. Using the 8086 mode, * only bits 7:3 need to be used. This will be 00001000 (0x08) for PIC1 and * 01110000 (0x70) for PIC2. If you wish to relocate the IRQ Vector Table, * then you can use this register. */ #define PIC1_ICW2 0x21 #define PIC2_ICW2 0xa1 /* There are two different Initialization Command Word 3's. One is used, if * the PIC is a master, while the other is used for slaves. */ #define PIC1_ICW3 0x21 #define PIC2_ICW3 0xa1 /* Master ICW3 */ # define PIC1_ICW3_IRQ0 (1 << 0) /* IRQ0 is connected to a Slave */ # define PIC1_ICW3_IRQ1 (1 << 1) /* IRQ1 is connected to a Slave */ # define PIC1_ICW3_IRQ2 (1 << 2) /* IRQ2 is connected to a Slave */ # define PIC1_ICW3_IRQ3 (1 << 3) /* IRQ3 is connected to a Slave */ # define PIC1_ICW3_IRQ4 (1 << 4) /* IRQ4 is connected to a Slave */ # define PIC1_ICW3_IRQ5 (1 << 5) /* IRQ5 is connected to a Slave */ # define PIC1_ICW3_IRQ6 (1 << 6) /* IRQ6 is connected to a Slave */ # define PIC1_ICW3_IRQ7 (1 << 7) /* IRQ7 is connected to a Slave */ /* And for the slave device, the ICW3 below is used. */ # define PIC_ICW3_SID_MASK (0) /* Slave ID */ # define PIC_ICW3_SID_SHIFT (7 << PIC_ICW3_SID_MASK) # define PIC_ICW3_SID0 (0 << PIC_ICW3_SID_MASK) /* Slave 0 */ # define PIC_ICW3_SID1 (1 << PIC_ICW3_SID_MASK) /* Slave 1 */ # define PIC_ICW3_SID2 (2 << PIC_ICW3_SID_MASK) /* Slave 2 */ # define PIC_ICW3_SID3 (3 << PIC_ICW3_SID_MASK) /* Slave 3 */ # define PIC_ICW3_SID4 (4 << PIC_ICW3_SID_MASK) /* Slave 4 */ # define PIC_ICW3_SID5 (5 << PIC_ICW3_SID_MASK) /* Slave 5 */ # define PIC_ICW3_SID6 (6 << PIC_ICW3_SID_MASK) /* Slave 6 */ # define PIC_ICW3_SID7 (7 << PIC_ICW3_SID_MASK) /* Slave 7 */ #define PIC1_ICW4 0x21 #define PIC2_ICW4 0xa1 # define PIC_ICW4_FNM (1 << 4) /* Special Fully Nested Mode */ # define PIC_ICW4_BMODE_SHIFT (2) /* Bufferd mode */ # define PIC_ICW4_BMODE_MASK (3 << PIC_ICW4_BMODE_SHIFT) # define PIC_ICW4_BMODE_NON (0 << PIC_ICW4_BMODE_SHIFT) /* Non - Buffered Mode */ # define PIC_ICW4_BMODE_SLAVE (2 << PIC_ICW4_BMODE_SHIFT) /* Buffered Mode - Slave */ # define PIC_ICW4_BMODE_MSTR (3 << PIC_ICW4_BMODE_SHIFT) /* Buffered Mode - Master */ # define PIC_ICW4_AEOI (1 << 1) /* Auto EOI */ # define PIC_ICW4_808xMODE (1 << 0) /* 8086/8080 Mode (vs MCS-80/85) */ /* Interrupt Mask Register */ #define PIC1_IMR 0x21 #define PIC2_IMR 0xa1 # define PIC1_IMR_IRQ0 (1 << 0) /* IRQ0 System Timer */ # define PIC1_IMR_IRQ1 (1 << 1) /* IRQ1 Keyboard */ # define PIC1_IMR_IRQ2 (1 << 2) /* IRQ2 PIC2 */ # define PIC1_IMR_IRQ3 (1 << 3) /* IRQ3 Serial Port */ # define PIC1_IMR_IRQ4 (1 << 4) /* IRQ4 Serial Port */ # define PIC1_IMR_IRQ5 (1 << 5) /* IRQ5 Reserved/Sound Card */ # define PIC1_IMR_IRQ6 (1 << 6) /* IRQ6 Floppy Disk Controller */ # define PIC1_IMR_IRQ7 (1 << 7) /* IRQ7 Parallel Port */ # define PIC1_IMR_ALL 0xff # define PIC2_IMR_IRQ8 (1 << 0) /* IRQ8 Real Time Clock */ # define PIC2_IMR_IRQ9 (1 << 1) /* IRQ9 Redirected IRQ2 */ # define PIC2_IMR_IRQ10 (1 << 2) /* IRQ10 Reserved */ # define PIC2_IMR_IRQ11 (1 << 3) /* IRQ11 Reserved */ # define PIC2_IMR_IRQ12 (1 << 4) /* IRQ12 PS/2 Mouse */ # define PIC2_IMR_IRQ13 (1 << 5) /* IRQ13 Maths Co-Processor */ # define PIC2_IMR_IRQ14 (1 << 6) /* IRQ14 Hard Disk Drive */ # define PIC2_IMR_IRQ15 (1 << 7) /* IRQ15 Reserved */ # define PIC2_IMR_ALL 0xff /* Programmable Interrupt Timer Definitions */ #define PIT_REG_COUNTER0 0x40 #define PIT_REG_COUNTER1 0x41 #define PIT_REG_COUNTER2 0x42 #define PIT_REG_COMMAND 0x43 /* PIT command bit defintions */ # define PIT_OCW_BINCOUNT_BCD (1 << 0) /* vs binary */ # define PIT_OCW_MODE_SHIFT (1) # define PIT_OCW_MODE_MASK (7 << PIT_OCW_MODE_SHIFT) # define PIT_OCW_MODE_TMCNT (0 << PIT_OCW_MODE_SHIFT) /* Terminal count */ # define PIT_OCW_MODE_ONESHOT (1 << PIT_OCW_MODE_SHIFT) /* One shot */ # define PIT_OCW_MODE_RATEGEN (2 << PIT_OCW_MODE_SHIFT) /* Rate gen */ # define PIT_OCW_MODE_SQUARE (3 << PIT_OCW_MODE_SHIFT) /* Square wave generation */ # define PIT_OCW_MODE_SWTRIG (4 << PIT_OCW_MODE_SHIFT) /* Software trigger */ # define PIT_OCW_MODE_HWTRIG (5 << PIT_OCW_MODE_SHIFT) /* Hardware trigger */ # define PIT_OCW_RL_SHIFT (4) # define PIT_OCW_RL_MASK (3 << PIT_OCW_RL_SHIFT) # define PIT_OCW_RL_LATCH (0 << PIT_OCW_RL_SHIFT) # define PIT_OCW_RL_LSBONLY (1 << PIT_OCW_RL_SHIFT) # define PIT_OCW_RL_MSBONLY (2 << PIT_OCW_RL_SHIFT) # define PIT_OCW_RL_DATA (3 << PIT_OCW_RL_SHIFT) # define PIT_OCW_COUNTER_SHIFT (6) # define PIT_OCW_COUNTER_MASK (3 << PIT_OCW_COUNTER_SHIFT) # define PIT_OCW_COUNTER_0 (0 << PIT_OCW_COUNTER_SHIFT) # define PIT_OCW_COUNTER_1 (1 << PIT_OCW_COUNTER_SHIFT) # define PIT_OCW_COUNTER_2 (2 << PIT_OCW_COUNTER_SHIFT) /**************************************************************************** * Public Types ****************************************************************************/ /* GDT data structures ****************************************************** * * The Global Descriptor Table or GDT is a data structure used by Intel x86- * family processors starting with the 80286 in order to define the * characteristics of the various memory areas used during program execution, * for example the base address, the size and access privileges like * executability and writability. These memory areas are called segments in * Intel terminology. */ /* This structure defines one segment */ struct gdt_entry_s { uint16_t lowlimit; /* The lower 16 bits of the limit */ uint16_t lowbase; /* The lower 16 bits of the base */ uint8_t midbase; /* The next 8 bits of the base */ uint8_t access; /* Access flags, determine ring segment can be used in */ uint8_t granularity; uint8_t hibase; /* The last 8 bits of the base */ } packed_struct; /* This structure refers to the array of GDT entries, and is in the format * required by the lgdt instruction. */ struct gdt_ptr_s { uint16_t limit; /* The upper 16 bits of all selector limits */ uint32_t base; /* The address of the first GDT entry */ } packed_struct; /* IDT data structures ****************************************************** * * The Interrupt Descriptor Table (IDT) is a data structure used by the x86 * architecture to implement an interrupt vector table. The IDT is used by the * processor to determine the correct response to interrupts and exceptions. */ struct idt_entry_s { uint16_t lobase; /* Lower 16-bits of vector address for interrupt */ uint16_t sel; /* Kernel segment selector */ uint8_t zero; /* This must always be zero */ uint8_t flags; /* (See documentation) */ uint16_t hibase; /* Upper 16-bits of vector address for interrupt */ } packed_struct; /* A struct describing a pointer to an array of interrupt handlers. This is * in a format suitable for giving to 'lidt'. */ struct idt_ptr_s { uint16_t limit; uint32_t base; /* The address of the first GDT entry */ } packed_struct; /**************************************************************************** * Inline functions ****************************************************************************/ #ifndef __ASSEMBLY__ /* Return stack pointer */ static inline uint32_t up_getsp() { uint32_t regval; asm volatile( "\tmovl %%esp, %0\n" : "=rm" (regval) : : "memory"); return regval; } /* Get segment registers */ static inline uint32_t up_getds() { uint32_t regval; asm volatile( "\tmov %%ds, %0\n" : "=rm" (regval) : : "memory"); return regval; } static inline uint32_t up_getcs() { uint32_t regval; asm volatile( "\tmov %%cs, %0\n" : "=rm" (regval) : : "memory"); return regval; } static inline uint32_t up_getss() { uint32_t regval; asm volatile( "\tmov %%ss, %0\n" : "=rm" (regval) : : "memory"); return regval; } /**************************************************************************** * Public Types ****************************************************************************/ /**************************************************************************** * Public Data ****************************************************************************/ /**************************************************************************** * Public Function Prototypes ****************************************************************************/ #ifdef __cplusplus #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif void gdt_flush(uint32_t gdt_addr); void idt_flush(uint32_t idt_addr); #undef EXTERN #ifdef __cplusplus } #endif #endif /* __ASSEMBLY__ */ #endif /* __ARCH_X86_INCLUDE_I486_ARCH_H */